Papers
Info
A semi-analytical model of the 3D boundary layer over the streamlined nose of a train.
The boundary layer concept is applied to the flow around the nose of a streamlined train. In general, that flow is not axisymmetric due to the shape of the nose and the crosswind component of the relative incoming velocity. This departure from axisymmetry produces a transverse pressure gradient that is responsible for skewing an otherwise plane boundary layer. An empirical correlation, dependent on the longitudinal velocity and one unknown parameter, is used to represent the transverse velocity profile. The value of that unknown parameter is obtained from the momentum equations integrated streamwise inside the boundary layer. A visual comparison was carried out between the numerical simulations and the skin shear pattern of a scale model in a wind tunnel. The qualitative results compare well, the numerical model being able to locate the position of the main longitudinal vortices on the lee side of the train.
Year: 2013
Number Pages:
78-88pp.
Author(s): Pereira, I.; André, J.M.C.S.
: Journal of Wind Engineering and Industrial Aerodynamics
Editor: ELSEVIER
Keywords: Longitudinal vortices; Skewed boundary layer; Three-dimensional boundary layer; Train aerodynamics
Info
Experimental investigation on the seismic performance of masonry buildings using shaking table testing
Masonry buildings worldwide exhibited severe damage and collapse in recent strong earthquake events. It is known that their brittle behavior, which is mainly due to the combination of low tensile strength, large mass and insufficient connection between structural elements, is the main limitation for their structural implementation in residential buildings. A new construction system for masonry buildings using concrete blocks units and trussed reinforcement is presented here and its seismic behavior is validated through shaking table tests. Dynamic tests of two geometrically identical two-story reduced scale (1:2) models have been carried out, considering artificial accelerograms compatible with the elastic response spectrum defined by the Eurocode 8. The first model was reinforced with the new proposed system while the second model was built with unreinforced masonry. The experimental analysis encompasses local and global parameters such as cracking patterns, failure mechanisms, and in-plane and out-of-plane behavior in terms of displacements and lateral drifts from where the global dynamic behavior of the two buildings is analyzed comparatively. Finally, behavior factors for the design recommendations in case of unreinforced masonry are also evaluated.
Year: 2013
Number Pages:
1157
Author(s): Campos Costa, A.; Lourenço, P.; Vasconcelos, G.; Avila, L.; Mendes, N.; Pedro Alves, J.
: Bulletin of Earthquake Engineering
Editor: Springer
Volume:
Vol. 11, Issue 4.
Keywords: Shaking table; Behavior factor; Bed joint reinforcement; Seismic performance; Concrete block masonry
Info
Out-of-plane behaviour of a full scale stone masonry facade. Part 1: specimen and ground motion selection
The out-of-plane response of walls in existing stone masonry buildings is one of the major causes of vulnerability commonly observed in post-earthquake damage surveys. In this context, a shaking table (ST) test campaign was carried out on a full-scale masonry façade mainly focusing on the characterization of its out-of-plane overturning behaviour. The structure tested on the ST is a partial reproduction of an existing building from Azores, damaged during the 9 July 1998 Faial earthquake. The definition of the tested specimen as well as the selection of the input ground motion is reported in this paper. A specific emphasis is given to the definition of the time-history to be applied during the tests because it was felt as an essential and crucial part of the work to obtain the desired overturning behaviour. The accelerogram to be imposed was selected from a large set of accelerograms (74) by means of a step-by-step procedure on the basis of several numerical analyses resorting to the rocking response of rigid blocks.
Year: 2013
Number Pages:
2081
Author(s): Campos Costa, A.; Costa, A.; Penna, A.; Arêde, A.
: Earthquake Engineering & Structural Dynamics
Editor: John Wiley & Sons, Ltd.
Volume:
Vol. 42.
DOI:
10.1002/eqe.2313
Keywords: Full scale; Ground motion selection; Rocking; Masonry; Out-of-plane; Shaking table
Info
Out-of-plane behaviour of a full scale stone masonry façade. Part 2: shaking table tests
The present work describes a shaking table experimental campaign specifically developed for the characterisation of the out-of-plane response of a full scale stone masonry façade. After the description of the specimen and the selection of the input motion presented in a companion paper (Part 1), the experimental campaign is illustrated and extensively described. The out-of-plane behaviour of the sacco masonry façade is presented in terms of displacements, velocities, and accelerations recorded during the shaking table tests. A one-sided rocking response of the façade was observed prior to collapse. The impacts were clearly identified in the acceleration records. The façade overturning occurred with the expected failure mode, as predicted in the design of the test.Finally, some conclusions are drawn regarding the observed behaviour and particular features of this type of stone masonry constructions, which may influence the global behaviour of the façade.
