Publications

This study evaluated the durability of three innovative multilayer insulation systems incorporating thermal mortars with EPS aggregates and silica aerogel granules after hygrothermal accelerated aging and one year of natural aging at an urban site in Portugal. The loss of performance was assessed after the accelerated aging and every three months of natural aging using non-destructive testing. Chemical-morphological analyses were alsocarried out prior to and after accelerated and natural aging. Results obtained after accelerated and natural aging were compared, thus contributing towards a deeper understanding of possible synergistic effects of several degradation agents and mechanisms on the long-term durability of multilayer insulation systems. The Coffin-Manson equation showed that the accelerated aging procedure (~13 days of heat/rain cycles and 5 days of heat/cold cycles) adopted herein corresponds to approximately 11 years of natural aging in typical urban conditions. The results show a significant increase in capillary water absorption and drying capacity after aging.Extensive surface microcracking was observed after accelerated aging and after 3 months of natural aging, especially in the systems facing North. Traces of biological growth were detected on both the artificially and naturally aged systems, whereas aesthetic alterations were more pronounced in North-oriented specimens after 3 months of exposure, with significantly lower surface gloss and a darker tone. On the other hand, color change cannot be detected in the artificially aged systems (

The internal structures and the hygroscopicity of bio-based boards consisting of giantreed (Arundo donax L.) and hazelnut shells as bio-aggregates, and a sodium silicate solution asthe adhesive, were investigated. The aim was to evaluate the influence of each material (the bio-aggregates and adhesive) and their distributions in the boards on the final performance. By carrying out X-ray computed tomography, the internal structures and the porosities of the boards were determined, allowing important considerations of their hygroscopicity. The voids

ETICS are multilayer building solutions applied to the building external walls to provide animproved thermal performance to the building envelope. However, several questions have beenraised concerning the durability of ETICS, namely related to biological colonisation phenomena.Considering the high susceptibility of ETICS to bio-colonisation, the following research questions arise: (i) what is the impact of surface temperature (ST) and surface relative humidity (SRH)fuctuation on mould growth in ETICS facades? (ii) is it possible to predict mould growth onETICS under fuctuating conditions considering favourable and unfavourable growth conditions?This study aims to investigate the infuence of the hygrothermal behaviour of five different ETICS(with thermal mortars and insulation boards) on mould growth. ETICS were exposed for one yearat an urban site in Lisbon, Portugal, facing North, during which the ST and the SRH weremonitored. Concurrently, numerical simulations were performed to evaluate the hygrothermalbehaviour of the ETICS. Three theoretical indices were applied, using numerically and experimmentally obtained values of ST and SRH as input to provide an indication of the risk of mould growth. The results were complemented and validated by assessing the bio-colonisation, water performance and aesthetic properties of the ETICS. Index 1 (percentage of time with SRH

The introduction of stored product insect pests to new areas is facilitated by food trade among countries, and effective detection and monitoring programs are crucial for food security. The khapra beetle, Trogoderma granarium Everts is one of the most destructive insect species. In Portugal, T. granarium has been detected in 1988. However, no new data has been added to this information since that date. Floor traps with pheromones specific to T. granarium were used and placed inside ports, mills, and storage facilities, including warehouses and silos, between June and September in 2017, 2019, 2021, and 2022.Previous results from other sampling programs conducted between 2002 and 2008 are also referred here to add more evidence for the presence or absence of T. granarium in Portugal. Here, various types of traps, including some generalists and others with pheromones (such as T. granarium), were used. The collected insects were identified to species, or genus.Surveys conducted identified approximately 40 insect species that are associated with stored products, in a total of 23.725 insects, and among them, the weevils belonging to the genus Sitophilus C.J.Schoenherr have been recognized as the main pests that affects stored cereals. Regarding the surveys made between 2017 and 2022 and previous surveys done in Portugal (between 2002 and 2008; n = 26.719 insects identified), no T. granarium individuals were detected in any of the entomological samples, and only a few Dermestidae specimens were found across all surveys, one of them belonging to the same genus, identified as Trogoderma inclusum LeConte. With the predicted changes in climate, there is a risk of introducing T. granarium and other destructive insect pests that could displace itophilus weevils as the key stored products pest in Portugal. Therefore, it is crucial to monitor and implement measures to prevent the spread of invasive pests for effective pest management and food security purposes, using proper trapping methods and accurate and rapid identification tools.

