Publications

The Baixo Sabor hydroelectric power plant, located in the northeast of Portugal, includes a reservoir with a storage capacity of 630 million m3 of water created by a concrete double-curvature arch dam, 100 m high, which was equipped with a 20-channel vibration based structural health monitoring system.This paper, apart from describing the dam, presents the main characteristics of the monitoring system and the results obtained during the first 6 months of operation and the first filling of the reservoir. These results include in particular the characterization of the accelerations amplitude and the evolution of the dam modal parameters (natural frequencies, modal damping ratios and mode shapes). It is particular interesting to observe the influence of the water level on the modal parameters and the development of statistical models to mitigate this effect.

Earthquakes cause severe damage to masonry structures due to inertial forces acting in the normaldirection to the plane of the walls. The out-of-plane behavior of masonry walls is complex anddepends on several parameters, such as material and geometric properties of walls, connectionsbetween structural elements, the characteristics of the input motions, among others. Differentanalytical methods and advanced numerical modeling are usually used for evaluating the out-ofplanebehavior of masonry structures. Furthermore, different types of structural analysis can beadopted for this complex behavior, such as limit analysis, pushover, or nonlinear dynamic analysis.Aiming to evaluate the capabilities of different approaches to similar problems, blind predictionswere made using different approaches. For this purpose, two idealized structures were tested on ashaking table and several experts on masonry structures were invited to present blind predictions on theresponse of the structures, aiming at evaluating the available tools for the out-of-plane assessment ofmasonry structures. This article presents the results of the blind test predictions and the comparisonwith the experimental results, namely in terms of formed collapsed mechanisms and control outputs(PGA or maximum displacements), taking into account the selected tools to perform the analysis.

The analysis of the shaking table test of a 3-wall stone masonry structure performed with a discreteelement model is presented. The numerical model, created with the code 3DEC, employed a rigidblock representation and a Mohr-Coulomb joint model. Joint stiffness calibration to match theexperimental natural frequencies is discussed, as well as the boundary conditions to simulate theshake table. Comparisons are made with themeasured displacements at key locations, and themodesof deformation and fracture of the walls. The DEM model was able to reproduce important features ofthe shaking table tests. The experimental deformation and near collapse patterns were clearlyidentifiable in the numerical simulations, which produced displacements within the observed ordersof magnitude, for the various levels of excitation.

This paper presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and

The 1:10 scale model of the 15th century Mustafa Pasha Mosque in Skopje, that underwent a comprehensiveshake table program, is modeled by the discrete elements approach. A rigid block model withnonlinear behavior concentrated at the joints was developed and calibrated by comparison with theobserved response. Time domain analyses of the discrete model were performed under the various levelsof dynamic excitation used in the shake table test. Under the lower levels of input, the time and frequencydomain characteristics of the shake table experimental response were fairly well simulated by thenumerical model. This model also predicted well the zones and the level of damages. For the higher inputlevels, the comparison was less satisfactory. Overall, the discrete element approach showed the capabilityto handle the dynamic nonlinear modeling of relatively complex masonry structures.

This work investigates tensile crack propagation in concrete gravity dams by using some recently developed numerical techniques (crack-path field and strain injection techniques). The work carefully addresses aspects related to mesh independence, robustness and computational cost, which are the main issues in fracture modeling. The novel technique consists of a procedure to insert, in the selected domain areas, specific strain fields for enhancing the performance of the underlying finite elements in modeling fracture. Representative numerical simulations of concrete dams show the accuracy and robustness of the methodology.

Block models have been shown to provide a realistic representation of the behavior of many types of masonry structures under static and dynamic loads. When the strength of the units is such that movements along the joints govern the behavior, it is acceptable to make the simplifying assumption that blocks act as rigid bodies. This assumption is particularly useful when dealing with seismic problems, for which the computational times for time domain analysis may be substantial. In this paper, the application of discrete element models for dynamic analysis of masonry structures is addressed. The emphasis is on the seismic behavior of block stone masonry, but the treatment is general to cover other types of masonry. First, the assumptions involved in the choice of a block representation are discussed, stressing in particular the case of rigid block models. Numerical issues are examined, including contact models, calculation of natural frequencies, time stepping algorithms, damping and boundary conditions. A review is presented of modeling examples published in the literature for various types of masonry structures. The choice of numerical representation and its main features are discussed for each case.

Much research in recent years has focused on the seismic analysis of concrete and earthfill dams,and few works have addressed the case of masonry dams. The structural behavior of masonrydams is controlled essentially by its discontinuous nature, which may induce significant nonlinearresponse during an intense earthquake. In this article, a numerical tool based on the Discrete ElementMethod is presented, aimed at the static, dynamic, and hydromechanical analysis of masonry gravitydams. The use of discontinuous models is mandatory for the study of failure mechanisms involvingthe masonry discontinuities, the dam-rock interface or the rock mass joints. The Discrete ElementMethod is able to assemble continuous and discontinuous meshes simultaneously in the same model,providing a versatile tool to consider various assumptions and levels of analysis, ranging from simplifiedto detailed structural representations. A comprehensive study of the seismic behavior of LagoaComprida Dam, located in Portugal, is presented. Both continuous and discontinuous models weredeveloped to assess the main failure mechanisms, including overstress, partial and global sliding,and overturning.

The analysis of the shaking table test of a 3-wall stone masonry structure performed with a discreteelement model is presented. The numerical model, created with the code 3DEC, employed a rigidblock representation and a Mohr-Coulomb joint model. Joint stiffness calibration to match theexperimental natural frequencies is discussed, as well as the boundary conditions to simulate theshake table. Comparisons are made with themeasured displacements at key locations, and themodesof deformation and fracture of the walls. The DEM model was able to reproduce important features ofthe shaking table tests. The experimental deformation and near collapse patterns were clearlyidentifiable in the numerical simulations, which produced displacements within the observed ordersof magnitude, for the various levels of excitation.

A computationally affordable modeling of dynamic fracture phenomena is performed in this study by using strain injectiontechniques and Finite Elements with Embedded strong discontinuities (E-FEM). In the present research, classical strain localizationand strong discontinuity approaches are considered by injecting discontinuous strain and displacement modes in the finite elementformulation without an increase of the total number of degrees of freedom. Following the Continuum Strong DiscontinuityApproach (CSDA), stress

The numerical analysis of concrete dam failure scenarios requires computational tools that candeal with the formation, propagation and localization of cracks and their effects on the overall dambehaviour. It is well known that assemblies of discrete part icles connected through simpleinteraction laws can capture the global behaviour of quasi-brittle macro-material, like concrete.In this work a particle model based on the discrete element method is used. Due to computationalrestrictions some simplifications are adopted: i) a finite element model is adopted in thefoundation and in the dam zone where an elastic behaviour is expected; ii) the adopted particlesize is higher than the maximum aggregate size of dam concrete. In order to further reducecomputational times a hybrid discrete/finite model is proposed that replaces the stiffness of thefinite elements where nonlinear behaviour is expected by a discrete particle assembly in itsinterior.The hybrid discrete/finite model is validated for several case studies. The results are comparedwith those obtained with a finite element based two scalar damage model. The results show theapplicability of particle models to the study of failure scenarios of concrete dams, including itsinitial elastic response, even when the adopted aggregate structure is much larger in size than theadopted concrete aggregate.

This paper presents the relevant results of the monitoring data analysis of the Chicamba dam(Mozambique), which confirmed the existence of an ongoing concrete swelling process in the dam

This paper presents a study on the seismic response of the 132 m high Cabril arch dam, for an earthquake measured in-situ with the installed Seismic and Structural Health Monitoring system (in operation since 2008). The measured acceleration time histories are compared with results from finite element analysis in various positions in the dam body, using the seismic accelerations recorded at the dam-rock interface as inputs. The numerical simulations are conducted using two programs: i) DamDySSA4.0, a 3D finite element program develop in LNEC for dynamic analysis of arch dams

In the last decade Portugal made a significant set of investments in new hydroelectric projects under the National Dams Program with High Hydroelectric Potential. EDP Produção SA, a company of EDP - Energias de Portugal Group, played a fundamental role in the construction of these projects, in which new dams and reservoirs of significant dimensions are integrated.According to Portuguese legislation, with relevance to the RSB-Dam Safety Regulation (Decree-Law no. 21/2018 of 28 March), the DTA-Technical Documents to Support the RSB and taking into account the seismic risk associated with the region where the dams were built, it was recommending the implementation of a set of Seismic Monitoring Systems (SMS) to characterize the seismic actions and the respective structural response, as well as the assessment of the reservoirs induced seismicity.For that, it was necessary, in the design phases, to carry out several studies to define the type of dynamic monitoring systems, especially those related to the seismic monitoring systems (SMS). In their most extensive configuration, these systems, based on triaxial accelerometers sensors, may incorporate remote stations installed along the reservoirs for studying the propagation of seismic actions. For the higher dams, and to ensure a good characterization of the dynamic behaviour, continuous dynamic monitoring system (CDMS) was also installed.This paper presents the main aspects of the legislation, refers the main studies and methodologies that were used, and the general aspects of the regional geological and tectonic framework. Also, is presented several seismic monitoring systems that were implemented by EDP, namely those related to the hydroelectric projects of Baixo Sabor, Foz Tua, Ribeiradio and Alto Ceira II dams.

This paper focuses on the experience gathered from the continuous dynamic monitoring of Cahora Bassa dam, a 170 m high arch dam in Mozambique, over the past decade. The installed Seismic and Structural Health Monitoring system was designed to continuously record acceleration time series in several locations in the dam body (crest gallery) and near the dam-rock interface, under ambient/operational vibrations and during seismic events, using uniaxial and triaxial accelerometers. The system was complemented with the development of software for automatic modal identification and automatic detection of seismic vibrations. The numerical simulations are carried out using a 3D finite element program, based on a solid-fluid coupled formulation to simulate the dam-reservoir-foundation system, considering dam-water dynamic interaction and propagation of pressure waves throughout the reservoir. The main experimental outputs are presented and compared with results from 3D finite element analysis, including the evolution of identified natural frequencies over time, vibration mode shapes for specific water levels, and the dynamic response in accelerations under seismic ground motion.

Neste trabalho efetuam-se estudos de simulação numérica da resposta sísmica de uma grande barragem abóbada, considerando uma dada lei de amortecimento de Rayleigh com vista a analisar a influência da cota da albufeira. A modelação do sistema barragem-fundação-albufeira é efetuada com um modelo coupled, baseado numa formulação em deslocamentos e pressões, que permite simular a interação dinâmica barragem-albufeira considerando a propagação de ondas de pressão na albufeira. A discretização do sistema coupled é efetuada utilizando elementos finitos 3D com 20 nós. A resposta sísmica é calculada por meio de integração direta no domínio do tempo com base no método de Newmark. São apresentados os resultados da análise sísmica de uma barragem com 290 m de altura, utilizando acelerogramas sísmicos em três direções, com aceleração de pico máxima de 0.3g na direção montante-jusante. Nomeadamente, analisam-se os campos de deslocamentos e de tensões no corpo da obra para diferentes cotas de água na albufeira.

A determinação da resposta dinâmica das obras e o acompanhamento da evolução do seu comportamento durante as várias fases da vida é muito importante, estando inserido nas atividades do controle de segurança estrutural. A realização de ensaios de vibração forçada em barragens de betão para a determinação do comportamento dinâmico continua a ser uma das técnicas mais fiáveis nesta área. Nesta comunicação descreve-se a metodologia de ensaio, e apresentam-se os resultados relativos a um caso de estudo, referente à caraterização do comportamento dinâmico da barragem do Baixo Sabor. Foi desenvolvido um modelo numérico, com representação do sistema barragem-albufeira-fundação, para apoio na preparação do ensaio e interpretação dos resultados experimentais.

Os trabalhos de escavação para a implantação de grandes obras, (barragens, centrais subterrâneas, tuneis, etc.) utilizam frequentemente metodologias de desmonte da rocha com recurso a explosivos. Esta técnica sendo rápida e eficientemente produtiva, obriga ao controle da propagação de vibrações no meio circundante com ênfase ao parque edificado e respetivas infraestruturas.Recentemente foram efetuadas obras de aumento da capacidade de descarga de uma barragem de betão, nas quais, foi necessário efetuar desmonte de rocha com o recurso a explosivos nas imediações da barragem existente.Estes pressupostos impulsionaram ao desenvolvido de um modelo numérico híbrido descontínuo de elementos discretos e elementos finitos recorrendo ao 3DEC, representando os blocos da abóbada, as juntas de contração e o maciço de fundação. O objetivo deste modelo é estudar o efeito das vibrações provocadas pelas explosões no comportamento da barragem de betão e respetiva fundação, avaliando a sua segurança estrutural. A correta modelação do comportamento da fundação é fundamental para uma avaliação estrutural adequada.No presente trabalho apresentam-se os resultados do modelo numérico comparando com as medições de velocidades efetuadas em vários pontos da fundação e da estrutura no decorrer das obras, sendo posteriormente analisado os efeitos na barragem. O presente trabalho, deu início ao desenvolvimento de um modelo numérico capaz de representar a resposta da estrutura às vibrações, minimizando a subjetividade da classificação do seu grau de resistência.A elaboração deste modelo numérico permitiu desenvolver novas abordagens para a simulação das explosões, da propagação ao longo do maciço e respetivos efeitos na estrutura. Estas abordagens, devidamente adaptadas, são passiveis de serem implementadas em estudos futuros.

. The nowadays-available dynamic monitoring equipment integrating very sensitive low noise sensors creates an opportunity to implement continuously operating dynamic monitoring systems in dams and validate the suitability of these systems to monitor such massive structures with the goal of detecting damage. The detection of abnormal structural behaviour, that may indicate the occurrence of damage, can be based on control charts and is associated with shifts in the modal parameters values that are not explained by other physical phenomena but a change in the structure

In this paper the seismic response of a large arch dam (290 m high), located in a high seismicity region, is analysed. The goal is to study the influence of the reservoir water level in the dam

Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.

N/A

This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.

N/A

Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.

This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.

Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto MEBAD do P2I/LNEC 2013-2020, no período 2016-2023. Os resultados da atividade são analisados e avaliados, em face dos objetivos previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

In this work we present the version 1.0 of the GDams2D 1.0 program developed for 2D analysis of gravity dams using the finite element method. This initial version of the program is prepared to analyze the structural behavior of gravity dams for static loads, considering linear-elastic behavior, and using Lagrange finite elements of 4 sides, with 9 nodal points. The GDams2D 1.0 program, developed in MATLAB, includes a module for automatic generation of meshes with a great level of refinement (generated from coarse meshes of quadrilaterals, with 4 nodal points at the vertices) and is designed for easy adaptation to non-linear analyzes, using stress-transfer modules such as those recently developed for the DamSlide3D and DamDamage3D programs. After a brief reference to the fundamentals of solid mechanics and to the simplified hypotheses of plane elasticity, the Fundamentals of the Finite Element Method (FEM) are presented, referring in particular the formulation of the four-node, linear and isoparametric, finite element (FE4nos), with two translation d.o.f per node, and the quadrangular FEs of 9 nodes (FE9nos) used in GDams2D 1.0. Based on some examples of application to simple 2D structures whose response is knownanalytically, the advantages of FEs are emphasized in relation to FE4nos and the verification and operability of GDams2D 1.0 is made using various discretizations. Finally, the case of a gravity dam (25 m high) is presented. The dam

The main objective of this work is the development and presentation of a three-dimensional finite element program, DamSlide3D, to study the behavior of gravity dams for scenarios of sliding through the dam-foundation interface. The DamSlide3D, developed using MATLAB, includes cube-type finite elements with 20 nodal points ("serendipity") and finite interface elements with 16 nodal points (joint elements). Initially, we present the fundamental equations of Solid Mechanics, referring to the main simplified hypotheses considered in the computationally implemented formulation, which is presented mathematically as a problem of boundary values using a displacement formulation. For the structure body and for the foundation, the hypothesis of isotropic materials with linear elastic behavior is assumed and for the interfaces the hypothesis of non-linear behavior is considered using the Mohr- Coulomb criterion. The DamSlide3D input data is provided in an excel file and includes structure geometry data, material properties, support conditions and load parameters. As output, the program graphically displays the stress field (principal stresses) and the displacement field (deformed structure). The program was verified throughout three numerical tests with known theoretical solutions. In these tests a simple structure was used, composed by a column discretized in 3DFE. At the contact surface between the column and the base (horizontal surface) it was considered an interface discretized using joint finite elements. A plane surface that crosses the column with a given slope is also considered, discretized using the same type of joint finite elements. In the first test, the field of elastic stresses at the base, due to self-weight (SW) and hydrostatic pressure (HP), was compared with the theoretical results. In the second test the nonlinear column response was studied for different values of thefriction angle at the inclined interface (in this test the structure is only submitted to SW). In the third test, for the main SW + HP loads, the stability of the column is studied for a variation of the friction angle, and for a variation of the water level. In these three numerical tests the results were always consistent with the theoretical solutions. Finally, as an example of application, a gravity dam structural behavior was analyzed considering the non-linear behavior in the dam-foundation interface. The dam was subjected to self-weight and hydrostatic pressure. A parametric study was developed in order to study the dam stability for differentvalues of water level and friction angle.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto CoMatFail até ao final de 2017. É feita a apreciação da atividade desenvolvida, nomeadamente quanto ao grau de cumprimento do plano de trabalhos, bem como dos objetivos específicos e dos indicadores de desempenho propostos na ficha de projeto. São ainda referidas as aplicações dos resultados da investigação em trabalhos contratados ao LNEC e as candidaturas a financiamento externo desenvolvidas no âmbito do projeto. Inclui-se em anexo a ficha do projeto atualizada, que contempla a revisão do plano de trabalhos.

Neste relatório apresenta-se de forma sucinta a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposta uma revisão do plano de atividades para os próximos três anos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposto um prolongamento do projeto até ao final de 2018.

This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venant’s expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.

This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.

O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).

Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.

Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.

In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.