Year: 2013
Number Pages:
2097
Author(s): Campos Costa, A.; Penna, A.; Arêde, A.; Costa, A.; Costa, A.A.
: Earthquake Engineering & Structural Dynamics
Editor: John Wiley & Sons, Ltd.
Volume:
Vol. 42, Issue 14.
DOI:
10.1002/eqe.2314
Keywords: Full scale; Ground motion selection; Rocking; Masonry; Out-of-plane; Shaking table
Info
Seismic energy dissipation in inelastic frames: understanding state-of-the-practice damping models
During seismic action, energy dissipation in structures occurs in structural and non-structural components, as well as in the substructure. Several of these dissipative mechanisms are modelled explicitly in nonlinear dynamic analyses, notably through relatively sophisticated hysteretic finite elements. Nevertheless, in most practical applications, it is not possible to simulate all the physical contributions to energy dissipation.Structural engineers are thus constrained to overcome this limitation by a mathematical artifice, in the form of equivalent linear viscous damping, which accounts for the remaining
Year: 2013
Number Pages:
148-158pp.
Author(s): Correia, A.A.; Almeida, J.P.; Pinho, R.
: Structural Engineering International
Editor: International Association for Bridge and Structural Engineering
Volume:
Vol. 23, Number 2.
Keywords: Force-based element; Inelastic frame; Damping models; Energy dissipation; Nonlinear dynamic analysis
Info
Simulações numéricas do comportamento de amortecedores de líquido sintonizado sujeitos a ações sísmicas
A utilização de dispositivos de dissipação de energia é vista como forma eficiente para proteger estruturas contra ações sísmicas. Os dispositivos Amortecedores de Líquido Sintonizados (ALS) são uma forma simples mas eficaz para reduzir a resposta de estruturas face a ações dinâmicas. Este artigo descreve simulações numéricas sobre o comportamento de ALS, isolados e/ou incluídos numa estrutura de transmissão, comparando-as com os resultados obtidos experimentalmente. Para o efeito foi usado um software de acesso livre denominado CLAWPACK com potencialidades para simular os fenómenos que ocorrem no interior de ALSs. O CLAWPACK consiste num conjunto de rotinas em Fortran desenvolvidas para obtenção de soluções numéricas de sistemas hiperbólicos de equações parcialmente diferenciais no tempo, como é o caso dos fenómenos não-lineares subjacentes à shallow water wave theory. Foram necessárias adaptações e ajustes em algumas das rotinas principais para permitir a simulação das excitações dinâmicas pretendidas. Nas simulações numéricas são variados alguns parâmetros, em que se incluem a altura de água, a amplitude de excitação e o número de dispositivos. Os principais resultados obtidos são comparados, com os resultados obtidos experimentalmente, tanto para dispositivos isolados como para dispositivos incluídos nas estruturas ensaiadas. As principais conclusões obtidas serão também apresentadas.
Year: 2013
Number Pages:
25-34pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.; Guerreiro, L.
: RPEE
Editor: LNEC
Volume:
Série II, nº 13.
Keywords: Sistemas passivos; Simulações numéricas; Mitigação de vibrações; Amortecedores de líquido sintonizado; Proteção sísmica
Info
A segurança sísmica na reabilitação de edifícios - Enquadramento e dimensão política
N/A
Year: 2012
Number Pages:
4pp.
Author(s): Coelho, E.; Bairrão, R.
: Pedra & Cal, Conservação e Reabilitação
Volume:
Nº 53.
Info
Gestão do risco sísmico em tubagens enterradas - O caso dos sistemas de drenagem de águas residuais
As tubagens enterradas constituem componentes principais de sistemas que permitem assegurar o bem estar e o desenvolvimento da sociedade, nomeadamente no que respeita ao abastecimento de água, à drenagem de águas residuais, ao transporte de energia e à comunicação.Com a consolidação das malhas urbanas, tem-se assistido a uma crescente preocupação, não só com a construção, mas em especial com a fase de utilização desses sistemas, tanto nas atividades de exploração (operação e manutenção) como de fim de vida (reabilitação e substituição). Adicionalmente, existe um conjunto crescente de preocupações mais vasto do que as questões operacionais correntes, que inclui os efeitos de fenómenos naturais, como os sismos. As abordagens de gestão do risco permitem ter em conta estes fenómenos e lidar explicitamente com a incerteza que lhes está associada.No contexto da problemática da gestão do risco sísmico de tubagens enterradas, apresenta-se um levantamento de modelos para avaliação da respetiva vulnerabilidade. No âmbito deste artigo é proposta uma abordagem para incorporar a variabilidade probabilística na modelação da vulnerabilidade sísmica de tubagens enterradas. Os resultados obtidos com a metodologia proposta são comparados com a gama de variação da vulnerabilidade sísmica apresentada pela American Lifelines Alliance.
Year: 2012
Number Pages:
4-21pp.
Author(s): Sousa, V.; Luísa Sousa, M.; Campos Costa, A.; Matos, J. S.; Almeida, N.
: Revista Águas & Resíduos
Editor: APESB
Volume:
Série III, N.º 17.
Keywords: Vulnerabilidade sísmica; Tubagem enterrada; Sistema de drenagem; Risco Sísmico
Info
On dynamic control of structural vibrations. Research activities conducted within the COVICOCEPAD Project
N/A
Year: 2012
Number Pages:
1pp.
Author(s): Bairrão, R.
: NED University Journal of Research
Volume:
Thematic Issue on Earthquakes.
Info
Shaking table experimental researches aimed at the protection of structures subjected to dynamic loading
N/A
Year: 2012
Number Pages:
6pp.
Author(s): Bairrão, R.
: The Open Construction and Building Technology Journal
Volume:
Volume 6.
|
Comunicação
Info
Ensaio aerodinâmico de uma ponte pedonal suspensa
O trabalho apresentado refere-se à avaliação do comportamento aerodinâmico da ponte pedonal suspensa 516 Arouca. Para tal realizaram-se ensaios em túnel de vento sobre um modelo reduzido de modo a obter os seus coeficientes aerodinâmicos estáticos e a resposta dinâmica.Os ensaios estáticos contemplaram diferentes configurações: i) tabuleiro; ii) tabuleiro e catenárias; iii) tabuleiro com pessoas, e; iv) tabuleiro e pórticos de suporte aos cabos de estabilização. Para os ensaios dinâmicos foi ensaiado apenas o tabuleiro.Para estes últimos ensaios, dado que o principal modo de deslocamento é lateral (em baloiço), houve que implementar um esquema de suspensão apropriado.
Year: 2021
Number Pages:
15.
Author(s): Marques da Silva, F.
Editor: Associação Portugusa de Análise Experimental de Tensões
Keywords: Túnel de vento; Aerodinâmica; : Pontes suspensas
Info
Análise não linear de um conjunto de edifícios em placa no bairro de alvalade: avaliação preliminar de estabilidade e previsão dos mecanismos de colapso
Os edifícios tipo
Year: 2019
Number Pages:
12p.
Author(s): Bernardo, V.; Candeias, P.; Campos Costa, A.; Costa, A.
Editor: Comissão Organizadora
Keywords: Modos de colapso; Análise preliminar de estabilidade; Applied Element Method; Ensaios de caraterização dinâmica; Edifícios tipo
Info
Comportamento de paredes de alvenaria sujeitas a ações no plano: análise numérica e validação experimental
As estruturas de alvenaria têm nos demonstrado ao longo dos anos grande suscetibilidade perante a ação dos sismos. Para que possam ser definidas e implementadas estratégias de mitigação é importante compreender a vulnerabilidade destas estruturas.O presente estudo pretende analisar o comportamento de duas paredes de alvenaria, com e sem reforço, sujeitas a ações cíclicas no seu plano e sob carregamento vertical. Como proposta de reforço e melhoria do comportamento da parede foi utilizada rede de fibra de vidro e argamassa à base de cal. Numa primeira fase será utilizado um programa de cálculo avançado para análises não lineares, baseado na formulação do Applied Element Method (AEM) [1], de forma a prever o comportamento das paredes até ao colapso. Os resultados serão comparados e discutidos sendo feita a validação experimental do modelo numérico e da formulação utilizada.
Year: 2019
Number Pages:
12p.
Author(s): Bernardo, V.; Mera Marques, A.; Candeias, P.; Campos Costa, A.; Ferreira, J.
Editor: Comissão Organizadora
Keywords: Validação experimental; Previsão numérica; Applied Element Method; Paredes de alvenaria
Info
Experimental response of non-seismically designed URM buildings subjected to induced seismicity
The response of three full-scale unreinforced masonry buildings, without specific seismic detailing, as observed in shake table testing at LNEC for a seismic action representative of induced seismicity, is presented. The first building specimen simulated the upper floor and roof of the end-unit of a two-storey terraced house, built with unreinforced cavity walls, a reinforced concrete slab and a pitched timber roof. The second specimen was a replica of the roof of the first building. The third specimen represented instead a one-story detached pre-1940
Year: 2019
Number Pages:
12p.
Author(s): Correia, A.A.; Mera Marques, A.; Campos Costa, A.; Candeias, P.; Bernardo, V.; Tomassetti, U.; Graziotti, F.; Kallioras, S.
Editor: Comissão Organizadora
Keywords: Collapse; Limit states; Induced seismicity; Full-scale shake table test; Unreinforced masonry building
Info
Fiabilidade estrutural de edifícios existentes de betão armado sem dimensionamento sismorresistente
Até à introdução e disseminação do atual regulamento de dimensionamento sismorresistente em 1983, o Regulamento de Segurança e Acções para Estruturas de Edifícios e Pontes (RSA), a generalidade dos edifícios de betão armado eram dimensionados para resistir apenas a cargas gravíticas. O presente estudo pretende caracterizar o comportamento sísmico destes edifícios bem como quantificar a fiabilidade estrutural quando avaliados à luz do Eurocódigo 8 - Parte 3.Por forma a criar um contexto representativo desta classe de edifícios, foram gerados centenas de modelos numéricos que refletem as principais características geométricas e mecânicas dos materiais, e que obedecem às regras e disposições construtivas definidas nos regulamentos nacionais anteriores à introdução do RSA. A análise probabilística dos resultados obtidos para os níveis de perigosidade associados às diferentes regiões doterritório nacional fornece indicações de quais as combinações edifícios/zonas sísmicas que apresentam uma maior vulnerabilidade face à ação sísmica.
Year: 2019
Number Pages:
12p.
Author(s): Sousa, R.; Campos Costa, A.; Candeias, P.; Costa, A.
Editor: Comissão Organizadora
Keywords: Betão armado; Edifícios existentes; Comportamento sísmico; Fiabilidade estrutural
Info
Proposta de uma metodologia para a avaliação expedita de edifícios de existentes de betão armado
A avaliação da segurança sísmica de edifícios existentes tem como quadro de referência a NP EN 1998-3; 2017. A complexidade destes procedimentos, aliada ao reconhecimento de que uma parte significativa do território nacional apresenta uma sismicidade média/baixa, torna a aplicação desta norma complexa para a maioria dos edifícios existentes de pequeno a médio porte.Neste contexto, foi desenvolvido um estudo probabilístico com o objetivo de definir dois procedimentos alternativos que, não pretendendo substituir a regulamentação existente, permitem avaliar a segurança sísmica de edifícios de uma forma expedita, com base nas propriedades geométricas e mecânicas dos seus elementos verticais.Não obstante a sua simplicidade, estes métodos permitem assegurar o mesmo nível de fiabilidade estrutural para os diferentes graus de perigosidade sísmica em Portugal, bem como um nível de segurança inversamente proporcional ao nível de complexidade dos mesmos, tendo como referência a NP EN 1998-3; 2017.
Year: 2019
Number Pages:
12p.
Author(s): Sousa, R.; Campos Costa, A.; Candeias, P.; Costa, A.
Editor: Comissão Organizadora
Keywords: Betão armado; Edifícios existentes; Avaliação segurança sísmica
Info
Collapse shake-table test on a URM-timber roof substructure
Typical low-rise masonry construction in regions such as Europe, Australia and New Zealand consists of cavity or solid URM walls covered with various timber roof configurations generally supported by masonry gables. The flexibility of these light timber roof systems has been reported to have significant effect on the seismic performance of the structure as a whole. Post-earthquake observations and experimental outcomes highlighted the large vulnerability of the URM gable walls to the development of overturning mechanisms, both due to the out-of-plane excitations and the in-plane timber diaphragm deformability. This paper presents a full-scale collapse shake-table test on a Dutch roof substructure composed by wooden planks supported by timber beams lying on masonry gable walls. After attaining the collapse of the gable walls, the timber roof diaphragm was subjected to a supplementary quasi-static cyclic pushover test for a complete characterization of the system response. The test is a part of a wider research project aimed at assessing the vulnerability of URM buildings in Groningen, a region of the Netherlands not naturally prone to seismic events, but which has recently been exposed to induced seismicity. The presented results include the damage evolution, the collapse mechanism and the hysteretic response of the specimen.
Year: 2018
Number Pages:
12p.
Author(s): Correia, A.A.; Tomassetti, U.; Campos Costa, A.; Penna, A.; Graziotti, F.; Magenes, G.
Editor: EAEE/ETAM
Keywords: Collapse; Roof; Timber; Unreinforced masonry; Full-scale shake-table test
Info
Full-scale shake-table tests of URM buildings subjected to induced ground motions
This paper discusses the results of three dynamic shake-table tests, performed on full-scale unreinforced masonry buildings without specific seismic detailing. The testing program is part of a wider research project aimed at assessing the seismic vulnerability of buildings typical of the Groningen region, located in Northeast of the Netherlands. This area, historically not prone to tectonic ground motions, in the recent years has been subjected to earthquakes induced by reservoir depletion due to gas extraction. The first building specimen simulated the end-unit of a two-story terraced house, built with unreinforced cavity walls. These walls were composed of an inner load-bearing leaf, made of calcium silicate bricks supporting the floors, and an outer veneer, made of clay bricks with aesthetic and weather-protection function. The two leafs were interconnected by distributed metal ties. The floors consisted of reinforced concrete slabs, providing rigid diaphragms in their plane. The pitched roof was made of longitudinal timber purlins, supported by end gables perpendicular to the shaking direction, and wood boards. The second specimen was a replica of the second story and the attic of the first building, with identical details for walls, slab, and roof framing tested to study the collapse mechanism. The third specimen represented instead a one-story detached pre-1940s house, built with double-wythe unreinforced clay masonry walls. The prototype structure was designed to include large openings and a re-entrant corner, causing significant horizontal irregularities. The first floor was made of timber beams and planks, resulting in a flexible diaphragm. The steep-pitch roof consisted of a series of timber trusses connected by wood purlins and boards. The two façades perpendicular to the shaking direction were designed in order to represent two common gable geometries.
Year: 2018
Number Pages:
12p.
Author(s): Graziotti, F.; Tomassetti, U.; Correia, A.A.; Penna, A.; Magenes, G.; Guerrini, G.
Editor: EAEE/ETAM
Keywords: Induced Seismicity; Collapse; Roof; Unreinforced masonry building; Full-scale shake-table test
Info
Towards a uniform earthquake risk model for Europe
Seismic risk has been the focus of a number of European projects in recent years, but there has never been a concerted effort amongst the research community to produce a uniform European risk model. The H2020 SERA project has a work package that is dedicated to that objective, with the aim being to produce an exposure model, a set of fragility/vulnerability functions, and socio-economic indicators in order to assess probabilistic seismic risk at a European scale. The partners of the project are working together with the wider seismic risk community through web tools, questionnaires, workshops, and meetings. All of the products of the project will be openly shared with the community on both the OpenQuake platform of the Global Earthquake Model (GEM) and the web platform of the European Facilities for Earthquake Hazard and Risk (EFEHR).
Year: 2018
Number Pages:
10p.
Author(s): Romão, X.; Correia, A.A.; Crowley, H.; Rodrigues, D.; Silva, V.; Despotaki, V.; Castro, J.M.; Akkar, S.; Hancilar, U.; Pitilakis, K.; Pitilakis, D.; Belvaux, M.; Wiemer, S.; Danciu, L.; Bursi, O.S.; W
Editor: EAEE/ETAM
Keywords: European risk; Socio-economic vulnerability; Fragility model; Exposure model; Seismic risk
Info
A fibre-based frame element with explicit consideration of bond-slip effects
Reinforced concrete (RC) frames subjected to seismic loading often depict localized member-end deformations due to strain penetration effects between adjacent members, such as beam-column and column-footing joints. Past experimental programs indicate that the bond-slip deformations occurring at the interface between the reinforcement and the surrounding concrete can contribute up to 40% of the lateral deformation of the RC members.Despite the recognized importance of strain penetration effects on the response of RC structures, the consideration of such effects in numerical models is still limited. The employment of advanced bond-slip models within detailed finite element formulations, capable of simulating continuous domains with highly discretized meshes, has witnessed great advances over the recent years with encouraging results. Nonetheless, this modelling approach is computationally heavy and hence inapplicable for practical seismic (nonlinear) analysis of structures.Alternatively, the use of beam-column elements with lumped or distributed plasticity is a more computationally efficient and engineering-friendly modelling approach. Unfortunately, the elements of this type available in conventional numerical packages did not yet consider an explicit simulation of the interface between the reinforcing bars and the surrounding concrete along their embedment length. In other words, the inclusion of bond-slip effects in beam element models has been essentially achieved through simplified formulations based on empirical relationships.The present study aimed at overcoming the foregoing limitation by developing an explicit bond-slip model applicable to general fibre-based beam-column elements. Using a state-of-the-art bond-slip constitutive model, the current paper introduces a zero-length element that computes the localized member-end deformations accounting for the bond-slip response at each reinforcing bar of a given RC section. Along with the material properties and anchorage conditions, the proposed nonlinear model also accounts for cyclic degradation and rebar yielding effects. Validation studies conducted with the proposed numerical formulation reveal a good agreement with past experimental tests, evidencing an important stability and accuracy at the expense of an acceptable additional computational effort.
Year: 2017
Number Pages:
12p.
Author(s): Sousa, R.; Correia, A.A.; Almeida, J.P.; Pinho, R.
Editor: ACHISINA, IAEE
Keywords: Nonlinear analysis; Frame; Reinforced concrete; Bond-slip
|
Books
Info
Historical earthquake-resistant timber framing in the mediterranean area
This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe
Year: 2016
Number Pages:
468p.
Author(s): Cruz, H.; Saporiti Machado, J.; Campos Costa, A.; Candeias, P.; Catarino, J. M.
Editor: Springer
Volume:
Vol. 1.
Keywords: Heart 2015 Conference; Historic Masonry; Performance-based Assessment; Structural Health Monitoring; Timber-Framed Construction Systems; Seismic-Resistant Timber Frames; Historical Constructive Analysis; Historical Timber-Framed Walls
Info
Assessment of the seismic capacity of stone masonry walls with block models
The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.
Year: 2011
Number Pages:
221-236pp.
Author(s): Lemos, J. V.; Campos Costa, A.; Bretas, E. M.
: Computational Methods in Earthquake Engineering
Editor: Springer
Volume:
Vol. 21.
Keywords: RTigid blocks; Discrete elements; Seismic assessment; Masonry structures
Info
Earthquake disaster scenario prediction and loss modelling for urban areas
The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies
Year: 2007
Number Pages:
180p.
Author(s): Campos Costa, A.; Carvalho, A. M.
Editor: IUSS Press
Keywords: Shaking scenarios
Info
European manual for in-situ assessment of important existing structures. LessLoss Sub Project 5-In-situ assessment, monitoring and typification of buildings and infrastructure
Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.
Year: 2007
Number Pages:
195p.
Author(s): Campos Costa, A.; Candeias, P.; Mendes, L.; Flesch, R.; Pellegrini, R.; Friedl, H.; Hoffmeister, B.; Oppe, M.; Veit-Egerer, R.; Wenzel, H.; Eusebio, M.
Editor: IUSS Press
Keywords: Structures; Earthquake
Info
Modal analysis from ambient vibration survey of bridges: LNEC experience
In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.
Year: 1999
Number Pages:
712-718pp.
Author(s): Rodrigues, J.; Campos Costa, A.
: Proceedings of the 17th International Modal Analysis Conference : February 8 - 11, 1999 / IMAC XVII.
Editor: SEM
Volume:
Vol. 3727.
Keywords: Dynamic properties; Bridge structures
Info
O Sismo de Northridge, Los Angeles, de 17 Janeiro de 1994. Ensinamentos para Portugal.
O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.
Year: 1995
Number Pages:
165p.
Author(s): Oliveira, C.S.; Costa, A.; Campos Costa, A.; Azevedo, J.; Delgado, R.M.
Editor: IST e FEUP
Keywords: Northridge earthquake; Earthquake effects
|
Capítulo de Livro
Info
Shaping favorable beliefs towards seismic protection through risk communication: A pilot-experience in two Lisbon schools (Portugal).
Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107
Year: 2019
Number Pages:
445-458pp.
Author(s): Silva, D. S.; Vicente, M.; Pereira, A.; Candeias, P.; Ferreira, M.A.; Oliveira, C.S.; Bernardo, R.; Lopes, M.; Henriques, P.
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Non-structural; Protective behaviours; Risk communication; Seismic risk
Info
Characterization of timber masonry walls with dynamic tests
Most of the Lisbon 18th century timber-framed masonry
Year: 2018
Number Pages:
299-309pp.
Author(s): Gonçalves, A.; Candeias, P.; Guerreiro, L.; Ferreira, J.; Campos Costa, A.
: Historical earthquake-resistant timber framing in the mediterranean area
Editor: Springer
Volume:
Vol. 1.
Keywords: Shaking table tests; Timber-masonry walls;
Info
KnowRISK practical guide for mitigation of seismic risk due to non-structural components
Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.
Year: 2018
Number Pages:
309-321pp.
Author(s): Ferreira, M.A.; Oliveira, C.S.; Lopes, M.; Musacchio, G; Candeias, P.; Vicente, M.; Silva, D. S.; O
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Practical guide; Community resilience; Preparedness; Non-structural elements
Info
Elastic and inelastic analyses of frames with a force-based higher-order 3D beam element accounting for axial-flexural-sheartorsional interaction
When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko
Year: 2016
Number Pages:
109-128pp.
Author(s): Correia, A.A.; Almeida, J.P.; Pinho, R.
: Computational Methods in Applied Sciences
Editor: Springer
Volume:
Vol. 3.
Keywords: Inelastic response; Boundary conditions; Flexural-shear-torsional interaction; Higher-order; Force-based; Beam element
Info
A finite-fault modeling of the 1755 Lisbon earthquake sources
A non
Year: 2009
Number Pages:
433-454.
Author(s): Carvalho, A. M.; Campos Costa, A.; Sousa Oliveira, C.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios; Finite-fault modeling
Info
Simulating earthquake scenarios in the european project Lessloss: the case of Lisbon
N/A
Year: 2009
Number Pages:
233-243.
Author(s): Zonno, G.; Carvalho, A. M.; Franceschina, G.; Akinci, A.; Campos Costa, A.; Coelho, E.; Cultrera, G.; Pacor, F.; Pessina, V.; Cocco, M.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios
Info
Shaking table testing
This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM
Year: 2008
Number Pages:
165-196pp.
Author(s): Bairrão, R.
Editor: Springer Verlag
Keywords: Shaking table testing
|
Tese de Doutoramento
Info
Modelos estocáticos para a caracterização da acção sísmica em Portugal Continental
Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte
Year: 2009
Author(s): Carvalho, A. M.
Keywords: Portugal continental; Risco sísmico; Fonte sísmica; Modelos estocásticos; Acção sísmica
Info
Risco sísmico em Portugal Continental
Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.
Year: 2009
Author(s): Sousa, M. L.
Info
Avaliação da vulnerabilidade sísmica de edifícios de alvenaria
O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação
Year: 2008
Author(s): Candeias, P.
Keywords: Reforço sísmico; Vulnerabilidade sísmica; Ensaios sísmicos; Edifícios
|
Relatório Científico
Info
Earthquake risk scenarios for selected European cities
O Laboratório Nacional de Engenharia Civil (LNEC) participa atualmente numa das sete Tarefas, doprojeto Europeu SHARE- Seismic Hazard Harmonization in Europe, mais precisamente na tarefa nº 2,intitulada Requisitos de engenharia e aplicações.O presente relatório de progresso descreve a participação do LNEC na sub-tarefa 2.5 - Cenários derisco sísmico para cidades Europeias selecionadas
Year: 2012
Number Pages:
44.
Author(s): Luísa Sousa, M.; Carvalho, A. M.
Editor: LNEC
Info
Actividade experimental na área dos sistemas passivos para a protecção sísmica de estruturas: Experiência do NESDE - Relatório de estágio
N/A
Year: 2011
Number Pages:
74pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.
Editor: LNEC
Info
Modelos de comportamento dinâmico aplicáveis a amortecedores de líquido sintonizado - Relatório de estágio
No presente relatório pretendem-se apresentar e definir alguns das linhasorientadoras para a simulação do comportamento dinâmico de fluidos no interior deAmortecedores de Líquido Sintonizado (TLDs), de acordo com o proposto na literatura.O problema da modelação do comportamento de fluidos no interior deAmortecedores de Líquido Sintonizado, à semelhança do que acontece parareservatórios, é complexo, sendo apresentados os principais modelos matemáticos emecânicos utilizados na actualidade.Assim serão descritos modelos de comportamento adoptados no casoparticular dos Amortecedores de Líquido Sintonizado (TLDs) e modelos simplificadosde sistemas de 1 (SDOF) ou mais graus (MDOF) de liberdade com com os referidosdispositivos de mitigação de acções dinâmicas acopladosO presente relatório servirá, à semelhança dos relatórios Sistemas passivos,activos, híbridos e semi-activos: Estado dos conhecimentos, Actividade experimentalna área dos sistemas passivos para a protecção sísmica de estruturas: Experiência doNESDE e Modelos de comportamento dinâmico para fluidos no interior dereservatórios como uma das linhas orientadoras para o desenvolvimento dos trabalhospropostos no âmbito do PIP 2009-2012 do NESDE-DE Protecção Sísmica deEstruturas: Reabilitação, reforço e sistemas inteligentes.
Year: 2011
Number Pages:
159pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.
Editor: LNEC
Info
Modelos de comportamento dinâmico para fluidos no interior de reservatórios - Relatório de estágio
N/A
Year: 2011
Number Pages:
176pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.
Editor: LNEC
Info
Sistemas passivos, activos, híbridos e semiactivos para a protecção sísmica de estruturas: Estado dos conhecimentos - Relatório de estágio
N/A
Year: 2011
Number Pages:
226pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.
Editor: LNEC
Info
Estabelecimento de cenários sísmicos para a região do Algarve com base em metodologias probabilísticas - Relatório de Estágio
N/A
Year: 2010
Number Pages:
89pp.
Author(s): RODRIGUES, I.; Sousa, M. L.
Info
NEFOREEE PROJECT
This Report corresponds to Task 2 of the NEFOREEE (New Fields of Research inEarthquake Engineering Experimentation) Project and comprises the description of theLNEC triaxial seismic platform and a presentation of the experimental programdeveloped in the scope of this Project.It is presented a description of the facility and the 3D seismic table with graphicalsupport, drawings of sizing and photographs, as well as its control system. The maininstrumentation available at the NESDE laboratory and used for this test is alsoincluded in this report.The model tested is described as well as the sequence of tests and the correspondingobtained results. Finally a brief analysis of the results is made.
Year: 2009
Number Pages:
325pp.
Author(s): Falcão Silva, M. J.; Campos Costa, A.; Bairrão, R.
Info
RELATÓRIO FINAL DO PROJECTO USUET
O presente relatório final do projecto USuET integra o trabalho já apresentado norelatório de progresso de Sousa & Afonso [2007], nomeadamente no que toca aoscapítulos 2, 3 e parte do capítulo 4 e, adicionalmente, descreve, em detalhe, asactividades desenvolvidas no projecto desde a data desse relatório (secção 4.2, ecapítulos 5 e 6). A parte da investigação conducente à actualização do Simulador deCenários Sísmicos para ambiente WebSIG, aplicado ao Arquipélago dos Açores, não seencontra descrita com o mesmo detalhe, neste relatório, pois enquadra-se na tese demestrado em Sistemas de Informação Geográfica de Afonso [2007], submetida àUniversidade Técnica de Lisboa. A versão definitiva desta tese, cuja discussão se prevêainda em 2008, será enviada oportunamente.
Year: 2008
Number Pages:
90pp.
Author(s): Sousa, M. L.; Afonso, N.
Keywords: Projecto usuet; Análise sistémica
Info
Cyclic tests of joints from a reinforced concrete precast building system
N/A
Year: 2007
Number Pages:
204pp.
Author(s): Mendes, L.; Coelho, E.; Campos Costa, A.
Info
Cyclic tests of joints from a reinforced concrete precast building system
This report describes the second phase activity of the Portuguese group in the Precast Structures EC8 research project. The Portuguese group is composed by Laboratório Nacional de Engenharia Civil (LNEC) and the Civibral, S.A. precast company. This phase follows the shaking table tests of a 2 stories structure of the same precast system, which is commercialized by Civibral. More information about these tests can be found in the repor.The goal of the work presented in this document is to assess the seismic behaviour of column-foundation and beam-column connections from the same precast system. To help achieve this goal, 4 column-foundation and 10 beam-column connections were tested using quasi-static, monotonic and cyclic tests, which were made imposing displacements to the specimens. The column-foundation connections (CFC) can be categorized as socket connections and the beam-column connections (BCC) as dry connections using only mechanical devices to transmit forces between elements. All the specimens were supplied and mounted by Civibral personal.
Year: 2007
Author(s): Mendes, L.; Coelho, E.; Campos Costa, A.
Keywords: Reinforced concrete; Cyclic tests
|
Outro
Info
Sensibilidade climática, capacidade adaptativa e de vulnerabilidades atuais e futuras da AML
Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.
Year: 2019
Author(s): Marques da Silva, F.; Pinto, A.; Machado, P.
Keywords: Energia; Alterações climáticas
Info
A propósito da forma na engenharia do vento
Análise da forma das edificações nas ações do vento
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Aerodinãmica
Info
Forma e desenho urbano - efeitos na ventilação
As condicionantes arquitetónicas e de urbanização na ventilação natural
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Ventilação
Info
Wind and structures
Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento
Year: 2017
Author(s): Marques da Silva, F.
Keywords: Wind tunnel; Actions on structures; Wind engineering
|