Arundo donax (giant reed or giant cane) is a widely available, perennial, invasive, non-food crop, present worldwide and employed for several uses, including building practices. Considering the increasing demand for sustainable building materials, A. donax can be an eficient solution. This study investigated its properties as a bio-aggregate mixed with a sodium silicate solution as an adhesive. A horizontal analysis that provided a general characterization of the composite was carried out. The results showed that the A. donax-based composite had anapparent density of 517 kg/m3 , thermal conductivity of 0.128 W/(m.K), and high hygroscopicity, with a moisture buffering value of 4.33 g/(m2 %RH), property that could be both an advantage for indoor comfort and a drawback. The uncommon sound absorption behaviour can be comparable to granular materials, with the highest sound absorption coeficient values,

Arundo donax (giant reed or giant cane) is a widely available, perennial, invasive, non-food crop, present worldwide and employed for several uses, including building practices. Considering the increasing demand for sustainable building materials, A. donax can be an efficient solution. This study investigated its properties as a bio-aggregate mixed with a sodium silicate solution as an adhesive. A horizontal analysis that provided a general characterization of the composite was carried out. The results showed that the A. donax-based composite had an apparent density of 517 kg/m3, thermal conductivity of 0.128 W/(m.K), and high hygroscopicity, with a moisture buffering value of 4.33 g/(m2 %RH), property that could be both an advantage for indoor comfort and a drawback. The uncommon sound absorption behaviour can be comparable to granular materials, with the highest sound absorption coefficient values,

The search for innovative and sustainable solutions to improve the energy efficiencyof the construction industry has been a hot topic for researchers due to the tremendous impactof insulator materials in the thermal comfort of buildings. In the present work, an innovativelightweight composite material with thermal insulation properties was developed, for the firsttime, by using cardoon particles and polyurethane. The formulation of the composite materialwas optimized in terms of cardoon fraction and the polyol/isocyanate ratio, to achieve the bestcompromise between internal bond (IB) strength and thickness swelling (TS). The best performing composite was PU75-CP45, with 45 wt% of cardoon particles and 75% of isocyanate, achieving an IB of 0.41 MPa and a TS of 5.3%. Regarding insulation properties, the PU75-CP45 composite material exhibits a promising performance when compared to conventional construction industry materials by tuning its thickness. Additionally, the composite material presented very low emissions of volatile organic compounds and formaldehyde (bellow to legislation levels) and high resistance to biological degradation

External Thermal Insulation Composite Systems (ETICS) are frequently used to enhance the energy efficiency of the built environment. However, stains of presumable biological nature are often detected shortly after application, causing cladding defacement and altering the building aesthetics. To address which microbiota could contribute to these biodeterioration related color/aesthetic anomalies, samples collected from stains detected on the surface of building facades with ETICS in three residential sites in Lisbon, Portugal, were analyzed throughmicrobiological culture-dependent technique and culture-independent amplicon DNA high throughput sequencing taxonomic profiling. The obtained data provided a comprehensive description of microbial communities assigned to diverse taxa of the major microbial groups of heterotrophic bacteria, fungi, cyanobacteria, and microalgae (through DNA plastid detection) in the sampled stains. Based on that, we propose that new microorganisms could be added to the list of bio-susceptibility testing organisms in ETICS. Furthermore, microbiota diversity depended more on facade location and cardinal orientation than on ETICS material composition. Overall, this study reveals the unique microbial communities of color/aesthetic biodeterioration stains in ETICS facades, unlike those of other surfaces, and the associated environmental dynamics.

Laboratory tests were carried out to evaluate the feasibility of producing boards or coating panels with good hygrothermal performance by using different agro-industrial wastes (grape and olive press wastes, hazelnut shells, spent coffee and pine) and adhesives (gypsum-based binder, sodium silicate solution and starch-based glue). Hygrothermal properties and resistance to mould growth, including the effect of citric acid, were evaluated. The results highlighted the benefits and drawbacks of each adhesive: the binder seems more adequate to produce bio-based plastering mortars than boards; the other adhesives seem efficient solutions to produce boards with good hygrothermal properties; for the natural glue the bio-susceptibility needs improvement.

