Publications

A ventilação natural é uma eficiente estratégia projetual para ocondicionamento térmico passivo de edificações, ocorrendo por açãodos ventos, efeito chaminé ou pela combinação de ambos. Dentre asestratégias de ventilação, destacam-se os sheds, aberturas no telhado,que funcionam como captadores ou extratores de ar, dependendo de sualocalização em relação aos ventos dominantes. O objetivo desse artigo é avaliar ainfluência da variação na geometria dos sheds e na dimensão das aberturas deentrada e saída de ar no desempenho da ventilação natural. O sistema foi avaliadopara os ângulos de incidência dos ventos externos de 0° e 45° (extração) e 135° e180° (captação). A metodologia adotada foi a simulação por Dinâmica dos FluídosComputacional (CFD), utilizando como ferramenta o software CFX. Foramrealizadas análises quantitativas (taxas de renovação de ar/hora e coeficiente depressão nas aberturas) e qualitativas (planos de contorno e vetores de direção eintensidade do fluxo de ar). Os resultados indicam que sheds com geometriasaerodinâmicas e o aumento das aberturas de saída de ar incrementam o fluxo de arinterno. Para os sheds captadores o aumento isolado das aberturas de entrada de arnão proporciona uma melhora significativa na captação dos ventos pela cobertura.

The analysis of the shaking table test of a 3-wall stone masonry structure performed with a discrete element model is presented. The numerical model, created with the code 3DEC, employed a rigid block representation and a Mohr-Coulomb joint model. Joint stiffness calibration to match the experimental natural frequencies is discussed, as well as the boundary conditions to simulate the shake table. Comparisons are made with the measured displacements at key locations, and the modes of deformation and fracture of the walls. The DEM model was able to reproduce important features of the shaking table tests. The experimental deformation and near collapse patterns were clearly identifiable in the numerical simulations, which produced displacements within the observed orders of magnitude, for the various levels of excitation.

Strong ground motion prediction based on finite-fault simulation requires the identification of the fault (strike, dip, length and width), source kinematics parameters (stress drop, rupture velocity and slip distribution), regional crustal properties (geometrical spreading, anelastic structure, and upper crustal amplification and attenuation parameters) and the determination of amplification effects due to the local site geology. The general purpose of this study is to understand source and attenuation properties in the Azores, by the determination of stress drop, quality factor and kappa, through records obtained by the Portuguese digital seismic and accelerometer network. Source Spectra were obtained, for each record, after correcting observed spectra from geometrical spreading and anelastic attenuation effect: quality factor was estimated based on coda decay in the time domain and the kappa parameter was estimated by fitting the high-frequency decay of the acceleration spectrum with a straight line in a log-linear scale. Mean stress drop value was obtained considering that

The assessment of wind energy resource for the development of deep offshore wind plants requires the use of every possible source of data and, in many cases, includes data gathered at meteorological stations installed at islands, islets or even oil platforms - all structures that interfere with, and change, the flow characteristics. This work aims to contribute to the evaluation of such changes in the flow by developing a correction methodology and applying it to the case of Berlenga island, Portugal. The study is performed using computational fluid dynamic simulations validated by wind tunnel tests. In order to simulate the incoming offshore flow with CFD models a wind profile, unknown a priori, was established using observations from two coastal wind stations and a power law wind profile was fitted to the existing data (alfa=0.165). The results show that the resulting horizontal wind speed at 80 m above sea level is 16% lower than the wind speed at 80 m above the island for the dominant wind direction sector.

An innovative higher-order beam theory, capable of accurately taking into account flexural

The specific features of the proposed force-based formulation derived in the companion paper, which is applied for the first time to higher-order beam theories, are herein thoroughly validated. Introductory numerical examples illustrate the influence of mesh refinement, boundary conditions, and slenderness ratios for isotropic linear elastic response. Specific higher-order effects

An accurate assessment of the airflow in naturally ventilated double skin facades (DSF) is crucial for a correct design and performance evaluation. Measuring and predicting DSF airflow is not a straightforward task, given the stochastic nature of the wind, which can assist or oppose the buoyancy force. The present paper resumes the results of airflow measurements inside a naturally ventilated double skin facade using a tracer gas technique. The tests were performed on an outdoor air curtain (OAC) DSF test cell with a movable slat venetian blind. Measurements with no active shading and at night were also performed. Outdoor and test cell air gap temperatures were continuously measured and wind pressure coefficients were determined from wind tunnel tests. Experimental results were then compared to those obtained by a simple model taking into account both thermal and wind effects on the facade. From this comparison discharge coefficients were estimated, which can be used for characterizing the DSF behaviour.

