Papers
Info
Evolução do Dano em Modelos Físicos de Quebra Mares de Talude a Partir do Volume Erodido. Aplicações
A avaliação do dano causado pela agitação incidente em modelos físicos de quebra mares de taludes pode ser realizada comparando volumes e profundidades erodidas entre levantamentos consecutivos de cada talude.Atualmente, estes levantamentos podem ser realizados de forma não intrusiva, recorrendo a técnicas fotogramétricas, a laser scan ou a sensores de posição baseados na metolodologia Time of Flight (ToF). Dependendo das condições de levantamento e da metodologia de pós-processamento das nuvens de pontos obtidas, estas técnicas permitem obter modelos tridimensionais de superfície, com elevada precisão.Em detalhe, as diferenças de volume entre os levantamentos inicial e
Year: 2023
Author(s): Lemos, R.; Mendonça, A.C.; Fortes, C. J. E. M.; MARTINS, R.; Ferrão, R.
Editor: LisWater
Keywords: Porosidade do manto; Kinect; Modelos tridimensionais de superfície; Modelo físico; Quebra-mar
Info
Implementation and Validation of SAFEPORT System at Sines Harbour
SAFEPORT safety system aims to daily reports to the Sines harbor administration, potential emergency situations regarding ships
Year: 2023
Number Pages:
215
Author(s): Pinheiro, L.; Gomes, A.; Fortes, C. J. E. M.; Santos, J. A.
: Defect and Diffusion Forum
Editor: Trans Tech Publications, Ltd.
Volume:
Vol. 427.
Keywords: Risk analysis; Moored ships; Wave propagation; SWAMS; SAFEPORT
Info
Implementation of the SWASH model into HIDRALERTA system
Early warning systems are an important tool for local authorities to detect emergency situations in advance and initiate the necessary safety measure. These systems often depend on numerical models to estimate wave overtopping in the affected areas. The SWASH model has shown to deliver good results in recent overtopping studies. The To-SEAlert project has the aim of increasing the efficiency, robustness and reliability of the HIDRALERTA early warning system. This study shows a first intent to implement the SWASH model to simulate wave overtopping for the Ericeira prototype. SWASH was implemented for one breakwater profile used to simulate the overtopping discharge and evaluate the associated risk levels. It was compared to the current approach used in HIDRALERTA, which resorts to a neural network trained with a physical modeling database, NN_OVERTOPPING2. Finally, both approaches were compared with previously analyzed video images of the breakwater. The results showed that SWASH generally overestimates overtopping and is not in good agreement with the video images. NN_OVERTOPPING2 has a better agreement with the video images. A possible reason for the overestimation might be the wave direction, which cannot be included in one-dimensional simulations in SWASH.
Year: 2023
Number Pages:
20-31pp..
Author(s): Manz, A.; Zózimo, A. C.; Fortes, C. J. E. M.; Pinheiro, L.; Garzon, J.L.
: Latin-American Journal of Computing
Editor: Zenodo
Volume:
Vol 10, nº 2.
Keywords: SWASH model; Risk reduction; Wave overtopping; Early warning system
Info
New HIDRALERTA prototypes: Peniche and Quarteira
Early Warning Systems are crucial disaster-risk-reduction strategies as they allow local authorities to prepare and implement in advance the necessary measures to avoid major destruction and risk for individuals and properties caused by storm events. HIDRALERTA is a forecast, early warning and risk assessment system for port and coastal areas that uses forecasts of sea waves and water levels to evaluate overtopping/flooding events and risks associated with the mooring of ships. The distinguishing feature of this system is that the risk assessment is based on specific parameters related to the actual risk being predicted, such as overtopping discharges, or the ship
Year: 2023
Number Pages:
17p..
Author(s): Zózimo, A. C.; Pinheiro, L.; Manz, A.; Garzon, J.L.; Fortes, C. J. E. M.; Ferreira, Ó.
: Revista Mundi Engenharia, Tecnologia e Gestão
Editor: Mundi
Volume:
Vol 8, nº 1.
Keywords: Overwash; Overtopping; HIDRALERTA; Early warning systems
Info
Numerical analysis of performance of an oscillating water column wave energy converter inserted into a composite breakwater with rubble mound foundation
In this study, performance of an oscillating water column wave energy converter inserted into a hypothetical composite breakwater with rubble mound foundation located at the southern Brazilian coast is analyzed. The FLUENT® numerical model, which is based on the Reynolds-Averaged Navier-Stokes equations, is used in 2D numerical simulations by adopting the Volume of Fluid method to consider the two-phase flow (water and air). The influence of the rubble mound foundation on the pneumatic power, the run-up/down, the free surface elevation inside the chamber, and the energy balance for different incident waves are investigated. The rubble mound foundation of the composite breakwater slightly affected hydrodynamics; however, it reduced significantly the pneumatic power of the device from 7 to 15% comparing with that obtained to a vertical breakwater founded on an impermeable foundation.
Year: 2023
Author(s): Teixeira, P.; Didier, E.
: Ocean Engineering
Editor: ELSEVIER
Volume:
278 (2023) 114421.
Keywords: RANS-VoF; Rubble mound foundation; Composite breakwaters; Oscillating water column; Wave energy
Info
Performance of an oscillating water column wave energy converter integrated with three types of harbor protection structures
Oscillating water column (OWC) wave energy converters can be integrated in harbor protection structures, such as vertical, rubble mound and piled breakwaters. The interaction between the incident wave and the structure, in which the OWC device is integrated, is significantly different, since the structure of the vertical breakwater is impermeable, while that of the rubble mound breakwater is porous. The performance of the OWC device for the three configurations is analyzed for a range of wave periods from 6 to 12 s and a wave height of 1 m. The OWC device integrated into the vertical breakwater shows the best performance (maximum mean pneumatic power of 70 kW), and the mean pneumatic power is globally 3 % higher than that of the OWC device integrated into the rubble mound breakwater (maximum mean pneumatic power of 67.4 kW). The performance of the OWC device integrated into the piled breakwater shows a similar trend to the OWC device integrated into the vertical breakwater for wave periods lower than 9 s, but it has a significant loss of performance for higher wave periods.
Year: 2023
Number Pages:
63-73pp.
Author(s): Didier, E.; Teixeira, P.
: Defect and Diffusion Forum
Editor: Trans Tech Publications Ltd, Switzerland
Volume:
Vol 427.
Keywords: Vertical Breakwater; Rubble Mound Breakwater; RANS; Oscillating Water Column; Numerical Simulation
Info
A novel geometry of an onshore Oscillating Water Column wave energy converter
This study aims proposing a novel geometry of the onshore Oscillating Water Column (OWC) device to increase its efficiency. A comparison between standard OWC
Year: 2022
Author(s): Güths, A.; Teixeira, P.; Didier, E.
: Renewable Energy
Editor: Elsevier
Keywords: Numerical simulation; Renewable energy; Wave energy; Oscillating water column
Info
Amarração de navios nos terminais do porto de Sines em situações de tempestade
Este trabalho descreve a aplicação do sistema SAFEPORT no Porto de Sines, e em particular, o teste de uma das funcionalidades do sistema relacionada com otimização de operações marítimas em ambiente portuário. O SAFEPORT é um sistema de previsão e alerta de perigosassociados a navegação.A aplicação do sistema SAFEPORT permitiu a otimização dos esquemas de amarração de três navios distintos acostados em três terminais do Porto de Sines, sob as condições de agitação marítima provocadas pela tempestade Dora (4 de dezembro de 2020). Foram construídos os modelos dos três navios e analisados vários esquemas de amarração a fim de obter uma solução ótima para cada navio. Este exercício mostrou que o sistema SAFEPORT é uma ferramenta útil para apoio à decisão nos sistemas de amarração dos navios. A configuração dos cabos de amarração tem grande influência no comportamento, e consequentemente na segurança, dos navios amarrados sujeitos a situações de tempestade.
Year: 2022
Author(s): Gomes, A.; Pinheiro, L.; Santos, J. A.; Fortes, C. J. E. M.
Editor: PIANC
Info
An estimation of the damage of scale models of breakwaters using the time of flight method
The assessment of damage evolution in scale model tests of rubble-mound breakwaters can be achieved by comparing eroded depths and volumes between consecutive surveys. Aiming to evaluate damage evolution on rubble-mound breakwater, scale model tests were recently conducted on the maritime hydraulic facilities of the National Laboratory for Civil Engineering. This paper focuses on the use of novel, non-intrusive survey methodologies such as the Time of Flight (ToF) principle technique. In this study, damage evaluation is based on the comparison of point clouds obtained before and after each test series, enabling the calculation of eroded depths and eroded volumes and the estimation of displaced units by using a non-dimensional damage parameter based on the eroded volume.
Year: 2022
Number Pages:
49-58pp..
Author(s): Lemos, R.; Fortes, C. J. E. M.; Silva, L. G.; Pinheiro, L.
: Revista Mecânica Experimental
Editor: APAET
Volume:
Nº 35, APAET (2022).
Keywords: Measuring Techniques; 3D Surveying; Breakwater; Stability
Info
Aplicação do modelo SWASH para a estimativa de galgamentos em eventos de tempestade no porto da Ericeira
Este trabalho analisa a potencialidade do modelo numérico SWASH ser implementado no protótipo do sistema HIDRALERTA para o porto da Ericeira para a estimativa do galgamento.O modelo SWASH foi aplicado a dois perfis transversais do porto da Ericeira com características geométricas distintas, diferentes orientações face à agitação incidente e com diferentes blocos de betão no manto principal. Esta comunicação foca-se nos resultados para um perfil cujo manto principal é constituído por tetrápodes. O coeficiente de Manning foi utilizado como parâmetro de calibração dos resultados do modelo SWASH, na simulação de duas tempestades, tendo como referência os resultados da ferramenta neuronal NN_OVERTOPPING2. Foram deduzidas trêsexpressões empíricas para a determinação do coeficiente de Manning com base em variáveis conhecidas, pois a possibilidade de calcular os valores dos coeficientes de Manning de forma automática é essencial para que se possa implementar o modelo SWASH no sistema HIDRALERTA.
Year: 2022
Author(s): Manz, A.; Zózimo, A. C.; Garzon, J.L.
Editor: PIANC
|
Comunicação
Info
Ferramenta de apoio à gestão costeira e portuária: o sistema HIDRALERTA
Nesta comunicação, descreve-se o sistema HIDRALERTA (sistema de previsão e alerta de inundações em zonas costeiras e portuárias), sistema em ambiente SIG que tem como ideia-base a utilização de previsões da agitação marítima (a 180 horas) para calcular os seus efeitos na costa, nomeadamente em termos de galgamentos e inundações. Dos desenvolvimentos mais recentes ou em curso destacam-se: a construção de mapas de risco costeiro, a partir da análise de uma série de 30 anos de dados de agitação marítima; o desenvolvimento e aplicação do sistema de alerta e da plataforma WEB para a zona da praia de São João da Caparica e para o porto e baía da Praia da Vitória (Terceira, Açores); a aplicação, com recurso a ferramentas SIG, de metodologias quantitativas de análise das consequências do galgamento/inundação (por exemplo, o Processo de Análise Hierárquica
Year: 2015
Number Pages:
18p.
Author(s): Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.; Santos, J. A.; Garcia, T.; Capitão, R.; Pinheiro, L.; Reis, R.; Craveiro, J.; Lourenço, I.; Lopes, P.; Rodrigues, A.; Sabino, A.; Araújo, J; Ferreira, J.
Editor: Carlos Coelho et al. Associação Portuguesa de Recursos Hídricos, 2015
Keywords: Sistema HIDRALERTA; SIG; Gestão costeira e portuária; Galgamento/inundação; Avaliação de risco; Agitação marítima
Info
Influence of coastal structures in velocity fields and wave height
The behaviour of a coastal structure depends on the nearshore hydrodynamics which isdependent from waves and their interaction with the structure. The knowledge of the wave transformationand breaking characteristics close to coastal structures becomes crucial for understanding the physicalprocesses that are involved and to the design of those coastal structures. Physical models and laboratoryexperiments are important tools for a better knowledge and characterization of these phenomena. In thiswork, wave flume tests were performed to analyse the wave hydrodynamics in the vicinity of a structure,constructed with a typical slope of a rubble-mound breakwater. We measured the free surface elevationand velocities by means of resistive probes and Acoustic Doppler Velocimetry. The results enable theidentification of complex phenomena in velocity field and several changes in the velocity field and waveheight caused by set-up, reflexion and wave breaking due to the presence of the structure. The increase ofthree-dimensional effects in the vicinity of the structure was also verified. The reliable experimental datacould be used to numerical models data validation.
Year: 2015
Number Pages:
196-206pp.
Author(s): Carvalho, R.; Fortes, C. J. E. M.; Castro, M.
Keywords: Breaking waves; Surf zone; Velocity fields; Wave height; Coastal structure physical models
Info
Monitoring of the water particle velocity field near the seabed under different wave and tidal scenarios: a real case
Monitoring of water particle velocity on the sea bed is crucial to study morphological shore changes in a coast at intermediate and shallow water depth under progressive surface waves and tidal flow current. Therefore, 3-D particle velocity was monitored continuously at the bottom of Santa Maria del Mar (SMM) beach (SW Spain) by means of a single point current meter during 3 weeks in 2007 since August 28. The current meter was placed at 0.45m above the seabed in order to acquire instantaneous velocity. Wave properties (height and period) were taken from the nearby wave buoy and tidal data were taken from a tidal gauge station. Wave-induced bottom particle velocities were obtained during spring and neap tides at a d/L (depth over wave length) parameter ranging from 0.06 to 0.3. Bottom water particle velocity near the seabed ranges from 0 to ± 0.5 m/sec of which about 82% does not exceed 0.2 m/sec during monitoring. Therefore, only 18% of the surveyed water particle velocities exceed the critical Shield parameter of the beach sand (d50 = 0.23mm) which is about 0.05-0.2 depending on Reynolds number. Results show that maximum horizontal speed is obviously lower during the slack tide (high or low tide) in comparison with flood tide and ebb tide. Moreover, speed is higher during ebb tide in comparison to adjacent flood tide, with steady wave climate. Finally and among other conclusions, the maximum real values of the bottom current surveyed in SMM, as well as the Shield parameter, substantially coincide with the theoretical estimates calculated for a given wave and tidal climate.
Year: 2015
Number Pages:
275-286pp.
Author(s): Khan-Mozahedy, A.B.M.; Muñoz-Perez, J.; Neves, M. G.
Keywords: Shield parameter; Intermediate water depth; Tidal current; Tide; Bottom orbital velocity
Info
Normas e recomendações em obras portuárias
No domínio específico do projeto e construção de obras marítimas e portuárias, ao contrário de outro tipo de obras de engenharia, não existe normativa de carácter obrigatório. No entanto, embora não haja legislação específica, existem, em diversos países, recomendações nacionais que reúnem os conceitos e critérios necessários ao Projeto, de forma a melhorar a segurança e otimizar obras de grande importância económica. Normalmente as recomendações focam não só o dimensionamento e construção de obras marítimo-portuárias e costeiras, novas ou extensão das existentes, mas também a sua monitorização e manutenção. Esta comunicação resume as recomendações internacionais existentes, já que em Portugal não há normativas nem recomendações nacionais para apoio ao dimensionamento hidráulico/estrutural de obras marítimas, incluindo as específicas para o dimensionamento geotécnico de obras marítimas e uma breve comparação entre elas.
Year: 2015
Number Pages:
4p.
Author(s): Neves, M. G.
Editor: SPG
Keywords: Obras portuárias; Recomendações
Info
Photogrametric techniques to health monitoring control of breakwater's structure using Scilab
The need for shelter zones in coastal areas leads to the construction ofstructures for shore protection such as breakwaters. Its design is mainly made based insemi-empirical formulas [1] [2] [3] and in the experience of the project designer, being thee ectiveness of the breakwater carried out through physical modelling.The Harbours and Maritime Structures Division of National Laboratory (NPE, portugueseacronym) for Civil Engineering (LNEC, portuguese acronym) have developed several ex-periments in bidimensional and tridimensional models. Through this experiments, thestability of the breakwater is tested and the evaluation of damage is made by counting thearmor units dislocated (movements or displacements).This damage evaluation is currentlydone by visual inspection thus being a subjective method where some relevant movementsmay go unnoticed.
Year: 2015
Number Pages:
9p.
Author(s): Lemos, R.; Loja, M.A.R.; Rodrigues, J.C.L.; Rodrigues, J.A.S.
Editor: ECCOMAS
Keywords: Scilab; Image processing; Breakwater; Health monitoring; Photogrametry
Info
Rubble-mound breakwater armour units displacement analysis by means of digital images processing methods in scale models
Rubble-mound structures are commonly used for coastal and port protection and needs aproperly design as well as inspection and maintenance during its lifetime. The design of such breakwatersusually requires a physical scale model to be tested under different irregular incident wave and tideconditions in order to evaluate its hydraulic and structural behaviour, namely the stability of the proposeddesign. Armour units displacement and fall analysis in physical models are then a key point in the designverification and usually requires a trained technician. In this work, an algorithm made in Matlab® ispresented, consisting in digital images processing and analysis which allows automatic and precisedisplacement detection as well as its location in time and space. For a selected displacement, it is alsopossible to characterize it.
