Publications

Knowledge of forces due to the action of waves on submarine outfalls composed by a pipe and stabilizing concrete weights, considering the wave propagation direction to the outfalls, is essential to their design. 3D numerical models based on RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid) are able to estimate forces on the pipe and weights. The present study aims to simulate a submarine outfall with stabilizing concrete weights at 1:15 scale which was previously tested in the 3D Shallow Water Basin at the Danish Hydraulics Institute (DHI) to analyse the influence of the direction of the incident wave and the distance from the pipe to the bottom on the outfall forces. In this study, numerical results are compared with experimental ones for waves with four different amplitudes and with wave incidence perpendicular to the outfall. The use of k-

The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.

Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.

This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira

This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.

This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.

Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula

This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the

Nesta comunicação, descrevem-se os mais recentes desenvolvimentos no LNEC em termos de instalações experimentais, técnicas de construção, equipamentos e metodologias utilizadas nos ensaios em modelo físico, com a apresentação de casos de estudos realizados para as zonas portuárias de Peniche Ponta Delgada, Leixões

Within the BlueSafePort project, an early warning system (EWS) for moored ships in the port of Sines as developed. In order to improve the reliability and accuracy of the system, two neural networks (NN) were trained,using wave buoys measured datasets. Numerical models results for the wave propagation are djusted and forecasts are improved.The trained neural networks were able to produce more accurate stimates for the significant wave height and mean wave period, at the buoy location, deployed in front of the ines Port. The use of the new NN led to an overall reduction of the root mean square error of around 80% compared with SWAN numerical model simulations, thus reducing potential errors in subsequential alculations and alert levels issued by the system for the moored ships.

Within the LIFE Garachico project, an HIDRALERTA EWS is being extended to include methodologies for creating an effective flexible adaptation strategic framework for coastal area of Praia da Vitória. This strategic framework is based on the definition of acceptable risk levels and specific interventions at the local level, allowing to increase the resilience of coastal urban areas against extreme coastal events (both present and future) consequences of climate change.

Esta comunicação descreve os ensaios de pressões efetuados para a caraterização das pressões máximas exercidas nos pilares de secção circular da ponte que liga o porto de Dakhla à costa bem como dos perfis verticais de pressões associadas.

Nesta comunicação são descritos os desenvolvimentos iniciais dos sub-casos do projeto C2IMPRESS referentes aos portos de Aveiro e da Figueira da Foz. A fase inicial envolveu a estimativa preliminar do galgamento induzido pelas ondas em alguns perfis das estruturas dos dois portos, assim como um primeiro inquérito sobre risco aos utilizadores desses dois portos.

Esta comunicação descreve os estudos em modelo reduzido tridimensional de estabilidade hidráulica e de galgamentos para o prolongamento do molhe leste correspondente à 3ª Fase de Expansão do Terminal XXI, do Porto de Sines.

Neste trabalho apresenta-se uma metodologia para determinar as condições de segurança e acessibilidade de navios ao longo do trajeto de acesso ao porto, ilustrando-se a sua aplicação nos casos de estudo dos portos de Sines. este trabalho insere-se no âmbito do desenvolvimento de novos sistemas de previsão e alerta para a navegação nos portos de Sines e Aveiro.

O litoral português apresenta um valor natural, económico e cultural único e de importância amplamente reconhecida. O dinamismo costeiro pode levar à ocorrência de galgamentos de estruturas de proteção costeira em situações de temporal, que podem causar inúmeros danos, podendo mesmo resultar na perda de vidas humanas ou na destruição de estruturas próximas da linha de costa. Deste modo, a gestão das zonas costeiras próximas de aglomerados populacionais deve considerar a implementação de medidas sustentáveis que mitiguem os fenómenos que afetam o litoral de forma mais gravosa, de que são exemplo a implementação de estruturas de proteção costeira.

No âmbito do projeto BlueSafePort está a ser desenvolvido um sistema para prever e alertar situações de emergência causadas pela agitação marítima, relacionadas com a navegação em portos, bem como constrangimentos operacionais. A paralisação dos terminais portuários leva a grandes perdas económicas e afeta em grande parte a competitividade geral do porto. Assim, o objetivo deste sistema é reduzir a vulnerabilidade do porto aumentando a sua capacidade de planeamento e resposta e

Physical modelling is one of the tools to help characterize wave runup and overtopping in maritime structures. Usually, the determination of wave runup is made by using resistive wave gauges along the breakwater slope while the evaluation of overtopping volumes (individual or total) is made by weighing the water overtopped with a scale that is collected in a reservoir installed on this scale.Nowadays, non-intrusive methodologies for the assessment of those parameters are being used, due to their simplicity and low cost. Video cameras, constitute a good alternative to old methods; however, their performance depends essentially on the post-processing methodologies used.The present paper presents the application of the Timestack methodology done so far, in the evaluation of: wave runup in 2D and 3D physical tests. The video-derived statistical parameters of wave runup (Rumax, Rumin, Rumed e Ru2%) are compared with the corresponded ones obtained with resistive wave gauges. The total water volume and the average overtopping flow rate from video data is compared with the one collected by a reservoir. Those cases will illustrate the advantages and drawbacks associated with Timestack methodology.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A