Papers
Info
Aerodynamic characterization of the 516 Arouca Pedestrian suspension Bridge over the Paiva River
Given the 516 Arouca pedestrian suspension bridge
Year: 2023
Number Pages:
18 pp.
Author(s): Marques da Silva, F.
: Wind
Editor: MDPI
Volume:
3.
DOI:
10.3390/wind3010006
Keywords: wind tunnel; wind loading; suspended bridges
Info
Harmonised procedure to update thermal loads in the Eurocodes. Case study for Italy
The characteristic values of temperature corresponding to the maximum and minimum shade air temperature with an annual probability of being exceeded 0.02, used in the European construction standard for thermal actions (EN 1991-1-5:2003), are usually assessed at a country level and included in the National Annexes to that Eurocode part.The paper aims to support national authorities on elaborating maps for thermal actions using publicly available datasets, consistent at a European level, and harmonised modelling approaches. In addition, these datasets are continuously updated, reflecting the current climate and capturing potential global warming variations.The work investigates how updates in data and modelling could affect the characteristic values currentlyadopted in the Italian National Annexes to the Eurocodes. The main results show that: (i) the currently adoptednumber and locations of the weather stations result fairly representative of the patterns detected by exploitingadditional datasets; ii) the statistical method plays an essential role in the assessment of characteristic values, i.e., the method adopted in the current Italian standard evaluates more conservative characteristic values of maximum temperature than Gumbel or Generalized Extreme Value distributions, but could err on the unsafe side for minimum ones; (iii) both E-OBS and ERA5-Land datasets represent two optimal products to be used as a common source of temperature values at European scale; (iv) moving towards an updated period for temperature data results on an increase of characteristic values of maximum temperature and limited variations in spatial extent and magnitude of characteristic values of minimum ones.
Year: 2023
Number Pages:
15p..
Author(s): Rianna, G.; Reder, A.; Luísa Sousa, M.; Dimova, S.
: Climate Services
Editor: Elsevier
Volume:
Volume 30.
Keywords: Thermal load maps; Reanalysis; Eurocodes; Climatic actions; Climate change
Info
Experimental and numerical evaluation of the wind load on the 516 Arouca pedestrian suspension bridge
The present work analyses the wind load effects on the 516 Arouca bridge, the world's longest pedestrian suspension bridge in 2020. Computational fluid dynamics (CFD) was used to model a range of wind incidence angles between -8
Year: 2022
Number Pages:
13pp.
Author(s): Tadeu, A.; Marques da Silva, F.; Ramezani, B.; Romero, A.; Skerget, L.; Bandeira, F.
: Journal of Wind Engineering and Industrial Aerodynamics
Editor: Elsevier
Volume:
220.
Keywords: wind load; suspension bridge; wind tunnel; CFD
Info
Risk and resilience assessment of Lisbon
The safety and resilience of school buildings against natural disasters is of paramount importance since schools represent a reference point for communities. Such significance is not only related to the direct consequences of collapse on a vulnerable part of the population, but also due to the importance of schools in the post-disaster recovery. This work is focused on the risk and resilience assessment of school buildings in Lisbon (Portugal) under seismic events. The results of this study, in which a subset of 32 schools are analyzed, are used to define a prioritization strategy to mitigate the seismic risk of the Lisbon City Council school building portfolio and to assess the overall resilience of the school network. Numerical modeling of the school buildings is performed in order to estimate losses in terms of the built-up area of the schools and recovery times associated with different seismic scenarios, which are probabilistically defined specifically for the sites of the buildings, accounting for the local soil conditions and associated amplification effects. Based on the obtained risk estimates, which are compared to reference values established on international guidelines and specialized literature, the Lisbon City Council and LNEC jointly defined a short- and medium-term risk mitigation plan, starting with a detailed inspection and assessment of the most vulnerable school buildings and continuing to the implementation of retrofitting measures.
Year: 2022
Number Pages:
28p.
Author(s): Ribeiro, F.; Candeias, P.; Correia, A.A.; Carvalho, A. M.; Campos Costa, A.
: Applied sciences
Editor: MDPI journals
Volume:
Vol.12, Issue 17.
Keywords: Recovery planning; Emergency; Decision-making; Numerical modeling; Scenario-based analysis; Risk mitigation; Resilience; Seismic risk;
Info
Aspetos gerais da aplicação em Portugal do Eurocódigo 8
Procuram-se sintetizar neste artigo os principais aspetos relacionados com a avaliação e a reabilitação sísmica de edifícios existentes de alvenaria, compatibilizando a NP EN 1998-3:2017 com os respetivosAnexo C, específico para edifícios de alvenaria, e Anexo Nacional, específico para Portugal.A avaliação sísmica é um procedimento quantitativo através do qual se verifica se um edifício existente, danificado ou não, satisfaz os requisitos de desempenho, definidos por uma combinação de um estado limite com um nível de ação sísmica, através de critérios de conformidade. Neste procedimento estão envolvidos a definição da ação sísmica, a modelação da estrutura, os métodos de análise para determinação dos efeitos das ações e as verificações de segurança. São abordados os métodos de análise, dois lineares e dois nãolineares, aplicáveis a edifícios existentes de alvenaria, bem como as recomendações específicas do Anexo C e as informações complementares do Anexo Nacional.
Year: 2020
Number Pages:
99-120pp.
Author(s): Candeias, P.; Correia, A.A.; Campos Costa, A.; Catarino, J. M.; Pipa, M.; Cruz, H.; Cansado Carvalho, E.; Costa, A.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 12.
