Publications

Knowledge of forces due to the action of waves on submarine outfalls composed by a pipe and stabilizing concrete weights, considering the wave propagation direction to the outfalls, is essential to their design. 3D numerical models based on RANS-VoF (Reynolds-Average-Navier-Stokes Volume-of-Fluid) are able to estimate forces on the pipe and weights. The present study aims to simulate a submarine outfall with stabilizing concrete weights at 1:15 scale which was previously tested in the 3D Shallow Water Basin at the Danish Hydraulics Institute (DHI) to analyse the influence of the direction of the incident wave and the distance from the pipe to the bottom on the outfall forces. In this study, numerical results are compared with experimental ones for waves with four different amplitudes and with wave incidence perpendicular to the outfall. The use of k-

The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.

Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.

This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira

This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.

This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.

Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula

This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the

Nesta comunicação, descreve-se o sistema HIDRALERTA (sistema de previsão e alerta de inundações em zonas costeiras e portuárias), sistema em ambiente SIG que tem como ideia-base a utilização de previsões da agitação marítima (a 180 horas) para calcular os seus efeitos na costa, nomeadamente em termos de galgamentos e inundações. Dos desenvolvimentos mais recentes ou em curso destacam-se: a construção de mapas de risco costeiro, a partir da análise de uma série de 30 anos de dados de agitação marítima; o desenvolvimento e aplicação do sistema de alerta e da plataforma WEB para a zona da praia de São João da Caparica e para o porto e baía da Praia da Vitória (Terceira, Açores); a aplicação, com recurso a ferramentas SIG, de metodologias quantitativas de análise das consequências do galgamento/inundação (por exemplo, o Processo de Análise Hierárquica

The behaviour of a coastal structure depends on the nearshore hydrodynamics which isdependent from waves and their interaction with the structure. The knowledge of the wave transformationand breaking characteristics close to coastal structures becomes crucial for understanding the physicalprocesses that are involved and to the design of those coastal structures. Physical models and laboratoryexperiments are important tools for a better knowledge and characterization of these phenomena. In thiswork, wave flume tests were performed to analyse the wave hydrodynamics in the vicinity of a structure,constructed with a typical slope of a rubble-mound breakwater. We measured the free surface elevationand velocities by means of resistive probes and Acoustic Doppler Velocimetry. The results enable theidentification of complex phenomena in velocity field and several changes in the velocity field and waveheight caused by set-up, reflexion and wave breaking due to the presence of the structure. The increase ofthree-dimensional effects in the vicinity of the structure was also verified. The reliable experimental datacould be used to numerical models data validation.

Monitoring of water particle velocity on the sea bed is crucial to study morphological shore changes in a coast at intermediate and shallow water depth under progressive surface waves and tidal flow current. Therefore, 3-D particle velocity was monitored continuously at the bottom of Santa Maria del Mar (SMM) beach (SW Spain) by means of a single point current meter during 3 weeks in 2007 since August 28. The current meter was placed at 0.45m above the seabed in order to acquire instantaneous velocity. Wave properties (height and period) were taken from the nearby wave buoy and tidal data were taken from a tidal gauge station. Wave-induced bottom particle velocities were obtained during spring and neap tides at a d/L (depth over wave length) parameter ranging from 0.06 to 0.3. Bottom water particle velocity near the seabed ranges from 0 to ± 0.5 m/sec of which about 82% does not exceed 0.2 m/sec during monitoring. Therefore, only 18% of the surveyed water particle velocities exceed the critical Shield parameter of the beach sand (d50 = 0.23mm) which is about 0.05-0.2 depending on Reynolds number. Results show that maximum horizontal speed is obviously lower during the slack tide (high or low tide) in comparison with flood tide and ebb tide. Moreover, speed is higher during ebb tide in comparison to adjacent flood tide, with steady wave climate. Finally and among other conclusions, the maximum real values of the bottom current surveyed in SMM, as well as the Shield parameter, substantially coincide with the theoretical estimates calculated for a given wave and tidal climate.

No domínio específico do projeto e construção de obras marítimas e portuárias, ao contrário de outro tipo de obras de engenharia, não existe normativa de carácter obrigatório. No entanto, embora não haja legislação específica, existem, em diversos países, recomendações nacionais que reúnem os conceitos e critérios necessários ao Projeto, de forma a melhorar a segurança e otimizar obras de grande importância económica. Normalmente as recomendações focam não só o dimensionamento e construção de obras marítimo-portuárias e costeiras, novas ou extensão das existentes, mas também a sua monitorização e manutenção. Esta comunicação resume as recomendações internacionais existentes, já que em Portugal não há normativas nem recomendações nacionais para apoio ao dimensionamento hidráulico/estrutural de obras marítimas, incluindo as específicas para o dimensionamento geotécnico de obras marítimas e uma breve comparação entre elas.

The need for shelter zones in coastal areas leads to the construction ofstructures for shore protection such as breakwaters. Its design is mainly made based insemi-empirical formulas [1] [2] [3] and in the experience of the project designer, being thee ectiveness of the breakwater carried out through physical modelling.The Harbours and Maritime Structures Division of National Laboratory (NPE, portugueseacronym) for Civil Engineering (LNEC, portuguese acronym) have developed several ex-periments in bidimensional and tridimensional models. Through this experiments, thestability of the breakwater is tested and the evaluation of damage is made by counting thearmor units dislocated (movements or displacements).This damage evaluation is currentlydone by visual inspection thus being a subjective method where some relevant movementsmay go unnoticed.

Rubble-mound structures are commonly used for coastal and port protection and needs aproperly design as well as inspection and maintenance during its lifetime. The design of such breakwatersusually requires a physical scale model to be tested under different irregular incident wave and tideconditions in order to evaluate its hydraulic and structural behaviour, namely the stability of the proposeddesign. Armour units displacement and fall analysis in physical models are then a key point in the designverification and usually requires a trained technician. In this work, an algorithm made in Matlab® ispresented, consisting in digital images processing and analysis which allows automatic and precisedisplacement detection as well as its location in time and space. For a selected displacement, it is alsopossible to characterize it.

The HIDRALERTA system is current1y being implemented as a novel ear1y warning system to assess the risk of flooding in coastal and port region areas. With forecasted sea wave conditions at coastal and port areas, the system is able to determine the effects of waves in terms of wave overtopping and flooding, to compare those results with pre-specified thresholds, to build alert maps, and, if necessary, to issue alert messages. The system will be applied to two case studies: Praia da Vitória harbor, in Terceira Island, Azores, and Caparica beach, near Lisbon. One of the major inputs of this integrated system is the characterization of sea wave conditions at the site of interest, so that both measured wave data and selected numerical models are used. Numerical models, however, should be calibrated for each area of application. This paper is a contribution to get a better insight of the wave characteristics at one of those case studies, the Caparica beach, to provide adequate calibration of the mentioned numerical models. Therefore, two measurement campaigns were organized at that location, using several instruments. Data was collected and analyzed, then compared with those transferred from the Port of Lisbon wave buoy, by using numerical wave propagation models, which then enabled one to evaluate SWAN's performance and to calibrate some of its parameters. Thus, the paper describes the sea wave characterization using both in-situ data and transferred data from the Port of Lisbon wave buoy, and discusses the SWAN' s strengths and weaknesses to simulate thewave conditions measured at the two above mentioned campaigns.

O sistema HIDRALERTA é um sistema de previsão e alerta de risco de galgamento e inundações emáreas costeiras e portuárias, atualmente em desenvolvimento. Para obtenção das condições de agitação marítimalocais são utilizados modelos numéricos de propagação de ondas, nomeadamente o modelo SWAN. Este trabalhovisa contribuir para uma melhor compreensão das características da agitação marítima local num dos casos deestudo considerados no projeto: a praia de S. João de Caparica. Assim, utilizaram-se os dados recolhidos em duascampanhas de medição naquela zona, os quais foram depois analisados e comparados com os resultados obtidospelo modelo SWAN para o mesmo local. Foi ainda feita a comparação entre os dados fornecidos pela boia daAPL e o modelo SWAN, no local da boia. Estes procedimentos permitiram avaliar o desempenho do modeloSWAN para este local.

Este artigo descreve a aplicação do modelo SWAN-VEG para o lago da barragem de Ilha Solteira - São Paulo, Brasil, que faz parte da Hidrovia Tietê-Paraná, a fim de analisar a influência da vegetação sobre a redução da energia das ondas perto das margens do lago. Primeiramente, o modelo é aplicado, considerando uma profundidade constante em todo o reservatório da barragem e uma pequena área de vegetação localizada junto ao paredão da barragem. São testados vários valores de velocidade e direção do vento, bem como diferentes tipos de vegetação. Em seguida, a batimetria real do lago é considerada, bem como vegetação em determinadas zonas nas margens do lago. Várias condições de vento são testadas e comparadas para as situações com e sem vegetação.

No presente trabalho descreve-se a aplicação de uma metodologia de avaliação do risco de galgamento em zonas costeiras e portuárias ao porto de Ponta Delgada, Açores, dando especial ênfase à avaliação das consequências da ocorrência de galgamentos não admissíveis através de uma análise multicritério (Processo de Análise Hierárquica, AHP).A metodologia de avaliação do risco é efetuada em três fases: Caraterização da agitação incidente nasestruturas do porto; Cálculo do galgamento; Avaliação do risco de galgamento, que inclui a avaliação daprobabilidade de ocorrência de galgamentos (acima de um certo limiar predefinido), assim como a avaliação das consequências dessas ocorrências. Por sua vez, esta avaliação das consequências é efetuada utilizando quer um procedimento simplista de classificação das consequências em termos de graus, quer uma metodologia baseada no AHP.Os resultados da aplicação desta metodologia da avaliação do risco são apresentados sob a forma de mapas de consequências e de risco, ferramentas importantes para o planeamento de operações e de futuras intervenções no porto de Ponta Delgada.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A