Publications

O Porto de Leixões, localizado na costa norte de Portugal, é um dos maiores do país, recebendo diariamentevários navios de grandes dimensões. Um dos principais postos de acostagem situa-se à entrada do porto e encontra-se sujeito à agitação marítima que é difratada pelo olhe principal de proteção do porto. Para avaliar dos movimentos induzidos no navio estacionado nesse posto de acostagem e as forças exercidas nas suas amarras e defensas pela agitação incidente, utilizou-se o modelo físico de Leixões, construído num dos tanques do LNEC. Neste modelo físico, encontra-se representada a envolvente do porto de Leixões, assim como a sua batimetria. O modelo do navio

An alternative to the energy matrix expansion, due to the increase of global electricity demand, is the renewable sea wave energy source, which has high energy potential. The Oscillating Water Column (OWC) converter is one of the most studied, although it is not yet used at commercial scale. Therefore, searching the optimal geometric configuration is fundamental to turn this device viable. This study proposes a numerical analysis of an onshore OWC for different slopes of chamber walls (from 40o to 90o) and equipped with a Wells turbine. Simulations of incompressible 2D flows are performed by means of the FLUENT® software, which is based on Reynolds-averaged Navier-Stokes (RANS) equations. The k-

The most studied device used for extracting wave energy is the Oscillating Water Column (OWC). In general, numerical simulations of these cases by means of models based on Reynolds Averaged Navier-Stokes equations adopt the Volume of Fluid method to deal with the free surface flow which is considered incompressible in both water and air. The aim of this study is to investigate the influence of the compressibility effect on the air inside the OWC chamber by the FLUENT® numerical model. A methodology is implemented, taking into account both water and air flows incompressible, but, at every instant, a pressure condition is imposed on the top boundary of the chamber to consider the compressibility effect. This pressure condition is based on an analytical equation that considers the isentropic transformation of the air and effects of Wells and impulse turbines. Results of compressible and incompressible numerical models are compared. The amplification factor, the root mean square of air pressure inside the chamber and OWC efficiency in relation to incident wave period, wave height and turbine characteristic relation are analyzed. Results show that air compressibility effects can diminish the predicted OWC efficiency up to about 20% in both Wells and impulse turbines.

In this study, a numerical analysis of the performance of two Oscillating Water Column (OWC) wave energy converters, at different front and back wall slopes, was carried out. The first device had vertical front and back walls and the second one had its wall slopes of 40° in relation to the horizontal plane. The FLUENT® numerical model, which is based on the Reynolds-Averaged Navier-Stokes (RANS) equations, was used. The Volume of Fluid (VoF) method was employed to take into account free surface flows. The case study comprised a 10 m deep flume with an onshore OWC at its end, equipped with a Wells turbine. A 2D hydrodynamic mathematical model was employed and a 3D air pressure effect inside the OWC air-chamber was considered. Analyses of the hydrodynamics behavior, fluid-structure interaction outside (run-up/down, reflected waves) and inside the chamber (free surface elevation, sloshing) and energy distribution (pneumatic extracted energy, reflected wave energy and energy losses) were conducted. Results showed that the device with inclined walls had the best efficiency in comparison with the other one. However, the latter showed lower variation in efficiency in the wave period range than the former.

The main objective of this study is to investigate differences of random incident waves from regular ones in performance of wave energy converters (WEC). A numerical analysis of an onshore oscillating water column (OWC) WEC is carried out by means of the FLUENT® software, which is based on Reynolds - Averaged Navier-Stokes equations. Analyses of the efficiency of an onshore OWC device with similar characteristics of the Pico

Atualmente, mais importante que assegurar a resistência de um aglomerado urbano a um eventual invasor, importa garantir a sobrevivência a catástrofes naturais das infraestruturas críticas que garantem a salubridade das condições de vida nesse aglomerado, a mobilidade dos habitantes e o abastecimento de bens essenciais. Em rigor, face ao carater aleatório destas solicitações, pretende-se que, uma vez terminadas essas solicitações extremas, eventuais estragos causados pelas mesmas não impeçam o restabelecimento, em tempo útil, das atividades normais da população. Nesta comunicação apresentam-se ferramentas e procedimentos para avaliação do risco associado a infraestruturas críticas com um viés para o controlo de cheias urbanas e de infraestruturas de transporte marítimo.

