Publications

The boundary layer concept is applied to the flow around the nose of a streamlined train. In general, that flow is not axisymmetric due to the shape of the nose and the crosswind component of the relative incoming velocity. This departure from axisymmetry produces a transverse pressure gradient that is responsible for skewing an otherwise plane boundary layer. An empirical correlation, dependent on the longitudinal velocity and one unknown parameter, is used to represent the transverse velocity profile. The value of that unknown parameter is obtained from the momentum equations integrated streamwise inside the boundary layer. A visual comparison was carried out between the numerical simulations and the skin shear pattern of a scale model in a wind tunnel. The qualitative results compare well, the numerical model being able to locate the position of the main longitudinal vortices on the lee side of the train.

Masonry buildings worldwide exhibited severe damage and collapse in recent strong earthquake events. It is known that their brittle behavior, which is mainly due to the combination of low tensile strength, large mass and insufficient connection between structural elements, is the main limitation for their structural implementation in residential buildings. A new construction system for masonry buildings using concrete blocks units and trussed reinforcement is presented here and its seismic behavior is validated through shaking table tests. Dynamic tests of two geometrically identical two-story reduced scale (1:2) models have been carried out, considering artificial accelerograms compatible with the elastic response spectrum defined by the Eurocode 8. The first model was reinforced with the new proposed system while the second model was built with unreinforced masonry. The experimental analysis encompasses local and global parameters such as cracking patterns, failure mechanisms, and in-plane and out-of-plane behavior in terms of displacements and lateral drifts from where the global dynamic behavior of the two buildings is analyzed comparatively. Finally, behavior factors for the design recommendations in case of unreinforced masonry are also evaluated.

The out-of-plane response of walls in existing stone masonry buildings is one of the major causes of vulnerability commonly observed in post-earthquake damage surveys. In this context, a shaking table (ST) test campaign was carried out on a full-scale masonry façade mainly focusing on the characterization of its out-of-plane overturning behaviour. The structure tested on the ST is a partial reproduction of an existing building from Azores, damaged during the 9 July 1998 Faial earthquake. The definition of the tested specimen as well as the selection of the input ground motion is reported in this paper. A specific emphasis is given to the definition of the time-history to be applied during the tests because it was felt as an essential and crucial part of the work to obtain the desired overturning behaviour. The accelerogram to be imposed was selected from a large set of accelerograms (74) by means of a step-by-step procedure on the basis of several numerical analyses resorting to the rocking response of rigid blocks.

The present work describes a shaking table experimental campaign specifically developed for the characterisation of the out-of-plane response of a full scale stone masonry façade. After the description of the specimen and the selection of the input motion presented in a companion paper (Part 1), the experimental campaign is illustrated and extensively described. The out-of-plane behaviour of the sacco masonry façade is presented in terms of displacements, velocities, and accelerations recorded during the shaking table tests. A one-sided rocking response of the façade was observed prior to collapse. The impacts were clearly identified in the acceleration records. The façade overturning occurred with the expected failure mode, as predicted in the design of the test.Finally, some conclusions are drawn regarding the observed behaviour and particular features of this type of stone masonry constructions, which may influence the global behaviour of the façade.

During seismic action, energy dissipation in structures occurs in structural and non-structural components, as well as in the substructure. Several of these dissipative mechanisms are modelled explicitly in nonlinear dynamic analyses, notably through relatively sophisticated hysteretic finite elements. Nevertheless, in most practical applications, it is not possible to simulate all the physical contributions to energy dissipation.Structural engineers are thus constrained to overcome this limitation by a mathematical artifice, in the form of equivalent linear viscous damping, which accounts for the remaining

A utilização de dispositivos de dissipação de energia é vista como forma eficiente para proteger estruturas contra ações sísmicas. Os dispositivos Amortecedores de Líquido Sintonizados (ALS) são uma forma simples mas eficaz para reduzir a resposta de estruturas face a ações dinâmicas. Este artigo descreve simulações numéricas sobre o comportamento de ALS, isolados e/ou incluídos numa estrutura de transmissão, comparando-as com os resultados obtidos experimentalmente. Para o efeito foi usado um software de acesso livre denominado CLAWPACK com potencialidades para simular os fenómenos que ocorrem no interior de ALSs. O CLAWPACK consiste num conjunto de rotinas em Fortran desenvolvidas para obtenção de soluções numéricas de sistemas hiperbólicos de equações parcialmente diferenciais no tempo, como é o caso dos fenómenos não-lineares subjacentes à shallow water wave theory. Foram necessárias adaptações e ajustes em algumas das rotinas principais para permitir a simulação das excitações dinâmicas pretendidas. Nas simulações numéricas são variados alguns parâmetros, em que se incluem a altura de água, a amplitude de excitação e o número de dispositivos. Os principais resultados obtidos são comparados, com os resultados obtidos experimentalmente, tanto para dispositivos isolados como para dispositivos incluídos nas estruturas ensaiadas. As principais conclusões obtidas serão também apresentadas.

N/A

As tubagens enterradas constituem componentes principais de sistemas que permitem assegurar o bem estar e o desenvolvimento da sociedade, nomeadamente no que respeita ao abastecimento de água, à drenagem de águas residuais, ao transporte de energia e à comunicação.Com a consolidação das malhas urbanas, tem-se assistido a uma crescente preocupação, não só com a construção, mas em especial com a fase de utilização desses sistemas, tanto nas atividades de exploração (operação e manutenção) como de fim de vida (reabilitação e substituição). Adicionalmente, existe um conjunto crescente de preocupações mais vasto do que as questões operacionais correntes, que inclui os efeitos de fenómenos naturais, como os sismos. As abordagens de gestão do risco permitem ter em conta estes fenómenos e lidar explicitamente com a incerteza que lhes está associada.No contexto da problemática da gestão do risco sísmico de tubagens enterradas, apresenta-se um levantamento de modelos para avaliação da respetiva vulnerabilidade. No âmbito deste artigo é proposta uma abordagem para incorporar a variabilidade probabilística na modelação da vulnerabilidade sísmica de tubagens enterradas. Os resultados obtidos com a metodologia proposta são comparados com a gama de variação da vulnerabilidade sísmica apresentada pela American Lifelines Alliance.

N/A

N/A

A group of five Portuguese experts on earthquake engineering visited the Los Angeles region after the 17 January 1994 Northridge earthquake. The observations mad during the field trip are briefly reports. Discussion is made on the behaviour of different types of structures, namely, masonry, wooden, reinforced concrete and steel structures, as well as special structural typologies such as precast parking lots, tilt-ups and bridges. The presentation is illustrated by means of a few cases, for which the causes of malfunctioning were anticipated.Mention is also made to the behaviour of lifelines, such as electricity, gas and water supply, sewage systems and telephones. The damage assessment is viewed under the light of the ground motion severity.A description of the organizational aspects and procedures adopted for the inspection, immediate reinforcement, recovery and reconstruction of the main buildings, bridges and other utilities are also referred.

Esta comunicação apresenta a conceção, o projeto, a instalação e o planeamento da utilização durante os dois primeiros anos do simulador sísmico triaxial que brevemente começará a funcionar no LNEC. Este simulador destina-se ao ensaio dinâmico até á rotura de grandes modelos de edifícios e ponte (até 60t). Este simulador realiza uma conceção inovadora, que se traduz essencialmente pela eliminação dos 3 graus de liberdade de rotação através de 3 sistemas mecânicos constituídos por uma barra de torção, duas manivelas e duas bielas.

The paper presents the results that permit the identification of optimal design methods for building structures in terms of a eccentricity and are calibrated for probability of failure, evaluated for critical scenarios of expected earthquake intensities.

Some fundamental aspects concerning the overall conception and mechanical design of the new LNEC seismic shaking table, which will have three translational degrees of freedom, are presented. Considerations are made regarding its adaptive control, pointing out the interactions between the behaviour of the mechanical and control systems as far the overall performance of the seismic shaking table is concerned. Lastly, some considerations are also presented on the special building that houses the shaking table.

In this paper we an analytical model to study the hysteretic behavior, under cyclic loading, of RC frames infilled with masonry panels.The calibration of the parameters which define the analytical model, was performed according to the experimental results obtained with three infilled RC frames models and one bare frames model tested at the LNEC.With a good selection of parametric values, the fairly good fitting between analytical an experimental results, allows to conclude that this model can be used in the more broader framework of Earthquake Engineering and structural reliability of buildings under large intensity earthquakes.

