Publicações

This study aims to evaluate the effect of mineral fillers on bitumen ageing. Two different bitumens and four mastics were investigated in the unaged and long-term aged states, based on different properties (consistency, rheology, fatigue resistance and ductility). Mastics stiffened less due to ageing treatment than bitumens, especially with granite filler. However, the results of the performance tests were not definitive regarding the effect of the filler. Aged bitumen showed greater fatigue resistance and higher specific energy of ductile fracture than unaged bitumen, whereas the mastics showed minor variations in the specific energy of ductile fracture with ageing treatment, which is indicative of less ageing, but the fatigue resistance decreased significantly in mastics with one of the bitumens.

This paper presents an experimental and numerical study about the durability of adhesively bonded joints between pultruded glass fibre reinforced polymer (GFRP) adherends for civil engineering applications. Single lap joint (SLJ) specimens were manufactured using either epoxy (EP) or polyurethane (PUR) adhesive and exposed to the following hygrothermal and outdoor ageing conditions for up to 730 days: water and salt water immersion at 20 °C and 40 °C, continuous condensation at 40 °C, salt fog spray at 35 ºC, and outdoor ageing in Lisbon, Portugal. At predetermined times, the mechanical behaviour of the SLJs was assessed through shear tests, in a dry condition. Results obtained show that hygrothermal ageing detrimentally affected the failure load and stiffness of the SLJs made with both adhesives, although this degradation was balanced to some extent by post-curing effects and the desorption period. The magnitude of such degradation was not significantly influenced by the immersion media, but was largely affected by temperature. Outdoor ageing did not cause significant changes in terms of stiffness; for both adhesives, ultimate load presented a moderate increasing trend, with cyclic pattern, reflecting the effects of seasonal changes in weather. For both adhesives, failure always initiated in one of the GFRP adherends, regardless of the ageing process. However, ageing seemed to affect the portion of bond area with either (light) fibre-tear or adhesive failure: in EP-GFRP specimens, the area with adhesive failure (initially null) increased due to ageing, while in PUR-GFRP specimens (significant in unaged joints) it decreased. The final part of the paper presents non-linear finite element (FE) models of the SLJs; these models were developed to numerically simulate the mechanical performance of the joints and to estimate the influence of ageing on the bond vs. slip laws that describe the interaction between the GFRP adherends.

Fibre Reinforced Polymer (FRP) composites have been the source of an increasing interest in the field of rehabilitation, namely for repair and strengthening of reinforced concrete (RC) structures. One of the most effective techniques comprises externally bonded FRP composites, in which the efficacy of rehabilitation depends considerably on the integrity and durability of the bond established between the FRP and the substrate, which is provided by a structural adhesive. This paper presents a concise review of critical durability issues associated with the structural bond between FRP and concrete for rehabilitation purposes. A number of factors determining the durability of FRP-concrete bonded joints have been identified and grouped into the following categories: materials – adhesive and adherends, joint characteristics and in-service conditions. For each of those factors, the main findings obtained in previous studies are summarized and the aspects that need fuarther investigation are outlined.

This paper presents an experimental study about the effects of thermal cycles on adhesively bonded joints between pultruded glass fibre reinforced polyester (GFRP) adherends used in civil engineering structural applications. Single lap bonded joints were produced with two commercial polymeric adhesives - epoxy (EP) and polyurethane (PUR) - and exposed to a mild (Mediterranean) range of thermal variations (-5 °C to 40 °C) for up to 350 cycles in a dry condition. The mechanical performance of the adhesively bonded joints was assessed by means of single lap shear tests. Regardless of the inherent differences between both adhesives, results obtained show that the global effect of thermal cycles on the load vs. displacement response of EP-GFRP and PUR-GFRP joints was similar. For both adhesives, thermal cycles caused considerable reduction of joint stiffness and strength, with maximum reductions of 18% and 22% for EP-GFRP joints, respectively, and 19% and 11% for PUR GFRP joints. The degradation of performance was influenced by post-curing effects, more relevant in the PUR adhesive. Before exposure to thermal cycles, both types of specimens exhibited similar failure mechanisms, which generally (80-90% of cases) involved light fibre tear and fibre tear modes, attesting the effectiveness of the adhesion process and material compatibility. Exposure to thermal cycles did not influence the failure modes of the PUR-GFRP joints; however, EP-GFRP joints became more prone to adhesive failure after being subjected to thermal cycles. Overall, the results obtained indicate that thermal cycles degrade bonded joints between pultruded GFRP adherends; however, for the conditions used in this study, this degradation seems to be compatible with the structural use of this type of joints in civil infrastructure.

This paper presents an experimental study about the effects of hygrothermal and outdoor ageing on a polyurethane (PUR) adhesive used in civil engineering applications. Small scale adhesive coupons were exposed to different types of ageing environments for up to two years: (i) immersion in demineralised water at 20 and 40 °C, (ii) immersion in salt water at 20 and 40 °C, (iii) continuous condensation environment at 40 °C, and (iv) outdoor ageing in Lisbon, Portugal. At predetermined times, after a desorption period until constant mass, the effects of such exposure on the physical and mechanical responses of the PUR adhesive was investigated using the following techniques: (i) water sorption, (ii) dynamic mechanical analyses (DMA); (iii) flexural; and (iv) in plane shear tests. The diffusion mechanisms observed were not purely Fickian; a long relaxation period was noticed, with water molecules being continuously incorporated in the adhesive until the end of the experiments; two alternative analytical modelling approaches were successfully used to simulate the diffusion processes. After immersion in water and salt water for two years, the viscoelastic behaviour of the adhesive showed signs of post-curing phenomena, and some of the physical degradation was found to be reversible due to drying, although it was not explicitly quantified; accordingly, the Tg showed increasing trends (11 14%). The mechanical properties of the adhesive showed signs of irreversible degradation mechanisms, more relevant on the in-plane shear properties, with reductions up to 26% in strength and 44% in modulus under the harsher conditions. Flexural properties also exhibited irreversible degradation, with maximum reductions up to 30% in strength and 36% in modulus. Increased temperature did not have a significant effect in the flexural and shear strength, but caused higher degradation in the corresponding moduli. The degradation caused by salt water immersion and continuous condensation was comparable to that in demineralized water immersion (at the same temperature).

This paper presents an experimental study about the durability of a cold curing structural epoxy (EP) adhesive exposed to different hygrothermal and outdoor ageing environments, typical of civil engineering applications, for up to two years: water and salt water immersion at 20 °C and 40 °C, continuous condensation at 40 °C, and outdoor ageing in a mild Mediterranean climate. After specific exposure periods, changes in the following physical properties and mechanical behaviour of the adhesive were assessed: (i) media diffusion, through water uptake (in hygrothermal environments); (ii) viscoelastic behaviour, through dynamic mechanical analyses (DMA); and (iii) flexural and (iv) in plane shear behaviour. Regarding media diffusion, water uptake did not follow a Fickian behaviour and a final saturation stage was not reached; two alternative non Fickian analytical models were successfully fitted to the test data and the corresponding diffusion parameters were determined. In what concerns the viscoelastic behaviour, while continuous condensation and outdoor ageing caused negligible changes, the Tg of the adhesive generally decreased due to immersion (around 20% in water and 10% in salt water after two years); in addition, at later stages of water immersion, the tan ? curve showed significant shape differences, with the usual curve peak being replaced by two different peaks; a generalised reduction of the storage modulus at the glassy plateau was also noted. In terms of mechanical performance, such plasticization effects were visible in the flexural and shear stress strain behaviours. The flexural properties exhibited irreversible degradation, with the highest reductions (two years of ageing in water at 40 °C) being about 24% and 30% in strength and modulus, respectively. Regarding the shear properties, in hygrothermal environments the shear modulus showed similar decreasing trends to the flexural modulus (43% reduction after one year), but the shear strength increased (~25%); the outdoor ageing affected the shear properties in the same way, but the magnitudes of the changes were lower.

N/A

Abstract A buried plastic pipe undergoes deformation, but it stabilizes at the end of a certain time not exceeding two years. Thus, there is an interest in determining the extrapolated creep of structured wall plastic pipes at 2 years. The main goal of this work is to present information regarding the assessment of results and their accuracy, based both on the requirements of the product standard [3] and on the uncertainty of the tests.

N/A

This paper presents a literature review and results of an experimental study about the effects of thermal cycles on the physical and mechanical properties of pultruded glass fibre reinforced polymer (GFRP) profiles used in civil engineering structural applications. The GFRP profiles used in this study present similar fibre architecture, differing only in their matrix nature: unsaturated polyester and vinylester. Small-scale coupons obtained from both types of GFRP profiles were exposed to a Mediterranean range of thermal variations (-5 °C to 40 °C) for up to 190 cycles in a dry condition. The effects of such exposure on the physical and mechanical response of the GFRP materials were assessed and compared using the following experimental techniques: (a) dynamic mechanical analyses (DMA) to assess the viscoelastic behaviour; (b) tensile, flexural and interlaminar shear tests, to evaluate the mechanical properties; and (c) scanning electron microscopy (SEM), to monitor the potential changes in the microstructure due to the degradation (if any) caused by the thermal cycles, as well as the possible changes into the main mechanisms of fracture. After exposure to thermal cycles, the viscoelastic behaviour of the GFRP profiles presented only slight changes, indicating no significant degradation, neither in the matrix structure nor at the fibre-matrix interphase. In terms of mechanical properties, both types of GFRP materials suffered slight changes regarding tensile and interlaminar shear properties. Flexural properties were more affected, particularly the flexural modulus, especially in the first cycles, as degradation tended to stabilize for increasing cycles. The GFRP profile made of vinylester resin presented better overall performance than the one made of polyester, especially regarding the tensile properties. SEM observations of the surfaces of fracture of mechanically tested pultruded specimens showed two main mechanisms of crack propagation: cohesive rupture (matrix cracking), where the crack propagates inside the matrix, and adhesive rupture (fibre-matrix debonding), where the crack propagates at the interface fibre-matrix. Degradation of the polyester matrix caused by the thermal cycles is evidenced by extensive matrix microcracking and increased fibre-matrix debonding. The vinylester matrix resists better to such degradation as fibre-matrix debonding occurs in less extent, and matrix microcracking is scarcely present.

This communication presents preliminary results of a research project on the effects of different environmental agents on the physical, chemical, aesthetical and mechanical properties of glass fibre reinforced polymer pultruded (GFRP) profiles made of either polyester or vinylester resin. In order to study the potential degradation of the two types of profiles in typical environments of civil engineering applications, test specimens are being subjected to the following exposure conditions: (i) immersion in demineralised water, at 23 ºC, 40 ºC and 60 ºC; (ii) immersion in salt-water, at the same temperatures; (iii) continuous condensation at 40 ºC; (iv) salt fog chamber; (v) thermal cycles, from -5ºC to 40ºC; (vi) accelerated weathering fluorescent ultraviolet light apparatus. Additionally, test specimens were placed in the roof of LNEC thereby being subjected to a natural degradation in a controlled environment. At predefined time intervals, batches of test specimens placed in the above mentioned exposure environments are being removed for physic-chemical and mechanical characterization, in order to assess their behaviour. / Nesta comunicação são apresentados os resultados preliminares de um projecto de investigação em que estão a ser avaliados os efeitos da degradação ambiental nas características físico-químicas de perfis pultrudidos de plástico reforçado com fibra de vidro com dois tipos de matriz – uma de poliéster e outra de viniléster. Com o objectivo de estudar os eventuais efeitos de degradação nos dois tipos de perfis, quando expostos a condições típicas das aplicações em engenharia civil, foram efectuadas as seguintes exposições em provetes retirados dos perfis: (i) imersão em água desmineralizada, a 23 ºC, 40 ºC e 60 ºC; (ii) imersão numa solução salina, às mesmas temperaturas; (iii) condensação em contínuo a 40 ºC; (iv) câmara de nevoeiro salino; (v) ciclos térmicos, entre -5 ºC e 40 ºC; (vi) envelhecimento artificial acelerado com lâmpadas fluorescentes de radiação ultravioleta. Para além disso, foram expostos provetes no telhado do edifício principal do LNEC, onde ficaram sujeitos a envelhecimento natural. Em intervalos predefinidos, foram efectuados ensaios de caracterização físico-química e mecânica dos materiais, para monitorizar o seu desempenho ao longo do tempo.

N/A

The main purpose of this paper is to present the results of a study intended to assess the durability of stabilized PVC-U for outdoor applications, in form of calendered films and extruded plates. The samples were subject to different ageing conditions and their degradation state were evaluated, using techniques of molecular analysis, namely Fourier transformed infrared spectroscopy (FTIR), as well techniques for evaluation of macroscopic properties, as colorimetry and tensiles tests. The development of formulations, the ageing and the subsequent characterisation were done in LNEC. Therefore, after a brief introduction, this paper presents the experimental part of the study, as regards the composition of samples and the experimental methods of deterioration and characterisation. Subsequently, the results of the study, their interpretation and the final conclusions are also presented.

The main purpose of this paper is to present the results of a study intended to assess the durability of stabilized PVC-U for outdoor applications, in form of calendered films and extruded plates. The samples were subject to different ageing conditions and their degradation state were evaluated, using techniques of molecular analysis, namely Fourier transformed infrared spectroscopy (FTIR), as well techniques for evaluation of macroscopic properties, as colorimetry and tensiles tests. The development of formulations, the ageing and the subsequent characterisation were done in LNEC. Therefore, after a brief introduction, this paper presents the experimental part of the study, as regards the composition of samples and the experimental methods of deterioration and characterisation. Subsequently, the results of the study, their interpretation and the final conclusions are also presented.

The outdoor degradation of poly(vinyl chloride) (PVC) products is complex and not completely understood for most of the technical formulations. Furthermore, it is known that the behaviour of such materials is dependent of the photo-oxidation conditions, namely source of radiation, temperature, presence of water and humidity. In the present work, we have used X-ray photoelectron spectroscopy (XPS) to evaluate the influence of different photo-oxidation conditions on the surface degradation of stabilized PVC, low thickness calendered samples (~ 150 ?m). The main objective is the study of the influence of the weathering conditions on the degradation level of stabilized PVC products for outdoor applications trying to go deeper in the understanding of the mechanism of both the degradation and the stabilization of the surface under different environmental conditions, different polymer formulations and different processing methods (extrusion or calendering). Comparisons are made with previous results obtained using colourimetry and infrared spectroscopy. The role of PVC formulation and of radiation source and water were studied using artificial weathering. Results were compared with degradation induced by natural weathering in Lisbon.

The main purpose of this paper is to present the results obtained, during the years 2001 and 2002, from a study developed in LNEC. The object of this study was to assess the synergetic effect of three of the most significant deteriorating climatic agents (radiation, temperature and water) on the evolution of the properties of hard PVC stabilised with titanium dioxide, for outdoor applications. For the purpose, several samples were subject to natural and artificial weathering. Moreover, their physical and mechanical properties were characterised by techniques of analysis and assessment of the surface aspect (colour and brightness), of assessment of the molecular properties by infrared microscopy (MICROFTIR), as well as of determination of the tensile mechanical properties and assessment of the Charpy impact resistance. The paper was both orally presented and by poster at the panel meeting “Ageing, Irradiation, Stabilisation” of the Congress MoDeSt 2002. Therefore, this publication includes the text of the paper, the poster, as well as the slides from the oral communication. The development of the formulations, the ageing and the subsequent characterisation by colorimetry, brightness, Charpy impact and tension, were done in LNEC. The characterisation by infrared microscopy was performed in the Laboratoire de Photochimie Moleculaire et Macromoleculaire of the University Blaise-Pascal, Clermont-Ferrand, France.

The main purpose of this paper is to present the results obtained, during the year 2003, from a study developed in LNEC. The object of this study was to assess the synergetic effect of two deteriorating climatic agents (radiation and water) on the evolution of the properties of extruded plates made of hard PVC stabilised with titanium dioxide, for outdoor applications. For the purpose, several samples were subject to natural and artificial weathering, their deterioration condition having been characterised by means of techniques of analysis of colorimetry and infrared spectroscopy (FTIR). Initially, only the presentation of a poster titled “Artificial and Natural Weathering of Polyvinyl chloride for Outdoor Applications: the Influence of the Radiation and Water on the Evolution of the PVC Properties” was scheduled. Nevertheless, upon request from the secretariat of the Congress, the author also presented an oral paper on the same subject, but including experimental results obtained during the year 2004, which were not mentioned in the poster. Similarly, these results, which were obtained by means of surface analysis techniques by Scanning Electron Microscopy (SEM) and by X photoelectron spectroscopy (XPS), were not included in the paper submitted to the Congress. Therefore, this publication includes the text of the paper referring to the poster, which was initially predicted, as well as the slides of the oral communication presented. It also contains a few results obtained in 2004. The development of the formulations, as well as the ageing and the subsequent characterisation by colorimetry, by infrared spectroscopy and by scanning electron microscopy were performed in LNEC. The characterisation by X photoelectron spectroscopy was conducted at the Molecular Chemistry-Physics Centre of the Instituto Superior Técnico (Higher Technical Institute).

The main purpose of this paper is to present the results of a study intended to assess the deterioration condition of extruded hard PVC plates, for outdoor applications. The plates were subject to different ageing conditions, using techniques of surface analysis, namely scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The development of formulations, the ageing and the subsequent characterisation by scanning electron microscopy were done in LNEC. The characterisation by X-ray photoelectron spectroscopy was done at the Centre for Molecular Chemistry-Physics of Instituto Superior Técnico (Higher Technical Institute of Lisbon). Therefore, after a brief introduction, this paper presents the experimental part of the study, as regards the composition of samples and the experimental methods of deterioration and characterisation. Subsequently, the results of the study, their interpretation and the final conclusions are also presented.

Procurou-se com a presente comunicação, apresentar uma metodologia de validação de um programa informático, desenvolvido no NMPC do LNEC especificamente para a calibração de um calorimetro diferencial de varrimento (DSC) e para calcular a incerteza associada à determinação da entalpia de fusão. Assim, após uma breve introdução, a presente comunicação expõe a formulação essencial que serviu de suporte ao desenvolvimento do programa informático referido, descreve os elementos que constituem o procedimento de validação do mesmo, apresenta o processo de estimativa da incerteza de medição e os resultados da análise efectuada.

O presente relatório (relatório 2) contém os resultados de um estudo desenvolvido no Núcleo de Materiais Orgânicos (NMO) inserido num projeto de Pós-Doutoramento com a duração de três anos e teve como objetivo a avaliação do melhoramento das propriedades fisicas e mecânicas de amostras de polietileno reciclado em misturas binárias com nanoargilas ligantes (nanoclays), para aplicação em tubagem na construção civil. Assim, após uma caracterização preliminar de reciclados de polietileno (relatório 1) e antes da análise do desempenho de tubagem incorporando material reciclado (relatório 3), realizou-se um estudo de otimização de formulações introduzindo materiais cerâmicos constituídos por silicatos e aluminatos (nanoargilas) com o objetivo de melhorar algumas propriedades térmicas e mecânicas da matéria-prima. Com diversas técnicas de análise, estando entre elas a calorimetria diferencial de varrimento, a análise mecânica-dinâmica e a termogravimetria, obtiveram-se resultados experimentais que foram analisados a nível estrutural.

O presente relatório, que é o último de uma série de 3, contém resultados de um estudo desenvolvido no Núcleo de Materiais Orgânicos (NMO) da instituição de acolhimento LNEC, inserido num projeto de Pós-Doutoramento, subsidiado pela FCT. O objetivo foi o de avaliar o desempenho e a degradação de tubos incorporando polietileno reciclado, proveniente da indústria portuguesa. Recorrendo à calorimetria diferencial de varrimento foram medidos o tempo e a temperatura de indução à oxidação de compostos granulados usados para o fabrico de tubos, bem como de amostras extraídas de tubos. Através de ensaios de resistência à pressão interior foram caracterizados tubos extrudidos laboratorialmente, utilizando amostras de PEADRepsol PE T1OONN e amostras recicladas, tal como suas misturas percentuais com masterbatch contendo nano argila e antioxidante.

Este relatório contém o conjunto de todas as normas EN e ISO referentes a sistemas de tubagem em material plástico, organizadas por aplicação, em vigor à data de Setembro de 2011.

Este relatório contém o conjunto de todas as normas EN e ISO referentes a sistemas de tubagem em material plástico, organizadas por aplicação, em vigor à data de Setembro de 2011.

N/A

No presente relatório apresentam-se os dados meteorológicos do ano de 2009, recolhidos na estação meteorológica existente no Núcleo de Materiais Orgânicos do Departamento de Materiais do LNEC, em Lisboa.

No presente relatório descrevem-se os procedimentos adoptados pelo LNEC no âmbito dos estudos para concessão de um Documento de Aplicação (DA) a revestimentos por pintura para protecção de betão, em condições de exposição atmosférica no exterior e sem influência de tráfego ou de acções químicas severas. Indicam-se também as acções a desenvolver periodicamente para comprovar que continuam reunidas as condições para a concessão do DA.

Procedeu-se à avaliação da resistência à alteração de cor de tintas de várias cores, por observação visual e medição das coordenadas cromáticas e da diferença de cor ao longo do tempo de exposição em condições de envelhecimento natural e artificial, a fim de estabelecer requisitos mínimos para revestimentos por pintura coloridas para paredes exteriores de edifícios. Neste relatório descreve-se o plano experimental adoptado, o trabalho desenvolvido, os resultados obtidos e uma possível metodologia para avaliar a resistência à alteração de cor em tintas para paredes exteriores.

O presente relatório apresenta os resultados e as conclusões mais relevantes do estudo experimental que foi realizado com o objectivo da caracterização de betumes modificados com polímero com vista ao seu enquadramento na Norma Europeia EN 14023 - Bitumen and bituminous binder - Framework specification for polymer bitumens.

O presente relatório contém o trabalho final do estágio profissionalizante efectuado no Departamento de Materiais do Laboratório Nacional de Engenharia Civil pela aluna da Licenciatura em Química Tecnológica da Faculdade de Ciências da Universidade de Lisboa, Ana Luísa Seara Pires. O trabalho, intitulado “Caracterização por análise térmica de adesivos estruturais usados na Engenharia Civil”, teve como objectivo principal contribuir para o conhecimento dos efeitos das condições de cura na temperatura de transição vítrea em três adesivos epoxídicos utilizados na colagem de materiais compósitos reforçados com fibras a estruturas de betão, no âmbito da sua reabilitação.

Os resultados experimentais, obtidos através da medição de propriedades dos materiais e produtos, requerem tratamento específico e adequado, de forma a garantir a sua qualidade. É por isso muitas vezes necessário recorrer a métodos estatísticos para fazer a análise do tipo de distribuição dos resultados, proceder à deteção de valores suspeitos num conjunto de observações e à eventual rejeição de resultados anómalos. Este tipo de tratamento estatístico é principalmente adequado a ensaios de intercomparação, quer do foro metrológico (comparação de valores de padrões ou materiais de referência, mediante medição efetuada por operadores de diferentes laboratórios metrológicos, com incerteza variável), quer do âmbito dos laboratórios de ensaio. Os ensaios de Comparação Interlaboratorial realizados por laboratórios de ensaio, constituem uma ferramenta de garantia da Qualidade e são utilizados para a validação de métodos de ensaio (incerteza e robustez) e como um meio para a determinação das características de desempenho dos laboratórios, nomeadamente da reprodutibilidade e da repetibilidade. Nesta publicação faz-se uma descrição dos vários parâmetros que devem ser determinados em ensaios interlaboratoriais do tipo “Intercomparações com valor de consenso” e respetivos métodos de cálculo. A estatística aqui apresentada pode, numa boa parte dos casos, ser também aplicada à análise de resultados de medições experimentais correntes.

The main purpose of this Paper is to present a state of the art about weathering and polymer degradation. This review was presented during a training course promoted by the 5th European Weathering Symposium EWS (XXVIIth Colloquium of Danubian Countries on Natural and Artificial Ageing of Polymers), which was held in Lisbon on September 21 - 23, 2011, organised on behalf of CEEES (Confederation of European Environmental Engineering Societies) by the German Management Society for Environmental Engineering GUS (Gesellschaft für Umweltsimulation e.V.) and supported by SOPSAR (Sociedade Portuguesa de Simulação Ambiental e de Avaliação de Riscos), APIP (Associação Portuguesa da Indústria de Plásticos) and LNEC (Laboratório Nacional de Engenharia Civil). The main topics of this review are the weathering of polymers and composites, the determination, simulation and effects of relevant climatic quantities, innovative polymer additives, new test procedures and devices, instrumental methods of analysis to evaluate polymer degradation, recent developments in polymeric materials and composites designed for outdoor applications and methods for service-life prediction.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A