The existing building stock in Azores islands (Portugal) was severely damaged during 1980and 1998 earthquakes. Structural failure was probably caused by a combination of factorsthat are not yet well understood. Earthquake source characteristics, site effects and structuralvulnerability may be some of those factors. However, it is very difficult to assess theinfluence of each factor on structural failure, mainly because recorded accelerograms usedin nonlinear structural analysis are influenced by both source characteristics and site conditions.The only way to overcome this problem is to control each factor individually whichcan be done by using simulated accelerograms. In our previous work, stochastic groundmotion simulations results were compared with earthquake records. Results seem to indicatethat simulated accelerograms can match recorded accelerograms if proper sourcecharacteristics and geological site conditions are selected. In this work, simulated accelerogramswere used for seismic nonlinear structural analysis. Simulations were carried outconsidering several 1980 Azores earthquake possible sources and for different geologicalsite conditions. Simulated accelerograms were then used to evaluate the structural nonlinearbehaviour of a reinforced concrete structure and of two masonry structures. The resultsof this work highlight the importance of site conditions and earthquake source characteristicsto the determination of the design seismic actions of Azores islands. This work wasperformed in the scope of

O Laboratório Nacional de Engenharia Civil tem uma longa experiência na área da Engenharia Sísmica, sendo uma das instituições de referência, a nível europeu, em todos os campos desta área das Ciências da Engenharia. A investigação europeia em Engenharia Sísmica teve início no final da década de 50, tendo sido o LNEC, na pessoa do Engenheiro Júlio Ferry Borges, o seu principal impulsionador. Desde então, assistiu-se ao estudo dos diferentes aspetos da fenomenologia ligada à caraterização da ação sísmica e ao comportamento das estruturas sujeitas à ação dos sismos, como ilustrado pelas cerca de 50 teses de mestrado e doutoramento nos diferentes domínios da Engenharia Sísmica, desenvolvidas no Núcleo de Engenharia Sísmica e Dinâmica de Estruturas (NESDE), nas duas ultimas décadas, e por mais de uma centena de investigadores visitantes, nacionais e estrangeiros. No âmbito da avaliação do risco sísmico, o LNEC tem tido um papel fundamental a nível nacional, assumindo a liderança da investigação científica nas matérias relacionadas com a perigosidade sísmica, a caraterização da ação sísmica, a avaliação do risco, e o desenvolvimento de estratégias para redução da vulnerabilidade sísmica...

This paper aims to assess and improve the seismic performance of an existing masonry building withflexible floors, representative of a Portuguese building typology

Catástrofes sísmicas recentes mostram a necessidade de estabelecer estratégias de mitigação do risco sísmico para regiões urbanas que possuam elevada perigosidade sísmica dirigidas, m especial, às construções que não cumpram as regras de dimensionamento sísmico recentes mas que possuam um valor cultural, ou função social importante, impedindo a sua demolição e substituição, no processo normal de renovação dos parques de estruturas construídos, por estruturas modernas sismoresistentes.

A utilização de dispositivos de dissipação de energia é vista como forma eficiente para proteger estruturas contra ações sísmicas. Recentemente, dispositivos do tipo Amortecedores de Líquido Sintonizados (ALS) têm despertado a atenção da comunidade científica como forma simples mas eficaz para reduzir a resposta de estruturas face a ações dinâmicas. Os ALSs são tanques, com relações entre comprimento e altura de água tais que permitem que a sua frequência se ajuste à frequência da estrutura cujos movimentos se pretende mitigar. A energia de vibração é transferida para a água em movimento onde se dissipa. Os princípios básicos de funcionamento são semelhantes aos observados para os Amortecedores de Massa Sintonizados (AMSs), com as vantagens da instalação e da manutenção serem muito mais fáceis e económicas. Este artigo descreve simulações numéricas sobre ALS, isolados e incluídos numa estrutura de transmissão de aproximadamente 4 toneladas, ensaiados experimentalmente. Para o efeito foi usado um software de acesso livre denominado CLAWPACK com potencialidades para simular os fenómenos não lineares que ocorrem no interior de ALSs sujeito a ações dinâmicas. O CLAWPACK consiste num conjunto de rotinas em Fortran desenvolvidas para obtenção de soluções numéricas de sistemas hiperbólicos de equações parcialmente diferenciais no tempo, como é o caso dos fenómenos não-lineares subjacentes à shallow water wave theory. Foram necessárias adaptações e ajustes em algumas das rotinas principais para permitir a simulação de excitações pretendidas. A descrição dos conceitos teóricos subjacentes às adaptações efetuadas são parte integrante de uma dissertação de Doutoramento. Nas simulações numéricas são variados alguns parâmetros principais dos ALSs, em que se incluem a altura de água, a amplitude de excitação e o número de dispositivos. Estes estudos paramétricos são importantes para a compreensão da influência de cada parâmetro na resposta do dispositivo e para alcançar a configuração ótima para cada sistema estrutural e Acão dinâmica imposta. Os principais resultados obtidos das simulações numéricas são comparados, para calibração, com os resultados obtidos de um programa experimental desenvolvido no âmbito de uma tese de Doutoramento, tanto para o ALS isolado como para um conjunto de ALS incluídos nas estruturas de transmissão ensaiadas. As principais conclusões obtidas serão também apresentadas.

A mitigação de danos em edifícios submetidos a ações sísmicas, tem vindo a ser alvo de importantes contribuições provenientes de diferentes áreas do conhecimento visando uma melhoria de eficiência das construções. Uma das vias em desenvolvimento passa pela utilização de sistemas de absorção de vibrações O presente artigo descreve um sistema de simulação do comportamento dinâmico de edifícios com frequências naturais entre 0,7 e 2,9 Hz destinado à realização de ensaios experimentais de validação de modelos teóricos e de avaliação do desempenho de sistemas de absorção de vibrações. Apresentam-se os resultados de ensaios experimentais realizados aos elementos elásticos do sistema e à totalidade do sistema com vista à sua caracterização e validação experimental.

Abstract. The application of discrete element models based on rigid block formulationsto the analysis of masonry walls under horizontal out-of-plane loading isdiscussed. The problems raised by the representation of an irregular fabric by asimplified block pattern are addressed. Two procedures for creating irregularblock systems are presented, one using Voronoi polygons, the other based on abed and cross joint structure with random deviations. A test problem provides acomparison of various regular and random block patterns, showing their influenceon the failure loads. The estimation of natural frequencies of rigid block models,and its application to static pushover analyses, is addressed. An example of applicationof a rigid block model to a wall capacity problem is presented.

The boundary conditions between the tested structures and the platform of a large shaking table are a major parameter for the design and numerical analyses of shaking table tests. A foremost attention is given to the design of the foundation and anchorage of the structure. All analyses are made considering a completely rigid shaking table: rigid actuators and rigid platform. However, since quite a long time, the shaking table / structure interaction has been clearly observed (Blondet and Esparza, 1988) when analysing the shaking table / actuators interaction, depending on the control tuning. In CEA Saclay, during the last 15 years, decreases of mock-up frequencies between calculations and experimental tests of massive structures have been observed: CASSBA, CAMUS 1 to 4, CAMUS 2000 (Combescure and Ragueneau, 2002) and more recently SMART. For a long time it has been calculated, after tests, the global stiffness that the

The collaborative research project ERSTA (Estudo do Risco Sísmico e de Tsunamis do Algarve), supported by ANPC (Autoridade Nacional de Protecção Civil), as given rise to a series of new developments, namely therevised seismic catalogue from IM (Instituto de Meteorologia) and the redrawing of new seismogenic zones affecting the Algarve region. It is therefore relevant to review the parameters of the Gutenberg-Richtermagnitude-frequency relation, intending to perform a future revision of the probabilistic seismic hazard analysisof the region and its disaggregation. The parameters of the Gutenberg-Richter magnitude-frequency relationships for the new seismogenic zones (IM, 2008) were estimated for unequal observation periods fordifferent magnitude ranges - determined through the analysis of the completeness of the seismic catalogue from IM - using the maximum likelihood method (Weichert, 1980).

Latest COVICOCEPAD developments

The paper contributes to an assessment of the uncertainties involved in the use of current loss modeling methodologies when applied to the estimation of building damage and casualty generation in urban areas. The work derives from studies conducted within the EU-funded LESSLOSS project with the aim of providing a basis for urban planning authorities methods to assess alternative mitigation strategies. Research teams in Istanbul, Thessaloniki and Lisbon developed methods applicable to their own city and building stock. A benchmarking study was then carried out to compare the results of the three approaches when applied to a standardized

This paper presents the results of shaking table tests performed on two full-scale masonry houses typical from North-European countries. The main objective of the study was to assess the seismic behavior of such houses for situations of low to moderate seismicity, as well as to evidence the efficiency of some reinforcing details. Themain outcomes are that the value of the behavior factor ("q") for unreinforced masonry and the value of the limitslenderness of masonry panels adjacent to openings proposed by Eurocode 8 are confirmed by the experimentalresults. Furthermore, the devices proposed to improve the seismic behavior are found efficient for limiting the damages in the range of seismicity level for which they are intended but have no impact on the global collapse limitstate.

Traditional design approaches usually consider seismic actions as equivalent static actions. Recent research has shown that adopting a dynamic approach where the real characteristics of seismic actions are taken into account may lead to reach significant behavior improvements. The inclusion of energy dissipation passive devices is nowadays seen as an effective way of improving structures protection towards seismic actions. A significant number of this kind of devices is already placed in real structures all over the world.Vibration mitigation of the seismic actions imposed to the structures is being more and more taken into account in structures design. In order to get more effective systems, structure

This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe

The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.

The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies

Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.

In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.

O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.

Within the realm of natural hazards, geohazards are recognised as being particularly complex and often having the potential of triggering disasters. This complexity has led to increased political commitment and interest in engaging multi-stakeholder and citizens in disaster risk management. The AGEO project explored new forms to foster collaboration between civil society and authorities, using the rapidly developing field of citizen science and its innovative tool of citizens

Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107

Most of the Lisbon 18th century timber-framed masonry

Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.

When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko

A non

N/A

This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM

Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte

Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.

O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação

N/A

This report addresses the National Laboratory for Civil Engineering (LNEC) participation in Subproject 10 Earthquake disaster scenario predictions and loss modelling for urban areas. More precisely this report was developed in order to accomplish the 24 months LESSLOSS deliverable nº 85, which achieves loss estimates for the Metropolitan Area of Lisbon (MAL), for pre-defined scenarios earthquake. These loss estimations represent the reference situation to be compared with revised loss estimates after implementing mitigation actions with the ultimate goal of being established, in the next deliverable, the

N/A

N/A

N/A

The present report describes the construction of a model in limestone masonry for the user Group 3 oh the ECOLEADER Project, led by IRIDEX Construction Group, and the first phase of the experimental program developed in LNEC. The description of the construction, a photographic report and the results obtained on the characteristics tests made on the mortars used in the construction are presented.The construction was carried out by contractor José dos Santos Paixão on the basics of model details and materials specifications proposed by the User group 3, being NESDE/LNEC responsible for the guidance and supervision of the works.

This report describes the first phase activity of the Portuguese group in the Precast Structures EC8 research projet. The Portuguese group is composed by Laboratório Nacional de Engenharia Civil (LNEC) and the Civibral, S.A. Precast Company.In this phase, seismic test were made in the LNEC

The present report addresses the first twelve months of LNEC participation in LESSLOSS

The dynamics of rigid bodies was studies by long time, because this phenomenon is important in the seismic security of some types of structures. However, there are few experimental studies. This job shows the experimental test carried out at the Laboratório Nacional de Engenharia Civil (LNEC) of Portugal. Four blue granites stones were tested, each one with different geometrical characteristics, under harmonic and random motions.A numerical simulation was carried out with the Discrete Element Method (DEM). This method has shown to be a good tool in the study of the dynamics of rigid bodies. It was proposed a new methodology to find the parameters of the DEM by using the parameters of classical theory.

The project LESSLOSS

Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.

Análise da forma das edificações nas ações do vento

As condicionantes arquitetónicas e de urbanização na ventilação natural

Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento