Papers
Info
Análise não linear de um conjunto de edifícios em placa no bairro de Alvalade: avaliação preliminar de estabilidade e previsão dos mecanismos de colapso
Os edifícios tipo
Year: 2019
Number Pages:
97-106pp.
Author(s): Bernardo, V.; Candeias, P.; Campos Costa, A.; Costa, A.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 11.
Keywords: Modos de colapso; Análise preliminar de estabilidade; Applied Element Method; Ensaios de caraterização dinâmica; Edifícios tipo
Info
Paredes resistentes de alvenaria de tijolo reforçadas com revestimentos armados
As construções antigas fazem parte do tecido histórico das cidades, pelo que é importante proceder a intervenções de reabilitação eficientes, mas não destruidoras da sua identidade e valor cultural intrínseco. No contexto do reforço sísmico, a utilização de rebocos armados apresenta-se como uma solução simples e pouco intrusiva. Os rebocos armados em paredes conferem um aumento da resistência e da ductilidade ao corte (no plano) e da ductilidade à flexão (fora do plano), um aumento da resistência superficial e permitem ainda um melhor controlo da fendilhação.Neste artigo será apresentada a caracterização experimental dos materiais constituintes das alvenarias (argamassas de assentamento, argamassas de revestimento e tijolos), e os resultados obtidos em ensaios de compressão diagonal de pequenos provetes de alvenaria, com e sem a aplicação de rebocos armados.
Year: 2019
Number Pages:
05-18pp.
Author(s): Mera Marques, A.; Candeias, P.; Ferreira, J.; Santos Silva, A.; Veiga, M. R.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 10.
Keywords: Rebocos armados; Ensaios de compressão diagonal; Paredes resistentes de alvenaria
Info
Two-way bending out-of-plane collapse of a full-scale URM building tested on a shake table
This paper describes a shake table test on a one-storey full-scale unreinforced masonry structure, which complements an earlier testing of a two-storey structure with similar characteristics. The building specimen was meant to represent the upper floors of the end-unit of a terraced house, built with cavity walls and without any particular seismic design or detailing. In these specimens, the masonry walls were composed of two leaves: a load-bearing inner one made of calcium silicate bricks sustaining a reinforced concrete floor and an external leaf made of clay-bricks connected to the inner leaf by means of metallic ties. A pitched timber roof was supported by two triangular gable walls. Floor acceleration response histories of the previously tested two-storey specimen were used as input motions. An incremental dynamic test, with vertical and horizontal inputs, was carried out up to the explicit collapse of some bearing elements of the structure. In particular, a two-way bending out-of-plane collapse of a load-bearing wall was observed and described.
Year: 2019
Number Pages:
2165
Author(s): Correia, A.A.; Candeias, P.; Campos Costa, A.; Tomassetti, U.; Graziotti, F.
: Bulletin of Earthquake Engineering
Editor: Springer
Volume:
Vol.17.
Keywords: Vertical acceleration; Non-structural components; Timber roof; Collapse; Out-of-plane; Shake table
Info
Wind tunnel and CFD analysis of wind-induced natural ventilation in sheds roof building: impact of alignment and distance between sheds
Sheds roof is a natural ventilation strategy that presents roof openings working as air collectors or extractors. A detailed review of the literature indicates a lack of research analyzing the impact of different sheds roof shapes and roof configurations on natural ventilation potential. his paper aims to evaluate the impact of changes in distance and alignment between wind catcher and leeward sheds roof. The methodology was Computational Fluid Dynamics (FCD) simulation. tests were performed in a atmospheric boundary layer wind tunnel on a 1:15 scale model to evaluate the accuracy of CFD simulations in different design configurations of sheds roof. The analysis showed that CFD simulations are generaly in good agreement with the wind tunnel tests. The difference between the most o the monitored points in the two tools used had errors below 10%. besides this, the results show that changes in alignment of the sheds and increasing distance between them decrease and increase the internal airflow to the leeward and windward sheds of the roof, respectively. In the first case it is due to the reduction in the sheds openings area. In the second these changes turn the sheds more effective in the air capture.
Year: 2019
Number Pages:
22p.
Author(s): Lukiantchuki, M.; Shimomura, A.; Marques da Silva, F.; Caram, R.
: International Journal of Ventilation
Editor: Taylor & Francis
Keywords: wind tunnel; CFD; Sheds roof; Natural Ventilation
Info
Análise da segurança de pontes sujeitas a ações dinâmicas durante a reabilitação dos pilares
Apresenta-se neste artigo um estudo de análise da segurança das pontes Criz II e de São João de Areias, na albufeira da barragem da Aguieira, em Portugal, durante a execução de novas fundações, no âmbito das empreitadas de reabilitação, na proximidade dos pilares afetados por reações expansivas do betão no seu embasamento. A ação dinâmica induzida pela perfuração de maciços rochosos foi modelada como uma ação periódica composta por um momento torsor aplicado na fundação de cada pilar isolado combinado com três forças ortogonais representando a força imposta pela caroteadora e os desequilíbrios das tensões de corte por rotação.Através da análise dinâmica linear das estruturas completas e de análises não lineares estáticas e dinâmicas dos pilares, foram estabelecidas as condicionantes às vibrações induzidas pelas máquinas caroteadoras, nomeadamente em termos de limites máximos da resposta em velocidade no topo dos embasamentos, edefinidas as condições de monitorização da estrutura durante a obra. Estas especificações foram elaboradas em estreita colaboração com técnicos da Infraestruturas de Portugal, I.P., e incluídas nas Cláusulas Técnicas Especiais para o lançamento da empreitada.
Year: 2018
Number Pages:
05-18pp.
Author(s): Campos Costa, A.; Candeias, P.; Lemos, J. V.; Catarino, J. M.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 8.
Keywords: Limites de vibração em embasamentos; Vibrações induzidas por caroteadoras; Análise de segurança de pontes
Info
Assessment of the combined in
Understanding the out
Year: 2018
Number Pages:
2821-2839pp.
Author(s): Correia, A.A.; Lourenço, P.; Onat, O.; Koçak, A.
: Earthquake Engineering and Structural Dynamics
Editor: Wiley
Volume:
47.
Keywords: Shake table experiment; Reinforced concrete; Out
Info
Characterization of reinforced timber masonry walls in
After the large destruction of Lisbon due to the 1755 earthquake, the city had to be completely rebuilt. The innovative
Year: 2018
Number Pages:
93-106 pp.
Author(s): Gonçalves, A.; Guerreiro, L.; Candeias, P.; Ferreira, J.; Campos Costa, A.
: Engineering Structures
Editor: Elsevier
Volume:
V. 166.
Keywords: Pombalino buildings; Seismic behavior; Dynamic tests; Timber masonry walls
Info
Characterization of reinforced timber masonry walls in
After the large destruction of Lisbon due to the 1755 earthquake, the city had to be completely rebuilt. The innovative
Year: 2018
Number Pages:
93-106pp.
Author(s): Gonçalves, A.; Guerreiro, L.; Candeias, P.; Ferreira, J.; Campos Costa, A.
: Engineering Structures
Editor: Elsevier
Volume:
Volume 166.
Keywords: Timber masonry walls;
Info
Characterization of timber masonry walls with dynamic tests
Timber-framed wall buildings are seen all over Europe, especially in seismic regions, given its adequacy to resist earthquakes. The
Year: 2018
Number Pages:
16p.
Author(s): Gonçalves, A.; Candeias, P.; Guerreiro, L.; Ferreira, J.; Campos Costa, A.
: International Journal of Architectural Heritage - Conservation, Analysis, and Restoration
Editor: Taylor&Francis
Volume:
Volume 12, 2018.
Keywords: Timber masonry walls; Shaking table; Resist earthquakes; Rehabilitation; Dynamic tests
Info
Characterization of timber masonry walls with dynamic tests
Timber-framed wall buildings are seen all over Europe, especially in seismic regions, given its adequacy to resist earthquakes. The
Year: 2018
Number Pages:
298-313pp.
Author(s): Gonçalves, A.; Candeias, P.; Ferreira, J.; Campos Costa, A.; Guerreiro, L.
: International Journal of Architectural Heritage
Editor: Taylor & Francis
Volume:
Vol.13.
Keywords: Timber masonry walls; Shaking table; Resist earthquakes; Dynamic tests; Rehabilitation
|
Comunicação
Info
Northridge earthquake of 17 January 1994: Observations from field trip by a portuguese group
A group of five Portuguese experts on earthquake engineering visited the Los Angeles region after the 17 January 1994 Northridge earthquake. The observations mad during the field trip are briefly reports. Discussion is made on the behaviour of different types of structures, namely, masonry, wooden, reinforced concrete and steel structures, as well as special structural typologies such as precast parking lots, tilt-ups and bridges. The presentation is illustrated by means of a few cases, for which the causes of malfunctioning were anticipated.Mention is also made to the behaviour of lifelines, such as electricity, gas and water supply, sewage systems and telephones. The damage assessment is viewed under the light of the ground motion severity.A description of the organizational aspects and procedures adopted for the inspection, immediate reinforcement, recovery and reconstruction of the main buildings, bridges and other utilities are also referred.
Year: 1994
Number Pages:
813-818pp.
Author(s): Oliveira, C.S.; Azevedo, J.; Delgado, R.M.; Costa, A.; Campos Costa, A.
Editor: A.A. Balkema
Volume:
Vol. 1.
Keywords: Northridge earthquake
Info
O novo simulador sísmico triaxial do LNEC
Esta comunicação apresenta a conceção, o projeto, a instalação e o planeamento da utilização durante os dois primeiros anos do simulador sísmico triaxial que brevemente começará a funcionar no LNEC. Este simulador destina-se ao ensaio dinâmico até á rotura de grandes modelos de edifícios e ponte (até 60t). Este simulador realiza uma conceção inovadora, que se traduz essencialmente pela eliminação dos 3 graus de liberdade de rotação através de 3 sistemas mecânicos constituídos por uma barra de torção, duas manivelas e duas bielas.
Year: 1994
Number Pages:
10p.
Author(s): Duarte, R.T.; Emílio, F. T.; Oliveira Costa, C.; Carvalhal, F.; Campos Costa, A.; Vaz, C.T.
Editor: FEUP
Keywords: Projeto; Mesa sísmica
Info
Optimal design of torsionally asymmetric buildings for hazard consistent reliability levels
The paper presents the results that permit the identification of optimal design methods for building structures in terms of a eccentricity and are calibrated for probability of failure, evaluated for critical scenarios of expected earthquake intensities.
Year: 1994
Number Pages:
1353-1358pp.
Author(s): Campos Costa, A.
Editor: A.A. Balkema
Volume:
Vol. 2.
Keywords: Hazard; Asymmetric buildings
Info
The new LNEC triaxial earthquake simulator
Some fundamental aspects concerning the overall conception and mechanical design of the new LNEC seismic shaking table, which will have three translational degrees of freedom, are presented. Considerations are made regarding its adaptive control, pointing out the interactions between the behaviour of the mechanical and control systems as far the overall performance of the seismic shaking table is concerned. Lastly, some considerations are also presented on the special building that houses the shaking table.
Year: 1994
Number Pages:
2999-3008pp.
Author(s): Duarte, R.T.; Campos Costa, A.; Vaz, C.T.
Editor: A.A. Balkema
Volume:
Vol. 4.
Keywords: Shaking table LNEC
Info
Analytical modelling of the hysteretic behaviour of RC frame structures infilled with masonry walls.
In this paper we an analytical model to study the hysteretic behavior, under cyclic loading, of RC frames infilled with masonry panels.The calibration of the parameters which define the analytical model, was performed according to the experimental results obtained with three infilled RC frames models and one bare frames model tested at the LNEC.With a good selection of parametric values, the fairly good fitting between analytical an experimental results, allows to conclude that this model can be used in the more broader framework of Earthquake Engineering and structural reliability of buildings under large intensity earthquakes.
Year: 1993
Number Pages:
9p.
Author(s): Campos Costa, A.; Pires, F.
Editor: Swansea University
Keywords: Analytical modelling; RC frame
Info
Non-stationary models of ground motion.
A stochastic model of earthquake ground motion, with non-stationary amplitude and frequency content, is presented. This model is quantified on the basis of the information available from seismic hazard studies and strong ground motion seismology with the purpose of generating artificial accelerograms to be used in nonlinear analysis and design of structures. The stochastic model is defined by a
Year: 1992
Number Pages:
891-894pp.
Author(s): Duarte, R.T.; Campos Costa, A.
Editor: Balkema, Rotterdam
Keywords: Non-stationary stochastic model
Info
Seismic hazard-consistent studies for Portugal
This paper presents the las developments on seismic hazard analysis directed to the computation of strong ground motion parameters to be applied to nonlinear structural analysis (Campos Costa,1992). It follows the Ishikama and Kameda approach (1988), and makes an application to the Lisbon site. Inhere, the methodology and the most probable seismic scenarios are presented. In an accompagning paper (Duarte et al, 1992), time series generation is obtained for a long distance and short distance earthquake scenarios.
Year: 1992
Number Pages:
477-482pp.
Author(s): Campos Costa, A.; Oliveira, C.S.; Luísa Sousa, M.
Editor: Balkema, Rotterdam
Keywords: Seismic scenarios
Info
Shaking table testing of structures
This paper presents, in the light of LNEC experience in Earthquake Engineering studies, the limitations and advantages of shaking table testing of reinforced concrete and masonry structures. It starts with a general assessment of the contribution of shaking table facilities to the mitigation of earthquake risks and proceeds with a discussion of some specific problems of shaking table performance and testing procedures, like shaking table design alternatives, self-tuning control and numerical evaluation.
Year: 1992
Number Pages:
6837-6846pp.
Author(s): Duarte, R.T.; Ritto-Corrêa, M.; Campos Costa, A.; Vaz, C.T.
Editor: Balkema, Rotterdam
Keywords: Shaking table
Info
Definition and quantification of behaviour coefficients based on structural reliability concepts.
A methodology for the definition and quantification of behaviour coefficients to be used in the earthquake design of structure is presented. These coefficients are defined for specific design methods and are quantified by a target value of the probability of collapse. The methodology is quantified through the analysis and safety checking of structures defined by single variable models.
Year: 1990
Number Pages:
3-12pp.
Author(s): Duarte, R.T.; Costa, A.; Campos Costa, A.
Editor: The Kucherenko Tsniisk of the USSR Gosstroy
Volume:
Vol. 7.
Keywords: Earthquake design; Structural reliability concepts
Info
Dimensionamento inelástico e em torção de estruturas de edifícios em betão armado sujeitos á ação sísmica
Nesta comunicação apresenta-se uma metodologia de quantificação de coeficientes de ductilidade de edifícios em betão armado que apresentam irregularidades em planta, e que possuem uma dada probabilidade de ruína.Foram considerados edifícios de 8 pisos com dimensões em planta 20x15 m2, os elementos resistentes a forças horizontais são pórticos planos e paredes estruturais, sendo a determinação dos valores resistentes elásticos limites feito em função de um dado processo de dimensionamento.Posteriormente, recorrendo a algoritmos de integração passo a passo, acedeu-se ao comportamento inelástico dos edifícios sob a ação sísmica intensa. Deste modo, obtiveram-se os valores máximos das ductilidades impostas, definidas em termos das relações momentos-curvaturas nas secções extremas dos elementos de barra, e para valores crescentes de ação sísmica.O cálculo dos coeficientes de ductilidade foi efetuado tendo em atenção quer os valores das probabilidades de serem excedidas as ductilidades disponíveis quer os potenciais mecanismos de colapso de cada edifício.
Year: 1990
Number Pages:
359-370pp.
Author(s): Campos Costa, A.
Editor: LNEC
Keywords: Dimensionamento inelástico; Edifícios de betão armado; Coeficientes de ductilidade
|
Books
Info
Historical earthquake-resistant timber framing in the mediterranean area
This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe
Year: 2016
Number Pages:
468p.
Author(s): Cruz, H.; Saporiti Machado, J.; Campos Costa, A.; Candeias, P.; Catarino, J. M.
Editor: Springer
Volume:
Vol. 1.
Keywords: Heart 2015 Conference; Historic Masonry; Performance-based Assessment; Structural Health Monitoring; Timber-Framed Construction Systems; Seismic-Resistant Timber Frames; Historical Constructive Analysis; Historical Timber-Framed Walls
Info
Assessment of the seismic capacity of stone masonry walls with block models
The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.
Year: 2011
Number Pages:
221-236pp.
Author(s): Lemos, J. V.; Campos Costa, A.; Bretas, E. M.
: Computational Methods in Earthquake Engineering
Editor: Springer
Volume:
Vol. 21.
Keywords: RTigid blocks; Discrete elements; Seismic assessment; Masonry structures
Info
Earthquake disaster scenario prediction and loss modelling for urban areas
The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies
Year: 2007
Number Pages:
180p.
Author(s): Campos Costa, A.; Carvalho, A. M.
Editor: IUSS Press
Keywords: Shaking scenarios
Info
European manual for in-situ assessment of important existing structures. LessLoss Sub Project 5-In-situ assessment, monitoring and typification of buildings and infrastructure
Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.
Year: 2007
Number Pages:
195p.
Author(s): Campos Costa, A.; Candeias, P.; Mendes, L.; Flesch, R.; Pellegrini, R.; Friedl, H.; Hoffmeister, B.; Oppe, M.; Veit-Egerer, R.; Wenzel, H.; Eusebio, M.
Editor: IUSS Press
Keywords: Structures; Earthquake
Info
Modal analysis from ambient vibration survey of bridges: LNEC experience
In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.
Year: 1999
Number Pages:
712-718pp.
Author(s): Rodrigues, J.; Campos Costa, A.
: Proceedings of the 17th International Modal Analysis Conference : February 8 - 11, 1999 / IMAC XVII.
Editor: SEM
Volume:
Vol. 3727.
Keywords: Dynamic properties; Bridge structures
Info
O Sismo de Northridge, Los Angeles, de 17 Janeiro de 1994. Ensinamentos para Portugal.
O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.
Year: 1995
Number Pages:
165p.
Author(s): Oliveira, C.S.; Costa, A.; Campos Costa, A.; Azevedo, J.; Delgado, R.M.
Editor: IST e FEUP
Keywords: Northridge earthquake; Earthquake effects
|
Capítulo de Livro
Info
Shaping favorable beliefs towards seismic protection through risk communication: A pilot-experience in two Lisbon schools (Portugal).
Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107
Year: 2019
Number Pages:
445-458pp.
Author(s): Silva, D. S.; Vicente, M.; Pereira, A.; Candeias, P.; Ferreira, M.A.; Oliveira, C.S.; Bernardo, R.; Lopes, M.; Henriques, P.
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Non-structural; Protective behaviours; Risk communication; Seismic risk
Info
Characterization of timber masonry walls with dynamic tests
Most of the Lisbon 18th century timber-framed masonry
Year: 2018
Number Pages:
299-309pp.
Author(s): Gonçalves, A.; Candeias, P.; Guerreiro, L.; Ferreira, J.; Campos Costa, A.
: Historical earthquake-resistant timber framing in the mediterranean area
Editor: Springer
Volume:
Vol. 1.
Keywords: Shaking table tests; Timber-masonry walls;
Info
KnowRISK practical guide for mitigation of seismic risk due to non-structural components
Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.
Year: 2018
Number Pages:
309-321pp.
Author(s): Ferreira, M.A.; Oliveira, C.S.; Lopes, M.; Musacchio, G; Candeias, P.; Vicente, M.; Silva, D. S.; O
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Practical guide; Community resilience; Preparedness; Non-structural elements
Info
Elastic and inelastic analyses of frames with a force-based higher-order 3D beam element accounting for axial-flexural-sheartorsional interaction
When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko
Year: 2016
Number Pages:
109-128pp.
Author(s): Correia, A.A.; Almeida, J.P.; Pinho, R.
: Computational Methods in Applied Sciences
Editor: Springer
Volume:
Vol. 3.
Keywords: Inelastic response; Boundary conditions; Flexural-shear-torsional interaction; Higher-order; Force-based; Beam element
Info
A finite-fault modeling of the 1755 Lisbon earthquake sources
A non
Year: 2009
Number Pages:
433-454.
Author(s): Carvalho, A. M.; Campos Costa, A.; Sousa Oliveira, C.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios; Finite-fault modeling
Info
Simulating earthquake scenarios in the european project Lessloss: the case of Lisbon
N/A
Year: 2009
Number Pages:
233-243.
Author(s): Zonno, G.; Carvalho, A. M.; Franceschina, G.; Akinci, A.; Campos Costa, A.; Coelho, E.; Cultrera, G.; Pacor, F.; Pessina, V.; Cocco, M.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios
Info
Shaking table testing
This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM
Year: 2008
Number Pages:
165-196pp.
Author(s): Bairrão, R.
Editor: Springer Verlag
Keywords: Shaking table testing
|
Tese de Doutoramento
Info
Modelos estocáticos para a caracterização da acção sísmica em Portugal Continental
Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte
Year: 2009
Author(s): Carvalho, A. M.
Keywords: Portugal continental; Risco sísmico; Fonte sísmica; Modelos estocásticos; Acção sísmica
Info
Risco sísmico em Portugal Continental
Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.
Year: 2009
Author(s): Sousa, M. L.
Info
Avaliação da vulnerabilidade sísmica de edifícios de alvenaria
O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação
Year: 2008
Author(s): Candeias, P.
Keywords: Reforço sísmico; Vulnerabilidade sísmica; Ensaios sísmicos; Edifícios
|
|
Relatório Científico
Info
Avaliação de risco sísmico do edifício Sede I da EDP - Ensaios in situ de caracterização dinâmica e do comportamento mecânico da estrutura do edifício relatório final
O presente estudo teve como objetivo a caracterização dinâmica e do comportamento mecânico da estrutura do edifício Sede I da EDP, para uma adequada simulação do seu comportamento sísmico. Neste relatório descrevem-se os ensaios de identificação dinâmica in situ realizados, com base em vibrações ambiente e em vibrações forçadas, com o objetivo de recolher informação sobre as propriedades dinâmicas da estrutura como um todo e das suas lajes dos pisos elevados em particular. Foi efetuado o registo e a análise dos sinais de aceleração devido a vibração ambiente, medidos em diversos pontos do edifício, bem como devido a vibrações forçadas impostas num dos pisos enterrados do edifício. São também apresentados e analisados os ensaios de caracterização do comportamento mecânico de componentes estruturais relacionadas com a ligação das lajes mistas dos pisos elevados às paredes dos núcleos resistentes de betão armado do edifício. Estes consistem em ensaios destrutivos de troços de laje mista ligados aos núcleos, por meio de varões selados à parede, e em ensaios de arrancamento desses varões, tendo como objetivo caracterizar os materiais e componentes dos elementos estruturais. Esta informação é essencial para a posterior calibração dos modelos numéricos da estrutura e para uma realista simulação do seu comportamento sísmico, bem como para uma eventual deteção de anomalias estruturais decorrentes de patologias que possam comprometer o desempenho do edifício face à ocorrência de sismos.
Year: 2022
Author(s): Correia, A.A.; Candeias, P.; Ribeiro, F.; Gomes, J. P.
Keywords: Comportamento mecânico; Ensaios in situ; Vibração ambiente; Vibração forçada; Identificação dinâmica
Info
Metodologia para a avaliação da segurança sísmica de edifícios existentes baseada em análises de fiabilidade estrutural - Edifícios de betão armado
A avaliação da segurança sísmica de edifícios existentes tem como quadro de referência o Eurocódigo 8
Year: 2019
Author(s): Sousa, R.; Campos Costa, A.; Costa, A.
Keywords: Análise de fiabilidade estrutural; Metodologias expeditas; Avaliação da segurança sísmica; Edifícios existentes
Info
Mapas de perigosidade sísmica para Portugal Continental: Uma análise crítica - Parte I
Nos estudos probabilísticos para avaliação da perigosidade sísmica, são estabelecidas zonas de geração sísmica (zonas sismogénicas), representando regiões que partilham as mesmas caraterísticas sismológicas, tectónicas e geológicas e definidas as relações entre a frequência com que aí ocorrem os sismos e as respetivas magnitudes, num dado período de tempo. Em 2006, para o Anexo Nacional do Eurocódigo 8, foram consideradas e caraterizadas 11 zonas Sismogénicas para Portugal continental, adaptadas de estudos previamente elaborados em 1996. Entre 2008 e 2009, no âmbito dos projetos ERSTA e SHARE, foram propostas novas zonas sismogénicas, e estimados os respetivos parâmetros da lei de frequência - magnitude. Estas diferentes propostas resultaram em diferentes mapas de perigosidade sísmica para Portugal continental. A SPES, Sociedade Portuguesa de Engenharia Sísmica, espelhando a inquietude existente na comunidade científica face às diversas expressões da perigosidade sísmica em Portugal, e consciente da necessidade de um consenso perante os agentes decisores, considerou urgente a realização de um estudo criterioso acerca das opções tomadas, nos diferentes estudos, e suas implicações. É nestecontexto que surge este trabalho, que pretende fazer uma análise crítica e comparativa dos resultadosobtidos nos diferentes estudos mencionados e as suas implicações ao nível dos períodos de retorno para sismos de maior magnitude. Numa parte II, serão estudadas as implicações em termos de valores da perigosidade sísmica, para vários períodos de retorno e frequências espetrais.
Year: 2018
Author(s): Carvalho, A. M.; Malfeito, N.
Keywords: Sismos; Períodos de retorno; Perigosidade sísmica
Info
Segurança estrutural e sísmica das construções nas intervenções de reabilitação - Enquadramento jurídico da reabilitação urbana síntese dos instrumentos jurídicos e conceitos relevantes
O presente relatório, elaborado no âmbito de um estudo em curso no LNEC sobre a segurança sísmica das construções nas intervenções de reabilitação, sintetiza os instrumentos jurídicos e os conceitos relevantes para a análise do atual regime jurídico da reabilitação urbana (RJRU), e do regime excecional de reabilitação urbana (RERU).
Year: 2015
Author(s): Coelho, E.
Keywords: Instrumentos legais; Reabilitação urbana; Segurança sísmica
Info
Assessment of innovative solutions for non
This document reports the outcomes of the research project
Year: 2013
Author(s): Correia, A.A.; Candeias, P.; Campos Costa, A.; Coelho, E.; Vintzileou, E.; Palieraki, V.; Lourenço, P.; Leite, J.
Keywords: Innovative test setup; Shaking table test; Wire mesh coating reinforcement; Bed joint reinforcement; Reinforced concrete frames; Non-load bearing masonry enclosures
Info
Seismic performance of multi-storey timber buildings - Rusticasa building
This document reports the outcome of the seismic test on the Rusticasa building, the first in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a log house system (LHS). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Lourenço, P.; Branco , J.; Aranha, C.
Keywords: Steel connectors; Shaking table test; Log house system (LHS); Timber buildings
Info
Seismic performance of multi-storey timber buildings - LegnoCase building
This document reports the outcome of the seismic test on the LegnoCase building, the second in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of OSB panels (PF-OSB). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Bartolucci, C.; Tomasi, R.; Grossi, P.
Keywords: Shaking table test; Steel connectors; OSB panels; Timber buildings
Info
Seismic performance of multi-storey timber buildings - Rubnerhaus building
This document reports the outcome of the seismic test on the RubnerHaus building, the third in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of gypsum fibre panel (PF-GF). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Tomasi, R.; Grossi, P.
Keywords: Shaking table test; Steel connectors; Gypsum fibre panel (PF-GF); Timber buildings
Info
Seismic performance of multi-storey timber buildings - TUGraz building
This document reports the outcome of the seismic test on the TUGraz building, the fourth in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a cross laminated system (CTL). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Schickhofer, G.; Flatscher, G.
Keywords: Shaking table test; Steel connectors; Cross laminated system (CTL); Timber buildings
Info
The LNEC earthquake engineering testing facility. Background information: LNEC testing facility, testing setup and protocol and data processing
The TIMBER BUILDINGS Project, led by the University of Trento, included testing of four full scale multi-story timber houses with a realistic horizontal plan and three types of timber housing systems: platform frame system (PFS), log house system (LHS) and cross laminated timber (CLT). The tests were carried in the LNEC-3D shake table under different levels of excitation and different conditions of the structure.The tests were carried with the goal of assessing the seismic performance of the buildings, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.The results were presented in separate reports, one for each building. This document contains information common to the remaining four reports.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Tomasi, R.; Lourenço, P.; Branco , J.; Schickhofer, G.; Flatscher, G.
Keywords: Equipment; Shaking Table; Timber buildings
|
|
|
Outro
Info
Sensibilidade climática, capacidade adaptativa e de vulnerabilidades atuais e futuras da AML
Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.
Year: 2019
Author(s): Marques da Silva, F.; Pinto, A.; Machado, P.
Keywords: Energia; Alterações climáticas
Info
A propósito da forma na engenharia do vento
Análise da forma das edificações nas ações do vento
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Aerodinãmica
Info
Forma e desenho urbano - efeitos na ventilação
As condicionantes arquitetónicas e de urbanização na ventilação natural
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Ventilação
Info
Wind and structures
Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento
Year: 2017
Author(s): Marques da Silva, F.
Keywords: Wind tunnel; Actions on structures; Wind engineering
|