A stochastic model of earthquake ground motion, with non-stationary amplitude and frequency content, is presented. This model is quantified on the basis of the information available from seismic hazard studies and strong ground motion seismology with the purpose of generating artificial accelerograms to be used in nonlinear analysis and design of structures. The stochastic model is defined by a

This paper presents the las developments on seismic hazard analysis directed to the computation of strong ground motion parameters to be applied to nonlinear structural analysis (Campos Costa,1992). It follows the Ishikama and Kameda approach (1988), and makes an application to the Lisbon site. Inhere, the methodology and the most probable seismic scenarios are presented. In an accompagning paper (Duarte et al, 1992), time series generation is obtained for a long distance and short distance earthquake scenarios.

This paper presents, in the light of LNEC experience in Earthquake Engineering studies, the limitations and advantages of shaking table testing of reinforced concrete and masonry structures. It starts with a general assessment of the contribution of shaking table facilities to the mitigation of earthquake risks and proceeds with a discussion of some specific problems of shaking table performance and testing procedures, like shaking table design alternatives, self-tuning control and numerical evaluation.

A methodology for the definition and quantification of behaviour coefficients to be used in the earthquake design of structure is presented. These coefficients are defined for specific design methods and are quantified by a target value of the probability of collapse. The methodology is quantified through the analysis and safety checking of structures defined by single variable models.

Nesta comunicação apresenta-se uma metodologia de quantificação de coeficientes de ductilidade de edifícios em betão armado que apresentam irregularidades em planta, e que possuem uma dada probabilidade de ruína.Foram considerados edifícios de 8 pisos com dimensões em planta 20x15 m2, os elementos resistentes a forças horizontais são pórticos planos e paredes estruturais, sendo a determinação dos valores resistentes elásticos limites feito em função de um dado processo de dimensionamento.Posteriormente, recorrendo a algoritmos de integração passo a passo, acedeu-se ao comportamento inelástico dos edifícios sob a ação sísmica intensa. Deste modo, obtiveram-se os valores máximos das ductilidades impostas, definidas em termos das relações momentos-curvaturas nas secções extremas dos elementos de barra, e para valores crescentes de ação sísmica.O cálculo dos coeficientes de ductilidade foi efetuado tendo em atenção quer os valores das probabilidades de serem excedidas as ductilidades disponíveis quer os potenciais mecanismos de colapso de cada edifício.

This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe

The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.

The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies

Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.

In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.

O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.

Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107

Most of the Lisbon 18th century timber-framed masonry

Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.

When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko

A non

N/A

This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM

Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte

Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.

O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação

N/A

This report addresses the National Laboratory for Civil Engineering (LNEC) participation in Subproject 10 Earthquake disaster scenario predictions and loss modelling for urban areas. More precisely this report was developed in order to accomplish the 24 months LESSLOSS deliverable nº 85, which achieves loss estimates for the Metropolitan Area of Lisbon (MAL), for pre-defined scenarios earthquake. These loss estimations represent the reference situation to be compared with revised loss estimates after implementing mitigation actions with the ultimate goal of being established, in the next deliverable, the

N/A

N/A

N/A

The present report describes the construction of a model in limestone masonry for the user Group 3 oh the ECOLEADER Project, led by IRIDEX Construction Group, and the first phase of the experimental program developed in LNEC. The description of the construction, a photographic report and the results obtained on the characteristics tests made on the mortars used in the construction are presented.The construction was carried out by contractor José dos Santos Paixão on the basics of model details and materials specifications proposed by the User group 3, being NESDE/LNEC responsible for the guidance and supervision of the works.

This report describes the first phase activity of the Portuguese group in the Precast Structures EC8 research projet. The Portuguese group is composed by Laboratório Nacional de Engenharia Civil (LNEC) and the Civibral, S.A. Precast Company.In this phase, seismic test were made in the LNEC

The present report addresses the first twelve months of LNEC participation in LESSLOSS

The dynamics of rigid bodies was studies by long time, because this phenomenon is important in the seismic security of some types of structures. However, there are few experimental studies. This job shows the experimental test carried out at the Laboratório Nacional de Engenharia Civil (LNEC) of Portugal. Four blue granites stones were tested, each one with different geometrical characteristics, under harmonic and random motions.A numerical simulation was carried out with the Discrete Element Method (DEM). This method has shown to be a good tool in the study of the dynamics of rigid bodies. It was proposed a new methodology to find the parameters of the DEM by using the parameters of classical theory.

The project LESSLOSS

Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.

Análise da forma das edificações nas ações do vento

As condicionantes arquitetónicas e de urbanização na ventilação natural

Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento