Publications

The out-of-plane flexural bending capacity of masonry is a fundamental property for understanding the behavior of masonry structures. This study investigates the behavior of unreinforced masonry wallettes subjected to combined compression-flexural loading using the discrete element method (DEM), and provides a novel framework to estimate the masonry strength. A simplified micro-modeling strategy is utilized to analyze a masonry wallette, including the variation of the mechanical properties in masonry units and joints. Stochastic DEM analyses are performed to simulate brickwork assemblages, assuming a strong unit-weak joint material model typical of most masonry buildings, including historical ones. Once the proposed computational approach is validated against the experimental findings, the effect of spatial and non-spatial variation of mechanical properties is explored. Two failure types are identified: joint failure and brick failure. For each failure mechanism, the variability of the response and the effects of the modeling parameters on the load-carrying capacity is quantified. Afterward, Lasso regression is employed to determine predictive equations in terms of the material properties and vertical pressure on the wallette. The results show that the most important parameters changing the response are the joint tensile strength and the amount of vertical stress for joint failure, whereas the unit tensile strength dominates the response for brick failure. Overall, this research proposes a novel framework adopting validated advanced computational models that feed on simple test results to generate data that is further utilized for training response prediction models for complex structures.

Discrete element models are being increasingly applied to model rock failure processes.Bonded-particle models, based on circular or spherical particle systems, have been successfully usedfor two decades. More recently, bonded-block models, using polygonal or polyhedral elements, have proven to be a powerful alternative. This paper describes the basis of the application of these models in the numerical simulation of failure in rock materials. The critical governing parameters are identified, and their influence is discussed. The model calibration procedure based on the analysis of laboratory tests is discussed. An application example of an underground excavation problem is presented using a simple bonded-block model employing rigid blocks and a bilinear softening contact model. The results show the capability of this approach to reproduce observed failure modes involving block fractures.

Masonry arches are a fundamental component of historical structures. The assessment of the vulnerability ofthese heritage constructions to seismic loading requires reliable and efficient numerical models. Discrete element models are an alternative to finite element models, being particularly effective in modelling collapse mechanisms created by shearing and separation of the units along the joints. Discrete element codes typically rely on explicit methods of integration of the equations of motion for dynamic analysis, which may require large run times when the recommended stiffness-proportional component of Rayleigh damping is applied. A novel approach is proposed using an alternative damping model, Maxwell damping, which involves placing multiple spring-dashpot elements in the joints, in parallel with the standard stiffness springs. This damping model is tested in the dynamic analysis of masonry arches, under pulse and earthquake loading. The results obtained in this early investigation show a good performance in the simulation of collapse under dynamic loads, in general agreement with the analyses conducted with classical stiffness-proportional damping, but reducing significantly the computational effort.

Rigid particle models based on the discrete element method (DEM) have been adopted to model creep, fracture, and the viscoelastic behaviour of asphalt mixtures considering an irregular micro-structure and particle contacts. Within a DEM framework, the Burgers contact model, which is known to have a narrow frequency and temperature range, is usually adopted to model viscoelastic properties. In this study, a new explicit three-dimensional generalised Kelvin (GK) contact model formulation for the DEM model is proposed for asphalt materials. The model is implemented following two different methodologies (GK and GK). The models are validated in uniaxial tension-compression sinusoidal tests for predicting the dynamic modulus () and phase angle (

Encapsulated rejuvenators embedded in asphalt mixtures are a promising technology toextend the service life of asphalt pavements. However, their effects on the asphalt mixture

N/A

This paper describes the study of the metrological quality of the excitation force inthe context of force vibration test of concrete dams. For this purpose, a measurementuncertainty evaluation was performed, based on available probabilistic information about theinput quantities

A conjugação entre os modelos numéricos e os resultados observadosdo comportamento das obras é uma ferramenta fundamentalno apoio ao controle de segurança de grandes obras. A barragemdo Baixo Sabor possui um sistema de monitorização dinâmicaem continuo, e foram realizados dois ensaios de vibração forçadapara duas cotas de albufeira. Neste contexto foram desenvolvidosmodelos numéricos da barragem do Baixo Sabor incorporando oconjunto barragem-fundação-albufeira. Neste artigo, apresentamseos resultados dos modelos numéricos desenvolvidos para váriosníveis da albufeira comparando com os resultados experimentais.

The structural rehabilitation of historic/traditional rubble masonry wall constructionsrequires consolidation and retrofitting solutions to be employed in order to withstand dynamic loads,high vertical loads, and differential settlements. One of these strengthening techniques is basedon the use of steel bar connectors perpendicular to the wall, considered individually or integratedinto more complex strengthening techniques. The aim of this study is to evaluate numerically thestrengthening effect of transverse steel connectors on rubble masonry walls. With this purpose, a 2Dparticle-reinforced model (2D-PMR) was devised and applied to model uniaxial compression tests.The results presented show that predictions calculated using the proposed 2D-PMR model are veryclose to known experimental results, particularly in the corresponding failure modes, the increase ofthe maximum uniaxial compression value, and ductility. Parametric studies are also conducted byvarying the diameter of the steel bars and the level of strengthening to assess the influence of thebar-bond effect and lateral plates. The presented parametric numerical studies show that (i) a two-level strengthening solution guarantees a similar response to the three-level strengthening solutionadopted in the experiments; (ii) it is not relevant to apply a grout injection during the applicationprocess of the steel connectors if lateral plates are adopted; and (iii) the 2D-PMR model can be usedin the definition of the steel bar diameter and properties; as shown, a smaller (8 mm) bar diameterpredicts a similar strengthening effect to the (12 mm) bar size adopted in the experiments. Given theperformance of the proposed 2D-PMR model, further work is underway that will allow the 2D-PMRmodel to numerically assess other reinforcement techniques, namely, reinforced micro-concrete layersand textile reinforced mortar.

he current first generation of Eurocodes is a suite of ten Euro-pean standards for the design of buildings and civil engineeringworks, whose implementation started in 2010. EN 1990 sets thebasis of structural design, with the other Eurocodes dealingwith different materials and specific aspects of design. Geo-technical aspects of design are covered by EN 1997

The integration of healing capsules into asphalt mixtures has demonstrated promising advancements in their intrinsic self-healing properties. However, the efficacy of this technology still requires further investigation. Rigid particle models, utilizing the discrete element method (DEM), have been adopted to simulate the creep, fracture, and viscoelastic behavior of asphalt mixtures, accounting for their irregular microstructure and particle contacts. This study utilizes the previously developed VirtualPM3DLab, a three-dimensional DEM framework, to numerically assess the impact of rejuvenator-modified mastic particles on the stiffness properties of post-healed asphalt mixtures where the asphalt mixture has undergone healing. Simulations consider different capsule proportions (0.30, 0.75, and 1.20 wt%) incorporated in the specimens. Numerical results reveal that the encapsulated rejuvenator reduces the stiffness modulus of asphalt mixtures, with this impact becoming more pronounced as the capsule amount increases due to the additional rejuvenator representation in the specimen. In addition, the phase angle remains unaffected across all numerical scenarios, suggesting that the viscoelastic behavior of asphalt mixtures is not significantly impacted and indicating the suitability of capsules for pavement applications. The findings also suggest that the percentage of these healing elements can slightly surpass the traditional amounts commonly used in laboratory settings.

This paper presents an updating of the analysis and interpretation ofthe structural behavior of Covão do Meio dam (in Portugal) which concrete isaffected by an ongoing swelling process.The simulation of dam

Micromechanical modelling through the Discrete Element Method (DEM) is adopted for the study of bituminous materials given its capability to replicate complex microstructures behaviour. Typically, DEM models of bituminous materials consist of an assembly of randomly distributed spherical rigid particles which interact using elastic and/or simple viscoelastic contact models, and individual aggregates are represented by single particles. However, recent years have witnessed a notable surge in research efforts aimed at incorporating true particle morphologies into numerical models.In the context of this research, an existing 3D DEM model for bituminous materials has been refined with the representation of mineral aggregates with realistic particle shapes. To achieve this, a digital library of aggregate shapes was constructed from X-ray computed tomography (CT) scans. An adaptive image-processing technique was employed to isolate the aggregates in the CT images, and the Delaunay method was used to create a 3D surface model of the aggregates. Several virtual aggregates with varying sizes were selected from this library to mirror the gradation of coarse aggregates in the 3D DEM asphalt model. Each virtual aggregate was discretized using smaller spherical particles, with its deformability given by its inner particle contacts.To evaluate the effectiveness of this enhanced approach, numerical assemblies featuring realistic particle shapes were subjected to a cyclic loading protocol. Overall, realistic particles shapes increased the stiffness modulus and decreased the phase angle of numerical specimens, and the effect was greater with a finer discretization of aggregates. The outcomes clearly demonstrate the importance of this numerical improvement to accurately simulate the bituminous mixture behaviour.

A avaliação estrutural das paredes de alvenaria de pedra tradicional é uma tarefa complexa devido à heterogeneidade e incerteza nas propriedades dos materiais constituintes, argamassa e pedra, e à variabilidade do posicionamento e geometria destes elementos na alvenaria. Nesta comunicação, modelos experimentais de alvenaria de pedra (muretes), construídos de acordo com técnicas tradicionais portuguesas, ensaiados experimentalmente sob condições de carregamento em compressão-corte, são avaliados numericamente, adotando uma abordagem de micro-modelação através de um modelo de partículas 2D (2D-MP). Estudos anteriores demonstram que os modelos 2D-MP conseguem prever o comportamento de estruturas de alvenaria antiga, nomeadamente a propagação de fendas, os modos de rotura final, a resistência máxima ao corte e a ductilidade da parede observados experimentalmente em compressão uniaxial e compressão-corte. Neste trabalho apresentam-se os estudos numéricos desenvolvidos que permitem avaliar a influência do nível de pré-compressão na resposta monotónica em compressão-corte e o desempenho do modelo 2D-MP na reprodução de ensaios cíclicos.

N/A

Stone masonry walls are the main structural elements of many historic buildings. Their restoration and preservation are a major concern given the increasing interest in the rehabilitation of built historical heritage and the implementation of preventive measures to mitigate seismic risk. The accurate structural assessment of the existing rubble stone masonry is a very complex and difficult task, due its composite and complex nature. The heterogeneity and uncertainty in material properties of its constituents, mortar and stone, the variability of the stone units positioning and geometry, among others, make its experimental characterization and accurate numerical modeling still nowadays a challenging task. In this context, the research presented aims to contribute to a better understanding of the in-plane shear behaviour of unreinforced two leaf rubble stone masonry walls, typical stone masonry of ancient buildings that are representative in Portugal.Rubble stone masonry specimens, built with traditional Portuguese construction techniques, tested experimentally under monotonic compression-shear loading conditions are here numerically evaluated, adopting a micro-modelling approach using a 2D particle model (2D-PM). In the 2D-PM model the stone and mortar elements are represented as particle assemblies that interact with each other, thus capable of representing their inherent physical and material heterogeneity. The numerical model is generated through a mapping process of the stone units and mortar joints. The experimental campaign conducted on rubble stone masonry wall specimens allowed to collect the data necessary for the calibration of the PM model parameters, namely the stone-stone and mortar-mortar elastic and strength contact properties. The validation of the 2D-PM models of the rubble stone masonry specimens under compression and combined compression-shear loading conditions is performed using the Parmac2D software. The presented results show that 2D-PM models can predict the crack propagation, the final failure modes, the maximum shear strength, and the wall ductility observed experimentally. Parametric studies are also presented that allow a better agreement between the numerical predictions and the experimental response showing the relevance of the stone-mortar interface strength properties in the overall macroscopic behaviour.

N/A

N/A

In this work three constitutive contact models that include softening are adopted for particle model fracture studies in both rock and concrete. For a single local contact, the constitutive contact model performance is initially compared in tensile, pure shear and shear tests under constant axial. Additionally, compression, direct tensile, and confined triaxial tests of quasi-britlle material discretized with spherical particles are presented and the predicted macroscopic response is compared. For a single local contact, the three contact models predict a similar behaviour. As shown, it is possible to calibrate each contact model to reproduce complex macroscopic behaviour observed in rock and concrete, but each contact model requires different contact properties or particle generation procedures.

Asphalt mixture faces damage due to vehicle speed, repeated loads, and ultravioletradiation over time, regardless of being a self-healing material. Induced healing mechanismsare necessary to promote autonomous pavement recovery due to adverse in-service conditions,and the capsule-asphalt mixture system incorporating low-viscosity oils (rejuvenators) hasshown to be a possible solution in laboratory tests. This study aims to numerically investigatethe effect of rejuvenator-modified mastic (activated capsules) on the stiffness properties ofasphalt mixtures within the discrete element method. A three-dimensional model previouslyvalidated for rejuvenator-modified mastics with different rejuvenator-to-bitumen ratios (0, 2.5,and 10 wt%) is adopted. A generalised Kelvin contact model represents the time-dependentcontacts, and its contact parameters define the rejuvenator amount in the mastic phase. Theanalysis assesses the impact of the modified mastic amount and the rejuvenator-to-bitumenratio. Results show that the increasing modified mastic content progressively reduces themixture dynamic modulus. When the total mastic phase has rejuvenator-modified properties,the mixture stiffness modulus significantly reduces, and the phase angle performs differentlyfrom the expected (decrease with frequency) at a 10% rejuvenator-to-bitumen ratio due to theexcessively softened state, possibly compromising the pavement mechanical performance. Fora 0.30 wt% modified mastic ratio case adopting a local effect, the embedded elements do notsignificantly influence the mixture rheological properties, especially the stiffness modulus,which may be insufficient for self-healing purposes. Nevertheless, the negligible impact on thephase angle highlights the potential of the rejuvenator-modified asphalt mixture across differenttraffic and temperature conditions.

Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.

N/A

This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.

N/A

Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.

This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.

Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.

A brief description of the phenomena and problems associated with underground structures in hydraulic projects is presented, namely in what concerns the powerhouses, surge chambers and pressure tunnels and shafts. An analysis of the calculation methodologies followed in the structural design of this works is presented, as well as of the numerical models usually adopted, namely finite and boundary element models. Finally, some applications of computational mechanics are presented. First, a parameter study for underground powerhouses, with special emphasis in the definition of shapes, existence of several caverns,and in the tridimensional equilibria is described. Afterwards, examples of application to some hydraulic projects are illustrated: a large underground powerhouse in Mozambique, the Alto Lindoso hydroelectric power scheme in construction in the north of Portugal, and the Castelo do Bode tunnel, in operation, integrated in the water supply system to Lisbon.

O presente trabalho aborda a origem do estado de tensão interna dos maciços rochosos e apresenta os factores que o influenciam. Apresentam-se as técnicas e a aparelhagem correntemente utiiizada na determinação do estado de tensão, bem como a interpretação dos ensaios mais comuns, dando-se maior relevo aos ensaios com macacos planos pequenos (S F J) e com o extensómetro tridimensional (S T T),efectuados correntemente pelo LNEC.

Descreve-se sucintamente uma técnica para amostragem linear de descontinuidades em faces expostas de maciços rochosos e referem-se métodos para tratamento dos dados de campo com vista à definição defamílias de descontinuidades e caracterização de uma forma estatística da sua orientação, espaçamento e extensão. Apresentam-se os resultados obtidos para o caso de uma galeria subterrânea no aproveitamentohidroeléctrico do Alto Lindoso. Para as famílias de descontinuidade identificadas apresenta-se um estudo dos blocos tetraédricos que se poderão formar nas diferentes faces de rocha e analisam-se as suas condições de estabilidade.

N/A

Apresentam-se, neste relatório, modelos numéricos baseados no método dos elementos da fronteira, desenvolvidos no LNEC para análise de estruturas subterrâneas. Tecem-se algumas considerações sobre o método dos elementos de fronteira, descrevem-se os modelos desenvolvidos para equilíbrios planos e tridimensionais e apresentam-se alguns exemplos de aplicação.

N/A

N/A

N/A

This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venant’s expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.

This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.

O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).

Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.

Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.

In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.