Papers
Info
Synthetic zeolite pellets incorporated to air limemetakaolin mortars: Mechanical properties
In this study synthetic fine and coarse zeolite pellets were chosen in the development of air limemetakaolin mortars for repairing ancient masonry to be used in conservation and restoration of cultural heritage. Synthetic zeolite was used due to their particular water adsorption properties and act as an artificial pozzolan promoting the development of hydraulic phases. Physical, chemical, mineralogical and microstructural tests were accomplished to characterize the materials used in mortars preparation. Flexural, compressive strength and dynamic modulus of elasticity tests were performed in mortars at 28, 90 and 180 days of curing. Incorporation of both fine and coarse zeolite pellets caused improvement of mechanical strength of mortars. The highest flexural strength value ( 0.5 MPa) was achieved in both mortars with fine zeolites pellets at 90 days and 20 and 30 wt.% metakaolin, and coarse zeolite pellets at 180 days and 30 wt.% metakaolin as lime replacement. 1.0 MPa was the highest compressive strength value obtained at 180 days for mortars with both fine zeolite pellets and coarse zeolite pellets, with 20 and 30 wt.% of metakaolin, respectively. Elasticity modulus ranged from 2.3 GPa to 3.9 GPa confirming the high deformation capability of these mortars. Zeolite pellets type A is a promise synthetic material that could be successfully used in air lime metakaolin render mortars for applications in the conservation and restoration of cultural heritage.
Year: 2014
Number Pages:
243-252pp.
Author(s): Ferraz, E.; Andrejkovicová, S.; Velosa, A.; Santos Silva, A.; Rocha, F.
: Construction and Building Materials
Editor: Elsevier
Volume:
69.
Keywords: Modified chapelle test; Archaeological and historical buildings; Conservation and restoration; Pozzolanic effect; Zeolite type a
Info
The history of Portuguese interior plaster coatings: A mineralogical survey using XRD
The evolution of the materials used in Portuguese interior wall coatings since the Roman occupation, namely the binders, is investigated using XRD in order to build a preliminary systematic database to contribute to the design and study of compatible products for conservation and repair. The results show that lime was the main binder until the end of the 18th century, with gypsum overcoming its use in the 19th century. A relationship is established between the results and several influencing aspects, namely other cultures, the neighbouring countries and their traditional construction techniques, the availability of raw materials, the purposes/techniques of application and the geographical location.
Year: 2014
Number Pages:
19p.
Author(s): Freire, T.; Santos Silva, A.; Veiga, M. R.; Brito, J.
: Archaeometry
Editor: Wiley
Keywords: Gypsum plaster; Xrd analysis; Mineralogical composition; Interior coatings; Lime plaster; Portuguese heritage
Info
The ReAVA project: assessment of the potential alkali-reactivity of volcanic aggregates from Azores Islands
Volcanic rocks have been found to be potentially alkali-reactive in a number of countries, including Japan, New Zealand, Iceland and Turkey. In order to characterize the potential reactivity of the volcanic rocks in Azores a project is being carried out, under the support of the Azores Government: the ReAVA ProjectCharacterization of Potential Reactivity of the Volcanic Aggregates from the Azores Archipelago: Implications on the Durability of Concrete Structures. This project comprises mainly: (1) petrographic assessment of the aggregates, (2) assessment of their performance in expansion tests and (3) site inspection of existing large concrete structures. This study has also the support of the IMPROVE ProjectImprovement of Performance of Aggregates in the Inhibition of Alkali-Aggregate Reactions in Concrete, aiming to minimize the occurrence of alkali aggregate reaction (AAR) in Portugal. The Azorean rocks used as aggregates are mainly basalts and some trachytes. The reactivity of this kind of rocks is usually associated with the presence of volcanic glass, altered minerals and SiO2 content of the rock. The petrographic examinations of the rocks confirmed that one of the basaltic samples contains volcanic glass. The occurrence of microcrystalline quartz as a secondary product filling the interstices of the trachyte sample was confirmed by scanning electron microscope. The results of the concrete expansion test RILEM AAR-3 showed an increasing expansion starting on 140 days and continued to grow after 2 years of laboratory testing, but below the limit of 0.05 % recommended for this method.
Year: 2014
Number Pages:
51-54pp.
Author(s): Medeiros, S.; Nunes, J. C.; Katayama, T.; Fernandes, I.; Santos Silva, A.; Miranda, V.; Soares, D.
: Urban Geology, Sustainable Planning and Landscape Exploitation
Editor: Springer
Volume:
5.
Keywords: Expansion tests; Petrography; Volcanic aggregates
Info
Alkali-Aggregate Reactions in Concrete: Methodologies Applied in the Evaluation of Alkali Reactivity of Aggregates for Concrete
The alkali-aggregate reaction (AAR) in concrete is a group of chemical reactions that involves the reaction of certain minerals present in the aggregates with alkali and hydroxyl ions in the interstitial solution of cement paste in concrete. These reactions form an alkaline hygroscopic gel that absorbs water and expands causing internal stresses with cracking. The AAR mitigation measures oblige the correct evaluation of the alkali reactivity of the aggregates. This is normally assessed by petrographic, chemical or expansion test methods. Several studies regarding alkali reactivity of aggregates for concrete structures in Portugal, including bridges and dams, indicated that their field performance does not correspond to the previously performed evaluation. Presently, Portuguese methodology is based on the LNEC Specification E461-2007, which shows some limitations regarding rock types such as granitoids. This situation motivated the development of a research project, involving medium and long term expansion tests in different conditions, under accelerated and natural exposure conditions, as well as petrographic evaluation of the main Portuguese aggregates used/to be used in concrete. This paper presents the preliminary results of this research.
Year: 2013
Number Pages:
409-414pp.
Author(s): Santos Silva, A.; Soares, D.; Matos, L.; Fernandes, I.; Salta, M. M.
: Materials Science Forum
Editor: Trans Tech Publications
Volume:
Vols. 730-732.
Keywords: Concrete; Alkali reactivity; Aggregates; Asr
Info
ASR of mortars containing glass
Glass is a material that raises environmental issues in terms of both recycling and dumping. Some studies have shown the potential of glass as pozzolan when used as fine powder. Its use as aggregate in cementitious materials may in certain circumstances lead to alkali silica reaction (ASR) related problems. ASR is one of the most studied deleterious degradation mechanisms of concrete, which is particularly harmful. Once detected in a concrete structure, ASR is very difficult to stop. It is nowadays possible to use mineral additions like natural pozzolans or sub-products with pozzolanic reactivity to inhibit ASR in new concrete. This work shows the results of using a Portuguese recycled glass material as aggregate or as pozzolan in cement based mortars, to ascertain their applicability in concrete. The incorporation of glass as cement replacement or even as aggregate can decrease the ASR effects and its efficiency is related with the replacement ratio.
Year: 2013
Number Pages:
489495pp.
Author(s): Serpa, D.; Santos Silva, A.; Brito, J.; Pontes, J.; Soares, D.
: Construction and Building Materials
Editor: Elsevier
Volume:
47.
Keywords: Recycling; Glass; Construction and demolition waste; Alkali-silica reaction
Info
Behaviour of Glass in Cement-based Materials: Its Role on ASR
One of the most worrying degradation mechanisms in hardened concrete is the occurrence of chemical expansive reactions, namely due to alkali-silica reactions (ASR). This pathology involves the formation of expansive products inside the material. This situation is very difficult to deal with, because presently there is no efficient method to repair concrete structures affected by ASR. Hence, there is an urgent need to find preventive methods that may inhibit these reactions in new concrete structures. Nowadays, the use of pozzolanic mineral additions is recommended to mitigate this type of degradation. Moreover, their effect depends on their chemical and mineralogical composition and also on the cement content replacement ratio. Glass is a common material with some environmental problems regarding recycling and landfilling. Some studies exist about its use as fine powder, like a pozzolan, in cement-based materials. However, there are also some problems related to its use as coarse aggregate in cementbased materials due to ASR development. This paper presents the results obtained in mortars exposed to 1M NaOH solution prepared with crushed glass as aggregate and as addition in cement substitution. The results reveal that ASR is reduced with the incorporation of glass as aggregate or addition, and its efficiency depends on its replacement content. This study shows that an incorporation of glass aggregates up to 20% in mass will generate no significant expansion when compared with concrete made with natural aggregates.
Year: 2013
Number Pages:
415-420pp.
Author(s): Serpa, D.; Santos Silva, A.; Soares, D.; Santos, M. B.; Brito, J.
: Materials Science Forum
Editor: Trans Tech Publications
Volume:
Vols. 730-732.
Keywords: Concrete; Pozzolanic reaction; Alkalisilica reaction; Waste-glass
Info
Characterization of Deleterious Expansive Reactions in Fagilde Dam
A monitoring system has been detecting progressive displacements in Fagilde dam, completed in 1984. Site inspection revealed the existence of random cracking, surface discoloration, and superficial dissolution of cement in the spillway surfaces and in the upstream face of the dam. The macroscopic signs of deterioration, which could be due to different mechanisms, showed an uneven distribution in the exposed surfaces of the structure. Crushed limestone and alluvial siliceous sand were used as aggregates. Alkaliaggregate reaction was considered to be the likely cause of concrete distress. In order to investigate the causes of cracking and of the movements registered in the wall, drill core sampling was performed and the concrete investigated for the occurrence of expansive reactions. Concrete petrography was complemented by other tests in order to assess the probable evolution of the reactions in the structure in the near future. Residual expansion tests, soluble alkalis evaluation, and unconfined compression tests were carried out. Alkaliaggregate reactions and internal sulfate reaction were considered to be the main causes of damage in the concrete. In this study, microscopy showed to be an essential tool in the identification of the main causes of deterioration.
Year: 2013
Number Pages:
299-312pp.
Author(s): Fernandes, I.; Santos Silva, A.; Piteira Gomes, J.; Tavares de Castro, A.; Noronha, F.; Ribeiro, M.
: Metallography, Microstructure, and Analysis Application and Innovation for Metals, Alloys, and Engineered Materials
Editor: Springer
Volume:
2.
Keywords: Internal sulfate reaction; Alkaliaggregate reaction; Laboratory tests; Microscopy; Displacement
Info
EIS study of amine cured epoxy-silica-zirconia sol-gel coatings for corrosion protection of the aluminium alloy EN AW 6063
The organic-inorganic hybrid sol-gel films which structure comprises interconnected inorganic and organic networks have been reported as an environmentally friendly anti-corrosion pre-treatment for several metals, including aluminium alloys. In this paper, an epoxy-silica-zirconia hybrid sol-gel coating was synthesized from glycidoxypropyltrimethoxysilane (GPTMS) and zirconium n-propoxide (TPOZ) precursors and applied to EN AW-6063 alloy by dip-coating. To promote the organic network formation through the epoxy group polymerization at room temperature, two types of amine crosslinkers were added during synthesis: diethylenetriamine (DETA), in different concentrations, and a tri-functional amino-silane. The evolution of the curing process and the corrosion behaviour of the coated aluminium alloy specimens were evaluated by Electrochemical Impedance Spectroscopy (EIS) in 0.5 M NaCl. The morphology and surface chemistry of the hybrid coatings were characterized by Energy Dispersive Spectroscopy (EDS) coupled to Scanning Electron Microscopy (SEM) and by Fourier Transform Infrared Spectroscopy (FTIR). The results obtained revealed that the sol-gel coatings with lower amine ratios required longer curing times, but showed the best anticorrosive performance with time. The increase in amine concentration has led to a more cross linked organic network, resulting in higher initial coatings resistance, however it has turned coatings more hydrophilic, prone to rapid degradation in water.
Year: 2013
Number Pages:
307-319.
Author(s): Fontinha, I. R.; Salta, M. M.; Zheludkevich, M.; Ferreira, M. G. S.
: Portugaliae Electrochimica Acta
Editor: Sociedade Portuguesa de Electroquímica
Volume:
31(6).
Keywords: Aluminium; Eis; Corrosion; Silane; Sol-gel hybrid coating
Info
Evaluation of Pozzolanic Reactivity of Artificial Pozzolans
Pozzolanicity is a very interesting issue regarding building materials, as a way to enhance mortars and concrete durability. This property results from the reaction between calcium hydroxide and silica and alumina based materials. Different types of natural and artificial pozzolans show pozzolanic activities that differ depending on the materials characteristics. Therefore, the study of this property, namely its reactivity with calcium hydroxide, reveals itself to be important in the selection of the type and content of these materials. This paper presents the results of several pozzolanic reactivity methods, applied to different pozzolanic materials. The selected pozzolanic methods include Chapelle method, Fratinni method and Strength Activity Index. Those tests have been applied to evaluate the reactivity of various kinds of artificial pozzolans. The correlation between the test methods are presented and discussed.
Year: 2013
Number Pages:
433-438pp.
Author(s): Pontes, J.; Santos Silva, A.; Faria Rodrigues, P.
: Materials Science Forum
Editor: Trans Tech Publications
Volume:
Vols. 730-732.
Keywords: Fly ash; Strenght activity index; Fratinni; Chapelle; Reactivity; Pozzolan; Metakaolin
Info
Microstructural changes of lime putty during ageing
The microstructural development of lime putty is widely recognized and commonly associated with an increase in quality. Many heritage institutions encourage the systematic application of lime putties in conservation; however, all the issues associated with age are not fully understood. Changes occur during storage underwater, which traditionally took place in pits to prevent carbonation. The properties of mortars, plasters, and decorative finishes formed from lime putties are intimately linked to manufacturing parameters such as storage time. The hydration of calcium oxide was investigated using an environmental scanning electron microscope with particular attention to the nucleation of calcium hydroxide crystals on the surface of calcium oxide. Crystal modifications were monitored. The results obtained confirm and quantify the influence of slaking time in the microstructure of lime putties that is also reflected in the current referred special characteristics of the mortars produced with them, such as greater plasticity, water retention, and reactivity of mortars. The results also emphasize that the most significant microstructural changes of the lime putties start to consolidate after 8 months of slaking and appear to continue to develop, even though at a slower rate, until at least 5 years.
Year: 2013
Number Pages:
1524-1532pp..
Author(s): Margalha, G.; Santos Silva, A.; Veiga, M. R.; Brito, J.; Ball, R.; Allen, G.
: Journal of Materials in Civil Engineering
Editor: American Society of Civil Engineers
Volume:
25.
Keywords: Microstructure; Slaking time; Ageing; Lime putty; Air lime
|
Comunicação
Info
Corrosion resistance evaluation of welded stainless steels in concrete
The corrosion resistance of both welded and unwelded bars of Fe-Cr-Ni and Fe-Cr-Mn austenitic stainless steel alloys embedded in concrete was studied. Welded bars have been transiently either in an active or passive condition revealing its vulnerability to pitting corrosion, while unwelded bars have shown a stable passive state. The corrosion of the welded bars is mostly caused by the existence of weld surface defects, and by galvanic effects which are more considerable in the welded high manganese alloys.
Year: 2010
Number Pages:
6.
Author(s): Correia, M. J.; Salta, M. M.; Fonseca, I. T. E.
Keywords: Welding; Corrosion prevention; New alloys; Stainless steel reinforcement
Info
Degradation of Concrete Bridges by Internal Expansive Reactions Portuguese Case Studies
In the last years some concrete bridges in Portugal have shown premature deterioration due to intensive concrete cracking development mainly attributed to internal expansive reactions. An important experimental program was conducted by Laboratório Nacional de Engenharia Civil (LNEC), a public institution of the Portuguese Ministry for Public Works, Transports and Housing, in order to diagnose the causes and also prognostic the long-term behaviour of the deteriorated concrete bridges. The research conducted has pointeded that the concrete cracking was mainly due to the occurrence of internal expansive reactions: alkali-silica reaction (ASR) and/ or delayed ettringite formation (DEF). The ASR was caused by the use of alkali reactive aggregates and the DEF by the high heat-curing temperature obtained during the setting and hardening in combination with the high portland cement content used in the concrete mix designs. Residual expansion tests were done in order to access the residual ASR and DEF reactivity. Measurements have been carried out with the methods normally used for ASR and DEF concrete testing: 38º C ± 2º C and 95% HR in the first case and 20º± 2º C and 100% HR for the second. Mostly of the bridges show residual capacity to continue the expansion due to ASR or DEF, which forced remedial measures against these expansive reactions, mainly associated with control of the ingress of water into concrete. This situation in Portugal led to conclude that new deterioration cases can occur. To avoid these causes of damage the design and construction of new structures must follow the new Portuguese preventive methodologies (developed by LNEC).
Year: 2010
Author(s): Santos Silva, A.; Gonçalves, A.; Salta, M. M.
Editor: IRF
Keywords: Recommendations; Bridges; Concrete; Delayed ettringite formation; Alkali-silica reaction
Info
Development of research related to alkali-silica reaction in concrete with recycled aggregates
Since there is a possibility of incorporating recycled aggregates (RA) as a complement to primary aggregates (PA) in concrete production, taking advantage of construction and demolition waste, there are some questions on the durability of concrete with recycled aggregates (CRA) that need to be answered. The durability of concrete with primary aggregates only (CPA) is conditioned, among other factors, by its degradation due to alkali-silica reactions (ASR). Since the first cases of ASR in CPA were identified, this expansive reaction has been a research theme resulting in the development of prevention and mitigation methodologies and in the comprehension of the chemical reactions involved. The present paper proposes to describe the current development of a research program on ASR in CRA based on an experimental campaign involving the production of CRA with different replacement ratios of coarse PA with coarse concrete RA, the use of different cement classes, and variations on the concrete curing conditions and on the reactivity of the mixes.
Year: 2010
Number Pages:
433-440pp.
Author(s): Santos, M. B.; Brito, J.; Santos Silva, A.
Keywords: Mitigation; Prevention; Alkali-silica reaction; Recycled aggregates
Info
Développement de matériaux alternatifs. Perspectives: exemples de projet de recherche au Portugal et au Canada
Le Laboratoire central des ponts et chaussées associé au réseau des Laboratoires des ponts et chaussées ainsi qu'à des partenaires extérieurs ont réalisé dans le cadre de l'opération de recherche « bétons environnementaux» des travaux visant à introduire cette problématique pour la formulation des bétons. Une réflexion sur les modalités d'application des méthodes ACV pour l'évaluation de l'impact environnemental des bétons a été menée. Un document de synthèse précise le contexte dans lequel un constituant alternatif d'un béton peut être développé et validé. En complément au volet méthodologique, le programme de recherche comporte un volet expérimental important comprenant notamment des travaux exploratoires sur des constituants alternatifs susceptibles de contribuer à la diminution de l'impact environnemental des bétons et dont le processus de développement est plus ou moins abouti. Cette journée de synthèse a pour objectif de présenter les principaux résultats obtenus. Elle s'articulera autour de 4 sessions : évaluation de l'impact environnemental d'un béton ; développement de matériaux alternatifs ; valorisation de sous-produits et recyclage ; des bétons environnementaux- application in situ.
Year: 2010
Number Pages:
13.
Author(s): Santos Silva, A.; Pavoine, A.
Keywords: Additions pouzzolaniques; Sous-produits; Additions minérales; Bétons environnementaux
Info
EIS study of hybrid sol-gel coatings on aluminium
Estudo por espectroscopia de impedância electroquímica das propriedades anti corrosivas de um revestimento híbrido (orgânico-inorgânico)obtido pelo processo sol-gel em função da quantidade de água de hidrólise adicionada.
Year: 2010
Number Pages:
1.
Author(s): Fontinha, I. R.; Salta, M. M.; Zheludkevich, M.; Ferreira, M. G. S.
Editor: Sociedade Portuguesa de Materiais
Keywords: Corrosão; Eis; Sol-gel; Hybrid coating
Info
Influence des additions minérales sur la RSI
La réaction sulfatique interne (RSI) est une cause de désordres susceptibles d'endommager assez sévèrement des ouvrages en béton. Les premiers cas sont apparus à l'Allemagne à partir de 1987 dans certaines pièces préfabriquées qui avaient été soumises à un traitement thermique inadapté à la formulation du béton. En France, les désordres ont été observés à partir de 1997 sur des ponts dont le béton avait été coulé en place et concernent aujourd'hui environ une soixantaine de structures. Il s'agit essentiellement de parties d'ouvrages massives (piles, chevêtre sur pile,
), mais aussi de quelques éléments préfabriqués, en contact avec l'eau ou soumises à une humidité.Le Laboratoire central des ponts et chaussées associé au Réseau des laboratoires des ponts et chaussées ainsi qu'à des partenaires extérieurs mènent depuis 2005 des recherches sur cette problématique afin de mieux connaître les moyens nécessaires pour concevoir des ouvrages exempts de RSI et de mieux gérer les ouvrages malades. L'objectif de cette journée est de présenter les dernières avancées ainsi que les nouvelles méthodes et guides techniques du LCPC.
Year: 2010
Number Pages:
10.
Author(s): Santos Silva, A.
Keywords: Cendres biomasse; Fumées de silice; Laitier; Filler calcaire; Metakaolin; Cendres volantes; Additions minérales; Rsi
Info
Inhibition of internal expansive reactions in cement based materials with mineral additions
The degradation of concrete structures caused by internal sulphate reaction, with delayed etringite formation (DEF) and alkali-silica reaction (ASR) is a problem that affects many concrete structures worldwide (Divet et al., 2004). When these reactions occur their effects are particularly dangerous since their reaction products are extremely expansive causing the cracking of the concrete, contributing for a large reduction in the lifetime of the structure and in some extreme cases forcing its demolition. Hence, there is an urgent need to find preventive methods that may inhibit such reactions in new concrete structures. Today, its well known that the use of supplementary cementicious materials, e.g. type II mineral additions, could sustain this degradation form. Moreover, their effect depends on the chemical and mineralogical composition and also the cement content replacement. This paper presents the findings of a long-term study (Santos Silva et al., 2006; Divet et al., 2006) on the expansion rate and microstructure of concretes with different amounts of mineral additions, like fly ash, metakaolin, ground granulated blast-furnace slag, silica fume and limestone filler. For this purpose different concrete compositions were produced by using the same cement type (CEM I 42.5R) and water/cement (w/c) ratio. The results of the blended-concrete compositions were compared with those of control compositions, and the conclusions were extracted
Year: 2010
Number Pages:
8.
Author(s): Santos Silva, A.; Soares, D.; Matos, L.; Salta, M. M.
Keywords: Limestone filler; Silica fume; Ground granulated blast-furnace slag; Metakaolin; Fly ash; Def; Ras
Info
Mitigação da RAS e DEF pela utilização de resíduos minas de tungsténio
Os danos causados pelas reacções expansivas de origem interna (REOI), que envolvem a reacção álcalis-sílica (RAS) e a reacção sulfática interna (RSI), assumem grande importância na durabilidade e desempenho das estruturas de betão. Estas reacções afectam várias estruturas em todo o mundo, sendo necessário encontrar formas de prevenir/inibir a ocorrência das REOI nas novas estruturas de betão. Este trabalho pretende avaliar o efeito da utilização de lamas residuais de uma mina de tungsténio na mitigação das reacções expansivas de origem interna (REOI). Para este efeito, foram fabricadas diferentes composições de argamassas, utilizando-se um cimento CEM I 42,5R, um agregado silicioso reactivo e diferentes teores de lamas residuais em substituição do cimento portland. Neste artigo apresentam-se os resultados de ensaios de expansibilidade aos álcalis e de evolução da microestrutura das argamassas estudadas. Os resultados obtidos apontam para que uma substituição de pelo menos 30% de cimento portland por lamas residuais seja eficaz na mitigação das RAS.
Year: 2010
Number Pages:
217-228pp.
Author(s): Sousa, S.; Santos Silva, A.; Velosa, A.; Rocha, F.
Editor: Palataforma para a Construção Sustentável
Keywords: Resíduos de minas; Ras; Mitigação; Construção sustentável; Betão
Info
Mitigação das reacções expansivas no betão: avaliação do efeito do uso de adições minerais em substituição de cimento
As adições minerais têm mostrado resultados contraditórios na mitigação das reacções expansivas de origem interna. No LNEC, e com co-financiamento do projecto FCT EXREACT, estão em curso estudos a longo prazo que visam o estudo e a aplicabilidade destes materiais na mitigação das reacções expansivas de origem interna.
Year: 2010
Number Pages:
10.
Author(s): Santos Silva, A.; Soares, D.; Matos, L.; Salta, M. M.; Ribeiro, A. C.; Gonçalves, A.
Keywords: Reacções expansivas; Adições minerais; Ras; Def
Info
Physico-chemical characterization of the plasters from the church of Santissimo Sacramento in Alcântara, Lisbon
The Santissimo Sacramento Convent, in Alcântara quarter, in Lisbon, was an innovative architectural project in the XVII century and one of the most important ecclesiastic structures at that period in Lisbon. An intervention aiming at the restoration of the monuments interior plasters was planned in 2009 and is presently being carried out. In this article the main results obtained in the physico-chemical characterization of the internal plasters from Santissimo Sacramento church in Lisbon are presented, including mortars, stuccos and pigments; the diagnosis methodology was applied for the evaluation of the state of conservation of the renders and the recommendations made for the repair mortars. The results obtained lead to the conclusion that the mortars are in very good condition, being composed by aerial calcitic lime with siliceous and basaltic aggregates, while the stuccos are constituted by gypsum and aerial calcitic lime and the decorative layers are of lime with some precious pigments too, such as ultramarine (lapislazzuli) and gildings.
Year: 2010
Number Pages:
345-357pp.
Author(s): Santos Silva, A.; Borsoi, G.; Veiga, M. R.; Fragata, A.; Tavares, M.; Llera, F.
Editor: RILEM Publications S.A.R.L.
Keywords: Plasters; Cultural heritage; Conservation; Historical mortars; Characterization
|
Books
Info
Materiais de interesse histórico que constroem o património edificado: Correlações, usos, paisagens
Os artigos que compõem esta edição foram criteriosamente selecionados e aprimorados, seguindo igual metodologia de trabalho do número anterior, contribuindo para compor um dossier temático de elevado interesse e qualidade. No seu conjunto, os vários textos sublinham o papel dos materiais históricos na construção multidimensional do território humanizado, ligando os aspetos tangíveis e intangíveis, transportando saber e gosto, tradição e inovação. Estes artigos, bem como os do primeiro volume, são também uma fonte reflexão e de conhecimento sobre alguns dos materiais de construção mais empregues no Património abrindo, nalguns casos, novas perspetivas para futuras investigações nesta área do conhecimento.
Year: 2022
Number Pages:
218p..
Author(s): Veiga, M. R.; Santos Silva, A.; Menezes, M.
: Cadernos do Arquivo Municipal
Editor: Câmara Municipal de Lisboa
Volume:
Vol. II, Nº 17.
Keywords: Calçada Portuguesa; Ouro Preto, Brasil; Baixa Pombalina; Mansardas; Fábrica de cerâmica Lusitânia; Lisboa; Mármore; Raul Lino; Azulejo; Património; Materiais de construção
Info
On the origin of majolica azulejos production in Portugal. nº 2 - vol II.
Vários
Year: 2019
Number Pages:
97p.
Author(s): Pais, A.; Mimoso, J.; Rosmaninho, R.; Esteves, L.; Morais Pereira, S.; Antunes, M.; Cardoso, A.; Mirão, J.; Marques, A.; Ferreira, M.; Candeias, A.; Valona, R.; Morna, T.; Simões, J.
: Estudos em Cerâmica Vidrada Patrimonial
Editor: LNEC
Keywords: PT; Physical-chemical characterization; Azulejo; Manufacture; Glazed ceramics; Historic heritage
Info
Characterization of decorative Portuguese gypsum plasters from the 19th and 20th centuries: the case of the Bolsa Palace in Oporto
The use of gypsum plaster for the interior coating of walls and ceilings in the Portuguese architecture was particularly expressive in the period between the XVIII and the XX century. However, information about this important heritage is almost nonexistent, which is leading to a rapid loss of important patrimony. In this paper the results of the characterisation of five gypsum plaster samples from the second half of the XIX century belonging to the Arabian Room of the Bolsa Palace, located in Oporto, North of Portugal, are presented and discussed. XRD and TGA-DTA techniques were used to establish the mineralogical composition, and the relative proportions of the binders. Optical microscopy and FESEM-EDS observations were performed both in fractured and polished surfaces in order to determine the stratigraphy and the composition of individual layers. The results of this characterisation work showed that the plasters used were mainly composed of gypsum and hydrated lime in different proportions a feature that was correlated with the application techniques of the decorative elements analyzed - and allowed the determining of the restoration interventions they had already been submitted to. Some physical properties like the dynamic modulus of elasticity and capillary absorption were also determined, and a correlation between the results obtained was established with previous studies performed by the authors.
Year: 2012
Number Pages:
141-151pp.
Author(s): Freire, T.; Santos Silva, A.; Veiga, M. R.; Brito, J.
Editor: Springer
Volume:
Volume 7, RILEM Bookseries.
Keywords: Capillary absorption; Microscopy; Tga-dta; Xrd; Characterisation; Gypsum plasters
Info
Diagnosis, characterization and restoration of the internal renders of Santíssimo Sacramento church in Lisbon
The Santíssimo Sacramento Convent in the Alcântara quarter of Lisbon is one of the most important ecclesiastical structures of the Filipino Period (1580- 1640), showing an innovative architectural layout. An intervention aiming at the repair and restoration of the interior plasters of the Santíssimo Sacramento Church was performed in 2009 and 2010. To support the restoration plan, a physical, mechanical and chemical-mineralogical characterization of the internal plasters of the church was carried out. In this paper the main results are presented, such as various types of plasters, mortars, stuccos and pigments; and also the nature of the main anomalies were identified and characterized. The results obtained contributed to the identification of the main decorative programs characterized by the use of different materials and techniques. The mortars are in very good condition, being composed of aerial calcitic lime with quartzitic and basaltic aggregates. The stuccos are comprised by gypsum and non-hydraulic lime, while the decorative layers features lime with some precious pigments, such as ultramarine (lapislazzuli) and gold-foil gildings. The plaster conservation and restoration works were performed with compatible repair materials selected according to the physical-chemical characterization and on the evaluation of the conservation state.
Year: 2012
Number Pages:
175-194pp.
Author(s): Santos Silva, A.; Borsoi, G.; Veiga, M. R.; Fragata, A.; Tavares, M.; Llera, F.; Barreiros, B.; Teixeira, T.
Editor: Springer
Volume:
Volume 7, RILEM Bookseries.
Keywords: Pigments; Stuccos; Mortars; Plasters
Info
AS REACÇÕES EXPANSIVAS INTERNAS NO BETÃO. Prevenção dos riscos e gestão das estruturas afectadas
A degradação de estruturas de betão por reacções expansivas internas é uma patologia que, não sendo relativamente recente a nível internacional, tem vindo a manifestar-se duma forma crescente nos últimos anos em Portugal. Esta patologia tem afectado vários tipos de estruturas de betão, algumas de grande importância estratégica, nomeadamente grandes barragens e obras de arte (pontes e viadutos). A título de exemplo referem-se os casos do Viaduto Duarte Pacheco, e as Barragens de Alto-Ceira e Santa Luzia, alguns dos quais obrigaram a intervenções de elevado custo. Esta forma de degradação, que engloba a reacção álcalis-sílica (RAS) e a reacção sulfática interna (RSI), quando ocorre numa estrutura é particularmente nefasta porque está relacionada com a formação de compostos expansivos que provocam a fissuração do betão, contribuindo decisivamente para a diminuição da vida útil da estrutura, podendo em alguns casos obrigar à sua demolição. Associada a esta situação, acresce o facto de não se dispor actualmente dum método totalmente eficiente e económico de combater esta forma de degradação. Deste modo, para garantir os tempos de vida útil preconizados para as novas construções devemse adoptar medidas preventivas para evitar ou minimizar os efeitos da ocorrência deste tipo de reacções expansivas nas estruturas de betão. Em Portugal, medidas preventivas destas reacções expansivas internas estão contidas na Especificação LNEC E 461, citada na NP EN 206-1 Betão. Parte 1: Desempenho, especificação, produção e conformidade, a qual inclui a fixação de níveis de prevenção de acordo com a categoria de risco e exposição ambiental do elemento ou da estrutura de betão. Estas medidas passam por uma caracterização dos factores condicionantes destas reacções nos constituintes do betão e pela aplicação de medidas para a sua inibição. Neste particular, a utilização de adições minerais em substituição parcial do clínquer portland, é uma medida que além de diminuir o calor de hidratação, permite a redução da alcalinidade da solução intersticial do betão e contribui ainda para reduzir a quantidade de sulfatos no betão, evitando assim a formação de produtos expansivos. Actualmente é já conhecido que as adições minerais do tipo II, em substituição parcial do cimento no betão e em quantidade suficiente, podem mitigar os efeitos destas reacções. A acção destas adições minerais depende, no entanto, da sua composição e reactividade pozolânica.Apesar dos bons resultados já demonstrados por algumas adições, nomeadamente as cinzas volantes, o seu uso pode estar comprometido a curto/médio prazo, tendo em conta a cada vez maior preocupação, por parte da maioria dos Países, na utilização de renergias limpas. Esta tendência terá como consequência uma diminuiçãtt ou mesmo o esgotamento da produção de alguns subprodutos industriais. No caso dos produtos naturais, é previsível um agravamento das restrições ambientais associadas à sua exploração e tratamento. Foi neste contexto que se iniciou no LNEC, em colaboração com o Laboratoire Central des Ponts et Chaussées de Paris e as Universidades de Aveiro, Minho e Évora, um projecto de avaliação da utilização de novos materiais com características pozolânicas, capazes de responderem às necessidades da indústria do betão a curto/médio prazo. Este projecto, que contou com o apoio da Fundação para a Ciência e Tecnologia (Projecto PTDC/CTM/65243/2006 EXREACT Mitigação de reacções expansivas deletérias em estruturas de betão) visa ainda o aperfeiçoamento de metodologias de diagnóstico e prognóstico da ocorrência de reacções expansivas internas em estruturas de betão existentes. Os resultados do trabalho realizado no decorrer do projecto têm vindo a ser divulgados em artigos e comunicações em seminários nacionais e internacionais, mas também através duma página Web (http://www-ext.lnec.pt/EXREACT/index.html) e com a organização de reuniões como a do presente Workshop, que contou com o apoio do LNEC, da Comissão Organizadora do REABILITAR 2010 - Encontro Nacional de Conservação e Reabilitação de Estruturas e dos oradores convidados. Este Workshop visa apresentar os últimos desenvolvimentos sobre os aspectos da prevenção, modelação e reparação, proporcionando uma oportunidade para a compartilha de ideias e soluções para a gestão das estruturas afectadas por RAS e/ou RSI.
Year: 2010
Number Pages:
143.
Author(s): Santos Silva, A.; Gonçalves, A.; Divet, L.; Pavoine, A.; Germain, D.; Appleton, J.
Editor: LNEC
Keywords: Reparação; Modelação; Gestão; Prevenção; Def; Ras; Betão; Reacções expansivas
|
Capítulo de Livro
Info
Analysis of the behavior of original air lime mortars used in structural brick masonry walls of ancient buildings
The growing interest in preserving the built heritage is a driving force towards the search for new rehabilitation solutions compatible with the original construction techniques of ancient buildings. For the design of an adequate reinforcement solution, it is necessary to know in detail the building to be rehabilitated, as well as its original constructive solutions and materials.This paper presents the results of an experimental campaign on samples of air lime-based laying and coating mortars, extracted from an old masonry building in the historic center of Lisbon, built in 1910, during the rehabilitation works. The different parameters analyzed allow for the composition characterization and evaluation of their mechanical, physical and chemical properties. Based on this characterization, the influence of these mortars on the overall behavior of load-bearing walls of buildings belonging to the typology under study is also evaluated.Considering the results obtained in the characterization tests for the mortars in study, it was verified that the binder used in both mortars was air lime. The values for compressive strength, modulus of elasticity and the curves obtained in the capillarity and drying tests, are also compatible with this type of mortars. It was determined that the mortars are similar in terms of physical and mechanical characteristics, to Portuguese mortars studied in current buildings of the same historical period. This type of information is crucial in a structural analysis and allows to identify materials compatible with the original ones that can be used in rehabilitation interventions.
Year: 2023
Number Pages:
15p..
Author(s): Candeias, P.; Ferreira, J.; Santos Silva, A.; Veiga, M. R.; Mera Marques, A.
: Conservation and Restoration of Historic Mortars and Masonry Structures
Editor: Springer
Keywords: Characterization tests; Air lime mortars; Structural brick masonry walls; Ancient buildings; Conservation and rehabilitation
Info
CDW as sources of CO2 absorption
Cementitious materials have a considerable global warming footprint. This is due mainly tothe cement incorporated. For a tonne of cement produced other 800 kg of CO2 [1] are releasedinto the atmosphere.According to the European Sustainable Development Goals, cement industry should becomecarbon neutral by 2050. To meet this goal, the European Cement Association (Cembureau)developed a Roadmap with specific guidelines by 2050 based on five approaches (5C). Thefirst four are focused on improvements in clinker production, cement formulation,construction processes and concrete formulations. The last 5C is re-carbonation of thecementitious materials.This research investigates the CO2 absorption capability of recycled aggregates (RA) fromconstruction and demolition wastes (CDW), when submitted to a forced carbonation. It isknown that CDW still have some potential to CO2 capture, which is a long-term and securecarbon storage. For that purpose, several CDW were collected from recycling plants, fromselective demolitions and from concrete plants.It was concluded that RA when submitted to forced carbonation absorb between 47 to 315 kgof CO2 per tonne of cement paste, which has a potential to meet the re-carbonation targetsestablished by the roadmaps to carbon neutrality.
Year: 2023
Number Pages:
243-257pp..
Author(s): Martins, I. M.; Santos Silva, A.; Veiga, M. R.; Infante Gomes, R.; Bastos, D.; Pederneiras, C.; Farinha, C.
: Proceedings of the V International Conference Progress of Recycling in the Built Environment
Editor: RILEM
Volume:
RILEM Proceedings PRO 137.
Keywords: Recycled aggregates; Forced carbonation; CO2 absorption; CDW
Info
Characterization of mortars and concretes from the Mirante da Quinta da Azeda, Setúbal (Portugal). A case study from the beginning of the 20th century
The Mirante da Quinta da Azeda, in Setúbal (Portugal), is a peculiar observation tower built in the early 20th century, and one of the first examples in which reinforced concrete was applied in Portugal. It has an unusual architectural configuration, displaying elements of great slenderness. In the scope of the CemRestore research project - Mortars for the conservation of early 20th century buildings: compatibility and sustainability, several mortar and concrete samples were collected from this structure and were characterized using a combination of mineralogical, microstructural, physical, and mechanical techniques, including XRD, petrography, SEM-EDS, open porosity, capillarity coefficient, compressive strength, and ultrasonic pulse testing. In this paper, the main characterization results are presented and discussed. The results show that all structural and decorative samples are made with Portland cement, while one rendering mortar is lime-based. The sand is mostly siliceous whereas pebbles and crushed limestone can be found as coarse aggregates in concrete samples. This characterization allows for broadening the scientific knowledge about the materials of that period used in Portugal, also enabling the establishment of the requirements to be met by mortars and concrete to be used in the repair of this distinct structure.
Year: 2023
Number Pages:
243-257pp..
Author(s): Velosa, A.; Veiga, M. R.; Santos Silva, A.; Lopes dos Santos, A. R.; Almeida, L.
: Conservation and Restoration of Historic Mortars and Masonry Structures
Editor: Springer
Keywords: Portugal; Characterization; Concrete; Mortar; 20th century
Info
Evaluation of the hygroscopic and CO2 capture capacities of earth and gypsum-based plasters
Earth mortars and gypsum mortars present ecological advantages compared to mortars made with other common binders. When applied as plasters, they are also referred as having advantages in improving comfort and indoor air quality. For earth plasters, this improvement is associated with the hygroscopic capacity of the clay minerals, which promotes high sorption and desorption capacity of water vapor. So, earth plasters can contribute to the regulation of the indoor relative humidity. Another important advantage of plasters could be their ability to capture carbon dioxide (CO2). In the present study, the sorption and desorption performance, and the capacity to capture CO2 by earth and gypsum plasters are evaluated. It is confirmed that the earth plaster has the greatest sorption and desorption capacity, but also higher CO2 capture capacity than gypsum plaster. This confirmation opens new perspectives for the use of functionalized plasters that guarantee greater control of air quality inside buildings.
Year: 2023
Number Pages:
207-215pp..
Author(s): Faria, P.; Gomes, I.; Santos Silva, A.; Santos, T.
: Conservation and Restoration of Historic Mortars and Masonry Structures
Editor: Springer
Keywords: Mortar; Indoor air quality; Hygroscopicity; Gypsum; Clayey earth; CO2 capture
Info
Os revestimentos e os acabamentos do Centro Histórico de Coimbra. Um contributo para o seu estudo
Coimbra apresenta um elevado valor arquitetónico demonstrado pelos 36 imóveis, conjuntos ou sítios (22 monumentos nacionais e 14 imóveis de interesse público) actualmente classificados (DGPC, 2015) sendo a maioria deles localizados no Centro Histórico de Coimbra (CHC) e zona alta da cidade. No âmbito do projecto POCI/HEC/60371/2004 Bases para o restauro dos revestimentos históricos do Centro Histórico de Coimbra, foi feito um levantamento das existências cromáticas existentes no CHC-Alta (zona de edifícios de habitação da Alta de Coimbra, Figura 3.1), a partir do qual se seleccionaram edifícios que ainda apresentavam vestígios de pinturas em várias camadas, o mais antigas possível.
Year: 2017
Number Pages:
49-74pp.
Author(s): Catarino, L.; Gil, F.; Duarte, T.; Veiga, M. R.; Santos Silva, A.
Editor: Almedina
Keywords: Cal calcítica; Cal dolomítica; Argamassas; Caracterização; Estratigrafia; Centro Histórico de Coimbra; Revestimentos
|
Tese de Doutoramento
Info
Revestimentos nanoestruturados para protecção de liga de alumínio
Os revestimentos híbridos nanoestruturados apresentam um elevado potencial no âmbito da protecção anticorrosiva dos metais, prevendo-se que no futuro estes revestimentos possam, não só substituir os tratamentos à base de crómio usados na indústria do tratamento de superfícies metálicas para protecção anticorrosiva, como também evoluir para sistemas integrados multifuncionais que dispensem o pré-tratamento e sejam mais amigos do ambiente. O processo sol-gel usado para a obtenção destes revestimentos permite, através da combinação de diferentes precursores e da manipulação das condições de síntese desenhar e optimizar a estrutura química e a funcionalidade dos revestimentos nanoestruturados com o objectivo de obter as propriedades desejadas para uma determinada aplicação. O estudo apresentado no presente trabalho teve como objectivo principal a optimização de revestimentos híbridos nanoestruturados obtidos pelo processo sol-gel para a protecção anticorrosiva de uma liga de alumínio frequentemente utilizada na construção civil. Para alcançar este objectivo foram preparados diversos revestimentos híbridos nanoestruturados e aplicados na liga de alumínio EN AW-6063, cujo processo de síntese foi optimizado variando parâmetros como a composição, processo de cura e condições reaccionais sol-gel, visando a obtenção de revestimentos com propriedades anticorrosivas melhoradas. Posteriormente, foi feita uma avaliação do comportamento à corrosão dos revestimentos optimizados em diferentes condições corrosivas, individualmente e como parte integrante de um sistema de protecção anticorrosiva usualmente aplicado em ligas de alumínio para fins arquitecturais. No presente documento é apresentada uma revisão bibliográfica da aplicação deste tipo de revestimentos na protecção anticorrosiva, seguindo-se a descrição detalhada dos procedimentos experimentais do estudo, nomeadamente, os materiais e os procedimentos para obtenção e caracterização dos revestimentos estudados, a apresentação dos resultados obtidos no decurso do desenvolvimento experimental realizado, sua interpretação, discussão e as conclusões parciais mais relevantes. No final, resumem-se as principais conclusões obtidas no estudo e faz-se uma avaliação global da aplicabilidade dos revestimentos optimizados na protecção anticorrosiva de ligas de alumínio no âmbito da construção civil, e indicam-se necessidades de desenvolvimentos futuros.
Year: 2012
Number Pages:
256.
Author(s): Fontinha, I. R.
Keywords: Corrosão; Liga de alumínio; Sol-gel; Revestimentos híbrido nanoestruturados
Info
Passivação do aço inoxidável no betão
Nesta dissertação, estudou-se o comportamento electroquímico de cinco ligas austeníticas de aço inoxidável em meio alcalino, nomeadamente duas ligas de Fe-Cr-Ni (1.4301?SS0 e 1.4436?SS4) e três novas ligas de elevado teor em manganês Fe-Cr-Mn (SS1, SS2 e SS3). Os estudos incidiram na avaliação da resistência à corrosão das ligas, em soluções alcalinas e no betão, e na caracterização das propriedades dos filmes de passivação sob influências várias, designadamente, condições de estabilização (electrólito, tempo e potencial de formação do filme), composição e microestrutura das ligas, soldadura e estado da superfície do aço. O estudo da capacidade diferencial em função do potencial mostra o comportamento dos filmes de passivação como semicondutores tipo-n e tipo-p, respectivamente, para valores anódicos e catódicos relativamente aos potenciais de banda plana, possibilitando a determinação das suas propriedades electrónicas. Estas traduzem as principais diferenças dos dois grupos de ligas, sendo que as ligas de Fe-Cr-Mn mostram uma menor razão da densidade de aceitadores com a densidade total de portadores de carga, do que as ligas de Fe-Cr-Ni, e um nível de doadores profundo, cuja ionização depende do potencial aplicado. Todas as ligas revelaram uma elevada resistência à corrosão nos diferentes meios, sendo a sua estabilidade especialmente dependente do acabamento superficial do aço e da existência de condições que promovam a corrosão intersticial. A soldadura das ligas induziu a formação de picadas instáveis, cuja repassivação foi desfavorecida em duas das ligas de Fe-Cr-Mn (SS1 e SS3). A presença de fissuras no betão demonstrou a despassivação das ligas e a susceptibilidade à corrosão sob tensão da liga SS1 no betão. As propriedades dos filmes de passivação, nomeadamente as densidades dos portadores de carga, que podem ser correlacionadas com a composição e a microestrutura das ligas, justificam as diferenças no comportamento electroquímico das ligas de Fe-Cr-Ni e de Fe-Cr-Mn. Para além das diferenças promovidas pelos teores de níquel e de manganês e pela ferrite, a maior resistência à corrosão das ligas SS2 e SS4, respectivamente, quando comparadas com as restantes ligas de Fe-Cr-Ni (SS0) e Fe-Cr-Mn (SS1 e SS3), é devida à presença do molibdénio e seus eventuais efeitos sinergéticos com o crómio e azoto.
Year: 2009
Author(s): Correia, M. J.
Keywords: Corrosão; Propriedades semicondutoras; Filme de passivação; Aço inoxidável
|
Dissertação de Mestrado
Info
Caracterização de argamassas tradicionais e históricas de edifícios religiosos do Alentejo
O estudo da composição de argamassas antigas, que implica usualmente a utilização de técnicas de caracterização físico-química, mineralógica e microestrutural, desempenha um papel fundamental para a preservação do património cultural, permitindo obter um conhecimento bastante profundo sobre os seus constituintes e revelando detalhes importantes sobre as técnicas de construção, eventuais reparações e o estado de conservação e desempenho das mesmas. Neste trabalho foram analisadas argamassas provenientes de quatro edifícios religiosos da região do Alentejo, nomeadamente a Sé Catedral de Évora (Séc. XIII-XVII), a Igreja de Nossa Senhora da Assunção em Elvas (Séc. XVI), a Igreja Matriz de Mértola (Séc. XII) e o Conjunto Monumental de Amieira do Tejo (Séc. XIV-XVI). A metodologia de caracterização empregue recorreu a diversas técnicas, nomeadamente difracção de raios X (DRX), análise termogravimétrica (ATG), microscopia óptica (MO), microscopia electrónica de varrimento acoplada a espectroscopia de raios X por dispersão de energias (MEV-EDS), espectrofotometria de absorção atómica (EAA), potenciometria, gravimetria, sorção de água por capilaridade, resistência mecânica, porosimetria de mercúrio e a adsorção de azoto a 196 ºC. A aplicação da metodologia proposta permitiu determinar a composição e o estado de conservação das diversas argamassas, tendo-se constatado que nas argamassas da Sé Catedral de Évora e da antiga Sé de Elvas foram utilizados dois tipos de ligantes aéreos, cal calcítica e cal dolomítica, sendo o primeiro tipo o predominante. Nos casos de estudo da Igreja Matriz de Mértola e do Conjunto Monumental de Amieira do Tejo, as argamassas apresentam um ligante essencialmente calcítico. Verificou-se que os agregados utilizados são correlacionáveis com a litologia local de cada caso de estudo. As argamassas apresentam diferentes proporções de agregado, e nos casos de estudo da Sé Catedral de Évora, antiga Sé de Elvas e Igreja Matriz de Mértola foram utilizados fragmentos cerâmicos como aditivos.
Year: 2009
Author(s): Adriano, P.
Info
Estabilidade stabilidade de taludes em rochas silto-argilosas
Os fenómenos de instabilidade de taludes são frequentemente causa de acidentes humanos e materiais constituindo por esse motivo um problema geotécnico de maior importância. Os estudos dos movimentos de terra, são relativamente morosos e complexos, uma vez que é necessário ter em atenção muitos factores, quer relacionados com características internas ao maciço, ou seja, características geológicas e geotécnicas, quer com acções externas. Os estudos das instabilidades de taludes ou vertentes naturais, têm como objectivo avaliar avaliar a perigosidade associada à sua ocorrência, os correspondentes riscos e definir medidas de prevenção e de controlo dos movimentos de terra que possam ocorrer. As modificações geológicas e climáticas experimentadas ao longo do tempo geram uma modificação constante na geometria dos taludes devido à sua sucessiva adaptação a novas condições de equilíbrio. Geralmente, as áreas mais propícias à ocorrência deste tipo de movimentos, correspondem a zonas montanhosas, escarpadas e sujeitas a elevada precipitação ou a condições hidrogeológicas desfavoráveis. Deste modo, a presente dissertação tem por objectivo fazer uma abordagem da problemática associada à instabilidade de taludes em rochas silto-argilosas, dando uma panorâmica das técnicas de engenharia usadas para o controlo dessas situações e salientando-se algumas técnicas de biorremediação apropriadas para o controlo de movimentos superficiais. Os temas abordados são explicados com uma aplicação a um caso real de estudo em Portugal.
Year: 2008
Author(s): Matos, L.
|
Relatório Científico
Info
Aplicação de titânio e suas ligas na construção - Estudo da corrosão galvânica do par aço inoxidável/titânio em meio alcalino
Neste relatório, após uma introdução em que se resumem as características do titânio e das suas ligas mais relevantes para a aplicação como material de construção e se apresentam aplicações destes materiais na construção civil, apresentam-se resultados de um trabalho experimental preliminar desenvolvido com o objectivo de estudar a corrosão galvânica de aço inoxidável quando associado a titânio, em meio alcalino, a várias temperaturas.
Year: 2007
Number Pages:
69pp.
Author(s): Pereira, E. V.; Ferreira, P.
Info
Projecto SCORBA - Desenvolvimento de um sensor de resistividade para monitorização da corrosão no betão armado
N/A
Year: 2007
Number Pages:
49pp.
Author(s): Pereira, E. V.; Santos, J.
|
|
|
Outro
Info
Effect of inorganic content on the performance of anticorrosive hybrid sol-gel coated EN AW-6063 alloy
The organic-inorganic hybrid sol-gel films have been reported as an effective anti-corrosion and environmentally friendly alternative to Cr(VI) pre-treatment for aluminium alloys. These hybrid materials, constituted by nanostructured polymer networks, interconnecting organic and inorganic materials, are of interest because the synergic effect on the mechanical and chemical properties achieved. The organic components impart flexibility, density and functional compatibility with organic coatings, while inorganic components impart hardness, resistance to abrasion and improve adhesion to the metal substrate. The sol-gel process used to obtain these coatings, through a series of simultaneous hydrolysis and condensations reactions between alkoxide precursors, yields highly adherent, chemically inert films on metal substrates and allows the variation of the different synthesis parameters to achieve coatings with optimized properties. In this work, hybrid films were synthesized from glycidoxypropyltrimethoxysilane (GPTMS) and zirconium n-propoxide (TPOZ) precursors, using different amounts of TPOZ (10%, 20%, 30%) and applied to EN AW-6063 alloy by dip-coating, aiming to achieve the best anticorrosive coating. The corrosion behaviour of aluminium specimens coated with these films was evaluated by Electrochemical Impedance Spectroscopy (EIS) in 0.5 M NaCl solution for 63 days. The results obtained revealed that the hybrid films provided effective corrosion protection, exhibiting good barrier properties, however, it was found that 30% of TPOZ led to a marked decrease in the barrier properties with time. The hybrid films prepared were also characterized by Energy Dispersive Spectroscopy (EDS), Scanning Electron Microscopy (SEM), Infrared Spectroscopy and Thermogravimetric Analysis (TGA-DTG) in order to relate their morphology and chemical structure with the corrosion behaviour.
Year: 2011
Author(s): Fontinha, I. R.; Salta, M. M.; Zheludkevich, M.; Ferreira, M. G. S.
Editor: Materais 2011 - SPM
Keywords: Aluminium; Corrosion; Sol-gel; Hybrid coating
Info
Characterization of the concrete alkali reactivity of granitoid and dolomitic aggregates
The general designation of internal expansive reactions includes the alkali-silica reaction (ASR) and the internal sulfate attack by delayed ettringite formation (DEF). These reactions are characterized by the formation of expansive compounds in hardened concrete and consequent cracking of the structure. In Portugal, the number of structures, mainly dams and bridges, affected by ASR is very significant and in some cases require considerable investment in rehabilitation interventions. Moreover, previous research has shown that the use of some aggregates, initially regarded as inert, can cause problems, proving the need for further insight on the role of aggregates and prevent the occurrence of ASR in constructions. The economic value of various types of structures (e.g. dams, bridges, airfields) and the high costs related to structural degradation including losses of functionality and the permanent or temporary unavailability (for repair and rehabilitation) could be an important overthrow. Thus thorough understanding of the earth materials requirements for concrete manufacture are of vital economic importance in view of the prevention of deterioration and aging of structures whose longevity and functionality must be guaranteed. It is imperative to provide the concrete producers with the necessary knowledge in order to avoid this type of concrete degradation. Particularly important is the recently approved Lisbon-Madrid High Speed Train railway construction. This expensive operation will require large quantities of aggregates for the construction of bridges and other concrete infrastructures. Three main sources of raw materials will be considered for the study: St. Eulalia, Montemor and Cano. These quarries are already major exploitation sites separated by 50 km and not far from the future High Speed Train railway. Two of them are granitoid rocks but the raw material from St. Eulalia is richer in quartz and poorer in ferromagnesian minerals than the Montemor aggregates. The enrichment in calcium of feldspar goes together with the iron and the magnesium. The Cano aggregates are very different materials. The main lithology is a dolomite rock with local microscopic enrichments in phyllosilicates and very deformed quartz. Mineralogical and textural characterization of the aggregates was done by optical microscopy. The crystallinity of quartz was also evaluated by XRD and FTIR. The aggregates were also studied by accelerated expansion mortar-bar and concrete-prism tests to evaluate their potentially alkali-reactivity. The relationship between aggregates characteristics and their behaviour in what concerns to alkali reactivity will be discussed.
Year: 2010
Number Pages:
1.
Author(s): Sabino, N.; Santos Silva, A.; Menezes, A. P.; Moita, P.; Candeias, A.; Mirão, J.
Editor: Department of Mineralogy, Geochemistry and Pterology, University of Szeged
Keywords: Dolomites; Granites; Alkali reactivity; Asr
|