Publications

The availability of clean energy of wind waves is enough to meet current demand of the world, attracting researches to find devices with good performance to extract this type of energy. The oscillating water column converter is a type of device that has been extensively studied for this purpose. This paper describes a numerical analysis of an onshore oscillating water column device taking into account hydrodynamic and aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The numerical analyses are carried out by the Fluinco model, based on slightly compressible flow method to solve the Navier-Stokes equations, and employing the two-step semi-implicit Taylor-Galerkin method. The aerodynamic model is based on the first law of thermodynamics applied to the air column inside the chamber and on turbines similar to Pico

O conhecimento dos esforços resultantes da interacção de uma onda com um quebra-mar verticaltorna-se essencial no dimensionamento deste tipo de estruturas. No presente trabalho, o modelo numérico SPHyCE, baseado numa metodologia de tipo SPH - Smoothed Particle Hydrodynamics, é utilizado para o cálculo das forças num quebra-mar vertical. Para analisar a evolução das forças de impacto foram consideradas várias condições de profundidade no pé da estrutura e de altura de onda incidente abrangendo diferentes regimes de forças. A comparação dos resultados do modelo numérico com os das formulações empíricas permitiu verificar que as forças previstas são semelhantes para os casos de regime de onda parcialmente estacionária. No entanto, para o regime de forças de impacto, existem diferenças que se devem a diversos factores: i) a rebentação da onda no modelo SPHyCE pode não corresponder necessariamente à forma de rebentação prevista nas formulações empíricas; ii) no caso da rebentação com aprisionamento de ar, cuja influência no valor das forças é relevante, o modelo numérico atinge o seu limite de aplicação, pois não integra o ar e não existem formulações aplicáveis; iii) as formulações empíricas aplicáveis com rebentação dão valores claramente por excesso.

Tanto el perfil como la forma en planta de las playas fluviales vienen establecidos por numerosos factoresentre los que cabría destacar las características del sedimento y la dirección y módulo de la velocidad de la corriente en el río. Sin embargo, en ciertos casos, lejos incluso de su estuario o desembocadura, esta morfología puede estar determinada principalmente por la incidencia del oleaje pese a no tratarse de un entorno marítimo.Se presenta aquí una metodología cualitativa que nos permitirá reconocer los aspectos que influyen en la existencia de este tipo de morfologías. Para ello, se estudiará un caso particular, el de la playa de La Concordia ubicada en la margen izquierda del río Uruguay a 70 km de su desembocadura en el estuario del Rio de la Plata. Asimismo se analizará la forma en planta y se verificará que la misma está determinada por la acción del oleaje.

Three submerged coastal structures on the sandy seabed at SantaMaria delMar (SMM) Beach in Southwest Spain were monitored during the sixmonths after installation, starting inNovember of 2005. The monitoring evaluated the self-burial phenomenon of the 40 precast modular concrete elements of the three structures. Assessment included scouring around the structures, their vertical movement, the sinking velocity of the modules and the resulting beach profiles. Pressure sensors and precision topographies permitted continuous monitoring of the self-burial process for the first time in a full-scale case. Comparison of two bathymetries (one performed immediately prior to installation and another performed six months after installation) indicated slight accretion of the seabed,whereas intermediate topographic surveys indicated extensive scouring around the structures. The three structures began sinking into the sandy bottomplatform immediately after placement and continued until they reached the rocky bottom. This study implemented a new methodology using pressure sensors attached to the concrete modules to monitor the structural sinking. Unexpectedly, the average sinking speed was extremely rapid at approximately 3

The effects ofwave steepness andwave breaking on the stability of wave-dissipating blocks placed on caisson breakwaters are examined by hydraulic experiments under conditions with and without wave breaking. It is confirmed that there is a clear dependence of the block stability on the wave steepness through the wave-breaking type, such as plunging and spilling breakers. The stability parameter in thespilling breaker case is larger than that in the plunging breaker case. For non-breaking wave conditions, there is no effect of the wave steepness. An empirical stability formula is proposed taking into account the effects of the wave steepness and the wave-breaking type. Finally, by using the stability formula, failure probabilities of the wave-dissipating blocks having a nominal diameter are evaluated by the first-orderreliability method of the Level II reliability analysis.

This paper describes recent advances on maritime structures

This paper presents the numerical simulations done by using the waves2Foam, an OpenFOAM® library, to simulate the propagation of regular waves without breaking in a three-dimensional flume. The numerical code solves the unsteady Navier-Stokes equations and uses a Volume-of-Fluid (VoF) method to identify the free surface. A regular incident wave with a 1.5s period and 0.1m wave height, was considered. This is one of the conditions from the wide range of wave flume tests conducted at the National Laboratory for Civil Engineering (LNEC) whose objective was to analyze the hydrodynamics of wave transformation and wave breaking for different incident conditions over a variable bathymetry. Comparisons are made between the numerical and the experimental results. These comparisons include time-series of wave-gauges records at several locations along the flume and the corresponding amplitude spectra; significant wave height and average period evolution along the flume; time-series of the velocity components at one section of the flume, measured at the middle of the water column; and hodograph representation of the velocity components, in the middle of the water column, in the xy, xz, and yz planes along the flume. It was found that the numerical results obtained are close to the experimental data. The observed differences are attributable to numerical inaccuracies as well as the differences between the wave generation method in the numerical and experimental tests.

Neste artigo, apresenta-se uma breve descrição do papel da modelação física no apoio ao projeto de obras marítimas, seguida de um exemplo de ensaios realizados no âmbito da ampliação do porto de pesca de Rabo de Peixe, São Miguel

Descrevem-se os procedimentos para avaliar o caudal médio galgado sobre um trecho de um quebra-mar de taludesa partir das caraterísticas da agitação marítima incidente no mesmo trecho. Apresenta-se uma metodologia paraestimação de valores extremos daquele caudal, partindo das séries temporais da mesma variável, e ilustram-se essesprocedimentos num trecho do molhe oeste do porto de Sines que protege o posto 2 do terminal de granéis líquidos daação da agitação marítima. Este regime de extremos do caudal médio galgado é fundamental para a avaliação do riscode ocorrência de galgamentos não admissíveis no posto 2.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A