Publications

The boundary layer concept is applied to the flow around the nose of a streamlined train. In general, that flow is not axisymmetric due to the shape of the nose and the crosswind component of the relative incoming velocity. This departure from axisymmetry produces a transverse pressure gradient that is responsible for skewing an otherwise plane boundary layer. An empirical correlation, dependent on the longitudinal velocity and one unknown parameter, is used to represent the transverse velocity profile. The value of that unknown parameter is obtained from the momentum equations integrated streamwise inside the boundary layer. A visual comparison was carried out between the numerical simulations and the skin shear pattern of a scale model in a wind tunnel. The qualitative results compare well, the numerical model being able to locate the position of the main longitudinal vortices on the lee side of the train.

Masonry buildings worldwide exhibited severe damage and collapse in recent strong earthquake events. It is known that their brittle behavior, which is mainly due to the combination of low tensile strength, large mass and insufficient connection between structural elements, is the main limitation for their structural implementation in residential buildings. A new construction system for masonry buildings using concrete blocks units and trussed reinforcement is presented here and its seismic behavior is validated through shaking table tests. Dynamic tests of two geometrically identical two-story reduced scale (1:2) models have been carried out, considering artificial accelerograms compatible with the elastic response spectrum defined by the Eurocode 8. The first model was reinforced with the new proposed system while the second model was built with unreinforced masonry. The experimental analysis encompasses local and global parameters such as cracking patterns, failure mechanisms, and in-plane and out-of-plane behavior in terms of displacements and lateral drifts from where the global dynamic behavior of the two buildings is analyzed comparatively. Finally, behavior factors for the design recommendations in case of unreinforced masonry are also evaluated.

The out-of-plane response of walls in existing stone masonry buildings is one of the major causes of vulnerability commonly observed in post-earthquake damage surveys. In this context, a shaking table (ST) test campaign was carried out on a full-scale masonry façade mainly focusing on the characterization of its out-of-plane overturning behaviour. The structure tested on the ST is a partial reproduction of an existing building from Azores, damaged during the 9 July 1998 Faial earthquake. The definition of the tested specimen as well as the selection of the input ground motion is reported in this paper. A specific emphasis is given to the definition of the time-history to be applied during the tests because it was felt as an essential and crucial part of the work to obtain the desired overturning behaviour. The accelerogram to be imposed was selected from a large set of accelerograms (74) by means of a step-by-step procedure on the basis of several numerical analyses resorting to the rocking response of rigid blocks.

The present work describes a shaking table experimental campaign specifically developed for the characterisation of the out-of-plane response of a full scale stone masonry façade. After the description of the specimen and the selection of the input motion presented in a companion paper (Part 1), the experimental campaign is illustrated and extensively described. The out-of-plane behaviour of the sacco masonry façade is presented in terms of displacements, velocities, and accelerations recorded during the shaking table tests. A one-sided rocking response of the façade was observed prior to collapse. The impacts were clearly identified in the acceleration records. The façade overturning occurred with the expected failure mode, as predicted in the design of the test.Finally, some conclusions are drawn regarding the observed behaviour and particular features of this type of stone masonry constructions, which may influence the global behaviour of the façade.

During seismic action, energy dissipation in structures occurs in structural and non-structural components, as well as in the substructure. Several of these dissipative mechanisms are modelled explicitly in nonlinear dynamic analyses, notably through relatively sophisticated hysteretic finite elements. Nevertheless, in most practical applications, it is not possible to simulate all the physical contributions to energy dissipation.Structural engineers are thus constrained to overcome this limitation by a mathematical artifice, in the form of equivalent linear viscous damping, which accounts for the remaining

A utilização de dispositivos de dissipação de energia é vista como forma eficiente para proteger estruturas contra ações sísmicas. Os dispositivos Amortecedores de Líquido Sintonizados (ALS) são uma forma simples mas eficaz para reduzir a resposta de estruturas face a ações dinâmicas. Este artigo descreve simulações numéricas sobre o comportamento de ALS, isolados e/ou incluídos numa estrutura de transmissão, comparando-as com os resultados obtidos experimentalmente. Para o efeito foi usado um software de acesso livre denominado CLAWPACK com potencialidades para simular os fenómenos que ocorrem no interior de ALSs. O CLAWPACK consiste num conjunto de rotinas em Fortran desenvolvidas para obtenção de soluções numéricas de sistemas hiperbólicos de equações parcialmente diferenciais no tempo, como é o caso dos fenómenos não-lineares subjacentes à shallow water wave theory. Foram necessárias adaptações e ajustes em algumas das rotinas principais para permitir a simulação das excitações dinâmicas pretendidas. Nas simulações numéricas são variados alguns parâmetros, em que se incluem a altura de água, a amplitude de excitação e o número de dispositivos. Os principais resultados obtidos são comparados, com os resultados obtidos experimentalmente, tanto para dispositivos isolados como para dispositivos incluídos nas estruturas ensaiadas. As principais conclusões obtidas serão também apresentadas.

N/A

As tubagens enterradas constituem componentes principais de sistemas que permitem assegurar o bem estar e o desenvolvimento da sociedade, nomeadamente no que respeita ao abastecimento de água, à drenagem de águas residuais, ao transporte de energia e à comunicação.Com a consolidação das malhas urbanas, tem-se assistido a uma crescente preocupação, não só com a construção, mas em especial com a fase de utilização desses sistemas, tanto nas atividades de exploração (operação e manutenção) como de fim de vida (reabilitação e substituição). Adicionalmente, existe um conjunto crescente de preocupações mais vasto do que as questões operacionais correntes, que inclui os efeitos de fenómenos naturais, como os sismos. As abordagens de gestão do risco permitem ter em conta estes fenómenos e lidar explicitamente com a incerteza que lhes está associada.No contexto da problemática da gestão do risco sísmico de tubagens enterradas, apresenta-se um levantamento de modelos para avaliação da respetiva vulnerabilidade. No âmbito deste artigo é proposta uma abordagem para incorporar a variabilidade probabilística na modelação da vulnerabilidade sísmica de tubagens enterradas. Os resultados obtidos com a metodologia proposta são comparados com a gama de variação da vulnerabilidade sísmica apresentada pela American Lifelines Alliance.

N/A

N/A

O trabalho apresentado refere-se à avaliação do comportamento aerodinâmico da ponte pedonal suspensa 516 Arouca. Para tal realizaram-se ensaios em túnel de vento sobre um modelo reduzido de modo a obter os seus coeficientes aerodinâmicos estáticos e a resposta dinâmica.Os ensaios estáticos contemplaram diferentes configurações: i) tabuleiro; ii) tabuleiro e catenárias; iii) tabuleiro com pessoas, e; iv) tabuleiro e pórticos de suporte aos cabos de estabilização. Para os ensaios dinâmicos foi ensaiado apenas o tabuleiro.Para estes últimos ensaios, dado que o principal modo de deslocamento é lateral (em baloiço), houve que implementar um esquema de suspensão apropriado.

Os edifícios tipo

As estruturas de alvenaria têm nos demonstrado ao longo dos anos grande suscetibilidade perante a ação dos sismos. Para que possam ser definidas e implementadas estratégias de mitigação é importante compreender a vulnerabilidade destas estruturas.O presente estudo pretende analisar o comportamento de duas paredes de alvenaria, com e sem reforço, sujeitas a ações cíclicas no seu plano e sob carregamento vertical. Como proposta de reforço e melhoria do comportamento da parede foi utilizada rede de fibra de vidro e argamassa à base de cal. Numa primeira fase será utilizado um programa de cálculo avançado para análises não lineares, baseado na formulação do Applied Element Method (AEM) [1], de forma a prever o comportamento das paredes até ao colapso. Os resultados serão comparados e discutidos sendo feita a validação experimental do modelo numérico e da formulação utilizada.

The response of three full-scale unreinforced masonry buildings, without specific seismic detailing, as observed in shake table testing at LNEC for a seismic action representative of induced seismicity, is presented. The first building specimen simulated the upper floor and roof of the end-unit of a two-storey terraced house, built with unreinforced cavity walls, a reinforced concrete slab and a pitched timber roof. The second specimen was a replica of the roof of the first building. The third specimen represented instead a one-story detached pre-1940

Até à introdução e disseminação do atual regulamento de dimensionamento sismorresistente em 1983, o Regulamento de Segurança e Acções para Estruturas de Edifícios e Pontes (RSA), a generalidade dos edifícios de betão armado eram dimensionados para resistir apenas a cargas gravíticas. O presente estudo pretende caracterizar o comportamento sísmico destes edifícios bem como quantificar a fiabilidade estrutural quando avaliados à luz do Eurocódigo 8 - Parte 3.Por forma a criar um contexto representativo desta classe de edifícios, foram gerados centenas de modelos numéricos que refletem as principais características geométricas e mecânicas dos materiais, e que obedecem às regras e disposições construtivas definidas nos regulamentos nacionais anteriores à introdução do RSA. A análise probabilística dos resultados obtidos para os níveis de perigosidade associados às diferentes regiões doterritório nacional fornece indicações de quais as combinações edifícios/zonas sísmicas que apresentam uma maior vulnerabilidade face à ação sísmica.

A avaliação da segurança sísmica de edifícios existentes tem como quadro de referência a NP EN 1998-3; 2017. A complexidade destes procedimentos, aliada ao reconhecimento de que uma parte significativa do território nacional apresenta uma sismicidade média/baixa, torna a aplicação desta norma complexa para a maioria dos edifícios existentes de pequeno a médio porte.Neste contexto, foi desenvolvido um estudo probabilístico com o objetivo de definir dois procedimentos alternativos que, não pretendendo substituir a regulamentação existente, permitem avaliar a segurança sísmica de edifícios de uma forma expedita, com base nas propriedades geométricas e mecânicas dos seus elementos verticais.Não obstante a sua simplicidade, estes métodos permitem assegurar o mesmo nível de fiabilidade estrutural para os diferentes graus de perigosidade sísmica em Portugal, bem como um nível de segurança inversamente proporcional ao nível de complexidade dos mesmos, tendo como referência a NP EN 1998-3; 2017.

Typical low-rise masonry construction in regions such as Europe, Australia and New Zealand consists of cavity or solid URM walls covered with various timber roof configurations generally supported by masonry gables. The flexibility of these light timber roof systems has been reported to have significant effect on the seismic performance of the structure as a whole. Post-earthquake observations and experimental outcomes highlighted the large vulnerability of the URM gable walls to the development of overturning mechanisms, both due to the out-of-plane excitations and the in-plane timber diaphragm deformability. This paper presents a full-scale collapse shake-table test on a Dutch roof substructure composed by wooden planks supported by timber beams lying on masonry gable walls. After attaining the collapse of the gable walls, the timber roof diaphragm was subjected to a supplementary quasi-static cyclic pushover test for a complete characterization of the system response. The test is a part of a wider research project aimed at assessing the vulnerability of URM buildings in Groningen, a region of the Netherlands not naturally prone to seismic events, but which has recently been exposed to induced seismicity. The presented results include the damage evolution, the collapse mechanism and the hysteretic response of the specimen.

This paper discusses the results of three dynamic shake-table tests, performed on full-scale unreinforced masonry buildings without specific seismic detailing. The testing program is part of a wider research project aimed at assessing the seismic vulnerability of buildings typical of the Groningen region, located in Northeast of the Netherlands. This area, historically not prone to tectonic ground motions, in the recent years has been subjected to earthquakes induced by reservoir depletion due to gas extraction. The first building specimen simulated the end-unit of a two-story terraced house, built with unreinforced cavity walls. These walls were composed of an inner load-bearing leaf, made of calcium silicate bricks supporting the floors, and an outer veneer, made of clay bricks with aesthetic and weather-protection function. The two leafs were interconnected by distributed metal ties. The floors consisted of reinforced concrete slabs, providing rigid diaphragms in their plane. The pitched roof was made of longitudinal timber purlins, supported by end gables perpendicular to the shaking direction, and wood boards. The second specimen was a replica of the second story and the attic of the first building, with identical details for walls, slab, and roof framing tested to study the collapse mechanism. The third specimen represented instead a one-story detached pre-1940s house, built with double-wythe unreinforced clay masonry walls. The prototype structure was designed to include large openings and a re-entrant corner, causing significant horizontal irregularities. The first floor was made of timber beams and planks, resulting in a flexible diaphragm. The steep-pitch roof consisted of a series of timber trusses connected by wood purlins and boards. The two façades perpendicular to the shaking direction were designed in order to represent two common gable geometries.

Seismic risk has been the focus of a number of European projects in recent years, but there has never been a concerted effort amongst the research community to produce a uniform European risk model. The H2020 SERA project has a work package that is dedicated to that objective, with the aim being to produce an exposure model, a set of fragility/vulnerability functions, and socio-economic indicators in order to assess probabilistic seismic risk at a European scale. The partners of the project are working together with the wider seismic risk community through web tools, questionnaires, workshops, and meetings. All of the products of the project will be openly shared with the community on both the OpenQuake platform of the Global Earthquake Model (GEM) and the web platform of the European Facilities for Earthquake Hazard and Risk (EFEHR).

Reinforced concrete (RC) frames subjected to seismic loading often depict localized member-end deformations due to strain penetration effects between adjacent members, such as beam-column and column-footing joints. Past experimental programs indicate that the bond-slip deformations occurring at the interface between the reinforcement and the surrounding concrete can contribute up to 40% of the lateral deformation of the RC members.Despite the recognized importance of strain penetration effects on the response of RC structures, the consideration of such effects in numerical models is still limited. The employment of advanced bond-slip models within detailed finite element formulations, capable of simulating continuous domains with highly discretized meshes, has witnessed great advances over the recent years with encouraging results. Nonetheless, this modelling approach is computationally heavy and hence inapplicable for practical seismic (nonlinear) analysis of structures.Alternatively, the use of beam-column elements with lumped or distributed plasticity is a more computationally efficient and engineering-friendly modelling approach. Unfortunately, the elements of this type available in conventional numerical packages did not yet consider an explicit simulation of the interface between the reinforcing bars and the surrounding concrete along their embedment length. In other words, the inclusion of bond-slip effects in beam element models has been essentially achieved through simplified formulations based on empirical relationships.The present study aimed at overcoming the foregoing limitation by developing an explicit bond-slip model applicable to general fibre-based beam-column elements. Using a state-of-the-art bond-slip constitutive model, the current paper introduces a zero-length element that computes the localized member-end deformations accounting for the bond-slip response at each reinforcing bar of a given RC section. Along with the material properties and anchorage conditions, the proposed nonlinear model also accounts for cyclic degradation and rebar yielding effects. Validation studies conducted with the proposed numerical formulation reveal a good agreement with past experimental tests, evidencing an important stability and accuracy at the expense of an acceptable additional computational effort.

This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe

The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.

The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies

Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.

In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.

O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.

Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107

Most of the Lisbon 18th century timber-framed masonry

Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.

When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko

A non

N/A

This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM

Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte

Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.

O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação

O presente estudo teve como objetivo a caracterização dinâmica e do comportamento mecânico da estrutura do edifício Sede I da EDP, para uma adequada simulação do seu comportamento sísmico. Neste relatório descrevem-se os ensaios de identificação dinâmica in situ realizados, com base em vibrações ambiente e em vibrações forçadas, com o objetivo de recolher informação sobre as propriedades dinâmicas da estrutura como um todo e das suas lajes dos pisos elevados em particular. Foi efetuado o registo e a análise dos sinais de aceleração devido a vibração ambiente, medidos em diversos pontos do edifício, bem como devido a vibrações forçadas impostas num dos pisos enterrados do edifício. São também apresentados e analisados os ensaios de caracterização do comportamento mecânico de componentes estruturais relacionadas com a ligação das lajes mistas dos pisos elevados às paredes dos núcleos resistentes de betão armado do edifício. Estes consistem em ensaios destrutivos de troços de laje mista ligados aos núcleos, por meio de varões selados à parede, e em ensaios de arrancamento desses varões, tendo como objetivo caracterizar os materiais e componentes dos elementos estruturais. Esta informação é essencial para a posterior calibração dos modelos numéricos da estrutura e para uma realista simulação do seu comportamento sísmico, bem como para uma eventual deteção de anomalias estruturais decorrentes de patologias que possam comprometer o desempenho do edifício face à ocorrência de sismos.

A avaliação da segurança sísmica de edifícios existentes tem como quadro de referência o Eurocódigo 8

Nos estudos probabilísticos para avaliação da perigosidade sísmica, são estabelecidas zonas de geração sísmica (zonas sismogénicas), representando regiões que partilham as mesmas caraterísticas sismológicas, tectónicas e geológicas e definidas as relações entre a frequência com que aí ocorrem os sismos e as respetivas magnitudes, num dado período de tempo. Em 2006, para o Anexo Nacional do Eurocódigo 8, foram consideradas e caraterizadas 11 zonas Sismogénicas para Portugal continental, adaptadas de estudos previamente elaborados em 1996. Entre 2008 e 2009, no âmbito dos projetos ERSTA e SHARE, foram propostas novas zonas sismogénicas, e estimados os respetivos parâmetros da lei de frequência - magnitude. Estas diferentes propostas resultaram em diferentes mapas de perigosidade sísmica para Portugal continental. A SPES, Sociedade Portuguesa de Engenharia Sísmica, espelhando a inquietude existente na comunidade científica face às diversas expressões da perigosidade sísmica em Portugal, e consciente da necessidade de um consenso perante os agentes decisores, considerou urgente a realização de um estudo criterioso acerca das opções tomadas, nos diferentes estudos, e suas implicações. É nestecontexto que surge este trabalho, que pretende fazer uma análise crítica e comparativa dos resultadosobtidos nos diferentes estudos mencionados e as suas implicações ao nível dos períodos de retorno para sismos de maior magnitude. Numa parte II, serão estudadas as implicações em termos de valores da perigosidade sísmica, para vários períodos de retorno e frequências espetrais.

O presente relatório, elaborado no âmbito de um estudo em curso no LNEC sobre a segurança sísmica das construções nas intervenções de reabilitação, sintetiza os instrumentos jurídicos e os conceitos relevantes para a análise do atual regime jurídico da reabilitação urbana (RJRU), e do regime excecional de reabilitação urbana (RERU).

This document reports the outcomes of the research project

This document reports the outcome of the seismic test on the Rusticasa building, the first in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a log house system (LHS). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.

This document reports the outcome of the seismic test on the LegnoCase building, the second in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of OSB panels (PF-OSB). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.

This document reports the outcome of the seismic test on the RubnerHaus building, the third in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of gypsum fibre panel (PF-GF). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.

This document reports the outcome of the seismic test on the TUGraz building, the fourth in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a cross laminated system (CTL). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.

The TIMBER BUILDINGS Project, led by the University of Trento, included testing of four full scale multi-story timber houses with a realistic horizontal plan and three types of timber housing systems: platform frame system (PFS), log house system (LHS) and cross laminated timber (CLT). The tests were carried in the LNEC-3D shake table under different levels of excitation and different conditions of the structure.The tests were carried with the goal of assessing the seismic performance of the buildings, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.The results were presented in separate reports, one for each building. This document contains information common to the remaining four reports.

Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.

Análise da forma das edificações nas ações do vento

As condicionantes arquitetónicas e de urbanização na ventilação natural

Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento