Publications

In the early nineties, the Performance-Based Seismic Engineering (PBSE) principles have been introduced in the seismic design of structures. Several authors have identified the limitations of traditional force-based design (FBD) procedures widespread in most of the design codes to accomplish the PBSE requirements. Therefore, various contributions were made towards the development of displacement-based seismic design methodologies, in particularly the one proposed by Priestley, known as "Direct Displacement-Based Design" (DDBD). The purpose of this work is to investigate the DDBD approach in its entirety. In particular, the emphasis is set herein on the definition of the equivalent viscous damping and on the concrete impact of choosing one or another expression. Then, the efficiency of applying DDBD to reinforced concrete (RC) plane frames and dual frame-wall structures is assessed and the consequences of using the linear response spectrum suggested in the Eurocode 8 as input data is investigated.

A ventilação natural é uma eficiente estratégia para o condicionamento térmico passivo de edificações, e muitas vezes o seu potencial está relacionado às decisões em projeto diferentes do modelo convencional. Um exemplo são os sheds, aberturas na cobertura que funcionam como captadores ou extratores de ar, dependendo de sua localização em relação aos ventos dominantes. O objetivo do artigo é avaliar a influência do número de sheds e da distância entre eles no desempenho da ventilação natural. Os ângulos de incidência dos ventos analisados foram 0º, 45º, 135º e 180º. A metodologia adotada foi simulação por Dinâmica dos Fluidos Computacional (CFD), utilizando o software CFX. Os resultados indicam que o aumento do número de sheds reduz a renovação de ar interna para as situações de extração e captação de ar. Por outro lado, o aumento da distância entre esses dispositivos, incrementa o fluxo de ar interno para os sheds captadores. No entanto, teve-se uma redução na renovação de ar para os sheds extratores de ar. Isso ocorre pela redução da área total das abertiras de saída de ar, que apresenta uma influência na vazão volumétrica do edifício. Nos sheds captadores de ar o incremento ocorre, pois, apesar do aumento da distância ter reduzido o número das aberturas de entrada de ar, torna os sheds mais efetivos para captar o fluxo de ar.

The paper addresses the seismic vulnerability assessment of a multispan footbridge, prone to span unseating due to shorter seat lengths. The structure is representative of a series of pedestrian crossings located in the Southern part of Portugal, a region with a relevant seismicity. A probabilistic approach allows considering the variability of the seismic action and uncertainties in the definition of the material properties and/or structural behavior. Based on incremental dynamic analyses and corresponding fragility curves, it is shown that, for code compliance design acceleration, there is a significant probability that the structure will only suffer minor damage.

The paper addresses the seismic vulnerability assessment of a multi-span footbridge, prone to span unseating due to shorter seat lengths. The structure is representative of a series of pedestrian crossings located in the Southern part of Portugal, a region with a relevant seismicity. A probabilistic approach allows considering the variability of the seismic action and uncertainties in the definition of the material properties and/or structural behavior. Based on incremental dynamic analyses and corresponding fragility curves, it is shown that, for code compliance design acceleration, there is a significant probability that the structure will only suffer minor damage.

Distributed plasticity Euler-Bernoulli fiber beams are regularly used byresearchers and practitioners to simulate the nonlinear seismic responseof reinforced concrete framed structures. This study presents a sensitivityanalysis, combining newly proposed and existing goodness-of-fitmeasures, to identify commonly used engineering modeling optionsthat most critically influence the response accuracy. The dynamic behaviorof three distinct structures tested in international blind predictionchallenges is considered. Sensitivity parameters include equivalent viscousdamping, element formulation, strain penetration effects, andmaterial models. The results are critically discussed in light of theoreticalshortcomings of the model assumptions.