Keywords: Eurocódigo 8; Avaliação sísmica; Edifícios de alvenaria existentes
Info
Assessment of seismic vulnerability of non-seismically designed unreinforced masonry buildings through shake table testing
The response of three full-scale unreinforced masonry buildings, without specific seismic detailing, as observed in shake table testing at LNEC for a seismic action representative of induced seismicity, is presented. The first building specimen simulated the upper floor and roof of the end-unit of a two-storey terraced house, built with unreinforced cavity walls, a reinforced concrete slab and a pitched timber roof. The second specimen was a replica of the roof of the first building. The third specimen represented instead a one-story detached pre-1940
Year: 2020
Number Pages:
89-98pp.
Author(s): Correia, A.A.; Mera Marques, A.; Campos Costa, A.; Candeias, P.; Bernardo, V.; Tomassetti, U.; Graziotti, F.; Kallioras, S.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 12.
Keywords: Collapse; Limit states; Induced seismicity; Full-scale shake table test; Unreinforced masonry building
Info
Métodos expeditos para avaliação sísmica de edifícios de alvenaria com pavimentos rígidos
A avaliação da segurança sísmica de edifícios existentes de alvenaria tem como referência os procedimentos dispostos na NP EN 1998-3:2017 (Anexo C) e o respetivo Anexo Nacional, que estabelecem os requisitos de desempenho e os critérios de conformidade para edifícios existentes sujeitos a um determinado nível de ação sísmica. No seguimento das exigências regulamentares, e à luz da verificação da segurança à ação sísmica preconizada na norma, realizaram-se análises probabilísticas de vulnerabilidade sísmica e fiabilidade estrutural a um grande conjunto de edifícios de alvenaria representativos do parque habitacional, que conduziram ao desenvolvimento de métodos expeditos para a avaliação sísmica em alternativa à verificação pelo método de referência. Os métodos propostos permitem avaliar a resistência sísmica de edifícios de alvenaria com pavimentos rígidos, sem recurso a análises numéricas e recorrendo apenas a parâmetros geométricos (Método I) ou em conjunto com as propriedades mecânicas dos materiais (Método II).
Year: 2020
Number Pages:
111-128pp.
Author(s): Bernardo, V.; Campos Costa, A.; Costa, A.; Catarino, J. M.; Candeias, P.
: Revista Portuguesa de Engenharia de Estruturas (RPEE)
Editor: LNEC, APEE, GPBE e SPES
Volume:
Série III, Nº 14.
Keywords: Métodos expeditos; Avaliação sísmica; Pavimentos rígidos; Edifícios existentes de alvenaria
Info
Modulus of elasticity of mortars: Static and dynamic analyses
The analysis and control of deformability of wall coating mortars contributes to minimize crack development and propagation, one of the most common anomalies in building facades. Many of these cracks appear due to internal stresses in the coating mortar, because of imposed deformations or of imposed restrictions by the substrate. These deformability studies should include one or more experimental methods to determine the modulus of elasticity (E) of the coating mortars in question. There are two approaches to experimentally determine E for mortar specimens: static and dynamic experimental methodologies. For civil engineering applications, the results obtained from static methodologies are more adequate than those obtained with dynamic methodologies. However, since static E results are scarce due to a lack of an established static methodology for mortars, mainly due to their lower mechanical resistance, friable behaviour and higher frailty when compared to concrete, engineers are led to use the established dynamic methodologies. This paper proposes an experimental methodology to determine the static E for moulded mortars specimens. The methodology was adapted from the standard procedure used for concrete specimens, to accommodate the specific characteristics of mortar specimens, namely: provide reliable displacement and applied load data; solve issue related to specific mechanical characteristics of mortar specimens, such as low strength and friable behaviour. This methodology was applied to standard moulded mortar specimens made from multiple mineral binders (cement, hydraulic lime and air lime). In order to validate it, the obtained results were compared with two, well-established, dynamic experimental methodologies (Resonance Frequency and Ultrasonic methodologies) as well as with reference values from relevant bibliography. Using the previous data, this paper also includes a preliminary analysis on the ratios between static and dynamic E values for the studied mortars, representing another objective of this study.
Year: 2020
Number Pages:
9p.
Author(s): Mera Marques, A.; Morais, J.; Gil de Morais, P.; Veiga, M. R.; Santos, C.; Candeias, P.; Ferreira, J.
: Construction and Building Materials
Editor: Elsevier
Volume:
Vol 232.
Keywords: Static modulus of elasticity; Deformability; Static and dynamic ratios; Dynamic modulus of elasticity; Mortars
Info
Optical Measurement of Planar Deformations in the Destructive Mechanical Testing of Masonry Specimens
This paper addresses the planar measurement problem in the destructive mechanical testing of masonry specimens, describing the proposed optical measurement solution. The adopted affine geometrical camera model is described as well as its experimental implementation using a digital camera and a measurement referential traceable to the International System of Units (SI). Experimental results from non-destructive tests are presented and discussed, including measurements obtained from the use of classical contact instrumentation. Measurement estimates and uncertainties related to the quantified mechanical properties are also shown.
Year: 2020
Author(s): Lages Martins, L.; Mera Marques, A.; Ribeiro, A.; Candeias, P.; Veiga, M. R.; Ferreira, J.
: applied sciences
Editor: MDPI
Volume:
Vol. 10, issue 1.
Keywords: Optical measurement; Deformation; Masonry specimens; Destructive testing
Info
Revestimentos armados como solução de reabilitação sísmica de paredes de alvenaria de edifícios antigos
As construções antigas fazem parte do tecido histórico das cidades, pelo que é importante proceder a intervenções de reabilitação eficientes, mas não destruidoras da sua identidade e valor cultural intrínseco. A utilização de rebocos armados apresenta-se como uma solução simples e eficaz no reforço sísmico deste tipo de construções, nos casos em que não é possível ou exigível a preservação dos revestimentos de paredes. Neste artigo, são analisadas várias composições de rebocos armados, constituídos por ligantes à base de cal aérea, cal hidráulica ou cimento, com um traço usual e com armaduras constituídas por redes metálicas, redes de fibra de vidro e uma rede de fibra natural. É analisada a capacidade resistente à tração dessesrevestimentos armados, assim como aspetos que podem influenciar a compatibilidade com os materiais existentes, apresentando-se as principais vantagens e desvantagens dos vários tipos de revestimentos.
Year: 2020
Number Pages:
25-36pp.
Author(s): Mera Marques, A.; Veiga, M. R.; Candeias, P.; Ferreira, J.
: Revista Portuguesa de Engenharia de Estruturas (rpee)
Editor: LNEC
Volume:
Série III, N.º 13.
Keywords: Edifícios antigos; Paredes de alvenaria; Reabilitação sísmica; Revestimentos armados
|
Comunicação
Info
Shaking table tests on thin lightly reinforced H-shaped structural walls
The paper presents an experimental program on a 5 storey structural wall physical model performed in LNEC 3D shaking table, in Lisbon, within the Project ECOLEADER-LIS. The characteristics of the reduced model and the test set-up are described, as well as the analysis of the main experimental results. Furthermore the results of numerical simulations are discussed. These tests had the main purpose of studying and evaluating the seismic resistance of thin lightly reinforced structural walls representative of the Central Europe practice. Particular issues have been adressed: (a) To investigate the influence of simultaneous 3D loading conditions. (b) To study walls with T (H) cross-sections. (c) To investigate the free edge of a T (H) shaped walls in compression and different trypes of confinement. (d) To investigate the behaviour of coupled walls and the behaviour of diagonally reinforced coupling beams in thin walls. (e) To calibrate and further develop numerical models. Inelastic dynamic analysis was also performed using Multiple-Vertical-Line-Element-Model (MVLEM), which was extended into 3D and implemented into OpenSees. This macro model proved the ability to simulate and predict the global behavior of the wall as well as the behavior of confined boundary areas and local extensions of longitudinal reinforcement. Considerable overstrength was observed in the wall with minimum reinforcement. However, its deformation capacity was limited to less than 1% of the height. Relatively thick slab enhanced the strength of thin coupling beams considerably. Consequently, they did not perform as expected in capacity design and high axial forces as well as shear failure were induced into the wall piers. The EC8 confining reinforcement proved to be efficient. Simpler details (i.e. U-shaped stirrups) might be acceptable for low walls (5-storey) and/or in the case of low seismic intensity. Sequence of loading and pre-cracking influenced the response considerably. The influence of bi-axial loading was relatively low.
Year: 2006
Number Pages:
10p.
Author(s): Coelho, E.; Campos Costa, A.; Falcão Silva, M. J.; Fischinger, M.
Editor: Swiss Society for Earthquake Engineering and Structural Dynamics ( SGEB )
Keywords: Reinforced concrete; Shaking table
Info
Vibration based damage identification of masonry structures
In the process of preservation of ancient masonry structures, damage evaluation and monitoring procedures are particularly attractive, due to the modern context of minimum repair and observational methods, with iterative and step-by-step approaches. High-priority research issues related to damage assessment and monitoring are global non-contact inspection techniques, sensor technology, data management, diagnostics (decision making and simulation), dynamic (modal) analysis, self-diagnosing / self-healing materials, and prediction of early degradation. On these concerns, the present paper aims to assess damage in masonry structures at an early stage. Replicates of historical constructions were built in virgin state. Afterwards, progressive damage was applied and modal identification analysis was performed at each damage stage, aiming at finding adequate correspondence between dynamic behavior and internal crack growth. Accelerations and dynamic strains were recorded in many points of the replicates. Comparisons between different techniques based on vibrations measurements are made to evaluate different damage identification methods.
Year: 2006
Number Pages:
10p.
Author(s): Ramos, L.F.; Lourenço, P.; Campos Costa, A.; De Roeck, G.
Editor: Macmillan
Keywords: Masonry constructions; Dynamic (modal) analysis
Info
A finite
This work uses a non-stationary stochastic seismological model, based on random vibration theory, for calculating response spectra and synthesizing strong ground motion acceleration records for Portugal Mainland. The validation of the method and comparison with strong ground motion records for Portugal are entirely carried out in terms of 5% damped pseudo absolute response spectra for acceleration. The calibrated model is used to simulate ground motion acceleration for the 1755 Lisbon earthquake. Five potential source rupture models that have been recently proposed by several authors for the 1755 Lisbon earthquake are tested: two analytical models based on hydrodynamic studies; two models based on seismic surveys and on from a recent suggestion based on induced stress changes.For all models, peak ground acceleration maps are compared with iso-intensities map of the earthquake in order to test the ability of the source models for estimating the intensities of the earthquake. The peak ground motion is calculated for different unknown parameters like the rupture velocity, the slip distribution and the nucleation point. The fault parameters like dimension, dip and strike are the ones proposed by the authors of the different analysed source models
Year: 2005
Number Pages:
578-583pp.
Author(s): Carvalho, A. M.; Campos Costa, A.; Oliveira, C.S.
: 250th Anniversary of the I755 Lisbon Earthquake: proceedings
Editor: LNEC
Keywords: Non-stationary stochastic seismological model
Info
Operational modal analysis for damage detection of a masonry construction
This paper presents a dynamic identification analysis of a masonry construction, built to be tested in
Year: 2005
Number Pages:
495-502pp.
Author(s): Ramos, L.; Campos Costa, A.; Lourenço, P.
: Proceedings of the 1st International Operational Modal Analysis Conference: IOMAC
Editor: Aalborg University
Keywords: Rubble stone; Masonry construction
Info
Simulating earthquake scenarios using finite-fault model for The Metropolitan Area of Lisbon (MAL)
In the framework of the ongoing European project
Year: 2005
Number Pages:
164-171pp.
Author(s): Zonno , G.; Carvalho, A. M.; Franceschina, G.; Campos Costa, A.; Coelho, E.; Cultrera, G.; Pacor, F.; Pessina, V.; Cocco, M.; Akinci, A.
: 250th Anniversary of the I755 Lisbon Earthquake: proceedings
Editor: LNEC
Keywords: Seismic risk scenario
Info
Verificación experimental da formulación compleja del rocking motion
En este trabajo se confirma experimentalmente una nueva formulación del problema de los bloques rígidos sometidos a vibraciones externas. Un estudio sistemático de las respuestas del sistema permite determinar los valores de los parámetros relevantes. La nueva formulación hace más sencilla la implementación de técnicas computacionales para el problema da varios tipos de mecanismos acoplados. En las respuestas analizadas, tanto para régimen libre como forzado, se ha observado un buen acuerdo entre teoría y experimento.
Year: 2005
Number Pages:
13p.
Author(s): Prieto, F.; Lourenço, P.; Campos Costa, A.
Editor: SEMNI
Keywords: Construcciones históricas; Rocking motion; Terramotos; Experimental
Info
A stochastic finite
This work presents a non-stationary stochastic seismological model, based on random vibration theory. The model is applied to the 1755 Lisbon earthquake, being a tentative of reproducing the input motion of this severe earthquake. Five possible interpretations of the fault source mechanism, recently proposed by several authors for the 1755 Lisbon earthquake, are analyzed. Three interpretations are based on seismic surveys and two from a suggestion based on induced stress changes. In order to test the feasibility of the different proposed fault source mechanisms to reproduce the historical intensities of the earthquake, ground motion maps were obtained at bedrock level and the degree of the interrelationship between some seismic parameters and the intensities of the earthquake aredescribed by a correlation analysis.
Year: 2004
Number Pages:
15p.
Author(s): Carvalho, A. M.; Campos Costa, A.; Oliveira, C.S.
Editor: 13WCEE Secretariat
Keywords: 1755 Lisbon earthquake
Info
An automatic seismic scenario loss methodology integrated on a geographic information system
The objective of the present paper is to present the new LNEC automatic Seismic Scenario Loss estimate methodology (SSL), integrated on a Geographic Information System (GIS), which comprises modules evaluating bedrock seismic input, local soil effects, vulnerability and fragility analysis and human losses analysis.Results of seismic risk scenarios studies for the Metropolitan Area of Lisbon are presented.
Year: 2004
Number Pages:
13p.
Author(s): Luísa Sousa, M.; Campos Costa, A.; Carvalho, A. M.; Coelho, E.
Editor: 13WCEE Secretariat
Keywords: Seismic scenario loss
Info
Análise experimental para obtenção das características dinâmicas do edifício da Portugal Telecom no Parque das Nações
Este trabalho foi realizado no âmbito do projeto Dynaseis POCTI 36071-2000, cujos objetivos principais são: i) a determinação experimental de frequências próprias e modos de vibração de uma estrutura em betão armado localizada no Parque das Nações em Lisboa; ii) a elaboração do modelo numérico da estrutura e a sua comparação com os resultados experimentais; iii) a avaliação do comportamento da estrutura sob ação sísmica. Neste estudo apresentam-se os resultados dos ensaios experimentais e a comparação com o modelo numérico de elementos finitos (FEM). O edifício escolhido foi a torre da Portugal Telecom
Year: 2004
Number Pages:
565-574pp.
Author(s): Baptista, M.A.; Mendes, P.; Campos Costa, A.; Afilhado, A.; Silva, P.; Oliveira, C.S.
Editor: Universidade do Minho
Keywords: Calibração de modelos numéricos; Ensaios de vibração ambiental; Características dinâmicas
Info
Caracterização do comportamento dinâmico de barragens de betão com base em ensaios de vibrações ambiente e modelos numéricos
Neste trabalho apresentam-se resultados com os quais se pretende mostrar que atualmente já é possível caracterizar o comportamento dinâmico de grandes barragens de betão (frequências próprias e modos de vibração) com base na medição das vibrações ambiente, ou induzidas pelas atividades de exploração. Para tal é importante utilizar instrumentação adequada e uma estratégia de análise e interpretação das medições baseada na utilização conjunta de diferentes metodologias de identificação modal e de resultados de modelos numéricos que permitam simular o comportamento dinâmico do sistema barragem-fundação-albufeira. Este objetivo só pode ser conseguido com uma monitorização em contínuo, a qual permitirá também obter a resposta da estrutura a eventuais ações sísmicas
Year: 2004
Number Pages:
10p.
Author(s): Mendes, P.; Oliveira, S.; Guerreiro, L.; Baptista, M.A.; Rodrigues, J.; Campos Costa, A.
Editor: Universidade do Minho
Keywords: Comportamento dinâmico; Barragens de betão
|
Books
Info
Historical earthquake-resistant timber framing in the mediterranean area
This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe
Year: 2016
Number Pages:
468p.
Author(s): Cruz, H.; Saporiti Machado, J.; Campos Costa, A.; Candeias, P.; Catarino, J. M.
Editor: Springer
Volume:
Vol. 1.
Keywords: Heart 2015 Conference; Historic Masonry; Performance-based Assessment; Structural Health Monitoring; Timber-Framed Construction Systems; Seismic-Resistant Timber Frames; Historical Constructive Analysis; Historical Timber-Framed Walls
Info
Assessment of the seismic capacity of stone masonry walls with block models
The applications of discrete elements models based on rigid block formulations to the analysis of masonry walls under horizontal out-of-plane loading is simplified block pattern are addressed. Two procedures for creating irregular block systems are presented, one using Voronoi polygons, the other based on a bed and cross joint structure with random deviations. A test problem provides a comparison of various regular and random block patterns, showing their influence on the failure loads. The estimation of manual frequencies of rigid block models, and its application to static pushover analyses, is addressed. An example of application of rigid block model to wall capacity problem is presented.
Year: 2011
Number Pages:
221-236pp.
Author(s): Lemos, J. V.; Campos Costa, A.; Bretas, E. M.
: Computational Methods in Earthquake Engineering
Editor: Springer
Volume:
Vol. 21.
Keywords: RTigid blocks; Discrete elements; Seismic assessment; Masonry structures
Info
Earthquake disaster scenario prediction and loss modelling for urban areas
The overall aim of Sub-Project 10 (Earthquake disaster scenario predictions and loss modelling for urban areas) has been to create a tool, based on state-of-the-art loss modelling software, to provide strong, quantified statements about the benefits of a range of possible mitigation actions, in order to support decision-making by urban authorities for seismic risk mitigation strategies. A further larger aim has been to contribute to a seismic risk mitigation policy for future implementation at European level. Among the European cities for which loss estimation studies have been carried out are Istanbul, Lisbon and Thessaloniki, and tools, using GIS mapping, have been developed by research teams in each of these cities; these were made available for further development to examine mitigation strategies within SP10. Related research studies
Year: 2007
Number Pages:
180p.
Author(s): Campos Costa, A.; Carvalho, A. M.
Editor: IUSS Press
Keywords: Shaking scenarios
Info
European manual for in-situ assessment of important existing structures. LessLoss Sub Project 5-In-situ assessment, monitoring and typification of buildings and infrastructure
Much work in Earthquake Engineering was devoted to the improvement of earthquake resistant design of new structures. One European result is EN 1998, which will be in several years the main seismic code for all European countries. But it is well known, that older existing structures cause in many large earthquakes much more casualties and damages than new structures. It is certainly not possible to retrofit all existing structures, but agreement exists, that assessment and retrofit of safety - critical - structures and lifeline structures must have priority. In September 2004 the European Integrated Research Project LESSLOSS on Risk Mitigation for Earthquakes and Landslides was started. The project will run for three years and comprises 13 Sub-Projects (SP´s). The consortium consists of 46 partners (see http:\\www.lessloss.org). LESSLOSS SP5 is on In-situ Assessment, Monitoring and Typification of buildings and Infrastructure. The project partners of SP5 are ARS, CESI, LNEC, RWTH and VCE. This Sub Project focuses mainly on the assessment of important existing structures and tries to integrate experimental methods into the assessment procedure. The progress of SP5 obtained in the first year is summarized in this paper. Highlights presented by all partners are mentioned and the assessment of Hospital Innsbruck is presented in more detail. The most innovative task of LESSLOSS/ SP5 is Update of vulnerability estimates via monitoring, which was also started in the first year.
Year: 2007
Number Pages:
195p.
Author(s): Campos Costa, A.; Candeias, P.; Mendes, L.; Flesch, R.; Pellegrini, R.; Friedl, H.; Hoffmeister, B.; Oppe, M.; Veit-Egerer, R.; Wenzel, H.; Eusebio, M.
Editor: IUSS Press
Keywords: Structures; Earthquake
Info
Modal analysis from ambient vibration survey of bridges: LNEC experience
In order to study the behavior of bridge structures in relation to traffic, wind and seismic loads, it is extremely important to know their actual dynamic properties (natural frequencies, vibration mode shapes and damping). The experimentally identified dynamic properties of bridge structures are also an effective way to characterize their actual global structural behavior. Whether included in the reception load tests of recently built bridges, before they are opened to the traffic, or as part of the inspection works of bridges already in service, LNEC has performed modal analysis studies based on the results of ambient vibration tests. Some of the studies carried out recently in important bridges are reported in this paper.
Year: 1999
Number Pages:
712-718pp.
Author(s): Rodrigues, J.; Campos Costa, A.
: Proceedings of the 17th International Modal Analysis Conference : February 8 - 11, 1999 / IMAC XVII.
Editor: SEM
Volume:
Vol. 3727.
Keywords: Dynamic properties; Bridge structures
Info
O Sismo de Northridge, Los Angeles, de 17 Janeiro de 1994. Ensinamentos para Portugal.
O sismo de Northridge ocorreu na parte norte da área metropolitana de Los Angeles, Califórnia, às 4:31 h do dia 17 de janeiro, uma segunda-feira coincidente com dia de feriado nacional, tendo atingindo uma magnitude de 6.6 na escala de Richter. O número total de vítimas mortais cifra-se em 57, havendo para cima de 8 000 feridos e 20 000 desalojados.As estimativas de perdas totais, feitas em meados de fevereiro de 1994, apontavam para valores de 15 biliões de US dólares, tendo o Estado da Califórnia apresentado um impacto económico total de ordem dos 30 biliões de dólares, perto do valor do Orçamento Geral do estado Português para 1994. Os prejuízos infligidos na indústria e no comércio são também surpreendentemente elevados, exigindo longos períodos de interrupção das atividades económicas.
Year: 1995
Number Pages:
165p.
Author(s): Oliveira, C.S.; Costa, A.; Campos Costa, A.; Azevedo, J.; Delgado, R.M.
Editor: IST e FEUP
Keywords: Northridge earthquake; Earthquake effects
|
Capítulo de Livro
Info
Shaping favorable beliefs towards seismic protection through risk communication: A pilot-experience in two Lisbon schools (Portugal).
Communicating science within disaster risk reduction using methods that encourage two-way dialogue between scientists and laypersons is a challenging task. This paper aims at presenting a methodological strategy of communicating risk and non-structural seismic protection measures through participatory approach. Such methodological strategy is part of a pilot experience of risk communication in two schools in Lisbon (Portugal) under the EU project KnowRISK (Know your city, Reduce seISmic risK through non-structural elements). The efficacy of education for seismic safety is often inhibited by an incomplete understanding of the process by which individuals decide to protect themselves from harm (Becker JS, Paton D,Johnston DM, Ronan KR. Nat Hazards 64(1):107
Year: 2019
Number Pages:
445-458pp.
Author(s): Silva, D. S.; Vicente, M.; Pereira, A.; Candeias, P.; Ferreira, M.A.; Oliveira, C.S.; Bernardo, R.; Lopes, M.; Henriques, P.
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Non-structural; Protective behaviours; Risk communication; Seismic risk
Info
Characterization of timber masonry walls with dynamic tests
Most of the Lisbon 18th century timber-framed masonry
Year: 2018
Number Pages:
299-309pp.
Author(s): Gonçalves, A.; Candeias, P.; Guerreiro, L.; Ferreira, J.; Campos Costa, A.
: Historical earthquake-resistant timber framing in the mediterranean area
Editor: Springer
Volume:
Vol. 1.
Keywords: Shaking table tests; Timber-masonry walls;
Info
KnowRISK practical guide for mitigation of seismic risk due to non-structural components
Good performance of non-structural elements can be decisive in saving lives and costs when an earthquake strikes. The European project KnowRISK aims to educate and encourage households to take the necessary precautionary measures to protect people, houses, and contents. Preparedness and prevention act on community resilience. Within the KnowRISK project, the idea of a Practical Guide has been conceived suggesting seismic mitigation solutions for non-structural components to non-experts stakeholders. It is intended to guide people into the first steps of prevention in a straightforward manner, minimizing or avoiding injuries, damage, and long-term financial consequences. The novelty of the Guide belongs to his philosophy: a path through increasing challenges corresponds to a growing level of safety. The idea is that anyone can mitigate seismic risk in its own environment by adopting simple and low cost measures. The Practical Guide may contribute to increase risk awareness. This kind of initiatives if undertaken at larger scales may also enhance social resilience.
Year: 2018
Number Pages:
309-321pp.
Author(s): Ferreira, M.A.; Oliveira, C.S.; Lopes, M.; Musacchio, G; Candeias, P.; Vicente, M.; Silva, D. S.; O
: Proceedings of the International Conference on Earthquake Engineering and Structural Dynamics
Editor: Springer Link
Volume:
Volume 47.
Keywords: Practical guide; Community resilience; Preparedness; Non-structural elements
Info
Elastic and inelastic analyses of frames with a force-based higher-order 3D beam element accounting for axial-flexural-sheartorsional interaction
When one of the dimensions of a structural member is not clearly larger than the two orthogonal ones, engineers are usually compelled to simulate it with refined meshes of shell or solid finite elements that typically impose a large computational burden. The alternative use of classical beam theories, either based on Euler-Bernoulli or Timoshenko
Year: 2016
Number Pages:
109-128pp.
Author(s): Correia, A.A.; Almeida, J.P.; Pinho, R.
: Computational Methods in Applied Sciences
Editor: Springer
Volume:
Vol. 3.
Keywords: Inelastic response; Boundary conditions; Flexural-shear-torsional interaction; Higher-order; Force-based; Beam element
Info
A finite-fault modeling of the 1755 Lisbon earthquake sources
A non
Year: 2009
Number Pages:
433-454.
Author(s): Carvalho, A. M.; Campos Costa, A.; Sousa Oliveira, C.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios; Finite-fault modeling
Info
Simulating earthquake scenarios in the european project Lessloss: the case of Lisbon
N/A
Year: 2009
Number Pages:
233-243.
Author(s): Zonno, G.; Carvalho, A. M.; Franceschina, G.; Akinci, A.; Campos Costa, A.; Coelho, E.; Cultrera, G.; Pacor, F.; Pessina, V.; Cocco, M.
Editor: L.A. Mendes-Victor et al. (eds)
Keywords: Earthquake scenarios
Info
Shaking table testing
This text reflects the first of the four lectures that the author has presented at Udine, Italy, at CISM
Year: 2008
Number Pages:
165-196pp.
Author(s): Bairrão, R.
Editor: Springer Verlag
Keywords: Shaking table testing
|
Tese de Doutoramento
Info
Modelos estocáticos para a caracterização da acção sísmica em Portugal Continental
Um dos principais problemas e interesses da engenharia sísmica é a caracterizaçãoda acção sísmica, envolvendo a estimativa da intensidade, conteúdo em frequência,duração e variabilidade espacial dos movimentos intensos do solo mais gravosos, emtermos dos seus efeitos nas estruturas, que pode ocorrer num local.O presente trabalho de investigação desenvolve e aplica a metodologia estocástica etécnicas de modelação de fonte
Year: 2009
Author(s): Carvalho, A. M.
Keywords: Portugal continental; Risco sísmico; Fonte sísmica; Modelos estocásticos; Acção sísmica
Info
Risco sísmico em Portugal Continental
Os sismos são encarados frequentemente como desastres naturais inevitáveis. Todavia,deveriam ser considerados fenómenos naturais, cujos efeitos adversos podem ser minimizadoscaso se proceda a uma gestão efectiva do risco sísmico.O objectivo principal do presente trabalho de investigação é o de avaliar o risco sísmicoem Portugal Continental.Sendo um tema de natureza multidisciplinar, apresentam-se e discutem-se modelos deavaliação probabilística da perigosidade sísmica e sua desagregação, de vulnerabilidade efragilidade sísmicas de tipologias construtivas, de danos e de perdas económicas e humanas.Aplica-se a análise probabilística da perigosidade sísmica, e sua desagregação, aPortugal Continental, obtendo-se cenários modais capazes de reproduzir os níveis deperigosidade que os condicionam. Apresenta-se o inventário do parque habitacional e seushabitantes, descriminado por factores de vulnerabilidade, e classifica-se a sua vulnerabilidadesegundo os modelos de dano. Procede-se à actualização e aferição de uma metodologia parasimulação de cenários sísmicos, integrada num Sistema de Informação Geográfico. Avalia-seo risco sísmico, seguindo diversas abordagens, comparando-se os resultados com o risco deoutros países.Construiu-se assim uma ferramenta de avaliação de perdas devidas a sismos, queconstitui uma primeira contribuição para o desenvolvimento de um processo de gestão dorisco sísmico aplicado ao Continente Português.
Year: 2009
Author(s): Sousa, M. L.
Info
Avaliação da vulnerabilidade sísmica de edifícios de alvenaria
O parque habitacional de Portugal Continental contém algumas tipologias construtivas deelevada vulnerabilidade sísmica em relação às quais urge actuar no sentido de reduzir o riscosísmico a elas associado. No projecto de investigação
Year: 2008
Author(s): Candeias, P.
Keywords: Reforço sísmico; Vulnerabilidade sísmica; Ensaios sísmicos; Edifícios
|
Relatório Científico
Info
Avaliação de risco sísmico do edifício Sede I da EDP - Ensaios in situ de caracterização dinâmica e do comportamento mecânico da estrutura do edifício relatório final
O presente estudo teve como objetivo a caracterização dinâmica e do comportamento mecânico da estrutura do edifício Sede I da EDP, para uma adequada simulação do seu comportamento sísmico. Neste relatório descrevem-se os ensaios de identificação dinâmica in situ realizados, com base em vibrações ambiente e em vibrações forçadas, com o objetivo de recolher informação sobre as propriedades dinâmicas da estrutura como um todo e das suas lajes dos pisos elevados em particular. Foi efetuado o registo e a análise dos sinais de aceleração devido a vibração ambiente, medidos em diversos pontos do edifício, bem como devido a vibrações forçadas impostas num dos pisos enterrados do edifício. São também apresentados e analisados os ensaios de caracterização do comportamento mecânico de componentes estruturais relacionadas com a ligação das lajes mistas dos pisos elevados às paredes dos núcleos resistentes de betão armado do edifício. Estes consistem em ensaios destrutivos de troços de laje mista ligados aos núcleos, por meio de varões selados à parede, e em ensaios de arrancamento desses varões, tendo como objetivo caracterizar os materiais e componentes dos elementos estruturais. Esta informação é essencial para a posterior calibração dos modelos numéricos da estrutura e para uma realista simulação do seu comportamento sísmico, bem como para uma eventual deteção de anomalias estruturais decorrentes de patologias que possam comprometer o desempenho do edifício face à ocorrência de sismos.
Year: 2022
Author(s): Correia, A.A.; Candeias, P.; Ribeiro, F.; Gomes, J. P.
Keywords: Comportamento mecânico; Ensaios in situ; Vibração ambiente; Vibração forçada; Identificação dinâmica
Info
Metodologia para a avaliação da segurança sísmica de edifícios existentes baseada em análises de fiabilidade estrutural - Edifícios de betão armado
A avaliação da segurança sísmica de edifícios existentes tem como quadro de referência o Eurocódigo 8
Year: 2019
Author(s): Sousa, R.; Campos Costa, A.; Costa, A.
Keywords: Análise de fiabilidade estrutural; Metodologias expeditas; Avaliação da segurança sísmica; Edifícios existentes
Info
Mapas de perigosidade sísmica para Portugal Continental: Uma análise crítica - Parte I
Nos estudos probabilísticos para avaliação da perigosidade sísmica, são estabelecidas zonas de geração sísmica (zonas sismogénicas), representando regiões que partilham as mesmas caraterísticas sismológicas, tectónicas e geológicas e definidas as relações entre a frequência com que aí ocorrem os sismos e as respetivas magnitudes, num dado período de tempo. Em 2006, para o Anexo Nacional do Eurocódigo 8, foram consideradas e caraterizadas 11 zonas Sismogénicas para Portugal continental, adaptadas de estudos previamente elaborados em 1996. Entre 2008 e 2009, no âmbito dos projetos ERSTA e SHARE, foram propostas novas zonas sismogénicas, e estimados os respetivos parâmetros da lei de frequência - magnitude. Estas diferentes propostas resultaram em diferentes mapas de perigosidade sísmica para Portugal continental. A SPES, Sociedade Portuguesa de Engenharia Sísmica, espelhando a inquietude existente na comunidade científica face às diversas expressões da perigosidade sísmica em Portugal, e consciente da necessidade de um consenso perante os agentes decisores, considerou urgente a realização de um estudo criterioso acerca das opções tomadas, nos diferentes estudos, e suas implicações. É nestecontexto que surge este trabalho, que pretende fazer uma análise crítica e comparativa dos resultadosobtidos nos diferentes estudos mencionados e as suas implicações ao nível dos períodos de retorno para sismos de maior magnitude. Numa parte II, serão estudadas as implicações em termos de valores da perigosidade sísmica, para vários períodos de retorno e frequências espetrais.
Year: 2018
Author(s): Carvalho, A. M.; Malfeito, N.
Keywords: Sismos; Períodos de retorno; Perigosidade sísmica
Info
Segurança estrutural e sísmica das construções nas intervenções de reabilitação - Enquadramento jurídico da reabilitação urbana síntese dos instrumentos jurídicos e conceitos relevantes
O presente relatório, elaborado no âmbito de um estudo em curso no LNEC sobre a segurança sísmica das construções nas intervenções de reabilitação, sintetiza os instrumentos jurídicos e os conceitos relevantes para a análise do atual regime jurídico da reabilitação urbana (RJRU), e do regime excecional de reabilitação urbana (RERU).
Year: 2015
Author(s): Coelho, E.
Keywords: Instrumentos legais; Reabilitação urbana; Segurança sísmica
Info
Assessment of innovative solutions for non
This document reports the outcomes of the research project
Year: 2013
Author(s): Correia, A.A.; Candeias, P.; Campos Costa, A.; Coelho, E.; Vintzileou, E.; Palieraki, V.; Lourenço, P.; Leite, J.
Keywords: Innovative test setup; Shaking table test; Wire mesh coating reinforcement; Bed joint reinforcement; Reinforced concrete frames; Non-load bearing masonry enclosures
Info
Seismic performance of multi-storey timber buildings - Rusticasa building
This document reports the outcome of the seismic test on the Rusticasa building, the first in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a log house system (LHS). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Lourenço, P.; Branco , J.; Aranha, C.
Keywords: Steel connectors; Shaking table test; Log house system (LHS); Timber buildings
Info
Seismic performance of multi-storey timber buildings - LegnoCase building
This document reports the outcome of the seismic test on the LegnoCase building, the second in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of OSB panels (PF-OSB). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Bartolucci, C.; Tomasi, R.; Grossi, P.
Keywords: Shaking table test; Steel connectors; OSB panels; Timber buildings
Info
Seismic performance of multi-storey timber buildings - Rubnerhaus building
This document reports the outcome of the seismic test on the RubnerHaus building, the third in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a platform frame system with sheathing assembled by means of gypsum fibre panel (PF-GF). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Tomasi, R.; Grossi, P.
Keywords: Shaking table test; Steel connectors; Gypsum fibre panel (PF-GF); Timber buildings
Info
Seismic performance of multi-storey timber buildings - TUGraz building
This document reports the outcome of the seismic test on the TUGraz building, the fourth in a total of four buildings included in the TIMBER BUILDINGS Project. This building is a cross laminated system (CTL). The goal of the tests was to assess the seismic performance of the building, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Schickhofer, G.; Flatscher, G.
Keywords: Shaking table test; Steel connectors; Cross laminated system (CTL); Timber buildings
Info
The LNEC earthquake engineering testing facility. Background information: LNEC testing facility, testing setup and protocol and data processing
The TIMBER BUILDINGS Project, led by the University of Trento, included testing of four full scale multi-story timber houses with a realistic horizontal plan and three types of timber housing systems: platform frame system (PFS), log house system (LHS) and cross laminated timber (CLT). The tests were carried in the LNEC-3D shake table under different levels of excitation and different conditions of the structure.The tests were carried with the goal of assessing the seismic performance of the buildings, panel elements and steel connectors, defined in terms of relative displacements and hold-down forces.The results were presented in separate reports, one for each building. This document contains information common to the remaining four reports.
Year: 2013
Author(s): Campos Costa, A.; Candeias, P.; Piazza, M.; Tomasi, R.; Lourenço, P.; Branco , J.; Schickhofer, G.; Flatscher, G.
Keywords: Equipment; Shaking Table; Timber buildings
|
Outro
Info
Sensibilidade climática, capacidade adaptativa e de vulnerabilidades atuais e futuras da AML
Análise dos registos históricos de eventos climáticos e o seu impacto no setor da energia da AML, para identificar o grau em que este setor foi afetado por estímulos relacionados com o clima. Avaliação de capacidades adaptativas.
Year: 2019
Author(s): Marques da Silva, F.; Pinto, A.; Machado, P.
Keywords: Energia; Alterações climáticas
Info
A propósito da forma na engenharia do vento
Análise da forma das edificações nas ações do vento
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Aerodinãmica
Info
Forma e desenho urbano - efeitos na ventilação
As condicionantes arquitetónicas e de urbanização na ventilação natural
Year: 2018
Author(s): Marques da Silva, F.
Keywords: Engenharia do vento; Ventilação
Info
Wind and structures
Caracterização do vento. Ações sobre estruturas. Ensaios em túnel de vento
Year: 2017
Author(s): Marques da Silva, F.
Keywords: Wind tunnel; Actions on structures; Wind engineering
|