Traditional carpentry joints can be found worldwide in many timber truss structures connectingrafter and tie beam. One failure mode of this connection result from shear in the tie beam beyond the notch either due to bad design or deterioration. In this article, the reduction in shear strength of Single Step Joints (SSJ) resulting from biological attack by anobiids was analysed. For this purpose, tests were carried out in non-degraded scots pine (Pinus sylvestris L.) specimens (reference) and compared to artificially degraded specimens with three different levels of degradation. The reduction of shear resistance was analysed in relation to the density of holes drilled during the degradation simulation, the loss of mass, and the reduction of the hearresistant area. At lower degradation levels, no significant reduction in shear strength was observed. On the other hand, the linear regression shows a trend of resistance reduction with increasing degradation. Despite the relatively low coefficient of determination (r2 = 0.25), the parameterthat best correlated with the residual strength was the reduction in the shear-resistant area.

Em Portugal existe um património muito significativo no que se refere a pontes metálicas ferroviárias e rodoviárias, muitas das quais constituem já um legado histórico apreciável. Há, portanto, não só que continuar a preservar este património histórico mas também garantir que as pontes mais recentes possam vir a apresentar desempenhos idênticos ou mesmo superiores. Nesta comunicação, após um enquadramento histórico da evolução nos processos siderúrgicos e sua correlação com a construção metálica em especial de pontes metálicas, faz-se uma sistematização dos principais processos de degradação do aço estrutural e das causas dos danos mais frequentes nestas estruturas, e apresentam-se as técnicas que podem ser utilizadas durante a manutenção em serviço destas pontes, para a identificação e avaliação dos danos existentes, e os métodos de reparação/protecção adequados aos danos mais frequentes.

O género Acácia inclui numerosas espécies, algumas economicamente importantes, que ocorrem naturalmente em zonas áridas na Austrália, Ásia, África e América.Em Portugal espécies deste género foram introduzidas no início do século XX, em solos secos e arenosos ao longo da costa. A Acacia melanoxylon apesar de bem adaptada às condições ecológicas do país, não tem sido aproveitada, em parte devido ao desconhecimento das suas propriedades.A densidade é considerada a mais importante propriedade da madeira por estar correlacionada com outras propriedades. Apesar de ser fácil de determinar, requer mão-de-obra intensiva e é demorada. O desenvolvimento de técnicas expeditas e não destrutivas como a espectroscopia de infravermelho próximo (NIR) permite a avaliação extensiva de um grande número de amostras com um custo muito inferior.Neste trabalho desenvolveu-se um modelo para estimar a densidade básica na madeira de Acacia melanoxylon por NIR. A validação do modelo com amostras independentes mostrou um coeficiente de determinação elevado (R2=0,90) e um erro baixo (RMSEV=16,7 kg/m3).

Os perfis tubulares de aço de secção elipsoidal oca fornecem uma nova solução com bastantes potencialidades estéticas e características estruturais interessantes. Contudo, existe ainda pouca informação disponível para o cálculo deste tipo de perfis, nomeadamente ao nível das disposições normativas adoptadas nos regulamentos de cálculo de estruturas de aço. A fim de colmatar uma destas lacunas, o presente trabalho propõe um critério analítico para o cálculo dos esforços resistentes de secções elipsoidais ocas de aço totalmente plastificadas, submetidas a um esforço normal e a flexão segundo um dos seus eixos principais de inércia. Este critério é também aplicável ao caso particular dos perfis tubulares de secção circular oca.

Este trabalho aborda a resistência de prumos telescópicos extensíveis de aço submetidosa compressão axial. Como o dimensionamento destes elementos envolve frequentemente níveisde incerteza elevados, foi decidido realizar uma série de estudos numéricos e experimentais paracompreender melhor o seu comportamento estrutural. Com base nos resultados obtidos foi possíveldesenvolver uma curva de dimensionamento específica para este tipo de elementos estruturais,contribuindo-se assim para ultrapassar algumas das limitações actualmente existentes nas normasrelativas ao respectivo projecto.

The detection in 2002 of drywood termites in the islands of Azores has became an urgent issue tobe coped with given the fast degradation that structural elements can show after a short period ofinstallation of a colony. A recent study indicates drywood termite presence in about half of thebuildings of the historic centre of Angra do Heroísmo (a World Heritage site) in Terceira Islandand timber structures surveys conducted so far points to strong levels of degradation of timberelements and structures.A strong effort should be put on the rehabilitation of structures already affected, implementationof control procedures for restraining the spread of new colonies into so far sound buildings andalteration of traditional practices (namely choice of wood species and protection treatments)regarding timber utilization in construction.This document presents some of the most relevant facts regarding drywood termites

Wood modification by sol-gel treatments shows many positive features, like antimicrobialproperties. Wood was also successfully modified with alkoxysilanes enhancing its resistanceagainst soil micro-organisms. Silver, copper, zinc compounds, boric acid or organic biocidessuch as alkylammonium compounds may be added to the sol-gel to enhance its biocidalproperties. Nevertheless, if some of these active ingredients and compounds are not fixed intowood by chemical reactions, they can be easily leached out by water. To overcome thislimitation, a system based on silica sol-gel material starting from alkoxysilanes has beenfunctionalized with organic groups having copper linking function. Sol-gel was also coupledwith boric acid. As preliminary tests against the brown rot agent Coniophora puteana(Schumacher ex Fries) gave good results, the sol-gel formulations were also tested for theirefficacy against subterranean termites. A no-choice test was set up, in two different time scales.Results show that though the sol-gel treatments act in very different ways, all of them areefficacy against subterranean termites. The total mortality occurred in the longer test suggestedthat active ingredients may be added in lower quantity.

Refere-se o presente texto à manutenção / reabilitação de elementos estruturais de madeira em edifícios antigos quando local e medianamente degradados por fungos de podridão, segundo o processo da consolidação por impregnação de produtos poliméricos.Apresenta-se o trabalho de investigação laboratorial desenvolvido sobre provetes de pinho bravo com diversos níveis de degradação por fungos de podridão cúbica, nos quais foram aplicados cinco produtos comerciais de baixa viscosidade, específicos para consolidação. As relações entre o nível de degradação da madeira (perda de massa) e a eficiência da consolidação, medida por testes de dureza estática superficial e de resistência à compressão paralela às fibras, são apresentadas, tratadas e discutidas.

This paper focuses the fire performance of timber and timber structures and discussespossible approaches to mitigate the fire risk in timber buildings, with special relevance tothe case of timber roofs.Furthermore, it highlights a number of issues concerning the implications for timberdurability and mechanical properties resulting from the exposure to fire itself and hightemperatures, active fire protection equipment and firefighting tactics, namely thoseinvolving the use of water, and passive fire protection measures, namely fire retardanttreatments. These issues need be considered by those involved in the assessment andsafeguard of ancient timber buildings.

Furfurylation was tested with maritime pine wood (Pinus pinaster Aiton,) which is themost important pine species in Portugal. The wood was treated with a furfuryl alcoholmixture (FA 70 mix) at Kebony Products DA in Norway, in an autoclave using vacuumand pressure stages and subsequently cured and dried in a vacuum drying kiln. Bothheartwood and sapwood were treated, with weight percent gains of 38% and 23%respectively. There were no significant changes on MOE and bending strength. Jankahardness increased 56% and 49%, on radial and tangential sections, respectively.Equilibrium moisture content decreased in the sapwood from 8.9 to 5.1% (at 35%relative humidity), from 12.9 to 7.3% (at 65%) and from 17.3 to 9.0% (at 85%). Inheartwood the moisture decrease was very small. The dimensional stability of sapwoodincreased with ASE35 35.6 and 41.8%, ASE65 29.0 and 43.4% and ASE85 31.4 and45.1% for radial and tangential directions respectively. The improvements forheartwood were smaller and only significant in the tangential direction and at the higherrelative humidity values: ASE65 was 12.3 and 22.4% and ASE 85 10.5 and 24.8% forradial and tangential directions, respectively.

Após o terramoto de 1755 em Lisboa a necessidade de reconstrução da cidade levou aodesenvolvimento de uma estrutura designada Gaiola Pombalina, considerado o sistema anti-sísmico maisavançado do séc. XVIII.Estas estruturas baseadas num reticulado de frontais compostos de prumos travessanhos e escoras cominterstícios preenchidos por alvenaria de pedra ou tijolo têm vindo a sofrer alterações estruturais, como porexemplo a introdução de novos materiais, podendo comprometer a acção anti-sísmica e pôr em risco o edificadoPombalino.O comportamento físico e mecânico da madeira depende da sua estrutura e daí a necessidade de avaliação dasespécies de madeira nestas estruturas. Não existe nenhum estudo sistematizado com recurso à identificaçãomicroscópica destas madeiras.O trabalho apresentado inclui a identificação anatómica das amostras de madeira de uma gaiola de um edifíciopombalino. Foram preparadas as amostras para observação à lupa e ao microscópio. Fizeram-se cortes na secçãotransversal, tangencial e radial da madeira com o micrótomo, que foram analisadas através de um sistema deanálise de imagem. Apresentam-se fotomicrografias das amostras analisadas e respectivas observaçõesmicroscópicas.Resultados preliminares referentes às amostras analisadas indicam a presença de madeira do género Pinus,género não referenciado em bibliografia na construção das Gaiolas Pombalinas.