The solar chimney is a stack-induced ventilation strategy used to improve thermal performance in buildings. Besides operating via a buoyancy-driven airflow, even low velocity winds can affect the chimney functioning in both positive and negative ways. In technical literature, though, few studies have considered the influence of windspeed and direction, as well as discharge coefficients and wind pressure coefficients. This paper investigates the effects of wind interference on a solar chimney performance, through different scenarios of wind speed and direction, over a base case model. Wind tunnel experiments and computer simulations using EnergyPlus were carried out to perform qualitative and quantitative analyses of the airflow, as a function of the combined effect of thermal and wind components. Results showed that the airflow rate and distribution pattern at the outlet openings of the solar chimney are influenced by either the thermal gradients and, mainly, by the outdoor windvelocity and direction. A significant reduction in the volumetric flow rate of the chimney is observed due to wind incidence opposite to the inlet opening, even at low velocities, such as 0.6 m/s.

Uma parte significativa do edificado em Portugal não foi dimensionada para resistir a ações sísmicas. Como tal, o recente impulso do sector da reabilitação pode representar uma oportunidade única para promover a redução da vulnerabilidade sísmica dos edifícios existentes. Neste contexto, o presente trabalho apresenta uma metodologia para avaliar a vulnerabilidade sísmica duma classe de edifícios de betão armado que permite estabelecer indicadores simplificados do seu desempenho estrutural expectável. A metodologia proposta baseia-se num estudo numérico detalhado do comportamento sísmico de edifícios de betão armado com características representativas duma parte significativa do edificado deste tipo em Portugal, simulando de forma adequada os principais aspetos da sua resposta estrutural. Os resultados obtidos pela metodologia desenvolvida permitem identificar as principais vulnerabilidades do edificado e quantificar indicadores de desempenho estrutural que permitem avaliar de forma expedita a sua segurança estrutural.

A arquitetura recorre, por vezes, a dispositivos de sombreamento de grandes dimensões, com formas e configurações de montagem cuja resposta à ação do vento carece de caracterização. Este facto condiciona o correto dimensionamento dos apoios e, em menor escala, a determinação do próprio material de construção dos dispositivos.As dimensões dos elementos constituintes destes dispositivos dificultam o recurso a ensaios com modelos reduzidos pelo que se recorreu a um modelo seccional do dispositivo à escala real, sujeito ao escoamento proveniente de um túnel de vento de jacto livre. As características específicas deste ensaio, nomeadamente a geometria do perfil de sombreamento e respetivos suportes, gama de forças e a necessidade de minimizar a obstrução adicionada pela instrumentação ao escoamento, ditaram o desenvolvimento de uma solução particular para a medição das forças aerodinâmicas.O ensaio permitiu avaliar as cargas induzidas pelo escoamento para vários ângulos de incidência fazendo variar a inclinação do modelo relativamente ao jacto através de um suporte articulado onde se montou o modelo seccional, permitindo assim caracterizar o desempenho aerodinâmico do perfil na aplicação em estudo.

This paper describes the development process and initial tests performed with a new energy dissipation damper based on Shape Memory Alloy (SMA) wires. The aim of this study was to develop a new iteration of this type of devices, and eventually develop a methodology to properly design them for any type of application. The underlying concept of our device is the use of a double counteracting system of pre-strained SMA wire sections as the dissipating component. By using pre-strained wires, this design focuses on maximizing energy dissipation, partially relinquishing the re-centering capabilities of the device.The experimental part was performed on a downscaled prototype based on this design methodology. The goal of this study was to validate the basic mechanical concepts. The device was subjected to a considerable number of load cycling tests, in order to better characterize the SMA wire behavior when used in this arrangement and to improve our understanding of their influence on the device's capabilities.

In the frame of the UPStrat-MAFA

Apresenta-se uma abordagem para a avaliação de vulnerabilidade de estruturas com base em resultados experimentais obtidos em ensaios sísmicos, num contexto de análise de fragilidade para avaliação do risco sísmico. É proposta uma metodologia para obtenção da vulnerabilidade experimental de modelos ensaiados para níveis crescentes de excitação, e estimar a fragilidade com base em ensaios sísmicos.

Nesta comunicação apresenta-se um estudo de caracterização dinâmica da Ponte Miguel Torga com base em ensaios dinâmicos in-situ. Estes ensaios foram efetuados antes da abertura da ponte ao tráfego tendo consistido na medição das vibrações induzidas pelo tráfego de camiões carregados. Descrevem-se as técnicas de análise dos registos de aceleração, apresentando-se as características dinâmicas da ponte identificadas a partir dessa análise.

Desde a publicação em 1993 do regulamento português (RSA), onde são definidas as zonas sísmicas para o território e a respetiva ação, têm sido efetuados diversos estudos sobre casualidade e movimentos sísmicos intensos. É objetivo desta comunicação apresentar estudos recentes nesta matéria e os problemas encontrados com a aplicação do Eurocódigo 8 (EC-8), parte 1-1, para se dar inicio a uma oportuna revisão da regulamentação em vigor.

Apresenta-se a proposta para o Documento nacional de Aplicação (DNA) elaborado de acordo com o disposto na Pré-Norma Europeia ENV 1998-1-1:1994, Eurocódigo 8

Às 05h19m TUC do dia 9 de Julho de 1998 as ilhas do Grupo Central do Arquipélago dos Açores foram sacudidas por um forte sismo de magnitude md

The knowledge of the actual dynamic properties (natural frequencies, mode shapes and damping ratios) of bridge structures is extremely important to study the behavior of those structures in relation to seismic, wind or even traffic loads. Furthermore, the experimentally determined dynamic properties of a structure are an effective way to characterize its actual global behavior since they depend on its stiffness and mass distribution. The experimental modal analysis of bridges can be performed from the results of ambient vibration tests carried out on those civil engineering structures, with some advantages in relation to other types of in-situ dynamic tests. Ambient vibration tests have been recently conducted on two main bridges of the Portuguese roads network, a concrete arch bridge and a cable-stayed bridge. The tests carried out on the two bridges, the analysis techniques and the main results that were obtained are presented in this paper.

This paper reports an experimental study aiming at the analysis of the behavior under horizontal actions of reinforced concrete frames infilled with different brick masonry walls, conducted at the Centre for studies and Equipment in Earthquake Engineering (C3ES) of the national Laboratory for Civil Engineering of Portugal (LNEC).Nine models, in a scale 2:3, were tested, named: two bare frames, four fully infilled frames and three infilled frames with a window opening. Two different horizontal histories of displacements under identical velocities were imposed at the level of the beam centerline: cyclic (six models) and monotonic (three models). Constant vertical forces were applied at the top of the columns in order to reproduce the effect of the upper floors of a building. The characteristics of the models, the test set-up and instrumentation and the testing procedure are reported. Some results of this experimental study are also presented and analysed.

This paper reports part of an experimental work conducted at LNEC/C3ES (Centre for Studies and Equipments in Earthquake Engineering) aiming at analyzing the behavior of R/C bare and infilled frames subjected to horizontal loads and the effectiveness of different repair procedures. Three models in a 2:3 scale were tested. One of these models was only a bare R/C frame and the other two were R/C frames fully infilled with brick masonry. In a first phase the models were tested under horizontal cyclic actions that caused severe damage in the infill walls and also some damage in the R/C frames. In a second phase the models were repaired and subjected again to horizontal cyclic actions. Different repair techniques were used for the two infilled models. The assessment of the models behavior, before and after repair, is presented in terms of strength, stiffness degradation, energy dissipation and failure mechanisms.

The object of this paper is to improve the probabilistic methodology to evaluate seismic losses in a given area, considering the randomness of the buildings vulnerability. Probabilistic methods for the evaluation of seismic losses are used taking into account both (i) the seismic hazard in the area and (ii) the seismic vulnerability of the existing stock of buildings. The distribution of losses is obtained convolving the probability distribution of seismic hazard (Beta distribution) with the conditional probability distribution of vulnerability, given a macroseismic intensity (Lognormal distribution), for a known stock of buildings. The above-described methodology is applied to the Portuguese continental country. The number of housing units per county as a function of the epoch of construction, available from the Portuguese Census 91 is the data base for the application of the model.

This paper presents an experimental study on the behaviour of reinforced concrete infilled frames, carried out at the shaking table of the Centre for Earthquake Studies of LNEC, in Lisbon, within the 2nd phase of the European Programme ECOEST II, by request of the University of Patras. Five three-dimensional structures were tested, at real scale, with one storey and one bay in each of the two orthogonal directions of the horizontal plan. A biaxial seismic excitation was considered based on the adaptation of the records of two orthogonal horizontal components of the Patras 1993 earthquake, taking into account the inertial characteristics of the shaking table. The tests carried out are summarised, describing the test set-up and instrumentation, as well as the methodology used. The experimental results obtained are outlined and analysed.

This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe

The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.

The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies

Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.

In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.

O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.

Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107

Most of the Lisbon 18th century timber-framed masonry

Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.

When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko

A non

N/A

This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM

Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte

Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.

O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação

A caracterização da ação sísmica, para efeitos de projeto e verificação de segurança das estruturas de engenharia civil, é realizada para valores de intensidade sísmica elevados quando comparados com os valores de intensidade sísmica sentidos frequentemente. Tais valores elevados são compatíveis com os níveis de segurança exigidos para as estruturas, que usualmente são considerados implícitos nas regras de dimensionamento e verificação de segurança de estruturas contempladas nos códigos em vigor.

O presente relatório, elaborado no âmbito do projecto de investigação para a Fundação para a Ciência e a Tecnologia intitulado

Os sismos são fenómenos naturais que apenas poderão ter consequências desastrosas se afetarem uma região habitada do globo. Sem dúvida que os piores efeitos de um desastre sísmico são as perdas de vida humana envolvidas.A redução das perdas de vidas humanas é assim um dos grandes objetivos das políticas de prevenção e proteção sísmica e do domínio de investigação da engenharia sísmica.Para se ter uma ideia da dimensão do problema refira-se que apenas no século XX (entre 1900 e o fim de 1992), o montante oficial de vítimas mortais em 1 100 sismos muito severos, atingiu o total de 1 528 000. Perto de metade deste número de vítimas ocorreu num único país, a China, e as principais contribuições para este.

O presente relatório, elaborado no âmbito do projeto de investigação PRAXIS XXI

O presente relatório, elaborado no âmbito do projeto de investigação para a Fundação para a Ciência e a Tecnologia intitulado

The present progress report describes the research developed by LNEC under the ENVIRONMENT project ENV4-CT97-0548, entitled

O presente estudo tem por objetivo apresentar uma metodologia para a avaliação dos efeitos da propagação das ondas sísmicas em condutas de água enterradas. Essa avaliação é efetuada em termos do campo de deformações (extensões axiais e curvaturas), a serem impostas nas condutas, para diferentes valores máximos de aceleração e velocidade da ação sísmica associados a diferentes períodos de retorno.A metodologia desenvolvida é aplicada à cidade de Lisboa considerando as características locais do terreno, diversos diâmetros de tubagens e ambas as situações de condutas contínuas ou com juntas.

As part of ECOEST European research activities, this report describes the experimental programme carried out at the new LNEC seismic simulator facility. It is reported a detailed characterization of the frequency response of the shaking table and the results from an assessment of its control fidelity. This information will act as a benchmark, against which the performance of future tests at this facility could be gauged.A part of the description of the procedures and results of the test programme carried out, it was also compiled descriptive material about the entire facility.

O presente relatório descreve os estudos efetuados no LNEC, que visaram o desenvolvimento e implementação computacional de um algoritmo representativo das relações histeréticas forças-deslocamentos generalizados observados em ensaios de elementos de betão armado sujeitos á flexão.Foi dado um carater geral à implementação do modelo, de forma a poder ser usado em trabalhos futuros de análise dinâmica em regime não linear de estruturas de betão armado, sujeitas á ação dos sismos.O algoritmo computacional resultante é suficientemente versátil uma vez que através da introdução de alguns parâmetros pode reproduzir diferentes comportamentos estruturais, tais como: degradação de rigidez e resistência, efeito de

Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.

Análise da forma das edificações nas ações do vento

As condicionantes arquitetónicas e de urbanização na ventilação natural

Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento