Publications

A ventilação natural é uma eficiente estratégia projetual para ocondicionamento térmico passivo de edificações, ocorrendo por açãodos ventos, efeito chaminé ou pela combinação de ambos. Dentre asestratégias de ventilação, destacam-se os sheds, aberturas no telhado,que funcionam como captadores ou extratores de ar, dependendo de sualocalização em relação aos ventos dominantes. O objetivo desse artigo é avaliar ainfluência da variação na geometria dos sheds e na dimensão das aberturas deentrada e saída de ar no desempenho da ventilação natural. O sistema foi avaliadopara os ângulos de incidência dos ventos externos de 0° e 45° (extração) e 135° e180° (captação). A metodologia adotada foi a simulação por Dinâmica dos FluídosComputacional (CFD), utilizando como ferramenta o software CFX. Foramrealizadas análises quantitativas (taxas de renovação de ar/hora e coeficiente depressão nas aberturas) e qualitativas (planos de contorno e vetores de direção eintensidade do fluxo de ar). Os resultados indicam que sheds com geometriasaerodinâmicas e o aumento das aberturas de saída de ar incrementam o fluxo de arinterno. Para os sheds captadores o aumento isolado das aberturas de entrada de arnão proporciona uma melhora significativa na captação dos ventos pela cobertura.

The analysis of the shaking table test of a 3-wall stone masonry structure performed with a discrete element model is presented. The numerical model, created with the code 3DEC, employed a rigid block representation and a Mohr-Coulomb joint model. Joint stiffness calibration to match the experimental natural frequencies is discussed, as well as the boundary conditions to simulate the shake table. Comparisons are made with the measured displacements at key locations, and the modes of deformation and fracture of the walls. The DEM model was able to reproduce important features of the shaking table tests. The experimental deformation and near collapse patterns were clearly identifiable in the numerical simulations, which produced displacements within the observed orders of magnitude, for the various levels of excitation.

Strong ground motion prediction based on finite-fault simulation requires the identification of the fault (strike, dip, length and width), source kinematics parameters (stress drop, rupture velocity and slip distribution), regional crustal properties (geometrical spreading, anelastic structure, and upper crustal amplification and attenuation parameters) and the determination of amplification effects due to the local site geology. The general purpose of this study is to understand source and attenuation properties in the Azores, by the determination of stress drop, quality factor and kappa, through records obtained by the Portuguese digital seismic and accelerometer network. Source Spectra were obtained, for each record, after correcting observed spectra from geometrical spreading and anelastic attenuation effect: quality factor was estimated based on coda decay in the time domain and the kappa parameter was estimated by fitting the high-frequency decay of the acceleration spectrum with a straight line in a log-linear scale. Mean stress drop value was obtained considering that

The assessment of wind energy resource for the development of deep offshore wind plants requires the use of every possible source of data and, in many cases, includes data gathered at meteorological stations installed at islands, islets or even oil platforms - all structures that interfere with, and change, the flow characteristics. This work aims to contribute to the evaluation of such changes in the flow by developing a correction methodology and applying it to the case of Berlenga island, Portugal. The study is performed using computational fluid dynamic simulations validated by wind tunnel tests. In order to simulate the incoming offshore flow with CFD models a wind profile, unknown a priori, was established using observations from two coastal wind stations and a power law wind profile was fitted to the existing data (alfa=0.165). The results show that the resulting horizontal wind speed at 80 m above sea level is 16% lower than the wind speed at 80 m above the island for the dominant wind direction sector.

An innovative higher-order beam theory, capable of accurately taking into account flexural

The specific features of the proposed force-based formulation derived in the companion paper, which is applied for the first time to higher-order beam theories, are herein thoroughly validated. Introductory numerical examples illustrate the influence of mesh refinement, boundary conditions, and slenderness ratios for isotropic linear elastic response. Specific higher-order effects

An accurate assessment of the airflow in naturally ventilated double skin facades (DSF) is crucial for a correct design and performance evaluation. Measuring and predicting DSF airflow is not a straightforward task, given the stochastic nature of the wind, which can assist or oppose the buoyancy force. The present paper resumes the results of airflow measurements inside a naturally ventilated double skin facade using a tracer gas technique. The tests were performed on an outdoor air curtain (OAC) DSF test cell with a movable slat venetian blind. Measurements with no active shading and at night were also performed. Outdoor and test cell air gap temperatures were continuously measured and wind pressure coefficients were determined from wind tunnel tests. Experimental results were then compared to those obtained by a simple model taking into account both thermal and wind effects on the facade. From this comparison discharge coefficients were estimated, which can be used for characterizing the DSF behaviour.

The existing building stock in Azores islands (Portugal) was severely damaged during 1980and 1998 earthquakes. Structural failure was probably caused by a combination of factorsthat are not yet well understood. Earthquake source characteristics, site effects and structuralvulnerability may be some of those factors. However, it is very difficult to assess theinfluence of each factor on structural failure, mainly because recorded accelerograms usedin nonlinear structural analysis are influenced by both source characteristics and site conditions.The only way to overcome this problem is to control each factor individually whichcan be done by using simulated accelerograms. In our previous work, stochastic groundmotion simulations results were compared with earthquake records. Results seem to indicatethat simulated accelerograms can match recorded accelerograms if proper sourcecharacteristics and geological site conditions are selected. In this work, simulated accelerogramswere used for seismic nonlinear structural analysis. Simulations were carried outconsidering several 1980 Azores earthquake possible sources and for different geologicalsite conditions. Simulated accelerograms were then used to evaluate the structural nonlinearbehaviour of a reinforced concrete structure and of two masonry structures. The resultsof this work highlight the importance of site conditions and earthquake source characteristicsto the determination of the design seismic actions of Azores islands. This work wasperformed in the scope of

O Laboratório Nacional de Engenharia Civil tem uma longa experiência na área da Engenharia Sísmica, sendo uma das instituições de referência, a nível europeu, em todos os campos desta área das Ciências da Engenharia. A investigação europeia em Engenharia Sísmica teve início no final da década de 50, tendo sido o LNEC, na pessoa do Engenheiro Júlio Ferry Borges, o seu principal impulsionador. Desde então, assistiu-se ao estudo dos diferentes aspetos da fenomenologia ligada à caraterização da ação sísmica e ao comportamento das estruturas sujeitas à ação dos sismos, como ilustrado pelas cerca de 50 teses de mestrado e doutoramento nos diferentes domínios da Engenharia Sísmica, desenvolvidas no Núcleo de Engenharia Sísmica e Dinâmica de Estruturas (NESDE), nas duas ultimas décadas, e por mais de uma centena de investigadores visitantes, nacionais e estrangeiros. No âmbito da avaliação do risco sísmico, o LNEC tem tido um papel fundamental a nível nacional, assumindo a liderança da investigação científica nas matérias relacionadas com a perigosidade sísmica, a caraterização da ação sísmica, a avaliação do risco, e o desenvolvimento de estratégias para redução da vulnerabilidade sísmica...

This paper aims to assess and improve the seismic performance of an existing masonry building withflexible floors, representative of a Portuguese building typology

Earthquake scenarios are used in different activity domains like: civil protection disaster preparedness, computing overall seismic losses for a portfolio, or evaluating time histories and ground motion duration to be used in seismic design. However, the choice of an earthquake scenario is often based on deterministic arbitrary assumptions, like the region worst historical event reported. The purpose of this work is to overcome the disadvantages of a deterministic approach, in what concerns the choice of earthquake scenarios in Portugal. For each of the 278 Portuguese counties, a scenario ground motion based on a probabilistic seismic hazard disaggregation analysis is evaluated. Portuguese probabilistic seismic hazard analysis is reviewed in order to perform its disaggregation. Probabilistic seismic hazard was disaggregated considering different spaces of random variables. Bivariate conditional hazard distributions in X-Y (seismic source latitude and longitude) are analyzed, as well as multivariate conditional hazard distributions in M-R-

This paper describes and analyses the results of the seismic tests preformed at LNEC in a RC precast structure which is representative of a Portuguese system. This type of precast construction is used mainly for industrial buildings and was designed and constructed by a precast company with their common practice. The precast system can be considered as jointed with dry connections of limited ductility. A scaled 1/3 specimen was tested on LNEC

With the purpose of assessing the seismic behaviour of a reinforced concrete building structure non-seismically designed, an experimental study was carried out at the LNEC/Lisbon shake table, within the framework of the European project SPEAR. The tested structure was a simplification of a 3-storey building, irregular in plan, representative of older construction in southern Europe, without engineered earthquake resistance. It was designed for gravity loads alone, using the concrete design code used in Greece between 1954 and 1995, with construction practice and materials commonly used in southern Europe in the early 70

This paper describes the shaking table tests of an asymmetric limestone masonry building, under different reinforcement conditions. The work was performed in the aim of the project

The paper presents an experimental program on a 5 storey structural wall physical model performed in LNEC 3D shaking table, in Lisbon, within the Project ECOLEADER-LIS. The characteristics of the reduced model and the test set-up are described, as well as the analysis of the main experimental results. Furthermore the results of numerical simulations are discussed. These tests had the main purpose of studying and evaluating the seismic resistance of thin lightly reinforced structural walls representative of the Central Europe practice. Particular issues have been adressed: (a) To investigate the influence of simultaneous 3D loading conditions. (b) To study walls with T (H) cross-sections. (c) To investigate the free edge of a T (H) shaped walls in compression and different trypes of confinement. (d) To investigate the behaviour of coupled walls and the behaviour of diagonally reinforced coupling beams in thin walls. (e) To calibrate and further develop numerical models. Inelastic dynamic analysis was also performed using Multiple-Vertical-Line-Element-Model (MVLEM), which was extended into 3D and implemented into OpenSees. This macro model proved the ability to simulate and predict the global behavior of the wall as well as the behavior of confined boundary areas and local extensions of longitudinal reinforcement. Considerable overstrength was observed in the wall with minimum reinforcement. However, its deformation capacity was limited to less than 1% of the height. Relatively thick slab enhanced the strength of thin coupling beams considerably. Consequently, they did not perform as expected in capacity design and high axial forces as well as shear failure were induced into the wall piers. The EC8 confining reinforcement proved to be efficient. Simpler details (i.e. U-shaped stirrups) might be acceptable for low walls (5-storey) and/or in the case of low seismic intensity. Sequence of loading and pre-cracking influenced the response considerably. The influence of bi-axial loading was relatively low.

In the process of preservation of ancient masonry structures, damage evaluation and monitoring procedures are particularly attractive, due to the modern context of minimum repair and observational methods, with iterative and step-by-step approaches. High-priority research issues related to damage assessment and monitoring are global non-contact inspection techniques, sensor technology, data management, diagnostics (decision making and simulation), dynamic (modal) analysis, self-diagnosing / self-healing materials, and prediction of early degradation. On these concerns, the present paper aims to assess damage in masonry structures at an early stage. Replicates of historical constructions were built in virgin state. Afterwards, progressive damage was applied and modal identification analysis was performed at each damage stage, aiming at finding adequate correspondence between dynamic behavior and internal crack growth. Accelerations and dynamic strains were recorded in many points of the replicates. Comparisons between different techniques based on vibrations measurements are made to evaluate different damage identification methods.

This work uses a non-stationary stochastic seismological model, based on random vibration theory, for calculating response spectra and synthesizing strong ground motion acceleration records for Portugal Mainland. The validation of the method and comparison with strong ground motion records for Portugal are entirely carried out in terms of 5% damped pseudo absolute response spectra for acceleration. The calibrated model is used to simulate ground motion acceleration for the 1755 Lisbon earthquake. Five potential source rupture models that have been recently proposed by several authors for the 1755 Lisbon earthquake are tested: two analytical models based on hydrodynamic studies; two models based on seismic surveys and on from a recent suggestion based on induced stress changes.For all models, peak ground acceleration maps are compared with iso-intensities map of the earthquake in order to test the ability of the source models for estimating the intensities of the earthquake. The peak ground motion is calculated for different unknown parameters like the rupture velocity, the slip distribution and the nucleation point. The fault parameters like dimension, dip and strike are the ones proposed by the authors of the different analysed source models

This paper presents a dynamic identification analysis of a masonry construction, built to be tested in

In the framework of the ongoing European project

En este trabajo se confirma experimentalmente una nueva formulación del problema de los bloques rígidos sometidos a vibraciones externas. Un estudio sistemático de las respuestas del sistema permite determinar los valores de los parámetros relevantes. La nueva formulación hace más sencilla la implementación de técnicas computacionales para el problema da varios tipos de mecanismos acoplados. En las respuestas analizadas, tanto para régimen libre como forzado, se ha observado un buen acuerdo entre teoría y experimento.

This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe

The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.

The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies

Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.

In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.

O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.

Within the realm of natural hazards, geohazards are recognised as being particularly complex and often having the potential of triggering disasters. This complexity has led to increased political commitment and interest in engaging multi-stakeholder and citizens in disaster risk management. The AGEO project explored new forms to foster collaboration between civil society and authorities, using the rapidly developing field of citizen science and its innovative tool of citizens

Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107

Most of the Lisbon 18th century timber-framed masonry

Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.

When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko

A non

N/A

This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM

Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte

Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.

O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação

O Laboratório Nacional de Engenharia Civil (LNEC) participa atualmente numa das sete Tarefas, doprojeto Europeu SHARE- Seismic Hazard Harmonization in Europe, mais precisamente na tarefa nº 2,intitulada Requisitos de engenharia e aplicações.O presente relatório de progresso descreve a participação do LNEC na sub-tarefa 2.5 - Cenários derisco sísmico para cidades Europeias selecionadas

N/A

No presente relatório pretendem-se apresentar e definir alguns das linhasorientadoras para a simulação do comportamento dinâmico de fluidos no interior deAmortecedores de Líquido Sintonizado (TLDs), de acordo com o proposto na literatura.O problema da modelação do comportamento de fluidos no interior deAmortecedores de Líquido Sintonizado, à semelhança do que acontece parareservatórios, é complexo, sendo apresentados os principais modelos matemáticos emecânicos utilizados na actualidade.Assim serão descritos modelos de comportamento adoptados no casoparticular dos Amortecedores de Líquido Sintonizado (TLDs) e modelos simplificadosde sistemas de 1 (SDOF) ou mais graus (MDOF) de liberdade com com os referidosdispositivos de mitigação de acções dinâmicas acopladosO presente relatório servirá, à semelhança dos relatórios Sistemas passivos,activos, híbridos e semi-activos: Estado dos conhecimentos, Actividade experimentalna área dos sistemas passivos para a protecção sísmica de estruturas: Experiência doNESDE e Modelos de comportamento dinâmico para fluidos no interior dereservatórios como uma das linhas orientadoras para o desenvolvimento dos trabalhospropostos no âmbito do PIP 2009-2012 do NESDE-DE Protecção Sísmica deEstruturas: Reabilitação, reforço e sistemas inteligentes.

N/A

N/A

N/A

This Report corresponds to Task 2 of the NEFOREEE (New Fields of Research inEarthquake Engineering Experimentation) Project and comprises the description of theLNEC triaxial seismic platform and a presentation of the experimental programdeveloped in the scope of this Project.It is presented a description of the facility and the 3D seismic table with graphicalsupport, drawings of sizing and photographs, as well as its control system. The maininstrumentation available at the NESDE laboratory and used for this test is alsoincluded in this report.The model tested is described as well as the sequence of tests and the correspondingobtained results. Finally a brief analysis of the results is made.

O presente relatório final do projecto USuET integra o trabalho já apresentado norelatório de progresso de Sousa & Afonso [2007], nomeadamente no que toca aoscapítulos 2, 3 e parte do capítulo 4 e, adicionalmente, descreve, em detalhe, asactividades desenvolvidas no projecto desde a data desse relatório (secção 4.2, ecapítulos 5 e 6). A parte da investigação conducente à actualização do Simulador deCenários Sísmicos para ambiente WebSIG, aplicado ao Arquipélago dos Açores, não seencontra descrita com o mesmo detalhe, neste relatório, pois enquadra-se na tese demestrado em Sistemas de Informação Geográfica de Afonso [2007], submetida àUniversidade Técnica de Lisboa. A versão definitiva desta tese, cuja discussão se prevêainda em 2008, será enviada oportunamente.

N/A

This report describes the second phase activity of the Portuguese group in the Precast Structures EC8 research project. The Portuguese group is composed by Laboratório Nacional de Engenharia Civil (LNEC) and the Civibral, S.A. precast company. This phase follows the shaking table tests of a 2 stories structure of the same precast system, which is commercialized by Civibral. More information about these tests can be found in the repor.The goal of the work presented in this document is to assess the seismic behaviour of column-foundation and beam-column connections from the same precast system. To help achieve this goal, 4 column-foundation and 10 beam-column connections were tested using quasi-static, monotonic and cyclic tests, which were made imposing displacements to the specimens. The column-foundation connections (CFC) can be categorized as socket connections and the beam-column connections (BCC) as dry connections using only mechanical devices to transmit forces between elements. All the specimens were supplied and mounted by Civibral personal.

Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.

Análise da forma das edificações nas ações do vento

As condicionantes arquitetónicas e de urbanização na ventilação natural

Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento