Publications

In Portugal, emergency situations caused by sea waves are common, and usually have serious consequences for the economy and society. It is thus crucial to implement an early warning system to forecast the occurrence of these situations in relation to wave overtopping and flooding events in coastal/port areas. The European Framework Directive 2007/60/EC of 23 October 2007 recommended the development of risk maps and flood risk management plans, including the establishment of systems for forecasting and early warning. The national and local authorities need to implement short-term/emergency measures to prevent the loss of lives and reduce economic and environmental damage.

Nesta comunicação, descrevem-se os ensaios em modelo físico realizados com o objetivo de caracterizar o campo de ondas em torno de um navio livre, quando sujeito a condições de agitação incidente regular e irregular. Estes dados são especialmente importantes para a validação de modelos numéricos de caracterização da resposta de navios à ação da agitação incidente. Assim, para cada condição de agitação incidente, efetuaram-se medições da elevação da superfície livre e das componentes da velocidade em diversos pontos em redor do navio. Apresentam-se as seguintes análises dos dados experimentais: análise temporal e espetral (espetro de energia e wavelets) dos valores de elevação da superfície livre e análise temporal da velocidade das partículas, a meio da coluna de água. A análise temporal e espetral de cada série de medições obtida permitem a caracterização da agitação nos pontos em redor do navio, em termos de alturas, períodos e velocidade. Avalia-se também a influência do navio nas características da agitação.

Este artigo apresenta os resultados da aplicação do modelo numérico Simulating Waves Nearshore SWAN) com análises comparativas das medidas obtidas a partir dos resultados de modelagem e de edições durante as campanhas de campo em 2010 e 2012 no Litoral Setentrional do Rio Grande do Norte (NE do Brasil). O objetivo principal do presente estudo foi aplicar e validar o modelo numérico SWAN na determinação do clima de ondas, avaliar seus pontos fortes e limitações para a região de interesse. Os dados de campo realizados em dois pontos próximo da costa em profundidades de 3 m (PT_1) e 6 m (PT_2) por meio do uso de dois adcp: AWAC e AQUADOPP. Os dados adquiridos com estes equipamentos foram processados e permitiram a realização de análises espectrais de altura signifi cativa, HS (m), período médio, Tmed (s), e direção média, DIR (º). Para a implementação do modelo SWAN foram empregados para as condições de contorno os dados de agitação a partir do modelo de 3ª geração de escala oceânica Wavewatch III. Para o refi namento e aplicabilidade do modelo, foram introduzidos dados de ventos e maré locais, corrigidos com base no Manual de Engenharia Costeira (CEM), permitindo assim, melhor ajuste dos resultados da modelagem. O domínio de cálculo foi referenciado para as imensões da carta náutica 720, com três malhas regulares de diferentes dimensões e resolução: externa, intermediária e interna, sendo esta última, utilizada para fornecer os parâmetros de propagação da onda ao longo da costa. As confi gurações usadas para o SWAN foram as padrões em modo estacionário, com as formulações KOMEN, a dissipação devido à rebentação induzida pelo fundo com atrito de fundo usando a formulação JONSWAP com coefi ciente de atrito

Wave energy extraction in coastal regions may be an excellent alternative due to the increase in global demand for renewable energy. The viability study of this extraction depends on the evaluation of the wave energy potential that is higher in regions located in high latitudes. Therefore, this study shows evaluation and characterization of wave energy in the south of Brazil. Numerical simulations were carried out by the Mike 21 SW spectral model which was calibrated and validated in the region measurement campaigns. Annual, seasonal and monthly means and the temporal variability of the wave energy potential in a 10-year wave hindcast were analyzed offshore and nearshore. Annual mean fluxes in three points nearshore had similar values; the highest one was 6.7 kW/m, while the wave energy flux offshore was 22.3 kW/m. The refraction and the bottom friction dissipation were responsible for the wave attenuation from offshore to nearshore and, consequently, for the decrease in wave energy. The annual, seasonal and monthly variabilities of wave energy fluxes were moderate offshore and high nearshore. A directional analysis showed that the dominant wave directions were S and NE offshore whereas they were SSE and E nearshore.

No presente trabalho descreve-se a aplicação de uma metodologia para avaliação das consequências do galgamento no porto de Ponta Delgada, S. Miguel, Açores, recorrendo a uma análise multicritério (Processo de Análise Hierárquica, AHP) do impacto da ocorrência de galgamentos superiores aos limites admissíveis. Esta metodologia permite obter resultados baseados numa análise espacial dos indicadores que caraterizam a zona portuária em estudo, no que diz respeito à sua importância relativa.

This paper describes the analysis of the propagation of regular and irregular waves in a flume by using Fluent® model, which is based on the Navier-Stokes (NS) equations and employs the finite volume method and the Volume of Fluid (VoF) technique to deal with two-phase flows (air and water). At the end of the flume, a numerical beach is used to suppress wave reflections. The methodology consists of adding a damping sink term to the momentum equation. In this study, this term is calibrated for three cases of regular incident waves (H = 1 m, T = 5, 7.5, and 12 s) by varying the linear and quadratic damping coefficients of the formulation. In general, while lower values of damping coefficients cause residuals on the free surface elevation due to wave interactions with the outlet boundary, reflection occurs on the numerical beach when higher values are used. A range of optimal damping coefficients are found considering one of them null. In one of these cases, temporal series of free surface elevation are compared with theoretical ones and very good agreement is reached. Afterwards, an irregular wave propagation, characterized by a JONSWAP spectrum, is investigated. Several gauges along the flume are evaluated and good agreement between the spectrum obtained numerically and the ones imposed at beginning of the flume is verified. This study shows the capacity of NS models, such as Fluent®, to simulate adequately regular and irregular wave propagations in a flume with numerical beach to avoid reflections.

Scale-model tests are usually required to evaluate the hydraulic and structural behavior of proposed rubble-mound breakwater designs. In order to speed up and ease the armor layer damage assessment, we developed a technique based on stereo photogrammetry. A key feature of this technique is its ability to compensate for the refraction in the air-water interface, thus producing a survey of the envelope of the armor layer without the need to empty the wave flume or wave basin where the scale model tests are carried out. This article describes this technique and the tests made to establish confidence in it and in the damage evaluation on a breakwater scale model. Results led to an error estimation of only fractions of a centimeter.

A set of physical model tests was run in to characterize the ship

Nowadays, renewable energy is a topic widely discussed in scientific community. Specifically wave energy attracts attention because it has a high energy potential distributed throughout the planet. Oscillating Water Column (OWC) wave energy converter is one of the most studied devices that have promising perspectives to be installed commercially. This study aims investigating the influence of chamber sizes and turbine characteristics dimensions of an OWC device located at the southern Brazilian coast is carried out. Numerical simulations for incident waves with period T = 7 s and 10 s and height H = 1.5 m, by using the FLUENT® model, based on the finite volume method (VFM) are carried out. Efficiencies for different chamber sizes and Wells turbine characteristic relations (kt) in each incident wave are determined. The highest efficiencies were obtained by a chamber with 5 x 5 m and kt = 530 Pa.s/m³ in the case of an incident wave with T = 7s (52%), and 30 x 30 m and kt = 15 Pa.s/m³ at T = 10s (65%).

Port terminals downtimes lead to large economic losses and largely affect the port

This paper describes the physical model, experimental setup and tests performed to study the motions and forces of a ship moored to the pier A at the Leixões oil terminal, following the breakwater

HIDRALERTA is a forecast, early warning and risk assessment system for port and coastal areas that uses measurements and estimates of sea-waves and water levels to evaluate overtopping/flooding events. The calculation of the mean overtopping discharge over a maritime structure is performed through artificial neural network-based tools and/or empirical formulae. The system is developed in open source software, mainly using the Python language. This paper presents the application of HIDRALERTA system to reproduce the hurricane Lorenzo conditions and impacts at Lajes das Flores port on October 2nd 2019, the most affected port in Azores. This hurricane was regarded as the strongest storm to hit Azores in 20 years. The system predicted the expected results for the hurricane wave characteristics, as well as overtopping discharge volumes. Further validation still need to be improved with the collaboration of the local authorities and the use of historical data.

Numerical models are useful tools to predict the effects of storms in coastal areas. The objective of this work was to simulate the effects of storms in São Pedro de Moel beach by using XBeach. The nearshore sea state was obtained by propagating offshore conditions using the SWAN model. The XBeach model was divided into two setups to analyse overtopping events and coastal evolution. Sensibility tests, calibration, and validation, using information from different storms, were performed for the different setups. The results from the overtopping simulation were compared against results from an empirical formula. The comparison showed lower values obtained with the empirical formula. The coastal evolution run point out to the necessity of having better field data before and after storms to improve the model setting and accuracy.

The assessment of damage evolution in scale model tests of rubble-mound breakwaters can be achieved by comparing eroded depths and volumes between consecutive surveys. This paper focuses on damage evolution of a model of a rubble-mound breakwater and on the novelty of the non-intrusive survey methodologies such as laser scanning and Time of Flight (ToF) techniques, based on point clouds, enabling the extraction of profiles and the calculation of eroded depths and eroded volumes. The final objective of this work is to evaluate the applicability of the estimation the number of displaced armour units, using a non-dimensional damage parameter based on the calculated eroded volume.The paper will also describe the experiments conducted under the RODBreak, a project sponsored by the HYDRALAB+ Transnational Access Program, in which a stretch of a rubble-mound breakwater was built at the wave-current basin of the Leibniz University Hannover (LUH) to assess the structure behavior. Four scan surveys were conducted using a Faro Focus 3D laser scan, as well as a ToF sensor. Those surveys were carried out before and after two test series, in order to evaluate the eroded volume and profile evolution.

Neste trabalho é efetuada a validação do protótipo To-SEAlert para o porto da Ericeira. Para a validação dos resultados do modelo SWAN foram utilizados os dados de duas boias situadas ao largo da Nazaré e para a validação das previsões do sistema de cálculo do grau de risco foram simuladas as depressões Elsa e Fabien (ocorridas em dezembro de 2019) e que foram responsáveis por fortes danos na cabeça do molhe do porto da Ericeira. Verificou-se uma boa concordância entre os dados das boias e os resultados do modelo SWAN, tendo no entanto o modelo reproduzido melhor a direção média e a altura significativa do que o período de pico. Relativamente aos valores de galgamento, os resultados obtidos na simulação das depressões Elsa e Fabien estiveram em concordância com os valores referidos na literatura como causadores de danos nas estruturas.

This work aims to determine the exploitable wave energy resource at six potential sites, located in the Azores, Madeira and Sines breakwater city harbours. For that purpose, the thirdgeneration wave model SWAN is used to estimate the sea-wave conditions over the last 40 years. Boundary conditions of the sea states and wind fields are provided by the climate reanalysis datasets (ERA5). Using those results as inputs to the SWAN model, the sea-states were propagated shoreward, in order to estimate and analyse the wave climate conditions in the regions of interest. By combining the average energy flux per unit-length of wave front and the probability of occurrence of each sea state, the average exploitable annual energy per unit length of wave crest can be computed. The variability of this energy flux is described, since it is of fundamental importance for the efficiency of the Wave Energy Converters (WEC).

Former investigations on wave run-up and overtopping of (impermeable and permeable) coastal structures aimed at quantifying the influence of oblique waves on mean overtopping discharge, water layer thickness and velocities by developing empirical formulas of a reduction factor for wave obliquity,

In 2017, the RODBreak experiment was conducted. The experiment aimed at characterizing wave run-up, overtopping and damage in rubble-mound breakwaters. The reason for these experiments was the huge impact that climate can have on maritime structures, particularly in rubble mound breakwaters. In fact, the forecast sea level rise associated with more frequent and severe storms will have consequences either on the increase of wave runup, wave overtopping or on damage on existent structures since they were not design for those extreme values. However, for those climate change scenarios, little is known about the actual failure probability of such structures.Within this framework, a stretch of a rubble-mound breakwater was built in a wave basin. Under extreme wave conditions, with different incident wave angles (from 40° to 90°), a total of 49 tests were performed. Each test had different testing parameters, such as significant wave height (Hs), peak period (Tp) and wave direction. Also, for each test, different types of measurements were considered. Incident sea waves were measured with 3 arrays of 6 acoustic wave probes each as well as with isolated acoustic wave probes and 5 Acoustic Doppler Velocimeters (ADV

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Realização de ensaios em modelo físico reduzido 3D para a avaliação da estabilidade do quebra-mar destacado do Porto Inlgês, Maio, Cabo-Verde

N/A

Adverse sea conditions can cause emergency situations associated to wave overtopping, which endanger the safety of people and goods, with negative impacts for society, the economy and the environment. Therefore, a methodology to assess the overtopping risk in port and coastal areas is essential for a proper planning and management of these areas.The Portuguese National Laboratory for Civil Engineering (LNEC) has been developing the HIDRALERTA system, an integrated decision-support tool for port and coastal management, which focus in preventing and supporting the management of emergency situations and the long-term planning of interventions in the study areas. It enables the user to calculate the risk for various port and coastal activities, starting with the characterization of sea-waves, wind field and tide levels at the study regions.HIDRALERTA was already tested at different places in Portugal: Costa da Caparica beach, in Almada, and port of Praia da Vitória, in the Azores. However, in both cases, the evaluation of wave overtopping / flooding consequences was carried out using a quite simple approach. In fact, such consequences were assessed only at a global and qualitative level, based on information provided by the responsible authorities.This paper aims at testing a quantitative methodology to evaluate overtopping consequences: the Analytic Network Process (ANP). This methodology was proposed to solve complex decision-making problems and its objective is to calculate the priorities among decision elements which will define their final weights on the consequences. The ANP approach can produce interdependencies between criteria and compute the respective weight of each criterion. Such a network model with dependence and feedback improves the priorities derived from judgements and makes prediction more accurate. So, the ANP allows comparison among clusters of elements. Furthermore, in this methodology we take into account the impacts of alternatives on the importance of criteria, by normalizing the comparison matrix. Thus, the given alternatives can influence the ranking of criteria.Application of the ANP methodology to the case study of Praia da Vitória port is presented and a consequences level map is obtained.

Apresenta-se um novo sistema de alerta para navios amarrados em portos que se encontra em desenvolvimento no Laboratório Nacional de Engenharia Civil. O sistema SWAMS_ALERTA é um sistema de previsão e alerta baseado na avaliação do risco associado ao comportamento de navios amarrados em zonas portuárias.Os riscos associados a navios amarrados decorrem de movimentos excessivos, quer no plano horizontal, quer no plano vertical. Estes movimentos podem condicionar as atividades portuárias, nomeadamente cargas e descargas, mas em casos extremos podem levar à ocorrência de situações de emergência, tais como rotura de cabos, rotura de cabeços de amarração ou até colisões com o cais. As consequências deste tipo de situações envolvem sempre grandes prejuízos materiais e por vezes humanos.O sistema SWAMS_ALERTA utiliza as medições e previsões de agitação marítima para a determinação dos seus efeitos em termos de movimentos nos seis graus de liberdade e forças nas amarras e defensas quando o navio se encontra estacionado no cais. Para tal, o sistema recorre a uma série de modelos numéricos, interligados entre si. A comparação destes valores com valores máximos admissíveis pré-estabelecidos permite a avaliação, em tempo real, de situações de emergência e a emissão de alertas dirigidos às entidades portuárias.O sistema é constituído por 4 módulos:I

N/A

N/A

N/A

N/A

N/A