Papers
Info
Analysis of forces on a submarine outfall by a RANS-VoF numerical wave tank
Knowledge of forces due to the action of waves on submarine outfalls composed by a pipe and stabilizing concrete weights, considering the wave propagation direction to the outfalls, is essential to their design. 3D numerical models based on RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid) are able to estimate forces on the pipe and weights. The present study aims to simulate a submarine outfall with stabilizing concrete weights at 1:15 scale which was previously tested in the 3D Shallow Water Basin at the Danish Hydraulics Institute (DHI) to analyse the influence of the direction of the incident wave and the distance from the pipe to the bottom on the outfall forces. In this study, numerical results are compared with experimental ones for waves with four different amplitudes and with wave incidence perpendicular to the outfall. The use of k-
Year: 2019
Number Pages:
50-59pp.
Author(s): Didier, E.; Neves, M. G.; Teixeira, P.
: Defect and Diffusion Forum
Editor: Trans Tech Publications Ltd, Switzerland
Volume:
Vol. 396.
Keywords: Numerical wave tank; RANS-VoF; Forces; Submarine outfalls
Info
Damage progression in rubble-mound breakwaters scale model tests, under a climate change storm sequence
This paper describes the two-dimensional (2D) physical model tests of a rock armor breakwater, performed at LNEC´s experimental facilities, under the framework of the HYDRALAB+ project. The aim of the present work was to evaluate damage evolution under future climate change scenarios, by using different damage evaluation techniques. The tested wave conditions simulated a storm sequence where two water levels (low water and high water) were considered, as well as an increase of the wave height. The water levels and the wave heights were chosen to simulate extreme events forecasted on climate change scenarios. Damage evaluation was based on the traditional counting method and on stereo-photogrammetric techniques. Test results are presented in terms of the damage parameter S and in terms of the percentage of removed armor units. The analysis is focused on the damage progression during the scale model tests, for the imposed storm sequence. The damage presents an oscillating behavior with two main damage areas corresponding to the active zones for each level, due to the variation of the water level between low-water and high-water. This behavior differs significantly from that found for the common storm sequences usually tested, where the water level does not change. Both measuring techniques lead to an intermediate damage of the cross-section breakwater. However, the damage parameter assessment with the stereo-photogrammetric technique allows a more versatile evaluation, since it is possible to characterize damage in representative zones of the cross-section
Year: 2019
Author(s): Fortes, C. J. E. M.; Lemos, R.; Mendonça, A. C.; Reis, M. T. L. G. V.
: Journal of Research on Engineering Structures and Materials (RESM)
Editor: MIM Research Group
Volume:
Vol. 5 Iss. 4.
Keywords: Stereo-photogrammetric techniques; Climate change; Rubble-mound breakwaters; Damage progression
Info
Experimental investigation on the power capture of an oscillating wave surge converter in unidirectional waves
The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.
Year: 2019
Number Pages:
975-992pp.
Author(s): Brito, M.; Ferreira, R. L.; Teixeira, L; Neves, M. G.; R. Canelas
: Renewable Energy
Editor: Elsevier
Volume:
Volume 151.
Keywords: Power take-off: PTO damping; Response amplitude operator: RAO; Capture width ratio: CWR; Oscillating wave surge converter: OWSC; Wave energy
Info
Measuring wave run-up, overtopping and damage of rubble-mound breakwaters in scale model tests
A set of scale-model tests was carried out at the wave basin of the Leibniz University Hannover to extend the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater
Year: 2019
Number Pages:
118-129pp.
Author(s): Santos, J. A.; Lemos, R.; Weimper, J.; Gronz, O.; Hofland, B.; Sande, J.; Pinheiro, L.; Spans, J.H.; Peña, E.; Reis, M. T. L. G. V.; Fortes, C. J. E. M.; Figuero, A.; Laiño, E.; Bornschein, A.; Kerpen
Editor: Hydralab+
Keywords: Rubble-mound breakwaters; Model tests; Overtopping; Wave run-up
Info
Numerical analysis of the interference between two elastically mounted cylinders in tandem subject to flows at low Reynolds numbers
Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.
Year: 2019
Number Pages:
11p.
Author(s): Teixeira, P.; Rechsteiner, P.; Didier, E.
: Journal of the Brazilian Society of Mechanical Sciences and Engineering
Editor: Springer
Volume:
Vol. 41.
Keywords: Finite element method; Vortex-induced vibration; Wake interference; Tandem arrangement; Circular cylinders
Info
Observação e monitorização de obras marítimas com a nova metodologia OSOM+
This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira
Year: 2019
Number Pages:
22p.
Author(s): Fortes, C. J. E. M.; Capitão, R.; Henriques, M. J.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Silva, L. G.
: Revista Mundi, Engenharia, Tecnologia e Gestão
Editor: Instituto Federal do Paraná
Volume:
v.4, n.2.
Keywords: Ericeira
Info
A methodology to determine the optimal size of a wells turbine in an oscillating water column device by using coupled hydro-aerodynamic models
This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.
Year: 2018
Number Pages:
9-18pp.
Author(s): Torres, F.; Teixeira, P.; Didier, E.
: Revista Renewable Energy
Editor: Elsevier
Volume:
Vol. 121.
Keywords: Air pressure control; Turbine sizing; Oscillating water column; Wave energy
Info
An integrated tool for modelling oscillating water column (OWC) wave energy converters (WEC) in vertical breakwaters
This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.
Year: 2018
Number Pages:
198
Author(s): Mendonça, A. C.; Dias, J.; Didier, E.; Fortes, C. J. E. M.; Neves, M. G.; Reis, M. T. L. G. V.; Conde, J. M.; Poseiro, P.; Teixeira, P. R. F.
: Journal of Hydro-environment Research
Editor: Elsevier
Volume:
Vol. 19.
Keywords: Wave power; SWAN-URANS models; Nonlinear numerical modelling; Physical modelling; Wave-structure interaction; Oscillating water column (OWC) wave energy converter (WEC)
Info
Asymmetric copula
Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula
Year: 2018
Number Pages:
304-334pp.
Author(s): Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Vanem, E.; Reis, M. T. L. G. V.; Neves, L.
: Wind Engineering
Editor: Sage
Volume:
Vol. 42, No. 4.
Keywords: Asymmetry; Crámer
Info
Characterization of ship motions induced by wake waves
This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the
Year: 2018
Number Pages:
547-555pp.
Author(s): Pedro, F.; Pinheiro, L.; Fortes, C. J. E. M.; Santos, J. A.; Hinostroza , M.
: Progress in Maritime Technology and Engineering
Editor: Taylor & Francis
Keywords: Wake waves; SWAMS; Ship motions
|
Comunicação
Info
Experimental study of forces on a submarine outfall: influence of incident wave direction of stabilizing concrete weights and pipe distance from the bottom
In order to provide new insight into the flow and forces around a submarine outfall, 3D testswere performed in the DHI Shallow Water Basin with different outfall geometries (with andwithout stabilizing concrete weights), different wave obliquities (90º, 30º and 10º) anddifferent pipe distances from the bottom. The tests were carried out in the subcritical flowregime. The collected data provide new understanding of the importance of the wave obliquityin the forces on the outfall, especially for small values, where there are no available data.Moreover, for the case with the pipe stabilized by concrete weights, where almost noinformation is available, the influence on the forces of the wave obliquity and of the pipedistance from the bottom are analyzed, giving important indications to the design project.
Year: 2014
Number Pages:
8p.
Author(s): Neves, M. G.; Mendonça, A. C.; Didier, E.; Reis, M. T.; Inverno, J.; Figueira, P.; Afonso, C.; Vílchez, M.; Clavero, M.; Ortega-Sánchez, M.; Losada, M. A.
Info
Experimental study of stability of submarine outfalls in muddy soils
Marine structures built on muddy soils, such as breakwaters and submarine outfalls, are subject to settlement, scour and liquefaction and the mechanics of these processes are still uncertain. The aim of the present experimental study is to investigate stability of submarine outfalls in low quality soil. Physical modeling, carried out in the wave flume at UNAM, Mexico, is described and the results are presented and discussed. Tests were performed for different wave conditions (wave heights and periods), different soil characteristics (several mixtures of kaolinite and sand) and three structural layouts: the pipe resting on the soil, the pipe partially buried and a totally buried pipe.The pore pressure for different positions on the soil and the movements of the pipes were measured, together with surface elevation along the flume.
Year: 2014
Number Pages:
16p.
Author(s): Mendoza, E.; Neves, M. G.; Afonso, C.; Casarín, R.S.; Reis, M. T.; Clavero, M.; Losada, M. A.
Keywords: Waves; Liquefaction; Physical model; Submarine outfalls; Low quality soil
Info
Experimental wave breaking velocity characterization for monochromatic, bichromatic and irregular waves
The present work focuses on the comparison between different types of data analysis (time analysis; Fourier transform spectral analysis; wavelet transform spectral analysis; and hodograph representation) applied to Acoustic Doppler Velocimetry (ADV) records of wave orbital velocities. Different wave conditions (monochromatic, bichromatic and irregular) have been tested, for the general purpose of experimentally investigating wave shoaling and breaking over a gentle slope. The analysis of the velocity data, through these methodologies, illustrates other relevant phenomena occurring in the wave propagation, which cannot be depicted by the usual wave gauges. Each of these techniques has advantages and drawbacks,and so they should be complementary.
Year: 2014
Number Pages:
87-96pp.
Author(s): Conde, J. M.; Neves, C. F.; Fortes, C. J. E. M.; Lemos, R.
Keywords: Irregular waves; Bichromatic waves; Regular waves; Wave breaking; Acoustic doppler velocimetry
Info
Galgamento do quebra-mar poente de Albufeira: Comparação entre o modelo numérico SPH e medições de campo
Os modelos SPH (Smoothed Particle Hydrodynamics), baseados na formulação Lagrangiana dasequações da Dinâmica dos Fluidos, são uma opção atractiva para modelar escoamentos com superfície livre, poisnão necessitam de malha computacional, permitindo modelar fenómenos complexos, como a rebentação de ondase o galgamento. Neste trabalho apresenta-se o modelo numérico SPHyCE em desenvolvimento no LNEC e a suaaplicação à determinação do galgamento no quebra-mar poente do Porto de Pesca de Albufeira (Algarve), no qualforam realizadas as primeiras campanhas de medição de galgamento num quebra-mar em Portugal no âmbito doprojecto SPACE (Desenvolvimento e validação de um modelo SPH para aplicações a estruturas costeiras).Apresenta-se a metodologia de acoplamento dos modelos SWAN, Bouss2D e SPHyCE, para modelar apropagação das ondas do largo até ao quebra-mar, assim como as campanhas de campo. São analisados ecomparados os galgamentos obtidos com o modelo numérico e os medidos.
Year: 2014
Number Pages:
143-146pp.
Author(s): Didier, E.; Ferreira, Ó.; Dias, J.; Neves, D. R.; Carrasco, A. R.; Reis, M. T.; Neves, M. G.
Keywords: Dados de campo; Quebra-mar; Galgamento; Smoothed particle hydrodynamics
Info
HIDRALERTA Project
This paper describes the recent advances on the research project HIDRALERTA - "Flood Forecast and Early Warning System in Coastal and Port Areas", whose main objective is developing a system for forecasting, warning and assessment of risks associated with wave overtopping and flooding in coastal and port areas, supported by measurements/predictions of waves and water levels in these areas. The case study here presented is the port and bay of Praia da Vitória, at the Terceira Island, Azores. Methodologies and accomplishments of the HIDRALERTA project achieved so far, with the focus on its more relevant results, are herein described.
Year: 2014
Number Pages:
8p.
Author(s): Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.; Capitão, R.; Santos, J. A.; Pinheiro, L.; Craveiro, J.; Rodrigues, A.; Sabino, A.; Silva, S.; Ferreira, J.; Raposeiro, P.; Silva, C.; Rodrigues, M. C.; S
Keywords: Risk assessment; Flooding; Wave overtopping; Wave conditions; Warning system
Info
Influência das correntes no comportamento do modelo SWAN na zona de Diogo Lopes, Brasil
A zona de Diogo Lopes, situada no estado do Rio Grande do Norte, Brasil, foi alvo devários estudos interdisciplinares, que incluíram a caracterização da agitação marítima ao longodesta costa (Ângelo et al. 2012, Matos et al. 2013). Esta é dominada por um regime de alternânciade brisa marítima e terrestre que colocou certas dificuldades. Para obviar a estas, recorre-se,novamente, ao modelo SWAN para a simulação do estado de mar, mas com um domínio decálculo alargado, um campo de ventos, obtido na estação meteorológica de Macau, diferente ecom a introdução da interacção das ondas e correntes. Estas são provenientes do modelohidrodinâmico SISBAHIA desenvolvido na referida Universidade. O forçamento ao largo é obtidorecorrendo ao modelo Wavewatch III. Para a verificação das simulações, utilizaram-se mediçõesde sensores AWAC para o período de 11 a 12 de Dezembro de 2010, em dois pontos distintos damalha computacional.
Year: 2014
Number Pages:
199-202pp.
Author(s): Ramos, A.; Fortes, C. J. E. M.; Pires Silva, A.; Scudelari, A. C.
Keywords: Rebentação parcial; Agitação marítima; Sisbahia; Diogo lopes; Ondas-correntes; Swan
Info
Modelagem numérica e física de um quebra-mar poroso
Os modelos Lagrangianos de tipo Smoothed Particle Hydrodynamics (SPH) apresentam-se como uma alternativa interessante para modelar a interação entre ondas e estruturas costeiras e marítimas. Estes modelos permitem representar corretamente a física dos fenômenos. No entanto, como qualquer modelo numérico, a precisão dos resultados depende fortemente da resolução, i.e. da dimensão das partículas. O estudo de análise da convergência com a resolução, para a elevação da superfície livre e o galgamento, mostra assim que a convergência é obtida para resoluções diferentes em função do tipo de fenômeno analisado e para resoluções mais finas quando a não-linearidade dos fenômenos aumenta. Os resultados numéricos foram comparados com os dados experimentais obtidos em canal de ondas evidenciando a convergência quer da elevação de superfície livre quer do galgamento com a resolução.
Year: 2014
Number Pages:
8p.
Author(s): Didier, E.; Neves, D. R.; Dias, J.; Teixeira, P.; Neves, M. G.
Keywords: Galgamento; Quebra-mar poroso; Smoothed particle hydrodynamics
Info
Monitoramento de ondas geradas por ventos em recintos fechados utilizando o modelo numérico SWAN e sensor de pressão
A geração e propagação de ondas de vento em lagos de barragens de grande dimensãopode por em causa a segurança da navegação interior bem como contribuir para aocorrência de fenómenos erosivos nas margens desses lagos. É, por isso, muito importantea correta estimação dessas ondas de vento e o desenvolvimento de metodologias eferramentas capazes de promover a sua monitorização e a previsão atempada dessasondas de modo a minimizar as suas consequências do ponto de vista económico eambiental.É, neste âmbito, que se insere o trabalho que está a ser desenvolvido para o lago dabarragem de Ilha Solteira no estado de São Paulo, Brasil, onde um vasto conjunto de dadosin situ (ventos, ondas, correntes e sedimentos) está a ser coletado desde 2007 assim comose iniciaram as aplicações de modelos numéricos de geração e propagação de ondas.Nesta comunicação, apresenta-se a comparação das estimativas produzidas pelo modelonumérico SWAN, utilizando a caracterização do vento obtida a partir do Anemómetro 2Dsônico instalado no lago da barragem de Ilha Solteira, com as medições da elevação dasuperfície livre obtidas com o sensor de pressão instalado a 1 m da superfície e 8 m deprofundidade local para um período de 2 meses (janeiro e fevereiro de 2011).As comparações efectuadas mostram a capacidade do modelo SWAN em reproduzirglobalmente as características de agitação verificadas no lago em função da boaconcordância entre os valores experimentais e os resultados do modelo numérico, onde em97% dos casos se obteve um índice de concordância (IC) de 73%.
Year: 2014
Number Pages:
13p.
Author(s): Vieira, A. S.; Fortes, C. J. E. M.; Maciel, G.
Keywords: Swan; Sensor de pressão; Segurança da navegação; Ondas de vento; Ilha solteira
Info
Normas e recomendações em obras marítimas
N/A
Year: 2014
Number Pages:
24p.
Author(s): Neves, M. G.
Keywords: Recomendações; Dimensionamento hidráulico-estrutural; Obras marítimas
Info
Numerical analysis of flow-induced vibration of two circular cylinders in tandem at low Reynolds numbers
Uniform flows over circular cylinders in different arrangements appear in manypractical situations. Analyses of side-by-side, tandem and staggered arrangements have shownsignificant differences among flow parameters and the interaction of the flow and the cylinder,by comparison with single cylinder parameters. This paper describes the study of two circularcylinders in tandem arrangement subject to bi-dimensional uniform laminar flows at lowReynolds numbers from 90 to 140. Cases with distance between cylinders equal to 5.25diameter for both fixed cylinders and for a fixed upstream cylinder and a downstream oneelastically mounted in transversal direction are analysed. The numerical model Ifeinco, whichis based on the finite element method and uses a partitioned scheme that considers two-wayinteraction of fluid flow and structure, is employed in the analysis. The fluid flow model usesa semi-implicit two-step Taylor-Galerkin method to discretize the Navier-Stokes equations andthe arbitrary Lagrangean-Eulerian formulation to follow the cylinder motion. The analysis ofthe cylinder movement is carried out by using one DOF dynamic equation for the transversedirection discretized in time by the implicit Newmark method. For both fixed cylinders,differences in terms of lift and drag coefficients and Strouhal number are found by comparisonwith the ones of the single cylinder. When the downstream cylinder is elastically mounted, alock-in phenomenon is observed in a range of Reynolds numbers, characterized by thediscontinuity of the lift and drag coefficients, vortex vibration and natural frequenciesapproximation and increase in vibration amplitude.
Year: 2014
Number Pages:
2160-2171pp.
Author(s): Teixeira, P.; Didier, E.
Keywords: Wake interference; Tandem arrangement; Circular cylinders; Flow-induced vibration; Finite element method
|
|
Capítulo de Livro
Info
Multi-functional artificial reefs for coastal protection
N/A
Year: 2009
Number Pages:
153-210 pp.
Author(s): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Tese de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Year: 1999
Number Pages:
159 p.
Author(s): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Year: 1998
Number Pages:
594 p.
Author(s): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Year: 1998
Number Pages:
346 p.
Author(s): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Year: 1973
Author(s): Carvalho, M. M.
Editor: ******
|
|
Relatório Científico
Info
An integrated harbour navigation control system. NATO Po-Navigation. Adenda ao "Project Plan" proposto ao "Programa Ciência para a Estabilidade. Fase III" da OTAN
N/A
Year: 1994
Author(s): Covas, J. A.
Info
Cais da Calheta, Ilha de S. Jorge - Açores. Memorando
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios em modelo reduzido de uma protecção marítima aderente.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios tridimensionais de estabilidade e galgamentos do molhe de protecção do porto de recreio náutico do porto de Sines.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Análise das condições do porto de Sines. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Selecção de locais viáveis. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Ligação da lagoa de Óbidos ao mar - Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Carvalho, M. M.; Capitão, R.; Fortes, C. J. E. M.; Covas, J. A.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Coimbra.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.; Capitão, R.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Palma de Maiorca.
N/A
Year: 1994
Author(s): Covas, J. A.
|
|
|
Outro
Info
Relato da missão a Bruxelas (28 a 30 de Outubro de 1998) para participação na 10ª Reunião da Acção Concertada Added Value Services in VTMIS do Programa Comunitário de I&D TRANSPORTS . Relatório efe
N/A
Year: 1998
Number Pages:
3 p.
Author(s): Covas, J. A.
Editor: ******
Info
Short-term stochastic numerical and physical simulation of sea waves - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI, na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
53 p.
Author(s): Capitão, R.; Pires Silva, A.; Medina, J. R.; Carvalho, M. M.
Editor: ******
Info
Transformações Não-Lineares de Ondas Marítimas em Zonas Costeiras - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI , na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
50 p.
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Editor: ******
Info
V Programa Quadro da União Europeia. Preparação da discussão dos Programas Específicos. Documento de trabalho da Comissão (COM (97) 553 Final). Grupo de Trabalho 6 Sustainable Mobility and Intermod
N/A
Year: 1998
Number Pages:
2 p.
Author(s): Covas, J. A.
Editor: ******
Info
Valores extremos da agitação marítima no Algarve - Proposta de Projecto de Investigação apresentado ao Programa de Intervenção nos Laboratórios do Estado (MCT-FCT), sub-projecto Valorização e Protec
N/A
Year: 1998
Number Pages:
11 p.
Author(s): Carvalho, M. M.; Capitão, R.
Editor: ******
|