Papers
Info
Extensão do molhe norte do Porto de Leixões: modelação física de um navio amarrado no posto A
O Porto de Leixões, localizado na costa norte de Portugal, é um dos maiores do país, recebendo diariamentevários navios de grandes dimensões. Um dos principais postos de acostagem situa-se à entrada do porto e encontra-se sujeito à agitação marítima que é difratada pelo olhe principal de proteção do porto. Para avaliar dos movimentos induzidos no navio estacionado nesse posto de acostagem e as forças exercidas nas suas amarras e defensas pela agitação incidente, utilizou-se o modelo físico de Leixões, construído num dos tanques do LNEC. Neste modelo físico, encontra-se representada a envolvente do porto de Leixões, assim como a sua batimetria. O modelo do navio
Year: 2020
Number Pages:
17-28pp.
Author(s): Pinheiro, L.; Pedro, F.; Abdelwahab, H.S.; Fortes, C. J. E. M.; Santos, J. A.; Capitão, R.
: Revista Recursos Hidricos
Editor: APRH
Volume:
Volume 41, Nº 1.
Keywords: Motions measurement; Constitutive relations; Moored ship; Scale model
Info
Numerical analysis of an onshore oscillating water column wave energy converter for different wall slopes
An alternative to the energy matrix expansion, due to the increase of global electricity demand, is the renewable sea wave energy source, which has high energy potential. The Oscillating Water Column (OWC) converter is one of the most studied, although it is not yet used at commercial scale. Therefore, searching the optimal geometric configuration is fundamental to turn this device viable. This study proposes a numerical analysis of an onshore OWC for different slopes of chamber walls (from 40o to 90o) and equipped with a Wells turbine. Simulations of incompressible 2D flows are performed by means of the FLUENT® software, which is based on Reynolds-averaged Navier-Stokes (RANS) equations. The k-
Year: 2020
Number Pages:
10-22pp.
Author(s): Güths, A.K.; Teixeira, P. R. F.; Didier, E.
: Revista Interdisciplinar de Pesquisa em Engenharia
Editor: RIPE
Volume:
Volume 6 No. 2.
Keywords: Numerical simulation; Renewable energy; Wave energy; Oscillating water column
Info
Numerical analysis of the influence of air compressibility effects on an oscillating water column wave energy converter chamber
The most studied device used for extracting wave energy is the Oscillating Water Column (OWC). In general, numerical simulations of these cases by means of models based on Reynolds Averaged Navier-Stokes equations adopt the Volume of Fluid method to deal with the free surface flow which is considered incompressible in both water and air. The aim of this study is to investigate the influence of the compressibility effect on the air inside the OWC chamber by the FLUENT® numerical model. A methodology is implemented, taking into account both water and air flows incompressible, but, at every instant, a pressure condition is imposed on the top boundary of the chamber to consider the compressibility effect. This pressure condition is based on an analytical equation that considers the isentropic transformation of the air and effects of Wells and impulse turbines. Results of compressible and incompressible numerical models are compared. The amplification factor, the root mean square of air pressure inside the chamber and OWC efficiency in relation to incident wave period, wave height and turbine characteristic relation are analyzed. Results show that air compressibility effects can diminish the predicted OWC efficiency up to about 20% in both Wells and impulse turbines.
Year: 2020
Number Pages:
1183-1193pp.
Author(s): Gonçalves, R.; Teixeira, P.; Didier, E.; Torres, F.
Editor: Elsevier
Volume:
Volume 153.
Keywords: Air compressibility; Volume of fluid; Numerical simulation; Oscillating water column device; Wave energy
Info
Numerical analysis of the performance of two onshore oscillating water column wave energy converters at different chamber wall slopes
In this study, a numerical analysis of the performance of two Oscillating Water Column (OWC) wave energy converters, at different front and back wall slopes, was carried out. The first device had vertical front and back walls and the second one had its wall slopes of 40° in relation to the horizontal plane. The FLUENT® numerical model, which is based on the Reynolds-Averaged Navier-Stokes (RANS) equations, was used. The Volume of Fluid (VoF) method was employed to take into account free surface flows. The case study comprised a 10 m deep flume with an onshore OWC at its end, equipped with a Wells turbine. A 2D hydrodynamic mathematical model was employed and a 3D air pressure effect inside the OWC air-chamber was considered. Analyses of the hydrodynamics behavior, fluid-structure interaction outside (run-up/down, reflected waves) and inside the chamber (free surface elevation, sloshing) and energy distribution (pneumatic extracted energy, reflected wave energy and energy losses) were conducted. Results showed that the device with inclined walls had the best efficiency in comparison with the other one. However, the latter showed lower variation in efficiency in the wave period range than the former.
Year: 2020
Number Pages:
14p.
Author(s): Gaspar, L. A.; Teixeira, P.; Didier, E.
: Revista Ocean Engineering
Editor: Elsevier
Volume:
Volume 201.
Keywords: Volume of fluid; Finite volume method; Numerical simulation; Oscillating water column device; Wave energy
Info
Numerical analysis of the response of an onshore oscillating water column wave energy converter to random waves
The main objective of this study is to investigate differences of random incident waves from regular ones in performance of wave energy converters (WEC). A numerical analysis of an onshore oscillating water column (OWC) WEC is carried out by means of the FLUENT® software, which is based on Reynolds - Averaged Navier-Stokes equations. Analyses of the efficiency of an onshore OWC device with similar characteristics of the Pico
Year: 2020
Number Pages:
12p.
Author(s): Teixeira, P. R. F.; Didier, E.
: Revista Energy
Editor: Elsevier
Volume:
Volume 220.
Keywords: Irregular/Random waves; RANS-VoF; Wells turbine; Oscillating water column; Wave energy
Info
O papel da engenharia na proteção do território e das suas gentes
Atualmente, mais importante que assegurar a resistência de um aglomerado urbano a um eventual invasor, importa garantir a sobrevivência a catástrofes naturais das infraestruturas críticas que garantem a salubridade das condições de vida nesse aglomerado, a mobilidade dos habitantes e o abastecimento de bens essenciais. Em rigor, face ao carater aleatório destas solicitações, pretende-se que, uma vez terminadas essas solicitações extremas, eventuais estragos causados pelas mesmas não impeçam o restabelecimento, em tempo útil, das atividades normais da população. Nesta comunicação apresentam-se ferramentas e procedimentos para avaliação do risco associado a infraestruturas críticas com um viés para o controlo de cheias urbanas e de infraestruturas de transporte marítimo.
Year: 2020
Number Pages:
201-221pp.
Author(s): Santos, J. A.; Pinheiro, L.; Fortes, C. J. E. M.
: Madeira Região Resiliente. Aprender com o Passado. Série Estudos Cindínicos
Editor: RISCOS - Associação Portuguesa de Riscos, Prevenção e Segurança
Volume:
Volume 9 (2020).
Keywords: Avaliação do risco; Resiliência; Infraestruturas críticas
Info
Sines breakwater harbour: the OSOM+ monitoring program
The current program of Systematic Observation of Maritime Works (OSOM+), under development at the National Laboratory for Civil Engineering (LNEC), is essentially applied to rubble mound breakwaters. The OSOM
Year: 2020
Number Pages:
49-57pp.
Author(s): Fortes, C. J. E. M.; Capitão, R.; Lemos, R.; Neves, M. G.; Silva, L. G.; Henriques, M. J.; Martins, T.
: Italian Journal of Engineering Geology and Environment
Editor: Sapienza Università Editrice
Volume:
1 (2020).
Keywords: Drone; Visual observations; Maintenance; Monitoring; Rubble mound breakwaters
Info
The HIDRALERTA system: Application to the ports of Madalena do Pico and S. Roque do Pico, Azores
HIDRALERTA is a forecast and early warning system for coastal and port regions capable of predicting emergency situations, as well as carrying out risk assessment. The system concentrates on evaluating wave overtopping and flooding scenarios. It uses offshore sea-wave and wind forecast data, as well as tide data, as input to determine wave overtopping at specific locations. The calculation of the mean overtopping discharge over a structure is made through artificial neural network (ANN) tools and/or empirical formulae, which are able to define the spatial distribution of the flow behind the structure.The HIDRALERTA system is composed of four modules developed in Open Source Web Technology, mainly using the Python Language. The Warning System can be configured and adapted for specific scenarios. The system has been successfully tested for the Port and Bay of Praia da Vitória, Terceira Island, Azores, Portugal, and is now under development and being implemented at the ports of Madalena do Pico and S. Roque do Pico.This paper describes the work carried out to date on the system and its application to these two ports in the Pico Island, Azores.
Year: 2020
Number Pages:
10p.
Author(s): Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Pinheiro, L.; Poseiro, P.; Serrazina, V.; Mendonça, A. C.; SMITHERS, N; SANTOS, M.I.; Barateiro, J.; Azevedo, E. B.; SALVADOR, M.; Reis, F.
: Revista Aquatic Ecosystem Health & Management
Editor: Taylor & Francis
Keywords: Warning system; Flooding; Wave overtopping
Info
3-D scale model study of wave run-up, overtopping and damage in a rubble-mound breakwater subject to oblique extreme wave conditions
A set of scale-model tests carried out to enlarge the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater
Year: 2019
Number Pages:
32-41pp..
Author(s): Santos, J. A.; Pedro, F.; Coimbra, M.; Figuero, A.; Fortes, C. J. E. M.; Sande, J.; Körner, M.; Lemos, R.; Bornschein, A.; Weimper, J.; van den Bos, J.; Dost, B.; Hofland, B.; Carvalho, R.; Alvarellos
: Defect and Diffusion Forum
Editor: Trans Tech Publications Ltd, Switzerland
Volume:
Volume 396.
Keywords: Instrumentation; 3D-Wave basin; Physical modelling
Info
A numerical tool for modelling oscillating wave surge converter with nonlinear mechanical constraints
Mechanical constraints have a non-negligible influence in the motion of oscillating wave surge converter (OWSC) devices. The key novelty of this paper is a numerical simulation tool for OWSCs that does not neglect or significantly compromise mechanical constraints such as hydraulic power take-off (PTO) system, revolute joints and frictional contacts among components. The paper is aimed at presenting the key components of the numerical simulation tool and at validating it with laboratory data featuring an OWSC with mechanical constraints under regular and irregular waves. It is based on the implementation of the multibody solver of Project Chrono under the Smoothed Particle Hydrodynamics (SPH) model of DualSPHysics, where the SPH solver resolves the interaction between wave and flap and the multibody solver resolves the interaction between flap and mechanical constraints. Comparison between numerical results and experimental data show that the numerical simulation tool properly predicts the dynamics of the OWSC. Furthermore, in what concerns hydrodynamics of the near-flap flow, the computed and measured free-surface elevations and phase-averaged flow field show reasonable agreement. Once properly validated, the numerical simulation tool is then applied to study the influence of several mechanical constraints, PTO damping characteristics and flap inertia on the hydrodynamic of the OWSC. The viability of OWSC design solutions based on the developed numerical simulation tool is emphasised, in view of its performance in the test cases to which it was subjected.
Year: 2019
Number Pages:
2024-2043pp.
Author(s): Brito, M.; R. Canelas; García-Feal, O.; Domínguez, J. M.; Crespo, A. C.; Ferreira, R. L.; Neves, M. G.; Teixeira, L.
: Renewable Energy
Editor: Elsevier
Volume:
146.
Keywords: Wave-structure interaction; Wave energy; Mechanical constraints; Oscillating wave surge converter (OWSC); Smoothed particle hydrodynamics (SPH); Numerical modelling
|
Comunicação
Info
Modelação numérica: análise dos parâmetros de surfabilidade de um quebra-mar destacado multinfuncional em frente à praia da Vagueira
O presente trabalho enquadra-se no estudo de caracterização e definição de parâmetros de dimensionamento e localização de um quebra-mar destacado (QMD), em frente à Praia da Vagueira (Município de Vagos, distrito de Aveiro) que está a ser desenvolvido para a Agência Portuguesa do Ambiente, I.P.,.Pretende-se que o QMD seja multifuncional contribuindo para reduzir o risco de galgamentos costeiros no aglomerado urbano da Praia da Vagueira; promover o eventual acréscimo do areal da praia emersa em frente à defesa aderente, reforçando a defesa natural contra a erosão e inundação costeira e fomentando o seu maior usufruto pela população e segurança balnear; e ainda criar condições físicas para promover ondas de surf, potenciando a economia associada a esta atividade.Neste âmbito, e para análise das potencialidades do QMD para promover ondas de surf na zona, aplica-se o modelo não-linear de tipo Boussinesq COULWAVE na simulação da propagação de ondas na zona em estudo, para a situação antes e após a implantação do QMD. Este modelo permite reproduzir a maioria dos fenómenos intervenientes na transformação da onda em fundos de profundidade variável e na presença de correntes: dispersão de frequência, dispersão de amplitude, empolamento (linear e não-linear), difração, refração pelo fundo e devida às correntes, geração de harmónicas e dissipação de energia por rebentação da onda.Analisam-se os parâmetros de surfabilidade necessários para verificar se as condições na zona são propícias para a prática do surf, nomeadamente o número de Iribarren, ângulo de rebentação, amplificação da onda e o comprimento da linha de rebentação.
Year: 2021
Number Pages:
4p.
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Santos, J. A.
Editor: APRH
Keywords: COULWAVE; Modelação numérica; Parâmetros de surfabilidade; Vagueira; Quebra-mar destacado
Info
Porto de Peniche: ensaios em modelo físico de um trecho do quebra-mar oeste
Nesta comunicação descreve-se o conjunto de ensaios efetuados em modelo reduzido de um perfil do quebra-mar oeste do porto de Peniche. O objetivo destes ensaios é avaliar o impacto no espraiamento, no galgamento, nas pressões na superestrutura e na evolução do dano no talude do perfil, de diferentes condições de agitação marítima extremas designadamente as associadas a cenários de alteração climática.
Year: 2021
Number Pages:
3p.
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Lemos, R.; Neves, M. G.; Capitão, R.; Pinheiro, L.; Costa, C.E.B.C.; Reis, R.; Simão, J.; Soares, R. E.
Editor: CNME2020
Keywords: Peniche; Dano; Superestrutura; Galgamento; Espraiamento; Agitação marítima; Modelação física
Info
Project TO-SEALERT. First developments
The project To-SEAlert aims to develop, implement and validate a set of tools/methodologies for an early warning, forecast and alert, emergency planning and risk management WebGIS system, based on the existing HIDRALERTA system. This updated WebGIS system will help responsible authorities to monitor, prevent and/or manage overtopping and flood emergency events in coastal and port areas and to plan investments on a long-term basis. The new system includes the use of satellite and video images, numerical and physical modelling, and quantitative risk assessment techniques to enhance the reliability and efficiency of the system. It will also establish/implement/monitor emergency plans to help authorities handle these events. The test cases are Costa da Caparica and Ericeira harbour, sites with significant occurrence of wave driven overtopping and flooding with significant consequences for the infrastructures, goods, and people.This paper aims to describe the project, namely its objectives, methodology and main expected results, as well as the achievements attained so far.
Year: 2021
Number Pages:
4p.
Author(s): Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Zózimo, A. C.; Santos, J. A.; Pinheiro, L.; Lemos, R.; Capitão, R.; Fonseca, A. M.; Barateiro, J.; Serrazina, V.; Craveiro, J.; Andriolo, U.; Taborda, R.; Si
Editor: APRH
Keywords: Risk assessement; Early warning; Flooding; Overtopping; To-SEAlert
Info
Prótotipo do TO-SEALERT para o porto da Ericeira
O projeto de investigação e desenvolvimento To-SEAlert financiado pela Fundação para a Ciência e a Tecnologia e envolvendo o LNEC, a FCiências.ID, a NOVA.ID.FCT e o ISEL tem como objetivo o desenvolvimento de um sistema de previsão, alerta, planeamento de emergência e gestão de risco de galgamentos e inundações em zonas costeiras e portuárias, com base no sistema HIDRALERTA. Partindo das características da agitação marítima ao largo e utilizando modelos numéricos para a propagação e deformação da agitação marítima, o sistema HIDRALERTA estima os parâmetros relevantes da agitação marítima para a avaliação do galgamento e da inundação bem como o risco associado a esses eventos. As funcionalidades que se pretendem melhorar no âmbito do projeto To-SEAlert dizem respeito às metodologias de previsão do galgamento e da delimitação da zona inundada, bem como no apoio à resposta a situações de emergência envolvendo fenómenos de galgamento. A implementação e a validação do protótipo do To-SEAlert estão a ser efetuadas para a zona costeira da Costa da Caparica e para o porto da Ericeira.Esta comunicação apresenta o trabalho desenvolvido até à data na construção e desenvolvimento do protótipo do To-SEAlert para o porto da Ericeira.
Year: 2021
Number Pages:
4p.
Author(s): Zózimo, A. C.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Pinheiro, L.; SMITHERS, N; Serrazina, V.
Editor: APRH
Keywords: Emergência; Previsão e alerta; Galgamento; HIDRALERTA; To-SEAlert; Ericeira
Info
Run-up measurements under very oblique wave incidence
Under the scope of the HYDRALAB+ transnational access project, the so-called RODBreak was conducted in the directional wave basin at the Marienwerden facilities of the Leibniz UniversityHannover (LUH).A stretch of a rubble-mound breakwaterwas built in the wave basinwith a very gentle slope and an armour layer made of Antifer cubes, at the roundhead and adjoining trunk, and rock, at the rest of the trunk.Aset of scale-model tests wascarried out to extend the range of wave steepness values analysedin wave run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions,with incident wave angles from 40º to 90º.The present study focuses on the analysisof measured wave run-up values obtained ina physical model and on its variability with wave parameters and wave obliquity.
Year: 2021
Number Pages:
4p.
Author(s): Lemos, R.; PINA, V.; Santos, J. A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.
Editor: APRH
Keywords: RODbreak; Physical modelling; Oblique waves; Run-up; Rubble-mound breakwaters
Info
Simulation of hurricane Lorenzo at the port of Madalena do Pico, Azores, by using the HIDRALERTA system
HIDRALERTA is a forecast, early warning and risk assessment system of port and coastal areas that uses measurements/estimates of sea-waves and water levels to evaluate overtopping/flooding. The calculation of the mean overtopping discharge over a maritime structure is performed through artificial neural network-based tools and/or empirical formulae. The system is composed of four modules developed in open source Web technology, mainly using the Python language. This paper presents its application to reproduce the hurricane Lorenzo conditions and impacts at Madalena do Pico port, Azores, on October 2 2019. This hurricane was regarded as the strongest storm to hit Azores in 20 years. The application of HIDRALERTA focus mainly on the second and fourth modules: wave run-up/overtopping and warning system.
Year: 2021
Number Pages:
4p.
Author(s): SANTOS, M.I.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Pinheiro, L.; Serrazina, V.; SALVADOR, M.; Reis, F.; Azevedo, E. B.
Editor: APRH
Keywords: Madalena do Pico; Risk assessment; Overtopping; Warning system; HIDRALERTA
Info
Análise da energia de ondas infragravíticas na Baía do Espírito Santo, Brasil
A energia das ondas infragravíticas na Baía do Espírito Santo foi investigada através de duas campanhas de medição de ondas em três locais distintos. A variação da energia infragravítica ao longo do tempo foi analisada em conjunto com a evolução do espectro direcional das ondas gravíticas, com o propósito de identificar uma possível relação entre as características das ondas longas e curtas. Quatro faixas de frequência foram utilizadas para particionar o espectro direcional de energia das ondas gravíticas, para observar a evolução destas ao longo do tempo. Nos eventos energéticos de ondas gravíticas medidos ao largo da baía, o aumento da energia na faixa infragravítica só ocorreu em ambos os pontos internos, de forma similar, quando as duas faixas de períodos dominantes do espectro gravítico eram maiores que 9s. Nas outras ocasiões, a região central apresentou maiores amplificações que o ponto nas imediações do Porto de Tubarão.
Year: 2020
Number Pages:
219-222pp.
Author(s): Colaço, G.; Gallo, M.; Parente, C.; Pinheiro, L.; Fortes, C. J. E. M.; Delpuppo, D.; Freitas, T.
: Atas das 6.as Jornadas de Engenharia Hidrográfica / 1.as Jornadas Luso-Espanholas de Hidrografia
Editor: Instituto Hidrográfico
Keywords: Ondas longas; Ondas infragravíticas; Ondas gravíticas
Info
Avaliação do galgamento costeiro sem e com um quebramar destacado na frente da praia da Vagueira
Um dos aspetos a analisar na caracterização e viabilidade de um quebra-mar destacado (QMD) multifuncional em frente à praia da Vagueira é a redução de galgamentos, consequência desejável que a implementação deste tipo de estrutura marítima terá nessa zona. Para isso, foi efetuada a caracterização da agitação na zona em estudo e a avaliação dos galgamentos, para a situação atual (sem estrutura) e para várias alternativas de QMD.Com base em dados estimados ao largo, a caracterização da agitação marítima local foi obtida mediante a transferência desses dados para pontos junto à costa, utilizando, nesta ordem, os modelos de propagação de ondas marítimas SWAN e DREAMS. O período de dados ao largo considerado foi de 39 anos (1979-2018), com intervalo de 6 em 6 horas. Seguidamente, recorrendo à fórmula de Mase et al. (2013), calculou-se o caudal médio galgado na estrutura de defesa aderente aí existente, sem e com as diferentes alternativas de QMD. Finalmente, a comparação dos resultados obtidos permitiu avaliar o desempenho do QMD na redução dos galgamentos costeiros na sua zona de influência.
Year: 2020
Number Pages:
187-190pp.
Author(s): Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Pinheiro, L.
: Atas das 6.as Jornadas de Engenharia Hidrográfica / 1.as Jornadas Luso-Espanholas de Hidrografia
Editor: Instituto Hidrográfico
Keywords: QMD; Praia da Vagueira; Galgamentos; Erosão costeira; Agitação marítima
Info
Behaviour of moored ships in Azorean ports during hurricanes Lorenzo and Elsa
This work presents the results of numerical simulations of two ferry ships moored inside two ports of Pico
Year: 2020
Number Pages:
129-132pp.
Author(s): Pinheiro, L.; SANTOS, M.I.; Fortes, C. J. E. M.; Zózimo, A. C.
: Atas das 6.as Jornadas de Engenharia Hidrográfica / 1.as Jornadas Luso-Espanholas de Hidrografia
Editor: Instituto Hidrográfico
Keywords: Warning system; Overtopping; Lorenzo; Lajes das Flores; Hidralerta
Info
Comparação entre modelos numéricos na avaliação de eventos de galgamento costeiro
Este estudo recorre a ferramentas de modelação numérica, XBeach e SWASH, para a avaliação dos eventos de galgamento costeiro devido a tempestades marítimas no troço costeiro urbano da Costa da Caparica, que compreende a estrutura rígida aderente. Faz-se uma análise comparativa entre os modelos, e confronta-se com a informação de eventos documentados (tempestades Hércules e Emma). Ambos os modelos, refletem as variações entre tempestades, com maior intensidade de galgamento para a tempestade mais energética. Existem diferenças entre os modelos, ainda que pouco significativas face aos níveis de perigosidade associados (CEM, 2002; EurOtop, 2018) e ambos apresentaram resultados satisfatórios quando comparados com os relatos históricos das tempestades analisadas. O modelo XBeach requer um maior tempo de computação, contudo permite obter intervalos de confiança na previsão de galgamentos. Este estudo aponta para a viabilidade da utilização de ambos os modelos na avaliação dos eventos de galgamento costeiro na Costa da Caparica.
Year: 2020
Number Pages:
296-299pp.
Author(s): Ferreira, A. M.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Garzon, J.L.
: Atas das 6.as Jornadas de Engenharia Hidrográfica / 1.as Jornadas Luso-Espanholas de Hidrografia
Editor: Instituto Hidrográfico
Keywords: XBeach; SWASH; Tempestade marítima; Riscos costeiros
|
|
Capítulo de Livro
Info
Multi-functional artificial reefs for coastal protection
N/A
Year: 2009
Number Pages:
153-210 pp.
Author(s): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Tese de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Year: 1999
Number Pages:
159 p.
Author(s): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Year: 1998
Number Pages:
594 p.
Author(s): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Year: 1998
Number Pages:
346 p.
Author(s): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Year: 1973
Author(s): Carvalho, M. M.
Editor: ******
|
|
Relatório Científico
Info
Demonstration and technical tours plan
A major objective of TRA LISBON 2022 Conference is to boost research and innovation capacity for the transport sector, throughout a full innovation cycle, from idea to market. Having this in view, the project
Year: 2022
Author(s): Batista, F. A.; Marecos, V.; Antunes, M. L.; Macedo, A. L.; Freire, A. C.; Capitão, R.; Arsénio, E.; Maia, L.
Info
Demonstration submission and selection guidelines
The demonstration area will be one of the main focus points of TRA LISBON 2022, presenting multifunctional spaces and being prepared to receive a large number of different types of on-site demonstrations (indoor and outdoor). On-line demonstrations will also be an option, allowing for the widest possible coverage of access for all the participants.The dedicated areas will allow for interactive demonstrations of technological innovations to be carried out by and for industry partners, researchers, and other stakeholders. Demonstrations are an excellent opportunity to introduce conference attendees in an engaging way, as well as to promote new contacts and promising business.
Year: 2022
Author(s): Freire, A. C.; Arsénio, E.; Macedo, A. L.; Antunes, M. L.; Capitão, R.; Belinha, M.
Info
Technical tours organization criteria and procedures report
According to the CSA project plan, WP5.2 task objective is to organize technical tours that feature attractive and interactive showcases aiming at engaging participants into novel technologies for all transport modes and enabling stakeholders and their companies to disseminate and even sell their products and applications to all interested parties.
Year: 2022
Author(s): Capitão, R.; Macedo, A. L.; Arsénio, E.; Antunes, M. L.; Freire, A. C.
Editor: TRA LISBON 2022
Info
Data Repository Rules. Deliverable 10.4
This report is part of HYDRALAB+ Work Package 10, which seeks to strengthen the coherence of experimental hydraulic and hydrodynamic research undertaken by the HYDRALAB+ partner organisations. It outlines the work carried out by Samui Design & Management Ltd, supported by HR Wallingford, in relation to the development of a data repository structure that can be adopted by participants of the HYDRALAB+ project.
Year: 2018
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data from physical modeling; Zenodo; Data repository structure
Info
Data Storage Report. RECIPE Task 8.2: Overtopping events in breakwaters under climate change scenarios
Reliable prediction of wave run-up/overtopping and structure damage is a key task in the design and safety assessment of coastal and harbor structures. Run-up/overtopping and damage must be below acceptable limits, both in extreme and in normal operating conditions, to guarantee the stability of the structure and the safety of people and assets on and behind the structure. The mean-sea-level rise caused by climate change and its effects on wave climate may increase the number and intensity of run-up/overtopping events and make the existing coastal/harbor structures more vulnerable to damage.Accurate estimates, through physical modelling, of the statistics of overtopping waves for a set of climate change conditions, are needed. The research project HYDRALAB+ (H2020-INFRAIA-2014-2015) gathers an advanced network of environmental hydraulic institutes in Europe, which provides access to a suite of environmental hydraulic facilities. They play a vital role in the development of climate change adaptation strategies, by allowing the direct testing of adaptation measures and by providing data for numerical model calibration and validation. The use of physical (scale) models allows the simulation of extreme events as they are now, and as they are projected to be under different climate change scenarios.The enclosed dataset refers to the experimental work developed at LNEC within HYDRALAB+ and considers 2D damage and overtopping tests for a rock armor slope, with four different approaches to represent storms. Data of free surface elevation, overtopping and damage is presented.
Year: 2018
Author(s): Fortes, C. J. E. M.; Mendonça, A. C.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Capitão, R.
Keywords: Climate change; Overtopping; Data repository
Info
Facilitating the re-use and exchange of experimental data. Task 10.1 Critical review. D10.2 Critical Review of data flux between laboratory models, numerical models and field case studies
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.2 of the HYDRALAB+ project, entitled
Year: 2018
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Field data; Numerical modeling data; Physical modeling data; Data flux
Info
Facilitating the re-use and exchange of experimental data. Task 10.2 Data Standards and Licenses. D 10.3 Data Standards Report
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.3 of the HYDRALAB+ project, entitled
Year: 2018
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data management options; Experimental data; Data formats
Info
Protocols for representing variability and unsteadiness in flume facilities. Deliverable Number 8.2
This deliverable is related to task 8.2
Year: 2018
Author(s): Mendonça, A. C.; Fortes, C. J. E. M.; Lemos, R.; Capitão, R.; Neves, M. G.; Reis, M. T. L. G. V.
Keywords: Extreme events; Climate change; Variability in flume facilities
Info
Sistema de previsão, alerta e gestão de riscos causados pela agitação marítima - Relatório inicial Arquitetura e características gerais do sistema para os portos de Madalena do Pico, São Roque do Pi
Neste relatório inicial são apresentadas a arquitetura e as caraterísticas gerais dos protótipos do sistema de previsão, alerta e gestão de riscos causados pela agitação marítima para os portos de Madalena do Pico, São Roque do Pico e Praia da Vitória. Os três protótipos em desenvolvimento têm por base uma arquitetura semelhante, com características distintas, nomeadamente no que respeita à localização dos dados de base, às malhas computacionais utilizadas e às características físicas das fronteiras, tanto no plano horizontal (interface terra-mar), como no vertical (batimetria dos fundos). Caracteriza-se o layout geral dos portos, bem como a sua morfologia e operabilidade.
Year: 2018
Author(s): Pinheiro, L.; Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.
Keywords: Porto de Praia da Vitória; Porto de São Roque do Pico; Porto de Madalena do Pico; Agitação marítima; Alerta e gestão de riscos; Sistema de previsão
Info
ANÁLISE TEMPORAL DE REGISTOS DA ELEVAÇÃO DA SUPERFÍCIE LIVRE E DE VELOCIDADE EM ENSAIOS EXPERIMENTAIS
N/A
Year: 2014
Number Pages:
107p.
Author(s): Ramos, A.; Gabriel. S.; Simão, J.; Passarinho, A.; Lemos, R.; Fortes, C. J. E. M.
|
|
|
Outro
Info
Relato da missão a Bruxelas (28 a 30 de Outubro de 1998) para participação na 10ª Reunião da Acção Concertada Added Value Services in VTMIS do Programa Comunitário de I&D TRANSPORTS . Relatório efe
N/A
Year: 1998
Number Pages:
3 p.
Author(s): Covas, J. A.
Editor: ******
Info
Short-term stochastic numerical and physical simulation of sea waves - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI, na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
53 p.
Author(s): Capitão, R.; Pires Silva, A.; Medina, J. R.; Carvalho, M. M.
Editor: ******
Info
Transformações Não-Lineares de Ondas Marítimas em Zonas Costeiras - Proposta de Projecto de Investigação apresentada ao Programa PRAXIS XXI , na área científica de Engenharia Civil
N/A
Year: 1998
Number Pages:
50 p.
Author(s): Covas, J. A.; Fortes, C. J. E. M.
Editor: ******
Info
V Programa Quadro da União Europeia. Preparação da discussão dos Programas Específicos. Documento de trabalho da Comissão (COM (97) 553 Final). Grupo de Trabalho 6 Sustainable Mobility and Intermod
N/A
Year: 1998
Number Pages:
2 p.
Author(s): Covas, J. A.
Editor: ******
Info
Valores extremos da agitação marítima no Algarve - Proposta de Projecto de Investigação apresentado ao Programa de Intervenção nos Laboratórios do Estado (MCT-FCT), sub-projecto Valorização e Protec
N/A
Year: 1998
Number Pages:
11 p.
Author(s): Carvalho, M. M.; Capitão, R.
Editor: ******
|