Papers
Info
Study of the turbine power output of an oscillating water column device by using a hydrodynamic - aerodynamic coupled model
The availability of clean energy of wind waves is enough to meet current demand of the world, attracting researches to find devices with good performance to extract this type of energy. The oscillating water column converter is a type of device that has been extensively studied for this purpose. This paper describes a numerical analysis of an onshore oscillating water column device taking into account hydrodynamic and aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The numerical analyses are carried out by the Fluinco model, based on slightly compressible flow method to solve the Navier-Stokes equations, and employing the two-step semi-implicit Taylor-Galerkin method. The aerodynamic model is based on the first law of thermodynamics applied to the air column inside the chamber and on turbines similar to Pico
Year: 2016
Number Pages:
147
Author(s): Torres, F.; Teixeira, P.; Didier, E.
Editor: Elsevier
Volume:
125.
Keywords: Air pressure control; Turbine model; Oscillating water column; Wave energy; Finite element method
Info
Força de impacto num quebra-mar vertical: comparação entre um modelo numérico SPH e formulações empiricas
O conhecimento dos esforços resultantes da interacção de uma onda com um quebra-mar verticaltorna-se essencial no dimensionamento deste tipo de estruturas. No presente trabalho, o modelo numérico SPHyCE, baseado numa metodologia de tipo SPH - Smoothed Particle Hydrodynamics, é utilizado para o cálculo das forças num quebra-mar vertical. Para analisar a evolução das forças de impacto foram consideradas várias condições de profundidade no pé da estrutura e de altura de onda incidente abrangendo diferentes regimes de forças. A comparação dos resultados do modelo numérico com os das formulações empíricas permitiu verificar que as forças previstas são semelhantes para os casos de regime de onda parcialmente estacionária. No entanto, para o regime de forças de impacto, existem diferenças que se devem a diversos factores: i) a rebentação da onda no modelo SPHyCE pode não corresponder necessariamente à forma de rebentação prevista nas formulações empíricas; ii) no caso da rebentação com aprisionamento de ar, cuja influência no valor das forças é relevante, o modelo numérico atinge o seu limite de aplicação, pois não integra o ar e não existem formulações aplicáveis; iii) as formulações empíricas aplicáveis com rebentação dão valores claramente por excesso.
Year: 2015
Number Pages:
3-26pp.
Author(s): Didier, E.; Rodrigues, A.; Neves, M. G.; Neves, D. R.; Dias, J.
: Revista Iberoamericana de Ingeniería Mecánica
Editor: UNED
Volume:
Vol. 19, N.º 2.
Keywords: Formulações empíricas; Interacção onda-estrutura; Modelação numérica; Quebra-mar vertical; Smoothed Particle Hydrodynamics; Forças de impacto
Info
Physical modelling as a fundamental tool for the design of harbours and maritime structures
In this paper, a brief description of the role of physical modelling to support the design of harbours and maritime structures is presented, followed by an example of the tests carried out for the studies of the expansion of Rabo de Peixe fi shing harbour, at São Miguel
Year: 2015
Number Pages:
135-145pp.
Author(s): Reis, M. T.; Silva, L. G.; Neves, M. G.; Lemos, R.; Capitão, R.; Fortes, C. J. E. M.
: PIANC Yearbook 2014
Keywords: Rabo de peixe harbour; Maritime structures; Harbours; Physical modelling
Info
Propuesta de estudio de la morfología determinada por el oleaje en playas fluviales. "La Concordia" en el río Uruguay, un caso práctico
Tanto el perfil como la forma en planta de las playas fluviales vienen establecidos por numerosos factoresentre los que cabría destacar las características del sedimento y la dirección y módulo de la velocidad de la corriente en el río. Sin embargo, en ciertos casos, lejos incluso de su estuario o desembocadura, esta morfología puede estar determinada principalmente por la incidencia del oleaje pese a no tratarse de un entorno marítimo.Se presenta aquí una metodología cualitativa que nos permitirá reconocer los aspectos que influyen en la existencia de este tipo de morfologías. Para ello, se estudiará un caso particular, el de la playa de La Concordia ubicada en la margen izquierda del río Uruguay a 70 km de su desembocadura en el estuario del Rio de la Plata. Asimismo se analizará la forma en planta y se verificará que la misma está determinada por la acción del oleaje.
Year: 2015
Number Pages:
49
Author(s): Muñoz-Perez, J.; Solari, S.; Teixeira, L; Alonso, R.; Neves, M. G.
: Geo-temas
Volume:
15.
Keywords: Oleaje; Difracción; Refracción; Playas fluviales
Info
Sinking of concrete modules into a sandy seabed: a case study
Three submerged coastal structures on the sandy seabed at SantaMaria delMar (SMM) Beach in Southwest Spain were monitored during the sixmonths after installation, starting inNovember of 2005. The monitoring evaluated the self-burial phenomenon of the 40 precast modular concrete elements of the three structures. Assessment included scouring around the structures, their vertical movement, the sinking velocity of the modules and the resulting beach profiles. Pressure sensors and precision topographies permitted continuous monitoring of the self-burial process for the first time in a full-scale case. Comparison of two bathymetries (one performed immediately prior to installation and another performed six months after installation) indicated slight accretion of the seabed,whereas intermediate topographic surveys indicated extensive scouring around the structures. The three structures began sinking into the sandy bottomplatform immediately after placement and continued until they reached the rocky bottom. This study implemented a new methodology using pressure sensors attached to the concrete modules to monitor the structural sinking. Unexpectedly, the average sinking speed was extremely rapid at approximately 3
Year: 2015
Number Pages:
26
Author(s): Muñoz-Perez, J.; Khan-Mozahedy, A.B.M.; Neves, M. G.; Tejedor, B.; Gomez-Pina, G.; Campo, J.; Negro, V.
: Coastal Engineering
Volume:
99.
Keywords: Self-buried; Low crested breakwaters; Liquefaction; Scouring; Sandy seabed
Info
Stability formula and failure probability analysis of wave-dissipating blocks considering wave breaking
The effects ofwave steepness andwave breaking on the stability of wave-dissipating blocks placed on caisson breakwaters are examined by hydraulic experiments under conditions with and without wave breaking. It is confirmed that there is a clear dependence of the block stability on the wave steepness through the wave-breaking type, such as plunging and spilling breakers. The stability parameter in thespilling breaker case is larger than that in the plunging breaker case. For non-breaking wave conditions, there is no effect of the wave steepness. An empirical stability formula is proposed taking into account the effects of the wave steepness and the wave-breaking type. Finally, by using the stability formula, failure probabilities of the wave-dissipating blocks having a nominal diameter are evaluated by the first-orderreliability method of the Level II reliability analysis.
Year: 2015
Number Pages:
45-54pp.
Author(s): Mase, H.; Yasuda, T.; Reis, M. T.; Karunarathna , H.; Yang , J.
: Journal of Ocean Engineering and Marine Energy
Editor: Springer
Volume:
Vol. 1(1).
Keywords: Failure probability; Reliability analysis; Wave-breaking effect; Stability formula; Wave-dissipating block stability
Info
Tools for forecasting and evaluation of structural risk on maritime works
This paper describes recent advances on maritime structures
Year: 2015
Number Pages:
146-158pp.
Author(s): Fortes, C. J. E. M.; Lemos, R.; Reis, M. T.; Capitão, R.; Neves, M. G.; Silva, L. G.; Poseiro, P.
: PIANC Yearbook 2014
Editor: PIANC
Keywords: ANOSOM; Maritime inspections; Warning system; Risk evaluation; Maritime structures
Info
Wave propagation on a flume: numerical simulation
This paper presents the numerical simulations done by using the waves2Foam, an OpenFOAM® library, to simulate the propagation of regular waves without breaking in a three-dimensional flume. The numerical code solves the unsteady Navier-Stokes equations and uses a Volume-of-Fluid (VoF) method to identify the free surface. A regular incident wave with a 1.5s period and 0.1m wave height, was considered. This is one of the conditions from the wide range of wave flume tests conducted at the National Laboratory for Civil Engineering (LNEC) whose objective was to analyze the hydrodynamics of wave transformation and wave breaking for different incident conditions over a variable bathymetry. Comparisons are made between the numerical and the experimental results. These comparisons include time-series of wave-gauges records at several locations along the flume and the corresponding amplitude spectra; significant wave height and average period evolution along the flume; time-series of the velocity components at one section of the flume, measured at the middle of the water column; and hodograph representation of the velocity components, in the middle of the water column, in the xy, xz, and yz planes along the flume. It was found that the numerical results obtained are close to the experimental data. The observed differences are attributable to numerical inaccuracies as well as the differences between the wave generation method in the numerical and experimental tests.
Year: 2015
Number Pages:
95-102pp.
Author(s): Conde, J. M.; Roberto, P.T.S; Fortes, C. J. E. M.
: Engenharia Térmica (Thermal Engineering)
Volume:
Vol 14 - nº 1.
Keywords: Wave propagation; Free-surface; OpenFOAM; Navier
Info
A modelação física no apoio ao projeto de obras marítimas
Neste artigo, apresenta-se uma breve descrição do papel da modelação física no apoio ao projeto de obras marítimas, seguida de um exemplo de ensaios realizados no âmbito da ampliação do porto de pesca de Rabo de Peixe, São Miguel
Year: 2014
Number Pages:
26-30pp.
Author(s): Fortes, C. J. E. M.; Reis, M. T.; Neves, M. G.; Silva, L. G.; Capitão, R.; Lemos, R.
: Construção Magazine
Volume:
Nº 62.
Info
Avaliação da probabilidade de ocorrência de galgamentos não admissíveis no posto 2 do Terminal de granéis líquidos do porto de Sines
Descrevem-se os procedimentos para avaliar o caudal médio galgado sobre um trecho de um quebra-mar de taludesa partir das caraterísticas da agitação marítima incidente no mesmo trecho. Apresenta-se uma metodologia paraestimação de valores extremos daquele caudal, partindo das séries temporais da mesma variável, e ilustram-se essesprocedimentos num trecho do molhe oeste do porto de Sines que protege o posto 2 do terminal de granéis líquidos daação da agitação marítima. Este regime de extremos do caudal médio galgado é fundamental para a avaliação do riscode ocorrência de galgamentos não admissíveis no posto 2.
Year: 2014
Number Pages:
95-113pp.
Author(s): Reis, M. T.; Santos, J. A.; Capitão, R.; Neves, D. R.; Fortes, C. J. E. M.
: Territorium
Volume:
21.
Keywords: Porto de sines; Caudais médios extremos; Redes neuronais; Galgamento
|
Comunicação
Info
Ferramenta de apoio à gestão costeira e portuária: o sistema HIDRALERTA
Nesta comunicação, descreve-se o sistema HIDRALERTA (sistema de previsão e alerta de inundações em zonas costeiras e portuárias), sistema em ambiente SIG que tem como ideia-base a utilização de previsões da agitação marítima (a 180 horas) para calcular os seus efeitos na costa, nomeadamente em termos de galgamentos e inundações. Dos desenvolvimentos mais recentes ou em curso destacam-se: a construção de mapas de risco costeiro, a partir da análise de uma série de 30 anos de dados de agitação marítima; o desenvolvimento e aplicação do sistema de alerta e da plataforma WEB para a zona da praia de São João da Caparica e para o porto e baía da Praia da Vitória (Terceira, Açores); a aplicação, com recurso a ferramentas SIG, de metodologias quantitativas de análise das consequências do galgamento/inundação (por exemplo, o Processo de Análise Hierárquica
Year: 2015
Number Pages:
18p.
Author(s): Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.; Santos, J. A.; Garcia, T.; Capitão, R.; Pinheiro, L.; Reis, R.; Craveiro, J.; Lourenço, I.; Lopes, P.; Rodrigues, A.; Sabino, A.; Araújo, J; Ferreira, J.
Editor: Carlos Coelho et al. Associação Portuguesa de Recursos Hídricos, 2015
Keywords: Sistema HIDRALERTA; SIG; Gestão costeira e portuária; Galgamento/inundação; Avaliação de risco; Agitação marítima
Info
Influence of coastal structures in velocity fields and wave height
The behaviour of a coastal structure depends on the nearshore hydrodynamics which isdependent from waves and their interaction with the structure. The knowledge of the wave transformationand breaking characteristics close to coastal structures becomes crucial for understanding the physicalprocesses that are involved and to the design of those coastal structures. Physical models and laboratoryexperiments are important tools for a better knowledge and characterization of these phenomena. In thiswork, wave flume tests were performed to analyse the wave hydrodynamics in the vicinity of a structure,constructed with a typical slope of a rubble-mound breakwater. We measured the free surface elevationand velocities by means of resistive probes and Acoustic Doppler Velocimetry. The results enable theidentification of complex phenomena in velocity field and several changes in the velocity field and waveheight caused by set-up, reflexion and wave breaking due to the presence of the structure. The increase ofthree-dimensional effects in the vicinity of the structure was also verified. The reliable experimental datacould be used to numerical models data validation.
Year: 2015
Number Pages:
196-206pp.
Author(s): Carvalho, R.; Fortes, C. J. E. M.; Castro, M.
Keywords: Breaking waves; Surf zone; Velocity fields; Wave height; Coastal structure physical models
Info
Monitoring of the water particle velocity field near the seabed under different wave and tidal scenarios: a real case
Monitoring of water particle velocity on the sea bed is crucial to study morphological shore changes in a coast at intermediate and shallow water depth under progressive surface waves and tidal flow current. Therefore, 3-D particle velocity was monitored continuously at the bottom of Santa Maria del Mar (SMM) beach (SW Spain) by means of a single point current meter during 3 weeks in 2007 since August 28. The current meter was placed at 0.45m above the seabed in order to acquire instantaneous velocity. Wave properties (height and period) were taken from the nearby wave buoy and tidal data were taken from a tidal gauge station. Wave-induced bottom particle velocities were obtained during spring and neap tides at a d/L (depth over wave length) parameter ranging from 0.06 to 0.3. Bottom water particle velocity near the seabed ranges from 0 to ± 0.5 m/sec of which about 82% does not exceed 0.2 m/sec during monitoring. Therefore, only 18% of the surveyed water particle velocities exceed the critical Shield parameter of the beach sand (d50 = 0.23mm) which is about 0.05-0.2 depending on Reynolds number. Results show that maximum horizontal speed is obviously lower during the slack tide (high or low tide) in comparison with flood tide and ebb tide. Moreover, speed is higher during ebb tide in comparison to adjacent flood tide, with steady wave climate. Finally and among other conclusions, the maximum real values of the bottom current surveyed in SMM, as well as the Shield parameter, substantially coincide with the theoretical estimates calculated for a given wave and tidal climate.
Year: 2015
Number Pages:
275-286pp.
Author(s): Khan-Mozahedy, A.B.M.; Muñoz-Perez, J.; Neves, M. G.
Keywords: Shield parameter; Intermediate water depth; Tidal current; Tide; Bottom orbital velocity
Info
Normas e recomendações em obras portuárias
No domínio específico do projeto e construção de obras marítimas e portuárias, ao contrário de outro tipo de obras de engenharia, não existe normativa de carácter obrigatório. No entanto, embora não haja legislação específica, existem, em diversos países, recomendações nacionais que reúnem os conceitos e critérios necessários ao Projeto, de forma a melhorar a segurança e otimizar obras de grande importância económica. Normalmente as recomendações focam não só o dimensionamento e construção de obras marítimo-portuárias e costeiras, novas ou extensão das existentes, mas também a sua monitorização e manutenção. Esta comunicação resume as recomendações internacionais existentes, já que em Portugal não há normativas nem recomendações nacionais para apoio ao dimensionamento hidráulico/estrutural de obras marítimas, incluindo as específicas para o dimensionamento geotécnico de obras marítimas e uma breve comparação entre elas.
Year: 2015
Number Pages:
4p.
Author(s): Neves, M. G.
Editor: SPG
Keywords: Obras portuárias; Recomendações
Info
Photogrametric techniques to health monitoring control of breakwater's structure using Scilab
The need for shelter zones in coastal areas leads to the construction ofstructures for shore protection such as breakwaters. Its design is mainly made based insemi-empirical formulas [1] [2] [3] and in the experience of the project designer, being thee ectiveness of the breakwater carried out through physical modelling.The Harbours and Maritime Structures Division of National Laboratory (NPE, portugueseacronym) for Civil Engineering (LNEC, portuguese acronym) have developed several ex-periments in bidimensional and tridimensional models. Through this experiments, thestability of the breakwater is tested and the evaluation of damage is made by counting thearmor units dislocated (movements or displacements).This damage evaluation is currentlydone by visual inspection thus being a subjective method where some relevant movementsmay go unnoticed.
Year: 2015
Number Pages:
9p.
Author(s): Lemos, R.; Loja, M.A.R.; Rodrigues, J.C.L.; Rodrigues, J.A.S.
Editor: ECCOMAS
Keywords: Scilab; Image processing; Breakwater; Health monitoring; Photogrametry
Info
Rubble-mound breakwater armour units displacement analysis by means of digital images processing methods in scale models
Rubble-mound structures are commonly used for coastal and port protection and needs aproperly design as well as inspection and maintenance during its lifetime. The design of such breakwatersusually requires a physical scale model to be tested under different irregular incident wave and tideconditions in order to evaluate its hydraulic and structural behaviour, namely the stability of the proposeddesign. Armour units displacement and fall analysis in physical models are then a key point in the designverification and usually requires a trained technician. In this work, an algorithm made in Matlab® ispresented, consisting in digital images processing and analysis which allows automatic and precisedisplacement detection as well as its location in time and space. For a selected displacement, it is alsopossible to characterize it.
Year: 2015
Number Pages:
171-184pp.
Author(s): Courela, J.M.; Carvalho, R.; Lemos, R.; Fortes, C. J. E. M.; Leandro, J.
Keywords: Armour units displacement; Image-processing; Matlab®; Rubble-mound breakwaters
Info
A comparison of wave characteristics at Caparica beach, Portugal, using in-situ and transferred wave data
The HIDRALERTA system is current1y being implemented as a novel ear1y warning system to assess the risk of flooding in coastal and port region areas. With forecasted sea wave conditions at coastal and port areas, the system is able to determine the effects of waves in terms of wave overtopping and flooding, to compare those results with pre-specified thresholds, to build alert maps, and, if necessary, to issue alert messages. The system will be applied to two case studies: Praia da Vitória harbor, in Terceira Island, Azores, and Caparica beach, near Lisbon. One of the major inputs of this integrated system is the characterization of sea wave conditions at the site of interest, so that both measured wave data and selected numerical models are used. Numerical models, however, should be calibrated for each area of application. This paper is a contribution to get a better insight of the wave characteristics at one of those case studies, the Caparica beach, to provide adequate calibration of the mentioned numerical models. Therefore, two measurement campaigns were organized at that location, using several instruments. Data was collected and analyzed, then compared with those transferred from the Port of Lisbon wave buoy, by using numerical wave propagation models, which then enabled one to evaluate SWAN's performance and to calibrate some of its parameters. Thus, the paper describes the sea wave characterization using both in-situ data and transferred data from the Port of Lisbon wave buoy, and discusses the SWAN' s strengths and weaknesses to simulate thewave conditions measured at the two above mentioned campaigns.
Year: 2014
Number Pages:
161-170pp.
Author(s): Capitão, R.; Fortes, C. J. E. M.; Poseiro, P.
Keywords: Swan model; Wave characterization; Waming and alert system
Info
Análise do desempenho do modelo SWAN na zona da Costa da Caparica
O sistema HIDRALERTA é um sistema de previsão e alerta de risco de galgamento e inundações emáreas costeiras e portuárias, atualmente em desenvolvimento. Para obtenção das condições de agitação marítimalocais são utilizados modelos numéricos de propagação de ondas, nomeadamente o modelo SWAN. Este trabalhovisa contribuir para uma melhor compreensão das características da agitação marítima local num dos casos deestudo considerados no projeto: a praia de S. João de Caparica. Assim, utilizaram-se os dados recolhidos em duascampanhas de medição naquela zona, os quais foram depois analisados e comparados com os resultados obtidospelo modelo SWAN para o mesmo local. Foi ainda feita a comparação entre os dados fornecidos pela boia daAPL e o modelo SWAN, no local da boia. Estes procedimentos permitiram avaliar o desempenho do modeloSWAN para este local.
Year: 2014
Number Pages:
183-186pp.
Author(s): Capitão, R.; Fortes, C. J. E. M.; Poseiro, P.; Raposeiro, P.
Keywords: Swan; Agitação marítima; Sistema de previsão e alerta
Info
Aplicação do modelo numérico SWAN em locais com vegetação na Hidrovia Tiete-Paraná
Este artigo descreve a aplicação do modelo SWAN-VEG para o lago da barragem de Ilha Solteira - São Paulo, Brasil, que faz parte da Hidrovia Tietê-Paraná, a fim de analisar a influência da vegetação sobre a redução da energia das ondas perto das margens do lago. Primeiramente, o modelo é aplicado, considerando uma profundidade constante em todo o reservatório da barragem e uma pequena área de vegetação localizada junto ao paredão da barragem. São testados vários valores de velocidade e direção do vento, bem como diferentes tipos de vegetação. Em seguida, a batimetria real do lago é considerada, bem como vegetação em determinadas zonas nas margens do lago. Várias condições de vento são testadas e comparadas para as situações com e sem vegetação.
Year: 2014
Number Pages:
189-198pp.
Author(s): Vieira, A. S.; Gregório, I.C.; Fortes, C. J. E. M.; Suzuki , T.; Maciel, G.
Keywords: Vegetação; Ilha Solteira; SWAN-VEG
Info
Aplicação do processo de análise hierárquica (AHP) na avaliação das consequências de galgamento em zonas portuárias
No presente trabalho descreve-se a aplicação de uma metodologia de avaliação do risco de galgamento em zonas costeiras e portuárias ao porto de Ponta Delgada, Açores, dando especial ênfase à avaliação das consequências da ocorrência de galgamentos não admissíveis através de uma análise multicritério (Processo de Análise Hierárquica, AHP).A metodologia de avaliação do risco é efetuada em três fases: Caraterização da agitação incidente nasestruturas do porto; Cálculo do galgamento; Avaliação do risco de galgamento, que inclui a avaliação daprobabilidade de ocorrência de galgamentos (acima de um certo limiar predefinido), assim como a avaliação das consequências dessas ocorrências. Por sua vez, esta avaliação das consequências é efetuada utilizando quer um procedimento simplista de classificação das consequências em termos de graus, quer uma metodologia baseada no AHP.Os resultados da aplicação desta metodologia da avaliação do risco são apresentados sob a forma de mapas de consequências e de risco, ferramentas importantes para o planeamento de operações e de futuras intervenções no porto de Ponta Delgada.
Year: 2014
Number Pages:
421-426pp.
Author(s): Rodrigues, J.; Poseiro, P.; Reis, M. T.; Fortes, C. J. E. M.; Taveira-Pinto, F.
Keywords: Estruturas marítimas; Portos; Inundação; Galgamento; Risco
|
|
Capítulo de Livro
Info
Multi-functional artificial reefs for coastal protection
N/A
Year: 2009
Number Pages:
153-210 pp.
Author(s): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Tese de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Year: 1999
Number Pages:
159 p.
Author(s): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Year: 1998
Number Pages:
594 p.
Author(s): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Year: 1998
Number Pages:
346 p.
Author(s): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Year: 1973
Author(s): Carvalho, M. M.
Editor: ******
|
|
Relatório Científico
Info
An integrated harbour navigation control system. NATO Po-Navigation. Adenda ao "Project Plan" proposto ao "Programa Ciência para a Estabilidade. Fase III" da OTAN
N/A
Year: 1994
Author(s): Covas, J. A.
Info
Cais da Calheta, Ilha de S. Jorge - Açores. Memorando
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios em modelo reduzido de uma protecção marítima aderente.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Ensaios tridimensionais de estabilidade e galgamentos do molhe de protecção do porto de recreio náutico do porto de Sines.
N/A
Year: 1994
Author(s): Silva, L. G.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Análise das condições do porto de Sines. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Estudo da localização de um terminal de importação de gás natural liquefeito. Selecção de locais viáveis. Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Capitão, R.
Info
Ligação da lagoa de Óbidos ao mar - Estudos de agitação marítima.
N/A
Year: 1994
Author(s): Carvalho, M. M.; Capitão, R.; Fortes, C. J. E. M.; Covas, J. A.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Coimbra.
N/A
Year: 1994
Author(s): Covas, J. A.; Fortes, C. J. E. M.; Capitão, R.
Info
Modelação por elementos finitos da propagação e deformação de ondas marítimas em zonas costeiras. Missão a Palma de Maiorca.
N/A
Year: 1994
Author(s): Covas, J. A.
|
|
|
Outro
Info
Relato da missão a Bruxelas (28 a 30 de Outubro de 1998) para participação na 10ª Reunião da Acção Concertada Added Value Services in VTMIS do Programa Comunitário de I&D TRANSPORTS . Relatório efe
N/A
Year: 1998
Number Pages:
3 p.
Author(s): Covas, J. A.
Editor: ******
Info
Short-term stochastic numerical and physical simulation of sea waves - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI, na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
53 p.
Author(s): Capitão, R.; Pires Silva, A.; Medina, J. R.; Carvalho, M. M.
Editor: ******
Info
Transformações Não-Lineares de Ondas Marítimas em Zonas Costeiras - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI , na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
50 p.
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Editor: ******
Info
V Programa Quadro da União Europeia. Preparação da discussão dos Programas Específicos. Documento de trabalho da Comissão (COM (97) 553 Final). Grupo de Trabalho 6 Sustainable Mobility and Intermod
N/A
Year: 1998
Number Pages:
2 p.
Author(s): Covas, J. A.
Editor: ******
Info
Valores extremos da agitação marítima no Algarve - Proposta de Projecto de Investigação apresentado ao Programa de Intervenção nos Laboratórios do Estado (MCT-FCT), sub-projecto Valorização e Protec
N/A
Year: 1998
Number Pages:
11 p.
Author(s): Carvalho, M. M.; Capitão, R.
Editor: ******
|