N/A

N/A

N/A

N/A

O Museu da Academia das Ciências de Lisboa possui uma preciosa xiloteca assinada pelo Mestre dos marceneiros portugueses, José Aniceto Rapozo contendo 1213 amostras de madeiras do Brasil e 12 de outras origens. A sua importância no progresso do conhecimento dos recursos florestais do Brasil naviragem dos séculos dezoito e dezanove conduziu ao estudo em curso. Dada a devastação verificada em vastas áreas florestais brasileiras, surgem dificuldades por certas espécies poderem ter distribuiçãogeográfica diferente (com eventual extinção, geral ou localizada), por insuficiência do material de comparação, e por ambiguidade das designações comerciais.Foi possível identificar esta xiloteca como uma de quatro encomendadas a Aniceto Rapozo pelo Príncipe Regente. A análise das amostras de madeira e a informação documental mostram que a colecçãotem por base uma remessa de 5008 amostras de madeiras do Brasil enviada em 1784 para o Arsenal Real do Exército, em Lisboa, pelo Vice-Rei do Brasil, Luís de Vasconcellos e Souza.O valor científico do conjunto é evidenciado pela identificação botânica das espéciesrepresentadas. Na situação actual, a identificação das espécies florestais representadas na amostragem foiinteiramente conseguida em 14% dos casos, conseguida mas ainda por confirmar em 27%. Dado o carácter preliminar deste estudo, os seus resultados serão ulteriormente publicados com mais pormenor. Among the Lisbon Academy of Sciences Museum collection there is a valuable xylarium by theleading Portuguese master cabinet-maker José Aniceto Rapozo (1756-1824), comprising 1213 wood samples from Brazil plus 12 from elsewhere. This collection is most important since it allows us to improve the knowledge on Brazilian forest resources by the end of the eighteenth century and thebeginning of the next. This study aims to establish its historical framework and scientific value. Owing tooverexploitation and even devastation of very large forest areas in Brazil, difficulties for our study aroseeither as some species may have now a different geographical distribution (and eventually may have underwent local or general extinction), by lack of adequate comparison material, or because of ambiguityof the commercial names.Results so far obtained allowed us to recognize the xylarium as one of the four commanded Rapozo by the Regent Prince, later King João VI (1767-1826). Taking into account the wood samples analyses as well as bibliographic data it is possible to conclude that the collection was prepared from a set 3 of 5008 Brazilian wood samples sent to the Royal Arsenal in Lisbon in 1784 by the Brazil

This work collects information about laboratory tests to evaluate the properties of agro-industrial wastes used for thermal insulation building materials considering them individually and in composits. It focuses on bio-susceptibility, as one of the main aspects to consider for bio-based building products.

Innovation in structures and construction materials demands a more accurate performance analysis during the life cycle. In addition, climatic changes pose new challenges to civil infrastructures that were not so relevant in the past. In most cases, the traditional test methods cannot accurately assess the complex phenomena involved in durability. The modern and complex factors require a different approach to durability analysis. The purpose of this chapter is to present innovative durability tests on construction materials: wood; rammed earth, cob and unfired blocks; natural stone; bituminous binders and mixtures; and Fibre Reinforced Polymers (FRP) to concrete bonded connections. Most of these tests concern the accelerated simulation of the main phenomena involved in durability performance

Laboratory tests were carried out to define production parameters of innovative eco-efficient composites made up of hazelnut shells as aggregate and a sodium silicate solution as adhesive. The aim was to maximize the content of bio-aggregates and minimize the amount of adhesive, guaranteeing the feasibility of producing samples. Therefore, after preliminary testing, the percentages of hazelnut shells and the sodium silicate solution were kept constant: 70% and 30% of the total volume, respectively. However, the characteristics of the considered composites did not allow the production of uniform samples. The sodium silicate solution was not rapidly absorbed by the bio-aggregates; during the drying process, it was deposited on the bottom side of the samples. The uniformity of the samples is required to guarantee a correct evaluation of their performance and future homogeneous panels. Hence, different production parameters were investigated, such as drying at T

The durability of construction materials is a key concern and can be related to different actions such as weathering conditions outdoors enhanced by climatic change, chemical and biological attack, abrasion, and other conditions of service over time. Frequently, several actions develop simultaneously, making it difficult to reproduce in situ conditions in laboratory. Furthermore, testing to assess durability depends largely on the nature of the material itself or on the way it has been assembled with other materials. The ageing techniques to assess long-term durability performance of construction materials are based on accelerated durability tests, which include, for example, thermal stress, freeze

This paper presents an overview of research carried out to assess the bonding suitability of Portuguese timbers.Most work developed in the last decades has focused Maritime pine timber, due to its traditional use in building construction, good mechanical properties and availability. Untreated, as well as preservative treated Maritime pine have been studied, as its impregnability allows deep treatment suitable for applications in Use Classes 3 and 4.Recent results on bonding preservative treated Maritime pine wood are discussed.Preliminary results regarding other species that are becoming available in the Portuguese market are also presented, as an attempt to reduce pressure on Maritime pine timber as well as to seek more valuable alternatives for their traditional uses.

No presente trabalho apresentam-se os resultados mais relevantes obtidos num programa experimental desenvolvido no LNEC com o objetivo de caracterizar a aderência dos varões nervurados do tipo A500NR SD existentes no mercado, fundamentalmente para melhorar a modelação do comportamento dos elementos de betão armado de zonas críticas de estruturas inseridas em zonas sísmicas.O programa experimental desenvolvido pretende simular as condições de aderência existentes num varão horizontal de uma ligação viga-pilar e tem como principais variáveis varões de dois diâmetros frequentemente utilizados (16 e 25 mm), dois níveis diferentes de área relativa das nervuras (A e B) e duas classes de betão (C1 e C2), ambos representativos do betão utilizado nas construções mais relevantes.Os resultados obtidos quer nos ensaios monotónicos quer nos ensaios cíclicos apontam para um decréscimo da tensão de aderência com o aumento do diâmetro da ordem dos 10%. O aumento da área relativa das nervuras transversais traduz-se num incremento da tensão máxima de aderência da ordem dos 15%, com uma redução do deslizamento que ronda os 15%. Nesse sentido, este estudo propôs que, no caso dos varões com maior área relativa das nervuras, a tensão de aderência máxima possa variar entre 2,35 e 2,65 vezes a raiz quadrada da resistência do betão à compressão e que o patamar onde a tensão de aderência é máxima se situe entre 0,5 e 1,5 mm de deslizamento.Explorou-se também o fenómeno da entrada em cedência da armadura tendo-se concluído que, em provetes que pretendem simular as condições de aderência existentes num varão horizontal de uma ligação viga-pilar, a entrada em cedência da armadura conduz a uma redução da tensão de aderência máxima inferior a 10%, quer regime monotónico quer em regime cíclico.

O presente trabalho de investigação refere-se à conservação de elementos estruturais de madeira medianamente degradados por fungos em edifícios antigos. Propõe-se estudar a compatibilidade entre produtos de tratamento e de consolidação por impregnação, aplicados sequencialmente. A avaliação do processo foi realizada maioritariamente em laboratório e na óptica do desempenho mecânico conjunto da madeira e produtos aplicados, por intermédio de ensaios físico-mecânicos destrutivos e não destrutivos e também por ensaios mecânicos não destrutivos realizados in situ. Foram utilizados produtos comerciais, aplicando-os às espécies de madeira correntemente encontradas nos edifícios antigos da zona de Lisboa: Pinho bravo e Casquinha. Procedeu-se à avaliação mecânica de madeira nova e antiga, em estado são e degradado; ao desenvolvimento de um método de medição da profundidade de penetração de produtos de tratamento; à avaliação da capacidade consolidante de madeira degradada por produtos poliméricos fluidos e à avaliação da sua actuação conjunta, estudada com e sem envelhecimento artificial. Os resultados obtidos indicaram significativos aumentos de capacidade mecânica da madeira degradada, quando submetida a tratamento e consolidação Este trabalho desenvolve, assim, uma proposta de solução para a madeira que não se encontra sã, mas que ainda possui capacidade resistente, não necessitando, por isso, de ser removida. O processo de tratamento e consolidação promove resistência aos agentes biológicos e, simultaneamente, recuperação de alguma resistência mecânica da madeira, conferindo-lhe capacidade para continuar em serviço.

Subterranean termites from the genus Reticulitermes are an important pest ofwood in service throughout southern Europe and elsewhere. For effective termitecontrol with long term protection but minimal environmental damage, newintegrated approaches to termite management are needed. Baiting-based systemsseem to be promising non-traditional methods for termite control, targeting thecolony as a whole. However, control through baiting is only feasible when it isknown that the toxicant can be transferred to all the colonies foraging on theinfested area and also throughout each individual colony. Accordingly, the workdescribed is specifically designed to achieve a better understanding of thedistribution and delimitation of colonies within a population of Reticulitermes,with parallel insights into foraging behaviour and colony organization.Initially, the species/subspecies spectrum present within the notionalReticulitermes group in Portugal was reassessed. It was shown that Reticulitermesgrassei is the only species encountered. Foraging activity was then assessed in anexperimental woodland site over two successive annual cycles, both by thesampling of natural lying dead wood and by a standard baiting grid. R. grasseiseem to select wood with larger diameter, with an apparent preference for materialalready decayed by fungi. Both termite and fungal attack on wood seems to bepromoted by higher moisture levels, such as prevail in larger litter items andduring seasonal rains. Termites were unable to detect and direct their foragingtowards sound wood in laboratory conditions, suggesting that the network ofinfochemical signals is more complex than just volatiles emanating from soundwood. Mark-release-recapture (MRR) was used to delineate foraging groups,which were then allocated to their parent colonies by the use of microsatellitemarkers. The results suggest that resource sharing is a facultative behaviour,specifically when food is not a limiting factor for colony development. Theimplications of all these findings for bait technology and protocols are discussed,with reference to the local population ecology of Reticulitermes.

O presente trabalho apresenta um projecto de Norma Portuguesa relativo ao ensaio de dureza Vickers (HV0,2 a HV5 exclusive) de materiais metálicos, e insere-se numa série de estudos programados pelo autor, enquanto coordenador da normalização nacional no domínio dos ensaios mecânicos, físicos e não-destrutivos de materiais metálicos, a fim de actualizar as Normas Portuguesas existentes neste domínio.O texto apresentado consiste na versão final de uma proposta redigida pelo autor, na sequência dos estudos efectuados ao nível da Comissão Técnica de Normalização competente.

O presente trabalho apresenta um projecto de versão portuguesa da Norma Europeia EN 10002-1, e insere-se numa série de estudos programados pelo autor, enquanto coordenador da normalização nacional no domínio dos ensaios mecânicos, físicos e não-destrutivos de materiais metálicos, a fim de actualizar as Normas Portuguesas existentes neste domínio.O texto do projecto de revisão apresentado consiste na versão final de uma proposta redigida pelo autor, na sequência dos estudos efectuados ao nível da Comissão Técnica de Normalização competente.

O presente trabalho consiste no relatório de uma missão a Paris do signatário, na sua qualidade de coordenador da Normalização Nacional no domínio dos "Ensaios mecânicos, físicos e não-destrutivos de materiais metálicos", a fim de representar Portugal numa reunião do ECISS/TC 1a "Ensaios mecânicos e físicos de aços", encarregado dos trabalhos de Normalização Europeia neste domínio.

O presente trabalho pretende mostrar as possibilidades fornecidas pela utilização de um método de simulação no estudo da homogeneidade da fiabilidade, oferecida pelas curvas de encurvadura de colunas, de diferentes regulamentos de estruturas de aço.Através de um modelo geometricamente não linear, de que se faz uma breve apresentação e se descrevem alguns exemplos de aplicação, é feito o estudo da carga crítica de encurvadura de um perfil IPE 120, segundo o eixo de maior inércia. Os resultados apresentados referem-se a cerca de 1000 colunas diferentes, obtidas através de um método de simulação do tipo Monte-Carlo, para as quais se efectua a comparação entre os valores da carga crítica obtidos e os fornecidos por vários regulamentos, bem como a análise da homogeneidade da fiabilidade conferida pelos mesmos regulamentos em função das respectivas esbeltezas.

O presente trabalho apresenta um projecto de Norma Portuguesa com o título

O presente trabalho apresenta um projecto de Norma Portuguesa com o título

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A