Publications

Salt decay is one of the harshest, most frequent and more complex types of decay of porous materials in built heritage, including natural stones, ceramics and mortars. In this article, we address the mechanism of thermal expansion which is one of the least studied, yet most controversial, of those proposed over time to explain salt decay. We present a review of scientific literature on the topic, followed by a study of the effects of thermal expansion on a specific material, the well-known Ançã limestone. The study included experimental measurement of the linear thermal expansion coefficient of the Ançã, both in its natural state and with varying contents of sodium chloride, sodium sulphate or sodium nitrate. The results show that this coefficient: (i) is significantly higher when the stone is contaminated with salt; (ii) scales approximately with the amount of salt contained in the stone pores, regardless of the type of salt. Based on these results and on modelling of damage modes at the microscopic and macroscopic levels respectively, we conclude that thermal expansion can cause powdering, disaggregation or other types of decay consisting in internal loss of cohesion. However, it is not likely to cause exfoliation of salt loaded layers.

The paper reviews the importance and distinguishing character of façade azulejo frames as used in the region of Lisbon and presents and discusses the early frame patterns designed and produced by Fabrica Roseira in the mid-19th century.

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP ‘‘Applications of Superabsorbent Polymers in Concrete Construction’’. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant toconsiderably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

Debate-se a relação entre conhecimentos tecnológicos tradicionais e científicos como inovadora e fundamental para a conservação do património. Considera-se que a inovação não advém necessariamente do conhecimento científico, mas potencialmente de uma sábia articulação entre estes dois tipos de conhecimentos. Parte-se de um já longo processo de reflexão sobre a conservação do património com base em cal, conforme desenvolvido no LNEC a partir de projetos de investigação.

The most serious form of degradation of historical azulejos is the spall of the glaze and it is widely accepted that the crystallization of salts dissolved in water circulating in the masonry is its main cause. This article reports the results of an accelerated aging test aimed at studying the physical deterioration of azulejos caused by cycles of dissolution and re-crystallization of sodium chloride (NaCl). Experiments were carried out on 26 Portuguese azulejos from the 17th–19th century, some of which with original manufacturing defects or with varying degrees of previous decay.

The restoration materials currently used to fill gaps in historical architectural tiles (e.g. lime or organic resin pastes) usually show serious drawbacks in terms of compatibility, effectiveness or durability. The existing solutions do not fully protect Portuguese faïence tiles (azulejos) in outdoor conditions and frequently result in further deterioration. Geopolymers can be a potential solution for tile lacunae infill, given the chemical–mineralogical similitude to the ceramic body, and also the durability and versatile range of physical properties that can be obtained through the manipulation of their formulation and curing conditions. This work presents and discusses the viability of the use of geopolymeric pastes to fill lacunae in tiles or to act as “cold” cast ceramic tile surrogates reproducing missing tile fragments. The formulation of geopolymers, namely the type of activators, the alumino-silicate source, the quantity of water required for adequate workability and curing conditions, was studied. The need for post-curing desalination was also considered envisaging their application in the restoration of outdoor historical architectural tiles frequently exposed to adverse environmental conditions. The possible advantages and disadvantages of the use of geopolymers in the conservation of tiles are also discussed. The results obtained reveal that geopolymers pastes are a promising material for the restoration of tiles, when compared to other solutions currently in use.

A procedure is proposed to assess the compatibility of cleaning actions to be carried out upon built heritage. This procedure was designed as a semi-quantitative (in)compatibility risk assessment, where the vulnerability of the substrate to cleaning, the aggressiveness of the cleaning method and the substrate/method synergies are factors considered to determine the likelihood of damage occurring, whereas the impact on the significance of the object measures the consequences of damage occurring. Rating these factors of likelihood and consequences of damage allows a cleaning risk matrix to be proposed for the evaluation of the risk levels implicated by different cleaning methods. Furthermore, planning components entirely contingent of their specific actors, and therefore inherently difficult to grade, such as operator skills or control adequacy, are included as quality components, which work as multiplying parameters of the overall risk. The procedure was conceived to assist in and frame the planning of built heritage cleaning actions. A Delphi Panel of conservation experts was convened to validate this proposal

The paper focuses on the study of barium hydroxide applied to two high porosity limestones from Portugal (Ançã stone, with 27% porosity) and Italy (Lecce stone, with 37% porosity), both in the laboratory and onsite. The results show that barium hydroxide acts both through carbonation with atmospheric CO2 and by replacing calcium for barium in the calcite lattice followed by carbonation of the released calcium hydroxide. This double mechanism proved to be particularly efficient in the Ançã limestone, possibly due to a higher reactivity linked to its smaller grain size. The mechanism is far slower than simple carbonation and has a better outcome when the stone can be totally immersed in the solution. Onsite experiments on the Ançã stone were less striking than in the laboratory, possibly due to the insufficient amount of product made available for reaction, but a positive outcome was visible after six years of natural exposure.

Knowledge of current conservation materials and methods together with those adopted in the past is essential to aid research and improve or develop better conservation options. The infill and painting of tile lacunae are subjected to special requirements mainly when used in outdoor settings. A selection of the most commonly used materials was undertaken and performed based on inquiries to practitioners working in the field. The infill pastes comprised organic (epoxy, polyester), inorganic (slaked lime, hydraulic lime and zinc hydroxychloride) and mixed organic–inorganic (slaked lime mixed with a vinylic resin) binders. The selected aggregates were those most commonly used or those already present in the commercially formulated products. The infill pastes were characterised by SEM, MIP, open porosity, water absorption by capillarity, water vapour permeability, thermal and hydric expansibilities and adhesion to the ceramic body. Their performance was assessed after curing, artificial ageing (salt ageing and UV–Temp–RH cycles) and natural ageing. The results were interpreted in terms of their significance as indicators of effectiveness, compatibility and durability.

Em Portugal, os interiores de igrejas, espaços conventuais e palácios estão frequentemente decorados com revestimentos azulejares desde finais do séc. XVI. Mas nem todos chegaram aos nossos dias em boas condições. O presente estudo teve como objetivo levantar formas de degradação in situ e eventualmente relacioná-las com a ocorrência de sais solúveis. Pretendia-se também identificar os sais correlacionando-os com a forma de degradação. Analisaram-se eflorescências e pequenos fragmentos de chacota e vidrado colhidos em obra, utilizando o microscópio eletrónico de varrimento com unidade de microanálise associada (SEM-EDS), para a identificação de espécies salinas.

Bonding on site has been used successfully for many years in the repair and strengthening of timber structures. However, there is still a lack of knowledge about its service durability, especially under high service temperature conditions. Not only the performance and durability of epoxy adhesives depend on their thermal stability but also on the preparation and application procedures followed on site, as confirmed by tests conducted by the authors to evaluate the effects of mixture ratios and curing conditions. This paper discusses a number of test methods that can be used for quality control of structural repair jobs involving bonding on site. Two studies conducted at LNEC where these methods were applied are presented: one concerning a structural intervention on a decorative suspended ceiling, the other concerning the selection of adhesives suitable for high service temperature conditions as expected in some roofs. DMA and FTIR analysis results are presented and their high potential for quality control during and after adhesive application is discussed.

The leachability study was made using a low strength concrete containing fly ash, with a compressive strength of 16.3 MPa intended to facilitate the leaching and the subsequent quantification of the hazardous metals released. The leachability tests were performed in the following samples: on cement, on a mixture of cement with fly ash, on ground concrete; and on a monolithic concrete cube. Two methods were used: static leaching; and dynamic leaching with the aim of determining relationships between the leachability of heavy metals from the individual components of cement and fly ash, and from concrete itself. The leachates at 7, 14, 28 and 63 days were characterized for the following metals: cadmium, lead, chromium, nickel, copper and zinc. From the leachability results it was concluded that only cadmium had concentrations below the detection limit of the analytical method, and that chromium, copper and zinc were the metals most prone to be leached. Leachates from concrete cubes with higher time of cure show higher concentrations of metals than concrete with less time of cure

Um requisito importante de uma junta colada, é a sua capacidade para manter um desempenho satisfatório durante a vida útil da estrutura, mesmo nas situações em que esta é exposta a condições extremas de temperatura e humi-dade. Uma das etapas mais importantes para a obtenção de uma colagem com uma boa durabilidade é a preparação da superfície dos substratos antes da colagem. Nesta comunicação é feita a avaliação quantitativa da eficácia de dois tipos de tratamentos de superfície (chama e descarga corona). Os seus efeitos foram estudados em três madeiras diferentes (pinho, câmbala e carva-lho) através da medição de ângulos de contacto utilizando o método de Wilhelmy. Os resultados obtidos mostraram que houve um melhoramento da molhabilidade das madeiras, em especial, com o tratamento por corona.

This paper is based on a study of the protection performance of varnishes applied to a wooden substrate for outdoor exposure. The aim of the work was the evaluation of some of the test methods that are often used in the coating industry to determine the durability of coating systems: determination of film thickness, designation of quantity and size of defects, and of intensity of uniform changes in appearance; determination of specular gloss and colour measurement. The methods were applied to eight varnish systems (with and without colorants and light stabilizers) that were subjected to artificial weathering and to natural weathering in outdoor exposure. The test methods used, to evaluate the appearance and physical-chemical properties of the coating during its degradation, seem to be able to select the best varnish formulation to the protection of wood for exterior uses and gave also an idea about their usefulness.

The results of the characterization of the sludge from a Portuguese water treatment plant and their leachates are presented. Dewatered sludge contains basically water, calcium, aluminium and silica, with an organic matter content of about 6%. The mineralogical constituents present in heated sludge are mainly calcite and clay minerals. Gibbsite is present only in the sludge heated at 105ºC and calcium aluminate and calcium oxide are only present in the sample heated at 700ºC. Thermal treatment does not remove the entire polymer and coagulant initially within the sludge. Sludges dewatered or heated at 105ºC inhibit the setting and hardening of the paste and the mortar so, and incorporation in mortars it is only feasible after treatment of the sludges at not less then 450ºC with an increase of the initial setting time but a decrease of the mechanical strength.

This communication is based on a work done in LNEC, which consisted in the study of the protection performance of varnishes applied in wood surfaces for exterior exposure. The objective of this work was to evaluate the efficiency of 8 different varnish systems (with and without colorants and light stabilizers) to protect and ornament two kinds of wood, allowing to determine the influence of the wood species in the varnish degradation. The results obtained lead to the selection of the best varnish formulation to the protection of wood for exterior uses. With this study was concluded that the acrylic aqueous varnish is a good alternative to the traditional kinds of varnishes.

This e-book and correspondent platform MyC3Place present the collection of the outcomes carried out by the partners of the C3Places Project. It explores the new dynamics of open spaces as a trusted service for community and expands our understanding on how mediated public open spaces function, paying attention to stakeholders, local context and different social groups. The e-book shows how it's possible to increase the quality of public open spaces (squares, parks, green spaces) as a community’s service, reflecting through ICT the needs of different social groups. Public spaces are critical for cultural identity, as they offer the place for interactions among generations and ethnicities. Even in the digital era, people still need contact with nature and other people to develop different life skills, values and attitudes, to be healthy, satisfied and environmentally responsible. Using ICT and co-creating with users, this e-book expands our knowledge on meeting emerging citizens’ needs about the future public space. All the contents are classified by means of keywords that are described on the following pages. Then the work of each partner is presented in detail.

C3Places - using ICT for Co-Creation of inclusive public Places is a project funded under the scheme of the ERA-NET Cofund Smart Urban Futures / Call joint research programme (ENSUF), JPI Urban Europe, https://jpi-urbaneurope.eu/project/c3places. C3Places aims at increasing the quality of public open spaces (e.g. squares, parks, green spaces) as community service, reflecting the needs of different social groups through ICTs. The notion of C3Places is based on the understanding that public open spaces have many different forms and features, and collectively add crucial value to the experience and liveability of urban areas. Understanding public open spaces can be done from a variety of perspectives. For simplicity’s sake, and because it best captures what people care most about, C3Places considers the “public” dimension to be a crucial feature of an urban space. Public spaces are critical for cultural identity, as they offer places for interactions among generations and ethnicities. Even in the digital era, people still need contact with nature and other people to develop different life skills, values and attitudes, to be healthy, satisfied and environmentally responsible. The book aims to spark discussion on the co-creation of public open spaces through the active involvement of different stakeholders in the production of a more inclusive, attractive and responsive urban environment. It intends to help researchers, governments and drivers in understanding and implementing more collaborative actions. The authors share experiences, visions and reflections on how co-creation and participatory processes can open up possibilities for a sustainable and equitable future. This book emphasises three dimensions: practice, reflection, and learning. Practice concerns driving actions, identified and analysed experiences that serve as key models. Reflection refers to exploring and examining the results and performances of a co-creation process. Co-creation is not the search for a final product, but rather a process and a new path to more responsive and inclusive communities. Learning refers to the knowledge transfer and replication induced by the synergy of the different actors involved in this book. The chapters which constitute this work were completed prior to Spring 2020, so the research and insights do not reference the global public health crisis caused by Covid-19. However, in such challenging times the argument for co-creation approaches to increase the potential of public spaces to support a range of inclusiveness outcomes is even stronger. This publication is based upon work of C3Places Project. The C3Places Project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 693443 and from FCT (Portuguese Funding Agency for Science, Research and Technology).

This volume aims to promote discussion and critical thinking on the urban environment at the intersection of the neighbourhood and the city, along their socio-spatial relations, from an interdisciplinary, multidimensional and international perspective. The chapters cover various aspects related to the meaning of living, intervening, planning, managing, thinking about and producing the city in the digital era, with a view to increasing the understanding of neighbourhoods as part of a wider consideration of social and sustainable development and the need for greater care of urban communities. This has a direct impact on public open spaces, which lie at the core of CyberParks. The international scope of the edition is enhanced by its bilingual nature, as this volume targets, in addition to a European readership, also the readership of Portuguese-speaking countries. This publication is based upon work from COST Action TU1306, supported by COST (European Cooperation in Science and Technology).

Vários

Publicação que regista os resumos expandidos realizados no âmbito do Congresso Ibero-americano "Património, suas matérias e imatérias", realizado nos dias 2-3 de novembro de 2016 no LNEC, contendo ainda em CDrom, os artigos completos.

Em 2011 cumpriram-se 100 anos sobre a publicação da Lei de Reorganização dos Serviços Artísticos e Arqueológicos da 1ª República (Maio de 1911). Este diploma constituiu uma referência incontornável no enquadramento do conceito de património que iria influenciar toda a prática da sua salvaguarda em Portugal. Por coincidência, cumpriram-se também neste ano os 80 anos da Carta de Atenas (Outubro de 1931), um marco histórico na produção de documentos orientadores de cariz internacional, que veio incentivar a produção de novas cartas e outros documentos internacionais que, em larga medida, ainda definem e sustentam as actuais práticas de preservação do património. O Instituto de História da Arte da Universidade de Lisboa e o Laboratório Nacional de Engenharia Civil quiseram com este simpósio assinalar aquelas efemérides oferecendo às comunidades científicas e profissionais uma oportunidade de reflectirem sobre estes acontecimentos pioneiros e debaterem as consequências que eles tiveram no período transcorrido desde então, como forma de compreender melhor a salvaguarda do património nos dias de hoje, perante os desafios e exigências da sociedade moderna. Os artigos recebidos, e que constam nas presentes actas, demonstram o interesse que o tema suscita e confirmam que o País está bem apetrechado para cuidar do seu património em todas as vertentes que tal objectivo exige. Ao juntarmos as valências de duas instituições tão diferenciadas, procurámos mostrar que a preservação é um conceito multifacetado, que necessita de contributos diversos, mas precisos, e que não pode ser abordado de forma unilateral ou voluntarista por um qualquer grupo profissional ou ditado por meios burocráticos como medida normalizada ou normalizável. Os trabalhos agora publicados dão conta dos primórdios das preocupações sobre preservação, discutem problemáticas que percorreram o Séc. XX e reflectem sobre as situações actuais, cumprindo cabalmente as nossas expectativas e enriquecendo o acervo de exemplos e de doutrinas que nos permitem afirmar que não é por falta de conhecimento, de experiências ou de competências realizadoras que ainda hoje vemos acontecerem intervenções desqualificadas, mal preparadas e desajustadas. As presentes actas aí estão para demonstrar que fazer mal ou abandonar património não têm que ser fatalidades de um país.

N/A

In the construction sector, overall policies on resource efficiency and the circular economy have as one of their objectives the shift from the use of natural mate-rials to industrial by-products and materials recovered from waste. In this context, the assessment of the presence of hazardous substances in construction products and the corresponding implications for the environment

The Lisbon Living Lab will be centred on teenagers (young people 13 to 17 years of age) as they are a particular age group with specific needs and interests on public spaces, the relationship between teens and public spaces is very intrinsic, as public spaces may serve as a fundamental (play)ground for teenagers’ development. The Lisbon’s Alvalade neighbourhood will be living lab to explore how teenagers use and behaviour in urban fabric and what are they needs and preferences on public open spaces. The main objective is to engage teenagers in a process of the co-creation of urban spaces, by exploring the leading research question: “How can we capitalise on teenagers’ new-found love of the wired life (Thomas, 2013) to encourage them to be more outdoors?”

This chapter explores the potential of co-creation for the planning of public open spaces that could be more attentive to different, unequal and diverse social ideas, needs and desires. Co-creation is discussed as an innovative opportunity for learning and (re)thinking urban planning. Exploring ideas, literature and experiences (from the European Project C3Places), the chapter discusses the role of co-creation for involving citizens in placemaking. This reflection addresses co-creation as a collective, contextual and engaged process of learning. From this perspective, co-creation is discussed as an open process of learning about predictable ideas in the relationship between socio-spatial imaginary, requirements, needs and urban design procedures from a transformative perspective.

Public open space is a subject that belongs to us all. Every time we leave our homes, our private territory, we enter a space we have to share with others. Public space is the place for social interactions, strengthening sociability and ultimately exercising democracy. As a subject of study, public space has also long been analysed, explored and researched in various ways and under different guises, by planners, landscape architects and designers, anthropologists, social and cultural geographers, and urban historians. They all bring evidence on the role of public space in urban life, in the quality of urban environment and in the construction of cultural identity. Consequently, public space should deserve serious consideration by all - starting with those in charge and who hold regulatory responsibilities for those who use the places and ultimately give them life. As the UN-Habitat (2015) rightly recognises, a public space represents a key resource for social cohesion, economic development, and in particular liveability in urban settings. Public space is a resource that critically affects community values and positively impacts the quality of urban life. Backed by these premises, this book is about the co-creation of public open spaces, an issue at the core of the C3Places Project. To better understand the process, particularly the values of engaging people in the production of public space, is one of the C3Places’ objectives. The project is developing strategies and tools to help increase the quality and responsiveness of public spaces. In this process, the Project also aims to better understand how Information and Communication Technologies (ICTs) can influence co-creation and social cohesion. The chapters of this book bring science a little closer to the knowledge about the design, production and management of public spaces. 37 authors responded to the Project’s call to share experiences, visions and reflections on how co-creation and participatory processes can create possibilities for a sustainable and equitable future.

Face à metamorfose que se presencia na região da Avenida Almirante Reis, este capítulo discute a sua correlação com a criação de um novo discurso sobre a diversidade sociocultural. A partir do apelo a determinadas expressões — por exemplo, mundo e mundos — para enunciar a diversidade local, sugere-se a crescente transfiguração do discurso e a conexão com a economia cultural amplamente estimulada pela intervenção ali protagonizada. No desenvolvimento desta reflexão, privilegia-se o discurso produzido pela comunicação social.

The chapter considers the link between urban transformations in the Mouraria neighbourhood in Lisbon and the digital environment.The guiding thread of reflection is based on the tension between the production of sociocultural symbolic local references, and their (dis)appropriation by a creative economy that, relying on digital as a resource, helps to reshape the sociocultural local world into marketing. It concludes that digital has, not only a tangible social dimension, but also a tangible dimension in the processes of urban transformation. As such, it is pertinent to create alternative ways in defence of the right to the city that economize the social and its imageries taking more advantage of the articulated combination between real-digital.

This chapter is concerned with how digital technologies are changing habits, expectations and motivations in the use of public open spaces. These digital developments are a societal challenge with reflections on social practices and, on planning and design approaches to public spaces. This might also challenge the future development of information and communication technologies (ICTs). The discussion in this Chapter is based on knowledge and experience exchanges carried out within the COST Action CyberParks. The leading issue of CyberParks is how to use ICTs to transform our cities into more human environments, rather than just more high-tech places, and to understand that “smartness” should be people friendly. Through the structure of the project, the importance of comprehensive and trans-disciplinary development is introduced and justified. A theoretical approach and frameworks from ethnographic and technological perspectives that help us to better understand (potential) interactions are being developed, and both are at the centre of this discussion.

The aim of this chapter is to discuss the production of mediated public open spaces by investigating the impact of ICTs in a participation process, and from this discussion to develop arguments to base a theory on co-creating a cyberpark. It focuses on how digital interconnectivity, through its potential for engaging potential users, gives rise to new forms of agency in the design of public spaces.The conceptual framework is backed by the COST-Action Cyberparks, and the Project Flussbad, both tackle the reflection of the proliferation of ICT-related media in public open spaces.

This chapter discusses the act of walking as a method of capturing the socio-spatial needs of users in a contemporary urban space. Walking as method is considered a way to assimilate a socio-spatial proximity experience, and to (re)invent the response to urban space needs in a fast-changing city. This reflection discusses the purposes of urban planning, provides a framework, which goes from socio-spatial urban needs to (possible) responses, and discusses the complexity of evaluating the information gathered. It highlights the role of walking in planning, but also the relationship between plan and walk, discussing some of the key aspects to bear in mind when taking the act of walking as a way to learn how to plan. From the sensitive act of walking to the rational processes of collecting information, e.g., techniques for basic information collection for urban planning, this chapter also presents the role that ICT can play as an instrument of socio-spatial design in capturing relevant information for urban planning professionals.

The chapter discusses how ICT can be used to enhance the understanding of the relationship between space, users and social practices. As an example of possible use of ICT for capturing and better understanding user’s needs, the new digital tool WAY Cyberparks is presented and discussed. A “cyberpark” is defined as a new type of urban landscape where nature and ICTs blend together to generate hybrid experiences and enhance quality of life. The WAY Cyberparks digital tool consists of a smart phone application, server/cloud and web services. Through the experiences from testing it in selected urban open spaces in Barcelona, Lisbon and Ljubljana opportunities are presented and lessons are drawn about relevant aspects of the ICT towards building a more participatory and collaborative process in planning of public spaces. A relevant aspect of the ICT lays in their ability to enhance communication with (potential) users, transforming the production of public open spaces into an interactive process, and enabling creative community participation and empowerment. Furthermore, some challenges of the increasing penetration of digital technologies devices (smart phones, smart watches, tablets, etc.) within the broader context of their use in public urban open spaces such as parks, gardens, squares, plazas are discussed, together with the consequences of this interweaving, which is growing at a rapid pace, unfolds research needs in the future.

Atualmente existe grande interesse pelas técnicas construtivas com terra crua, que tinham caído em desuso mas que ressurgiram com a conscencialização face à ecoeficiencia e no sentido de explorar recursos locais reutilizáveis. A taipa é, a nível mundial, uma das mais antigas e difundidas técnicas de construção. Em Portugal a taipa reune grande atenção porque é uma das principais técnicas utilizadas na nova construção com terra. Mas esta atenção decorre também da necessidade de reabilitação de edifícios antigos e da existência de um vasto e valioso património arquitetónico, que precisa ser preservado. Muitos dos edifícios antigos de terra deterioraram-se por falta (ou ineficiência) de manutenção e reparação. De fato, existe um elevado desconhecimento ao nível das técnicas de reabilitação e conservação. O presente trabalho de investigação explora a questão da adequabilidade de argamassas para a reparação de paredes de taipa. A escassa informação nesta área justificou o estudo das caraterísticas mais adequadas para estas argamassas de reparação e definição de recomendações para sua aplicação. Partiu-se do pressuposto que, para perspetivar intervenções de reparação com maior ciclo de vida, é importante asseverar não só a durabilidade das argamassas de reparação, mas também a sua compatibilidade com a parede. A principal conclusão é que, sempre que possível, as argamassas devem ser efetuadas com a mesma terra utilizada na parede ou com materiais tão semelhantes a esses quanto possível, para que as propriedades físicas, mecânicas e químicas sejam compatíveis com as da parede a reparar. Se a taipa não tiver sido estabilizada com ligantes minerais, estes não devem também ser utilizados nas argamassas de reparação. Observou-se ainda que as argamassas estabilizadas com ligantes minerais apresentam uma absorção capilar muito mais rápida do que o mesmo tipo de argamassas sem estabilização e que a utilização de fibras vegetais potencia o aparecimento de bolores, quando as argamassas se encontram em ambientes com elevadas humidade relativa.

This thesis was aimed at understanding the behaviour of plasters and renders on salt-loaded walls. The current state-of-the-art and state-of-the-practice were accessed focusing particularly on old plastered/rendered buildings and their conservation practice in Portugal. Afterwards, experimental work was carried out aiming at answering the identified questions. Two laboratory techniques, for relative humidity control with salt solutions and for salt content determination by hygroscopic moisture content measurements, were investigated. Drying of salt-loaded materials was studied by means of drying experiments monitored using a magnetic resonance imaging (MRI) technique. The behaviour of plasters and renders in relation to salt crystallization was then accessed by means of crystallization tests and MRI-monitored drying tests. Most drying and crystallization tests were carried out on specimens composed by a plaster or render applied on a given substrate. Finally, the study of five old buildings in Portugal provided an insight into practice-related salt decay features. On the basis of this research, guidelines are proposed to select plasters and renders for salt loaded walls. Conclusions were also achieved on: (i) possibilities and limitations of the test methods, particularly salt crystallization tests, and diagnostic methodology used; (ii) salt decay processes, namely, influence of soluble salts on drying, mechanisms of salt-induced dampness and salt distribution in masonry; (iii) reasons for sodium chloride being typically much less damaging than sodium sulfate in laboratory tests; (iv) influence of factors such as the type of salt, kind of substrate material or presence of a paint layer on the behaviour of plasters and renders; (v) factors that can account for a worsening of salt damage after restoration interventions; (vi) field or application conditions that favour salt damage.

A ação dos sais solúveis e humidade nos edifícios antigos é uma causa frequente da sua degradação. Pretende-se com este trabalho estudar experimentalmente, através de ensaios laboratoriais, de que forma diferentes tipos de sais dissolvidos em água influenciam a absorção por capilaridade em materiais porosos. O levantamento do estado da arte incidiu sobre a ação de degradação dos sais solúveis sobre os materiais porosos, sobre as características dos materiais porosos e foca também os mecanismos de transporte da água, no estado liquido e de vapor, envolvidos nos processos de absorção capilar e secagem. A campanha experimental realizada incluiu o ensaio de absorção por capilaridade e o ensaio de secagem. Os materiais porosos utilizados foram o tijolo e a argamassa e utilizaram-se seis soluções salinas, de concentração saturada: cloreto de sódio, sulfato de sódio, cloreto de potássio, nitrato de sódio, nitrato de potássio e carbonato de sódio. Realizaram-se os mesmos ensaios com água, que serviram como referência. Esta dissertação permitiu tirar conclusões sobre: i) a influência dos sais na absorção por capilaridade; ii) processos de degradação, influência dos sais solúveis na secagem de materiais porosos; iii) a correlação existente entre a degradação dos materiais porosos com o tipo de sal.

Although Portuguese azulejos are such an important heritage asset, having been extensively studied from the Art Historian viewpoint, the knowledge concerning the raw materials used and the details of the technological manufacturing process is very limited. The research project behind this dissertation was aimed at improving the present knowledge as concerns the composition of the blue pigment used in the 17th and 18th centuries. A representative set of azulejos spanning at least 200 years from ca. 1600 to 1800 was selected and the composition of the blue colour in their glazes analysed. The results were assessed aiming to answer the following main questions: i- What are the characteristic compositions of the colour (pigment and impurities) and how do they relate with the chronology of the azulejos? ii- What are the compositional traits that bear on the shades of the blue colour? iii- Can Portuguese azulejos be separated from Dutch and Spanish productions, at times when they co-existed in Portugal, solely by the composition of the blue colour? iv- Is the composition of the blue colour related with provenance of azulejos within Portugal? v- Are there grounds to suspect that at some time the Portuguese used, besides the well-known German zaffre, alternative sources of blue colour imported through their wide sea trade routes?

The presence of moisture inside a material whose surface was treated with a water repellent agent may give rise to unwanted side-effects. Indeed, the temporal and spatial significance of moistening events may be intensified if a water-repellent, as any other kind of treatment, hinders drying. This effect can be particularly relevant for historical buildings, where moisture from varied origins is recurrently present in the masonry, but is also pertinent for more recent constructions since water often finds ways to penetrate the building elements, through cracks or joints. This article discusses the application of water repellent treatments on ceramic brick, with regard to drying of the masonry. The influence of cracks parallel or perpendicular to the surface is taken into account. Five silicone-based treatments were studied. The treated or untreated material was subjected to capillary absorption tests by which the effectiveness of the water repellent effect was estimated, as well as water vapour permeability tests and drying tests. The effectiveness of four out of the five treatments is high. Vapour permeability is not much affected in one case, when the cracks are parallel to the surface, and in none of the cases, when they are perpendicular. Nonetheless, drying is significantly delayed by any of the five products, both in the case where the cracks are parallel to the surface as when they are perpendicular.

A presente dissertação visa avaliar a eficácia de dois modificadores de cristalização com baixa toxicidade quando em aplicados em dois materiais porosos, contaminados com dois tipos de sal. Foram testados o ácido cítrico e o ácido fosfocítrico, aplicados por absorção capilar ou por pulverização, em provetes de argamassa de cal aérea ou pedra de Malta saturados com soluções salinas de cloreto de sódio ou sulfato de sódio a 10% (percentagem ponderal). Foi efectuada uma análise macroscópica do efeito dos dois modificadores, baseada em ensaios de secagem. A pesquisa do estado-da-arte incidiu sobre as características dos materiais porosos, transporte de água, sais solúveis e modificadores de cristalização. Na campanha experimental foram ainda realizados ensaios de caracterização da argamassa fresca, da argamassa endurecida e da pedra de Malta utilizadas. Determinaram-se também as características de porosidade, permeabilidade ao vapor de água, tensão superficial e evaporação das soluções, capilaridade e secagem. O trabalho realizado permitiu conhecer os principais desenvolvimentos recentes sobre modificadores de cristalização e concluir sobre a influência na secagem e a relevância dos dois modos de aplicação testados do ácido cítrico e do ácido fosfocítrico.

A acção dos sais solúveis é uma causa frequente de degradação dos edifícios antigos, reflectindo-se a vários níveis (e.g., estético, habitabilidade, segurança estrutural). Esta dissertação tem como objectivo efectuar a análise e sistematização de um leque abrangente de práticas actualmente utilizadas para controlo da degradação por sais solúveis. Neste âmbito, foi utilizada a análise documental de bibliografia posterior a 2000 e procedeu-se à análise crítica de métodos de controlo da degradação seleccionados: remoção mecânica de eflorescências; remoção de materiais contaminantes; compressas; remoção electroquímica de sais; microrganismos; modificadores de cristalização; rebocos; controlo ambiental; controlo da humidade ascensional; método do hidróxido de bário. Analisaram-se também algumas medidas práticas para prevenção do risco de ocorrência ou agravamento desta degradação. Adicionalmente, avaliou-se a complementaridade entre métodos, identificando eventuais benefícios de uma acção conjugada. A sistematização das práticas analisadas envolveu o seu enquadramento segundo três abordagens distintas: prevenção, correcção, e mitigação. A dissertação permitiu tirar conclusões sobre: (i) a actuação face à degradação provocada por sais solúveis, a qual deve pautar-se por uma compreensão global do problema; (ii) a importância das medidas preventivas, como meio para evitar os danos e custos associados; (iii) a relevância dos métodos de controlo da degradação, nas vertentes correctiva e de mitigação; (iv) a experiência actual sobre a utilização prática dos métodos em edifícios, designadamente com relação ao número de casos de estudo existentes; (v) a necessidade de uma boa compreensão das práticas referidas, nomeadamente em relação às vantagens e inconvenientes, a qual pode ser facilitada pela sua sistematização.

Estudou-se um conjunto de fragmentos de azulejos datados do século XVII, de produção portuguesa, cedido pelo Museu Nacional do Azulejo. O objectivo foi caracterizar morfológica e quimicamente a camada pictórica da azulejaria portuguesa do século XVII. O estudo utilizou uma abordagem multi-analítica, incluindo a espectrometria de fluorescência de raios X dispersiva de energias (µ-EDXRF), espectroscopia de Raman, o microscópio electrónico de varrimento com microanálise de raios X (SEM-EDS), e técnicas de observação incluindo o SEM e microscopia óptica. A azulejaria portuguesa do século XVII caracteriza-se por uma paleta cromática relativamente rica, que engloba o azul, amarelo, laranja, verde, púrpura, um tom púrpura acastanhado e ainda outro castanho muito escuro utilizado em contornos. As cores integram um fundo branco – o vidrado estanífero característico da majólica. Confirmou-se que o azul se deve ao óxido de cobalto, o púrpura ao óxido de manganês e um dos verdes, de aparência transparente, ao óxido de cobre. Os resultados indicam que o amarelo será uma variante do pigmento amarelo de Nápoles (antimoniato de chumbo), constituído por um óxido triplo de Pb-Sb-Zn. As outras cores são obtidas através de misturas: o laranja resulta da adição de hematite ao pigmento amarelo, o verde-seco resulta da adição de óxido de cobalto também ao pigmento amarelo, e os vários tons entre púrpura e castanho resultam da mistura de hematite com óxido de manganês em teores variáveis. Observaram-se morfologias distintas das cores: o amarelo, laranja e castanho-escuro permanecem à superfície do vidrado e conferem-lhe cores opacas. O azul, o verde-cobre e o púrpura difundem no vidrado em profundidade e, por vezes, horizontalmente. Os seus óxidos dissolvem-se na matriz vítrea, obtendo-se uma cor transparente. Com o verde-seco ocorre uma separação dos componentes da cor, na medida em que as partículas de pigmento amarelo permanecem à superfície, enquanto o azul difunde no vidrado.

A presente dissertação tem por finalidade compreender a influência dos tratamentos hidrófugos na secagem do tijolo cerâmico, tendo assentado na realização de ensaios de absorção capilar, permeabilidade ao vapor de água e secagem. Foi inicialmente avaliada a possibilidade de utilização de tijolo cerâmico maciço de três proveniências distintas. Uma destas origens foi a Praça de Touros do Campo Pequeno, em Lisboa, que permitiu estudar quatro tipos distintos de tijolo antigo. As outras duas origens foram as cerâmicas Torreense e de Vale de Gândara, tratando-se portanto neste caso de tijolos de fabrico recente. Os diferentes tipos de tijolo foram caracterizados quanto à sua aparência, morfologia, teor de sal, absorção capilar e comportamento em secagem. O tijolo de Vale de Gândara foi o tipo seleccionado para a aplicação dos tratamentos hidrófugos. Foi detectada a presença de fissuras neste tipo tijolo, tal como em todos os outros tipos caracterizados. Sendo este defeito relevante para o transporte de humidade, foi necessário ter em consideração a influência da orientação preferencial das fissuras. Assim, utilizaram-se em todos os ensaios provetes com fissuras paralelas e provetes com fissuras perpendiculares à superfície. Estudaram-se cinco tratamentos hidrófugos com base em silicone. Foram realizados ensaios de absorção capilar através da face tratada, ensaios de permeabilidade ao vapor de água e ensaios de secagem (método RILEM da curva de evaporação). Realizaram-se ensaios semelhantes sobre o material não-tratado, que serviram como referência. Os resultados do ensaio de absorção capilar indicam que a eficácia de quatro dos tratamentos é elevada, sendo a secagem do tijolo significativamente dificultada por esses quatro produtos. Verificou-se, no entanto, que o decréscimo da permeabilidade ao vapor apenas é significativo para três hidrófugos. A influência dos hidrófugos na permeabilidade ao vapor apenas é mensurável no caso dos provetes com fissuras paralelas à base. Quando as fissuras são perpendiculares à base, a permeabilidade ao vapor é bastante mais elevada, não sendo afectada pelo hidrófugo.

A presente dissertação visa compreender a influência dos revestimentos por pintura na secagem de materiais de construção porosos, tendo focado a nível experimental o caso dos substratos constituídos por uma argamassa de cal aérea. Aborda-se, em particular, o caso dos edifícios antigos e, mais especificamente, a situação das paredes com teor de humidade não desprezável que é muito corrente neste tipo de edifícios. O levantamento do estado-da-arte incide sobre as características dos materiais porosos, em particular as argamassas de cal aérea, e de diferentes tipos de revestimentos por pintura indicados para este tipo de utilização. Foca também os mecanismos de transporte de humidade envolvidos nos processos de secagem. Efectuou-se uma pesquisa de mercado e um inquérito ao meio técnico com o objectivo de perceber quais os revestimentos por pintura usados em intervenções de reabilitação / conservação e, assim, avaliar a situação da prática em Portugal. A campanha experimental a seguir realizada incluiu ensaios de permeabilidade ao vapor de água, de absorção capilar e de secagem e incidiu sobre dezasseis revestimentos por pintura disponíveis no mercado português. Treze destes revestimentos são tintas de silicatos, de silicone ou de pliolite que os respectivos fornecedores indicaram serem apropriadas para aplicação em paredes com problemas de humidade. Ensaiaram-se ainda duas tintas de cal de fabrico industrial e uma “tinta plástica” que serviu como referência. A dissertação permitiu obter dados sobre o estado-da-prática em Portugal, em particular no que se refere aos tipos de tintas usados em paredes de edifícios antigos com teor de humidade não desprezável. Permitiu também retirar conclusões sobre: (i) a influência dos revestimentos por pintura na secagem, na absorção de água por capilaridade e na permeabilidade ao vapor de água; (ii) a influência que o estado de humidificação do suporte pode ter no comportamento dos revestimentos; (iii) a correlação existente entre o comportamento à secagem (índice de secagem) e a permeabilidade ao vapor de água, que é a característica correntemente utilizada para prever o desempenho dos revestimentos.

A realização de auditorias pré-demolição a edifícios requer o envolvimento de várias partes interessadas, desde o proprietário, ao projetista e ao empreiteiro, com vista a maximizar a recuperação de materiais e elementos construtivos e minimizar a quantidade de resíduos de construção e demolição, de modo a impulsionar a economia circular no setor da construção. Estas auditorias devem ser realizadas antes do projeto de demolição ou reabilitação do edifício, de acordo com recomendações comuns. Para a realização dessas auditorias, foi desenvolvido este Guia Português para Auditorias Pré-Demolição e uma ferramenta em Excel com modelos padrão para a realização de um inventário aos recursos presentes no edifício. O inventário teve como base as orientações da União Europeia e do Quadro comum da União Europeia de Edifícios Sustentáveis

Os resíduos de construção e demolição (RCD) representam 46% do total de resíduos produzidos na Europa, cerca de 820 milhões de toneladas por ano, ou 5190 kg per capita. Vários constituintes dos RCD são potencialmente reutilizáveis e recicláveis, o que foca a atenção no seu papel relevante na promoção dos princípios da economia circular no setor da construção, na fase de fim de vida. Este enquadramento conceptual visa reunir as melhores práticas dos diferentes países relativamente à aplicação de auditorias de pré-demolição em edifícios como uma ferramenta útil para o desenvolvimento do guia português. É também abordada a necessidade de minimizar a geração de resíduos contaminados, durante a demolição ou reabilitação de edifícios, como um caminho relevante para maximizar a reutilização e reciclabilidade dos RCD e a qualidade dos materiais recuperados. Para este efeito, é apresentada uma lista de substâncias perigosas críticas e feita a identificação dos materiais de construção que potencialmente contêm constituintes perigosos. Neste relatório é descrita a atividade desenvolvida na tarefa T2

Foi fabricado um betão com agregados de minério de ferro proveniente de jazida de Moncorvo, para avaliação do potencial destes agregados para o fabrico de betão de elevada densidade. Com base nos resultados obtidos são feitas considerações sobre a densidade do betão que será possível obter em função da massa volúmica do agregado.

The research project DRYMASS – Drying of porous building materials possibly contaminated with soluble salts (PTDC/ECM/100553/2008) took place from February 2010 to January 2014. The project allowed advancing the knowledge on drying of porous building materials, as well as about how soluble salts and some types of surface layers affect that behaviour. A new method to characterize salt decay processes by optical profilometry was proposed, and the usefulness of NMR to clarify the causes of such processes demonstrated. There was also a provisional patent application, which was based on research results about the influence that lime coatings have on drying. The main findings of the project were specifically the following. Lime coatings may accelerate the drying of porous substrates. Also due to their high drying rate, ordinary building materials have a high evaporative cooling potential. With salt solutions, the drying kinetics of porous building materials is slower than with pure water. One of the causes is the reduction in sorptivity. Occasionally, there is also obstruction to vapour transport by the efflorescence. However, in most cases, porous efflorescence occurs, which pose no obstruction to this transport. Further, fissures or disaggregation may accelerate drying. Soluble salts amplify the effects that the natural heterogeneity of porous materials has on the drying kinetics. Due to the chaotic nature of the process, lime coatings will not necessarily enhance drying in this case. Sodium sulfate can be very destructive in the absence of high temperature or successive wet/dry cycles. A delamination pattern similar to those found in real constructions was observed on the well-known Ançã limestone. NMR showed that mirabilite and heptahydrate can both be responsible for this delamination pattern, in different conditions. Thermal expansion may be one of the mechanisms involved in salt decay processes.

In this report we describe an experimental study carried out at LNEC within the research project DRYMASS (ref. PTDC/ECM/100553/2008). The study was aimed at evaluating the possibility of increasing the drying rate of porous building materials by means of nano-treatments. It was justified by previous results of other authors that observed an apparently unexplainable increase in the evaporation rate of natural stone after application of nano-calcium hydroxide solutions as consolidating agents. Two commercial treatments, consisting on alcoholic or aqueous suspensions of nano-lime or nanosilica, respectively, were tested on three porous building materials. The treatments are generally used for consolidation. The materials were a lime mortar and two natural stones (Ançã limestone and Bentheimer sandstone). It was concluded that neither of the nano-treatments hinders drying. However, they were also not able to increase the drying kinetics of any of the three substrates.

The decay of porous building materials due to salt crystallization is very frequent and often significant in the built heritage and, thus, a proper understanding of the underlying processes has major importance for conservation. In this light, a new method for characterization of salt decay processes was developed within the DRYMASS research project, which is based on continuously measuring by optical profilometry the micrometric changes that occur on the material surface during drying. This method produces three different types of output: the so-called "alteration curve", as well as the current gravimetric evaporation curve and time-lapse photographs of the decay. But the three features had, until now, to be recorded using different specimens. This is an important limitation because the high uncertainty of salt decay processes may give rise to different decay patterns in similar specimens. Here, we present a development of the original study, which was afterwards carried out within the same project to allow evaluating the three features in a single specimen, by using an integrated set-up. This new study was carried out with two salts often found in salt decayed constructions, Na2SO4 and NaCl, and a material frequently used in the architectural heritage, Ançã limestone. Some of the experiments were performed after application of a water repellent treatment on the stone.

This is the third progress report of the research project "DRYMASS - Drying of porous materials possibly contaminated with soluble salts". It includes the following main sections: (i) A summary of the work, which briefly describes the activities undertaken in the reporting period and the results achieved, referring specifically to the tasks under execution in that period. (ii) A justification of the deviations from the Approved Proposal, both from a scientific or financial viewpoint. It also identifies the major difficulties in implementing the approved work plan, and how they will be overcome. (iii) A list of publications. It includes also the following annexes: Annex I – 2nd reformulation proposal with updated timeline; Annex II – Cryspom III - Book of abstracts and conference program; Annex III – Summary report on Cryspom III; Annexe IV – Figures and abstracts; Annexe V – Article submitted to Transport in Porous Media.

Conserving the built heritage today entails decisions and planning at several different levels. Firstly, analysis is necessary regarding what to conserve: values, authenticity and integrity are the key concepts at this macro level. Then, decisions on how to conserve them should consider the chief principles of good conservation practice, among which compatibility, retreatability and minimum intervention are prominent today. This report analyses these concepts and the different ways in which they were translated into the decision support systems that are nowadays resorted to, from values-based decision making and risk management in conservation to intervention planning and performance assessments. The ultimate goal of this analysis is to compile tools that promote a more rational decision making in conservation.

Este relatório sintetiza a atividade desenvolvida no LNEC visando contribuir para a aplicação dos materiais obtidos no processamento de resíduos de construção e demolição (RCD) no sector da construção, nomeadamente em betões e argamassas, em pavimentos rodoviários e em aterros e camadas de leito de infraestruturas de transporte. Esta atividade abrange as áreas de investigação programada, de investigação por contrato e outras atividades científicas e técnicas das quais se destaca a preparação de especificações técnicas específicas para estes materiais, a difusão de conhecimentos através da realização de ações de formação, da elaboração de documentos e da participação em conferências e outras reuniões científicas e técnicas. Nesta atividade integra-se também a cooperação com entidades, nacionais e estrangeiras, designadamente com universidades e associações de carácter científico e técnico. Sendo esta uma atividade transversal no LNEC O presente relatório integra o trabalho desenvolvido no Departamento de Materiais, no Departamento de Edifícios, no Departamento de Geotecnia e no Departamento de Transportes.

A empresa Repsol Polímeros, Lda, através de correio electrónico no dia 6 de Abril de 2011, solicitou ao Laboratório Nacional de Engenharia Civil (LNEC) a avaliação do estado de degradação de estruturas do Terminal Portuário do Porto de Sines, que incluíam dois viadutos localizados entre os postos de acostagem 4/5 e 9/10 da Área do Porto de Sines (APS)1 e o porto-cais do terminal de Graneis Líquidos2, e a apresentação de recomendações relativas à solução a adoptar para a recuperação das estruturas.

O Laboratório Nacional de Engenharia Civil tem vindo a desenvolver um estudo no domínio da conservação dos azulejos históricos que permitiu, nalguns casos relevantes, estabelecer uma ligação entre determinados defeitos de fabrico e formas específicas de degradação. Esse estudo demonstrou a conveniência no estabelecimento de um glossário ilustrado, incluindo defeitos de fabrico e formas de degradação e contemplando alguma terminologia nova. É esse trabalho, saído de uma colaboração com o Museu Nacional do Azulejo, que agora se apresenta num vocabulário que inclui também algumas definições básicas, cobrindo termos necessários às definições subsequentes de defeitos de fabrico e de formas de degradação. Os termos em relação aos quais pareceu aos autores poderem subsistir dúvidas têm anexas ilustrações exemplificativas.

N/A

N/A

N/A

N/A

This paper delivers actionable recommendations towards building a rationale for activating and promoting Underground Built Heritage (UBH) based on the nexus heritage, territory and society, and making use of existing literature and findings from five international cases. The research was conducted in the framework of the working group on Planning Approaches of the COST Action Underground4value. The analysis of the cases aims to provide guidelines for this working group and to benchmark good practices in activating UBH. It highlights the importance of community-led initiatives, leadership and dialogue and power sharing between the local/regional authorities and communities aiming for better understanding of the potential of UBH. The successes and/or failures of the five cases emphasise the importance of knowledge and experience in participatory approaches. Success was verified, when effectiveness and democratic principles were combined in the planning process, and local history is integrated with citizen science, co-creation and placemaking. The analysed approaches stimulate a new hybrid layer for activating UBH, provide mechanisms of mediation between people and heritage, and contribute to cultural and social dimensions of sustainability. This is a highly challenging endeavour, as it seeks to support and advance a sound understanding of UBH as a sustainable resource, backed by strategic stakeholder dialogue and contextual knowledge. Such effort requires a dynamic understanding of UBH values, knowledge, abilities and skills, towards creating more effective coalitions of “actors” within localities, by developing structures, which encourage long term collaborative relationships.

N/A

A caracterização dos materiais históricos e a identificação do respetivo estado de conservação engloba um corpus de conhecimento teórico, prático e metodológico essencial para a conservação e o restauro do património cultural arquitetónico e arqueológico. Refletir sobre os materiais históricos para intervir no património requer, pois, contemplar a variedade de materiais a partir das suas múltiplas facetas, reivindicando uma perspetiva pluri e interdisciplinar na elaboração do conhecimento científico. Requer também aprofundar o estudo das tecnologias e materiais tradicionais, o que contribui para densificar o campo de conhecimento sobre o património e, cientificamente, definir os requisitos de compatibilidade e eficiência dos novos materiais, paralelamente colaborando para a salvaguarda do saber técnico tradicional.

O artigo trata de uma síntese de resultados do Congresso Ibero-Americano “Património, suas matérias e imatérias”, LNEC, Lisboa, 2-3 de novembro de 2016, constituindo-se um artigo de noticías.

O tabalho faz uma apresentação crítica do Livro " A supremacia do Pedestre", da autoria de Fábio Fonseca e Antonio Colchete Filho, tendo o Livro sido editado pela UNALFA: Editora da Unviersidade FEderal de Juiz de Fora, Minas Gerais, Braisl.

É analisada uma amostra de betonilha para determinação do teor de cimento. As análises incluíram a realização de ensaios de resistência à compressão, termogravimetria e químicos.