Publications

Knowledge of forces due to the action of waves on submarine outfalls composed by a pipe and stabilizing concrete weights, considering the wave propagation direction to the outfalls, is essential to their design. 3D numerical models based on RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid) are able to estimate forces on the pipe and weights. The present study aims to simulate a submarine outfall with stabilizing concrete weights at 1:15 scale which was previously tested in the 3D Shallow Water Basin at the Danish Hydraulics Institute (DHI) to analyse the influence of the direction of the incident wave and the distance from the pipe to the bottom on the outfall forces. In this study, numerical results are compared with experimental ones for waves with four different amplitudes and with wave incidence perpendicular to the outfall. The use of k-

The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.

Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.

This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira

This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.

This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.

Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula

This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the

The ultimate goal of applying SWASH in the present work is to compare SWASH wave height results with laboratory results presented in Løvås (2000) and with field observations of Vo-Luong and Massel (2008) as well. Additionally, SWASH results will be also compared to the ones previously obtained by other empirical and numerical models (Mendez and Losada, 2004; Suzuki et al., 2012).Preliminary SWASH wave height simulations for breaking random waves over vegetation have shown an overall good agreement to the flume data presented in Løvås (2000). The agreement between SWASH and flume results looked worst at the wave breaking zone, which seems to be improved through a better wave breaking parametrization.

Most of the previous studies on wave propagation over vegetation fields estimated drag coefficients (CD) for rigid and flexible plants by the so called calibration method which gave similar CD for both types of plants. However, CD may actually be considerably different when the drag force is directly measured. In order to investigate the wave dissipation and CD further, flume experiments for wave propagation over vegetation are conducted with a special focus on the benchmark single cylinder test that calculates CD by direct measurements in single rigid and flexible artificial plants.

O projeto BSafe4Sea visa desenvolver, testar e comprovar o conceito de previsão do comportamento estrutural de quebra-mares de talude como a base de um sistema inovador de apoio à decisão. A utilização de fotografias aéreas obtidas com veículos aéreos não tripulados, de vídeo e de posicionamento com GNSS, juntamente com a avaliação probabilística do comportamento dos quebra-mares baseada em modelos físicos e numéricos, apoiarão o planeamento e a priorização de trabalhos de manutenção e reparação, aumentando a segurança, funcionalidade e resiliência destas obras. Este sistema é urgente devido à sua relevância para as modernas redes de transporte de mercadorias e passageiros e às condições extremas a que os quebra-mares estão sujeitos, e que se poderão agravar devido às alterações climáticas.

This paper describes a programme under the responsibility of LNEC for the systematic observation and monitoring of maritime works that has successfully been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad.The now-called OSOM+ programme comprises the following four main components for each structure: periodic visual inspections by an experienced technician; periodic aerial inspections with a UAV/drone; a ANOSOM-GIS database, to store and/or query obtained information on the observation campaigns, as well as to diagnose present, evolution and risk conditions of the structure; a mobile, portable, application, for real-time input and visualization of the database information.This recently updated methodology encompasses a number of tools and functionalities that are illustrated in this paper with applications to a real case, the Faro-Olhão

In this paper, the development of such system, called SWAMS ALERT, is detailed and an illustration on how it applies to a real port is presented, namely the port of S. Roque do Pico. SWAMS ALERT is as risk forecast and management system for the safety of transiting ships and moored ships in ports and harbors. This system can be fine-tuned to a specific port, thus becoming a valuable tool to help in the selection of docking and mooring devices. SWAMS ALERT extends the functionality of the wave overtopping events forecast system HIDRALERTA to include the ship

Since 1986, the National Laboratory for Civil Engineering (LNEC) has developed a program for Systematic Observation of Maritime Works (OSOM) for the structures under the responsibility of the former Port and Maritime Transport Institute (IPTM).The objective of this program is to monitor the behavior of the structures and recommend timely interventions for their maintenance and/or repair. Recently, with the acquisition by LNEC of an unmanned aerial vehicle (UAV, or drone), a number of structural surveys have been carried out to complement the information obtained in above mentioned visual observation campaigns. The UAV provides more detailed and accurate information on the state of the structures. It also allows the assessment of the evolution of structures

Neste artigo descreve-se o trabalho desenvolvido, até ao presente na construção, desenvolvimento e implementação dos 2 novos protótipos do sistema HIDRALERTA para os portos da Madalena do Pico e de S. Roque do Pico, ambos na Ilha do Pico, Açores. Este sistema permite a previsão e alerta de situações de emergência relacionadas com agitação marítima, galgamentos, inundações.

The recent acquisition of an UAV (Unmanned Aerial Vehicle), or drone, has enriched ongoing LNEC

Nesta comunicação analisa-se a influência da variação da profundidade na interação hidrodinâmica entre dois navios, um estacionário e outro navegando na vizinhança, com recurso à modelação física e numérica. O navio em movimento é um modelo autopropulsionado à escala do navio de transporte de produtos químicos

O conhecimento das forças devido à ação das ondas que atuam nos emissários submarinos compostos por uma conduta e anéis de estabilização de betão, para agitação com direção de propagação próxima da direção do emissário, é essencial para o seu dimensionamento. Esta é uma configuração complexa, para a qual a modelação numérica, utilizando modelos 3D de tipo RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid), é especialmente adequada para obter uma estimativa das forças na conduta e nos anéis. O presente estudo consiste na simulação de um emissário submarino com anéis de estabilização à escala 1:15 que foi ensaiado num tanque de ondas tridimensional, nas instalações do Danish Hydraulics Institute (DHI), para estudar a influência da direção da agitação incidente e da distância da conduta ao fundo nas forças que atuam no emissário. Foram realizados ensaios sem e com anéis (2 tipos de anéis), para diferentes condições de agitação e direções de agitação incidente (90º, i.e., perpendicular à conduta, 30º e 10º) e para três distâncias da conduta ao fundo (0.0, 0.020 e 0.033m). Os resultados numéricos são comparados aos experimentais para agitação com direcção de propagação perpendicular ao emissário, para 3 alturas de onda incidente. Verificou-se que o modelo de turbulência k-

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A