The current program of Systematic Observation of Maritime Works (OSOM+), under development at the National Laboratory for Civil Engineering (LNEC), is essentially applied to rubble mound breakwaters. The OSOM

HIDRALERTA is a forecast and early warning system for coastal and port regions capable of predicting emergency situations, as well as carrying out risk assessment. The system concentrates on evaluating wave overtopping and flooding scenarios. It uses offshore sea-wave and wind forecast data, as well as tide data, as input to determine wave overtopping at specific locations. The calculation of the mean overtopping discharge over a structure is made through artificial neural network (ANN) tools and/or empirical formulae, which are able to define the spatial distribution of the flow behind the structure.The HIDRALERTA system is composed of four modules developed in Open Source Web Technology, mainly using the Python Language. The Warning System can be configured and adapted for specific scenarios. The system has been successfully tested for the Port and Bay of Praia da Vitória, Terceira Island, Azores, Portugal, and is now under development and being implemented at the ports of Madalena do Pico and S. Roque do Pico.This paper describes the work carried out to date on the system and its application to these two ports in the Pico Island, Azores.

A set of scale-model tests carried out to enlarge the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater

Mechanical constraints have a non-negligible influence in the motion of oscillating wave surge converter (OWSC) devices. The key novelty of this paper is a numerical simulation tool for OWSCs that does not neglect or significantly compromise mechanical constraints such as hydraulic power take-off (PTO) system, revolute joints and frictional contacts among components. The paper is aimed at presenting the key components of the numerical simulation tool and at validating it with laboratory data featuring an OWSC with mechanical constraints under regular and irregular waves. It is based on the implementation of the multibody solver of Project Chrono under the Smoothed Particle Hydrodynamics (SPH) model of DualSPHysics, where the SPH solver resolves the interaction between wave and flap and the multibody solver resolves the interaction between flap and mechanical constraints. Comparison between numerical results and experimental data show that the numerical simulation tool properly predicts the dynamics of the OWSC. Furthermore, in what concerns hydrodynamics of the near-flap flow, the computed and measured free-surface elevations and phase-averaged flow field show reasonable agreement. Once properly validated, the numerical simulation tool is then applied to study the influence of several mechanical constraints, PTO damping characteristics and flap inertia on the hydrodynamic of the OWSC. The viability of OWSC design solutions based on the developed numerical simulation tool is emphasised, in view of its performance in the test cases to which it was subjected.

The ultimate goal of applying SWASH in the present work is to compare SWASH wave height results with laboratory results presented in Løvås (2000) and with field observations of Vo-Luong and Massel (2008) as well. Additionally, SWASH results will be also compared to the ones previously obtained by other empirical and numerical models (Mendez and Losada, 2004; Suzuki et al., 2012).Preliminary SWASH wave height simulations for breaking random waves over vegetation have shown an overall good agreement to the flume data presented in Løvås (2000). The agreement between SWASH and flume results looked worst at the wave breaking zone, which seems to be improved through a better wave breaking parametrization.

Most of the previous studies on wave propagation over vegetation fields estimated drag coefficients (CD) for rigid and flexible plants by the so called calibration method which gave similar CD for both types of plants. However, CD may actually be considerably different when the drag force is directly measured. In order to investigate the wave dissipation and CD further, flume experiments for wave propagation over vegetation are conducted with a special focus on the benchmark single cylinder test that calculates CD by direct measurements in single rigid and flexible artificial plants.

O projeto BSafe4Sea visa desenvolver, testar e comprovar o conceito de previsão do comportamento estrutural de quebra-mares de talude como a base de um sistema inovador de apoio à decisão. A utilização de fotografias aéreas obtidas com veículos aéreos não tripulados, de vídeo e de posicionamento com GNSS, juntamente com a avaliação probabilística do comportamento dos quebra-mares baseada em modelos físicos e numéricos, apoiarão o planeamento e a priorização de trabalhos de manutenção e reparação, aumentando a segurança, funcionalidade e resiliência destas obras. Este sistema é urgente devido à sua relevância para as modernas redes de transporte de mercadorias e passageiros e às condições extremas a que os quebra-mares estão sujeitos, e que se poderão agravar devido às alterações climáticas.

This paper describes a programme under the responsibility of LNEC for the systematic observation and monitoring of maritime works that has successfully been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad.The now-called OSOM+ programme comprises the following four main components for each structure: periodic visual inspections by an experienced technician; periodic aerial inspections with a UAV/drone; a ANOSOM-GIS database, to store and/or query obtained information on the observation campaigns, as well as to diagnose present, evolution and risk conditions of the structure; a mobile, portable, application, for real-time input and visualization of the database information.This recently updated methodology encompasses a number of tools and functionalities that are illustrated in this paper with applications to a real case, the Faro-Olhão

In this paper, the development of such system, called SWAMS ALERT, is detailed and an illustration on how it applies to a real port is presented, namely the port of S. Roque do Pico. SWAMS ALERT is as risk forecast and management system for the safety of transiting ships and moored ships in ports and harbors. This system can be fine-tuned to a specific port, thus becoming a valuable tool to help in the selection of docking and mooring devices. SWAMS ALERT extends the functionality of the wave overtopping events forecast system HIDRALERTA to include the ship

Since 1986, the National Laboratory for Civil Engineering (LNEC) has developed a program for Systematic Observation of Maritime Works (OSOM) for the structures under the responsibility of the former Port and Maritime Transport Institute (IPTM).The objective of this program is to monitor the behavior of the structures and recommend timely interventions for their maintenance and/or repair. Recently, with the acquisition by LNEC of an unmanned aerial vehicle (UAV, or drone), a number of structural surveys have been carried out to complement the information obtained in above mentioned visual observation campaigns. The UAV provides more detailed and accurate information on the state of the structures. It also allows the assessment of the evolution of structures

Neste artigo descreve-se o trabalho desenvolvido, até ao presente na construção, desenvolvimento e implementação dos 2 novos protótipos do sistema HIDRALERTA para os portos da Madalena do Pico e de S. Roque do Pico, ambos na Ilha do Pico, Açores. Este sistema permite a previsão e alerta de situações de emergência relacionadas com agitação marítima, galgamentos, inundações.

The recent acquisition of an UAV (Unmanned Aerial Vehicle), or drone, has enriched ongoing LNEC

Nesta comunicação analisa-se a influência da variação da profundidade na interação hidrodinâmica entre dois navios, um estacionário e outro navegando na vizinhança, com recurso à modelação física e numérica. O navio em movimento é um modelo autopropulsionado à escala do navio de transporte de produtos químicos

O conhecimento das forças devido à ação das ondas que atuam nos emissários submarinos compostos por uma conduta e anéis de estabilização de betão, para agitação com direção de propagação próxima da direção do emissário, é essencial para o seu dimensionamento. Esta é uma configuração complexa, para a qual a modelação numérica, utilizando modelos 3D de tipo RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid), é especialmente adequada para obter uma estimativa das forças na conduta e nos anéis. O presente estudo consiste na simulação de um emissário submarino com anéis de estabilização à escala 1:15 que foi ensaiado num tanque de ondas tridimensional, nas instalações do Danish Hydraulics Institute (DHI), para estudar a influência da direção da agitação incidente e da distância da conduta ao fundo nas forças que atuam no emissário. Foram realizados ensaios sem e com anéis (2 tipos de anéis), para diferentes condições de agitação e direções de agitação incidente (90º, i.e., perpendicular à conduta, 30º e 10º) e para três distâncias da conduta ao fundo (0.0, 0.020 e 0.033m). Os resultados numéricos são comparados aos experimentais para agitação com direcção de propagação perpendicular ao emissário, para 3 alturas de onda incidente. Verificou-se que o modelo de turbulência k-

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A