Year: 2015
Number Pages:
171-184pp.
Author(s): Courela, J.M.; Carvalho, R.; Lemos, R.; Fortes, C. J. E. M.; Leandro, J.
Keywords: Armour units displacement; Image-processing; Matlab®; Rubble-mound breakwaters
Info
A comparison of wave characteristics at Caparica beach, Portugal, using in-situ and transferred wave data
The HIDRALERTA system is current1y being implemented as a novel ear1y warning system to assess the risk of flooding in coastal and port region areas. With forecasted sea wave conditions at coastal and port areas, the system is able to determine the effects of waves in terms of wave overtopping and flooding, to compare those results with pre-specified thresholds, to build alert maps, and, if necessary, to issue alert messages. The system will be applied to two case studies: Praia da Vitória harbor, in Terceira Island, Azores, and Caparica beach, near Lisbon. One of the major inputs of this integrated system is the characterization of sea wave conditions at the site of interest, so that both measured wave data and selected numerical models are used. Numerical models, however, should be calibrated for each area of application. This paper is a contribution to get a better insight of the wave characteristics at one of those case studies, the Caparica beach, to provide adequate calibration of the mentioned numerical models. Therefore, two measurement campaigns were organized at that location, using several instruments. Data was collected and analyzed, then compared with those transferred from the Port of Lisbon wave buoy, by using numerical wave propagation models, which then enabled one to evaluate SWAN's performance and to calibrate some of its parameters. Thus, the paper describes the sea wave characterization using both in-situ data and transferred data from the Port of Lisbon wave buoy, and discusses the SWAN' s strengths and weaknesses to simulate thewave conditions measured at the two above mentioned campaigns.
Year: 2014
Number Pages:
161-170pp.
Author(s): Capitão, R.; Fortes, C. J. E. M.; Poseiro, P.
Keywords: Swan model; Wave characterization; Waming and alert system
Info
Análise do desempenho do modelo SWAN na zona da Costa da Caparica
O sistema HIDRALERTA é um sistema de previsão e alerta de risco de galgamento e inundações emáreas costeiras e portuárias, atualmente em desenvolvimento. Para obtenção das condições de agitação marítimalocais são utilizados modelos numéricos de propagação de ondas, nomeadamente o modelo SWAN. Este trabalhovisa contribuir para uma melhor compreensão das características da agitação marítima local num dos casos deestudo considerados no projeto: a praia de S. João de Caparica. Assim, utilizaram-se os dados recolhidos em duascampanhas de medição naquela zona, os quais foram depois analisados e comparados com os resultados obtidospelo modelo SWAN para o mesmo local. Foi ainda feita a comparação entre os dados fornecidos pela boia daAPL e o modelo SWAN, no local da boia. Estes procedimentos permitiram avaliar o desempenho do modeloSWAN para este local.
Year: 2014
Number Pages:
183-186pp.
Author(s): Capitão, R.; Fortes, C. J. E. M.; Poseiro, P.; Raposeiro, P.
Keywords: Swan; Agitação marítima; Sistema de previsão e alerta
Info
Aplicação do modelo numérico SWAN em locais com vegetação na Hidrovia Tiete-Paraná
Este artigo descreve a aplicação do modelo SWAN-VEG para o lago da barragem de Ilha Solteira - São Paulo, Brasil, que faz parte da Hidrovia Tietê-Paraná, a fim de analisar a influência da vegetação sobre a redução da energia das ondas perto das margens do lago. Primeiramente, o modelo é aplicado, considerando uma profundidade constante em todo o reservatório da barragem e uma pequena área de vegetação localizada junto ao paredão da barragem. São testados vários valores de velocidade e direção do vento, bem como diferentes tipos de vegetação. Em seguida, a batimetria real do lago é considerada, bem como vegetação em determinadas zonas nas margens do lago. Várias condições de vento são testadas e comparadas para as situações com e sem vegetação.
Year: 2014
Number Pages:
189-198pp.
Author(s): Vieira, A. S.; Gregório, I.C.; Fortes, C. J. E. M.; Suzuki , T.; Maciel, G.
Keywords: Vegetação; Ilha Solteira; SWAN-VEG
Info
Aplicação do processo de análise hierárquica (AHP) na avaliação das consequências de galgamento em zonas portuárias
No presente trabalho descreve-se a aplicação de uma metodologia de avaliação do risco de galgamento em zonas costeiras e portuárias ao porto de Ponta Delgada, Açores, dando especial ênfase à avaliação das consequências da ocorrência de galgamentos não admissíveis através de uma análise multicritério (Processo de Análise Hierárquica, AHP).A metodologia de avaliação do risco é efetuada em três fases: Caraterização da agitação incidente nasestruturas do porto; Cálculo do galgamento; Avaliação do risco de galgamento, que inclui a avaliação daprobabilidade de ocorrência de galgamentos (acima de um certo limiar predefinido), assim como a avaliação das consequências dessas ocorrências. Por sua vez, esta avaliação das consequências é efetuada utilizando quer um procedimento simplista de classificação das consequências em termos de graus, quer uma metodologia baseada no AHP.Os resultados da aplicação desta metodologia da avaliação do risco são apresentados sob a forma de mapas de consequências e de risco, ferramentas importantes para o planeamento de operações e de futuras intervenções no porto de Ponta Delgada.
Year: 2014
Number Pages:
421-426pp.
Author(s): Rodrigues, J.; Poseiro, P.; Reis, M. T.; Fortes, C. J. E. M.; Taveira-Pinto, F.
Keywords: Estruturas marítimas; Portos; Inundação; Galgamento; Risco
|
|
Capítulo de Livro
Info
Multi-functional artificial reefs for coastal protection
N/A
Year: 2009
Number Pages:
153-210 pp.
Author(s): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Tese de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Year: 1999
Number Pages:
159 p.
Author(s): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Year: 1998
Number Pages:
594 p.
Author(s): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Year: 1998
Number Pages:
346 p.
Author(s): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Year: 1973
Author(s): Carvalho, M. M.
Editor: ******
|
|
Relatório Científico
Info
An integrated harbour navigation control system. NATO Po-Navigation. Adenda ao "Project Plan" proposto ao "Programa Ciência para a Estabilidade. Fase III" da OTAN
N/A
Year: 1994
Author(s): Covas, J. A.
Info
Cais da Calheta, Ilha de S. Jorge - Açores. Memorando
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios em modelo reduzido de uma protecção marítima aderente.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios tridimensionais de estabilidade e galgamentos do molhe de protecção do porto de recreio náutico do porto de Sines.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Análise das condições do porto de Sines. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Selecção de locais viáveis. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Ligação da lagoa de Óbidos ao mar - Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Carvalho, M. M.; Capitão, R.; Fortes, C. J. E. M.; Covas, J. A.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Coimbra.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.; Capitão, R.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Palma de Maiorca.
N/A
Year: 1994
Author(s): Covas, J. A.
|
|
|
Outro
Info
Relato da missão a Bruxelas (28 a 30 de Outubro de 1998) para participação na 10ª Reunião da Acção Concertada Added Value Services in VTMIS do Programa Comunitário de I&D TRANSPORTS . Relatório efe
N/A
Year: 1998
Number Pages:
3 p.
Author(s): Covas, J. A.
Editor: ******
Info
Short-term stochastic numerical and physical simulation of sea waves - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI, na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
53 p.
Author(s): Capitão, R.; Pires Silva, A.; Medina, J. R.; Carvalho, M. M.
Editor: ******
Info
Transformações Não-Lineares de Ondas Marítimas em Zonas Costeiras - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI , na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
50 p.
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Editor: ******
Info
V Programa Quadro da União Europeia. Preparação da discussão dos Programas Específicos. Documento de trabalho da Comissão (COM (97) 553 Final). Grupo de Trabalho 6 Sustainable Mobility and Intermod
N/A
Year: 1998
Number Pages:
2 p.
Author(s): Covas, J. A.
Editor: ******
Info
Valores extremos da agitação marítima no Algarve - Proposta de Projecto de Investigação apresentado ao Programa de Intervenção nos Laboratórios do Estado (MCT-FCT), sub-projecto Valorização e Protec
N/A
Year: 1998
Number Pages:
11 p.
Author(s): Carvalho, M. M.; Capitão, R.
Editor: ******
|