Publications

Na sequência dos estragos causados pelo furacão Lorenzo no molhe principal do porto de Ponta Delgada, foi elaborado um projeto de reparação do mesmo, tendo havido necessidade derealização de ensaios em modelo físico tridimensional com o objetivo de avaliar a estabilidade da solução projetada.

Em 2 de outubro de 2019, o furacão Lorenzo atingiu as ilhas do Arquipélago dos Açores, provocando estragos nas infraestruturas portuárias, nomeadamente no molhe principal do porto de Ponta Delgada. No sentido de minorar este problema, foi elaborado um projeto de reparação do molhe (CONSULMAR, 2020), tendo nesse âmbito sido necessária a realização dos ensaios em modelo físico tridimensional com o objetivo de avaliar a estabilidade da solução projetada.Os ensaios foram realizados num tanque de ondas irregulares do LNEC à escala geométrica1:65 e contemplaram 6 séries de ensaios associados a 3 rumos de agitação marítima (WSW, S, SSW) e a dois níveis de maré (baixa-mar e preia-mar) associados a períodos de pico (Tp) entre 12 s e 20 s e alturas de onda significativa (Hs) variando entre 8 m e 15 m, Lemos et al. 2020.

A avaliação da estabilidade do manto resistente de quebra-mares de taludes requer, na maioria dos casos, a realização de ensaios em modelo físico. Entre os diferentes métodos de avaliação da evolução da estabilidade, destaca-se a medição do volume erodido do manto resistente por ação da agitação marítima. Este volume pode ser determinado a partir de levantamentos consecutivos da envolvente dos taludes. Melby[1] apresentou uma fórmula para previsão da evolução do dano em quebra-mares de taludes com base nas características da agitação neles incidente. No presente estudo pretendeu-se utilizar um programa de ensaiosem modelo físico bidimensional semelhante ao programa que conduziu à referida fórmula aplicado a um caso de estudo correspondente a uma secção do quebra-mar do porto de Peniche.Os ensaios realizados fazem parte do projeto BSafe4Sea que visa desenvolver, testar e comprovar o conceito de previsão do comportamento estrutural de quebra-mares de talude, que constitui a base de um sistema inovador de apoio à decisão. Os ensaios tiverem como objetivo analisar a resposta da estrutura a diferentes estados de agitação incidentes, cujos resultados são fundamentais para o desenvolvimento d e formulações empíricas de previsão da evolução do dano.

This paper studies the effects of an air bubble curtain on surface water waves. Water particle velocities and free surface elevations were measured simultaneously at two cross-shore sections downstream the air bubble curtain. Measurements were carried out for regular waves regarding different air bubble curtain configurations. Free surface elevations were measured using resistive gauges and the instantaneous velocities were acquired using an Acoustic Doppler Velocimeter (ADV). The characteristics of the free surface elevation, velocity field and turbulence are analyzed and discussed. The free surface elevation was found to be constantly attenuated by the air bubble curtain. The phase-averaged velocity profiles also depict the effect of the air bubbles in the flow field by generating milder longitudinal velocities (u) and by increasing the transverse component of the velocity (w). The increase in the turbulence intensity and the different energy spectrum produced by the air bubble curtain is also analyzed. The experimental results indicate that the thickness of the air bubble curtain and the total air flow rate affects the wave field.

An experimental study was carried out to investigate seabed-pipeline interactions with regard to soil liquefaction. For a soil with a high proportion (30 to 60%) of fine sediment, four groups of tests were configured to reproduce soil liquefaction around pipelines for different initial pipe depths, pipe densities and wave conditions (wave height and period). The study focused on verifying the theoretically computed areas of soil failure by analyzing the sinking depths of the pipelines. The main findings are that a pipe with a submerged specific weight of less than half that of the soil will move up to the mudline; that the loss of soil loading capacity is more frequently evidenced in a fluid-like behavior of the soil than by an abrupt breaking of the soil matrix; and that the pipes which are totally buried will sink more than half-buried pipes. Moreover, wave action and the specific weight of the pipes seem to play more important roles in the expected behavior of the wave

In coastal areas, overtopping events and coastal floods, resulting from the occurrence of maritime storms, can cause severe damage to infrastructure, building and equipment, can be responsible for coastal morphology changes (coastal erosion), as well as put in damage human lives, animals or the ecosystem.

SAFEPORT safety system aims to daily reports to Sines harbour administration, potencial emergency situations regarding ships operation in port areas caused by extreme weather-oceanographic conditions, that may occur in the next three. It consists of a set of numerical models and a qualitative risk assessment and forecasting. It uses forecasts provided offshore of the area under study of sea agitation, wind and tide. The characterization of the response of the free and moored ships at a berth is performed using the numerical modelswhich deals with formulations in the frequency and time domain. The system issue alerts, through danger levels associated with risk levels of exceedance of recommended values for movements and forces imposed on ship mooring systems. SAFEPORT can be adapted to any port. So far, it has been developed and adapted to three terminals of the port of Sines, where three different ships were simulated. This paper presents the developments made to date of the safety system, in terms of its implementation and validation. The numerical models run every day, in real-time mode, in a computer cluster and the system provide forecast results for the next 72 hours. The results are disseminated on a web page and a mobile application in a variety of formats.

Early warning systems are an important tool for local authorities to detect emergency situations in advance and initiate the necessary safety measure. The To-SEAlert project has the aim of increasing the efficiency, robustness and reliability of the HIDRALERTA coastal hazards early warning system. This study shows a first intent to implement the SWASH numerical model to simulate wave overtopping for the Ericeira prototype. SWASH was implemented for one breakwater profile where overtopping discharge and associated risk levelsare estimated. It was compared to the current approach used in HIDRALERTA, the neuronal network NN_OVERTOPPING2. Finally, both approaches were compared with previously analysed video images of the site. The results showed that SWASH generally overestimates overtopping and is not in good agreement with the NN_OVERTOPPING2 or the video images. A possible reason might be the wave direction, which cannot be included in one-dimensional simulations in SWASH.

No âmbito do

Extending for more 900 km with diverse geomorphologies and land-use occupation, the Portuguese coastal zone is highly vulnerable to overtopping and flooding.

Com vista a otimizar a geometria do prolongamento do quebra-mar exterior do Porto de Leixões, bem como avaliar os impactes desse prolongamento nas condições de agitação na praia de Matosinhos, efetuou-se a caraterização da agitação marítima na zona de estudo, considerando várias soluções alternativas para o quebra-mar. A presente comunicação descreve os estudos realizados em modelo numérico para: a) o estabelecimento de regimes de agitação no exterior do porto, b) a caracterização da agitação e ressonância no interior do porto; c) a avaliação dos impactes do prolongamento do quebra-mar nas condições de agitação da praia de Matosinhos.

No âmbito do projeto HYDRALAB+ (H2020-INFRAIA-2014-2015), foi realizado no LNEC um conjunto de ensaios em modelo físico bidimensional (2D) de um perfil de um quebra-mar de talude em enrocamento, construído à escala geométrica 1:30, para diferentes condições de agitação marítima e níveis de maré correspondentes a cenários de alterações climáticas. Estas experiências tinham como objetivo analisar o dano, o espraiamento e o galgamento, nesses cenários.Em paralelo, na Faculdade de Engenharia da Universidade do Porto (FEUP), e em colaboração com Deltares, NL, foram realizados testes com a mesma configuração do quebra-mar, mas utilizando um modelo físico tridimensional (3D), à escala geométrica 1:35. Os resultados obtidos permitiram analisar a evolução do dano no manto resistente do quebra-mar (talude anterior, talude posterior e cabeça), assim como o galgamento, para condições de teste com e sem sobrelevação do nível médio da água do mar, considerando ou não a reconstrução do talude do quebramar entre testes consecutivos de uma mesma série de testes. Foram também realizados testes com ondas multidirecionais.O presente trabalho incide sobre a análise da evolução do dano para as diferentes sequências de tempestade em cenários de alterações climáticas. O dano é avaliado com base no tradicional método de contagem de blocos removidos e ainda com base no parâmetro adimensional do dano, S recorrendo a técnicas estereofotogramétricas.Em termos gerais, concluiu-se que o dano era mais elevado na proximidade do nível de repouso da água e que aumentava com a altura de onda significativa. Os danos foram, em geral, menores nos testes com ondas multidirecionais. Observaram-se, ainda, diferenças significativas entre os testes com danos cumulativos e com reconstrução do quebra-mar após cada teste. Nos ensaios realizados no LNEC com aumento do nível médio do mar e alternância entre dois níveis de maré, verificou-se um ligeiro aumento do dano devido ao aumento faixa onde ocorre erosão do perfil.

This paper presents a series of tests on a reduced physical model to reproduce the behavior of a moored oil tanker. The measurement techniques used and all the instrumentation are presented. Data analysis techniques are also presented. The objective of the tests is the characterization of the incident marine agitation and the response of the ship, including the movements according to 6 degrees of freedom and the forces in the mooring system.The tests were carried out in one of the tanks of the Marine Hydraulic Pavilion of the National Laboratory of Civil Engineering, using for the generation of marine agitation a batter capable of generating irregular waves.The vessel used is a scale model of the "Esso Osaka" tanker with a length of 3.43 m, a width of 0.53 m and a maximum draft of 0.23 m and is lying in terminal A of the Port of Leixões. The entire port area was built at 1:80 scale, including bathymetry and port structures. The waves are generated outside the port to the bathymetric of -20m ZHL (zero hydrographic of Leixões). Several sea states were simulated with irregular waves with periods between 10s and 16s and significant wave heights between 2m and 6m.The vessel is instrumented with an optical motion capture system according to the six degrees of freedom, composed of 4 cameras of high resolution that allows to follow the position of several targets placed in the ship and 6 load cells to measure the forces in the moorings and defenses. The measurement of free surface elevation was performed with a set of resistive probes and an ADV.

O sistema de proteção costeira da Cova-Gala, a sul da Figueira da Foz, inclui defesas longitudinais aderentes datadas de 1975 que têm como objetivo proteger a povoação da ação do mar. Ao longo dos anos têm-se registado eventos de galgamento destas obras que colocam em risco pessoas e bens. Face a uma possível subida do nível do mar na costa oeste portuguesa, é importante analisar a sua influência no agravamento do galgamento destas estruturas. Para tal, calculou-se o galgamento com a fórmula de Mase et al. (2013) utilizando as condições de agitação ao largo e níveis de mar obtidas de modelos de hindcast. Calculou-se ainda o caudal galgado para as mesmas condições de agitação e diferentes projeções de subida do nível do mar. A comparação de resultados permitiu concluir sobre o efeito da subida do nível do mar no galgamento para os valores considerados.

Usually, physical model tests support the design of breakwaters considering different incident wave conditions, including extreme events. This paper describes two-dimensional physical model tests of a rock armour breakwater, performed at LNEC´s experimental facilities, under the framework of the HYDRALAB+ project. The goal of the present work is to evaluate damage evolution under wave conditions resulting from future climate change scenarios. Test results are presented in terms of the non-dimensional damage parameter (S) and of the percentage of displaced armour units (D). The data analysis is focused on the cumulative damage progression related with wave parameters as Hmax and H2%, for the imposed storm sequences. The use of the stability number (Ns), considering both H=Hs and H=H2% revealed a good agreement in order to characterize its relationship with damage evolution. On the other hand, the use of Hmax revealed a decrease of the linearity on damage evolution.

Usually, physical model tests support the design of breakwaters considering different incident wave conditions, including extreme events. This paper describes two-dimensional physical model tests of a rock armour breakwater, performed at LNEC´s experimental facilities, under the framework of the HYDRALAB+ project. The goal of the present work is to evaluate damage evolution under wave conditions resulting from future climate change scenarios. Test results are presented in terms of the non-dimensional damage parameter (S) and of the percentage of displaced armour units (D). The data analysis is focused on the cumulative damage progression related with wave parameters as Hmax and H2%, for the imposed storm sequences. The use of the stability number (Ns), considering both H=Hs and H=H2% revealed a good agreement in order to characterize its relationship with damage evolution. On the other hand, the use of Hmax revealed a decrease of the linearity on damage evolution.

Nesta comunicação descreve-se a análise bidimensional (2D) em modelo físico do espraiamento e galgamento de um quebra-mar de talude, em cenários de alterações climáticas, realizado no âmbito do projeto HYDRALAB+ (H2020-INFRAIA-2014-2015). Com efeito, a subida do nível médio do mar, bem como o aumento da intensidade e frequência de temporais, previsível em tais cenários, pode dar origem a fenómenos de espraiamento e galgamento das estruturas de proteção costeiras e portuárias, cada vez mais intensos e frequentes, tornando as estruturas mais vulneráveis, bem como as zonas por elas protegidas.Assim, num canal de ondas irregulares do LNEC, foi construído um perfil de um quebra-mar de enrocamento, à escala 1:30, e definido um programa de 15 ensaios, considerando valores de altura de onda significativa, período de pico e níveis de água representativos de condições de agitação incidente extremas, a que se poderão associar os referidos cenários de alterações climáticas.Para cada ensaio, efetuaram-se medições da elevação da superfície livre, do espraiamento e do caudal médio galgado. Os valores experimentais de espraiamento e de galgamento foram comparados com os previstos pelas formulações empíricas do EurOtop, para um dos cenários de alterações climáticas testado.

This paper describes a programme under the responsibility of LNEC for the systematic observation and monitoring of maritime works, termed OSOM+, that has successfully been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad.The OSOM+ programme comprises the following four main components for each structure: Periodic visual inspections by a trained technician; Periodic aerial inspections with a UAV/drone; The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; A mobile, portable, application, for real-time input and visualization of the database information.This recently updated methodology encompasses a number of tools and functionalities that are illustrated in this paper with applications to a real case scenario, the Ericeira

This paper describes the physical model, experimental setup and tests performed at the Portuguese Civil Engineering Laboratory (LNEC), to study the motions and forces of a moored ship at the Leixões port, for different sea states in irregular waves. The tests were carried out at one of the wave tanks of LNEC, where the Leixões port layout was implemented at scale 1:80 with the detailed model similar to the prototype bathymetry and surrounding structures. The moored ship is a 3.43 m long scale model of the well-known

Scour protections are commonly designed according to semi-empiric methodologies, which are based on a deterministic approach. This often results in overestimated dimensions of the protection, namely, regarding the required minimum stone size for offshore engineering. Therefore, excessive costs of the protection are expected, when the deterministic design methodology is used. Moreover, these methodologies do not provide a measure of safety associated to the design of the scour protection. In this paper, one uses copulas theory to model the correlated long-term behaviour of the significant wave height and peak period. The statistical models are then used to address the probability of failure of a case study scour protection. The results show that the copula models influence the safety assessment of the scour protection. The research also includes a brief analysis of physical model tests, which were successfully used to define dynamically and statically stable scour protections for the case study analysed.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A