Publicações

Portuguese forests are mainly composed of hardwoods, which represent 69% of the forest area in 2010, being Blue gum (Eucalyptus globulus Labill.) the most abundant species (26%). The suitability of Blue gum for structural applications was demonstrated in previous studies. However, the most common uses are still related to the pulp and paper industry as well as energy production, mainly due to sawing and drying issues. The present paper describes a preliminary study on the potential application of non-destructive tests and analytical methods to predict the most important mechanical properties of glued laminated timber (glulam) beams made of Blue gum. The potential of mixed beams made of Blue gum and poplar was also analysed. The longitudinal vibration method and the transformed section method were considered. A total of 11 non-finger jointed full-scale glulam beams (7 of Blue gum and 4 mixed) were manufactured in the laboratory and tested for modulus of elasticity and bending strength assessment. After the bending tests, the density and moisture content of the beams were determined, and the bonding performance was checked by delamination and shear strength tests. Correlation coefficients were established between the predicted values and the experimentally assessed mechanical properties, indicating a huge potential of the predictive methods used. The mechanical properties of non-finger jointed beams tested were above the typical values found in the literature for the most common hardwoods available in European forest.

Reducing the cement content of concrete is of paramount importance towards sustainability, since its production process is highly energy-consuming and delivers massive CO2 emissions to the atmosphere. In this paper, the bond behaviour between steel and stainless-steel reinforcing bars and Low Binder Concrete (LBC), produced with approximately one half and almost one fourth of the minimum cement content prescribed in the standards, is experimentally investigated. Results show the compactness of the mixture to be the main parameter controlling bond development, more than the mixture compressive strength as suggested in published results and standards. A more compact and denser mixture increases the contact surface between the reinforcing bars and concrete, improving friction between both. LBC mixtures with lowered cement content, up to almost one fourth of the minimum recommended, can be used without jeopardizing the bond strength of reinforcing bars. LBC mixturespromise to be a fitting approach towards greater sustainability in the concrete production sector.

Reducing the cement content of concrete is of paramount importance towards sustainability, since its production process is highly energy-consuming and delivers massive CO2 emissions to the atmosphere. In this paper, the bond behaviour between steel and stainless-steel reinforcing bars and Low Binder Concrete (LBC), produced with approximately one half and almost one fourth of the minimum cement content prescribed in the standards, is experimentally investigated. Results show the compactness of the mixture to be the main parameter controlling bond development, more than the mixture compressive strength as suggested in published results and standards. A more compact and denser mixture increases the contact surface between the reinforcing bars and concrete, improving friction between both. LBC mixtures with lowered cement content, up to almost one fourth of the minimum recommended, can be used without jeopardizing the bond strength of reinforcing bars. LBC mixtures promise to be a fitting approach towards greater sustainability in the concrete production sector.

Among biological agents, insect attacks may cause severe degradation of timber structuresin the service life of buildings which leads to lower mechanical performance and, thus, maintenanceproblems over time. Additionally, compression perpendicular to the grain always features a weak spotwith respect to the long-term mechanical performance of timber members and joints. In the presentwork, the respective strength and elastic modulus were thus investigated for insect deterioratedwood. Following a standardized geometry, small samples degraded by anobiids were extractedfrom beams made of sweet chestnut wood (Castanea sativa Mill.) that were removed from service.Visual assessment of the external wood surfaces was then performed to identify areas infested byinsects. Afterwards, destructive monotonic compression tests were carried out perpendicularly tothe grain on the damaged area to determine the loss of compressive strength and elastic modulus.The experimental results showed that the loss of compressive strength and elastic modulus mightbe linearly correlated to the wood density loss for small samples infested by insects. Nonetheless,future work should focus on determining accurately the density loss in the insect-deteriorated partthrough non- or semi-destructive tests, in order to establish stronger relationships with the mechanicalproperties loss investigated.

In the present work, and for the first time, totally biosourced low-density particleboardswere produced using cardoon particles (a no added value by-product from the Portuguese cheese making industry), bound with a potato starch adhesive. Different starch/cardoon ratios (0.6, 0.8, 1 and 1.2) were tested and the effect of different bio-based additives (chitosan, wood fiber and glycerol) on the performance of the adhesive system was evaluated. The best result was obtained for a formulationwith a starch/cardoon mass ratio of 0.8, a chitosan/starch mass ratio of 0.05 and a water/starch mass ratio of 1.75. The particleboards produced had a density of 323 kg-m-3, internal bond strength of 0.35 N.mm-2 and thickness swelling of 15.2%. The values of density and internal bond strength meet the standard requirements of general-purpose lightweight boards for use in dry conditions according to CEN/TS 16368 specification. Moreover, the susceptibility of the formulations with best results was established against subterranean termites and one decay fungi.

There is a need for new solutions in wood protection against marine wood borers andtermites in Europe. A new solution could be the esterification of wood with sorbitol and citric acid(SCA) since these are inexpensive and readily available feedstock chemicals and have shownprotective properties against fungal wood degradation in earlier studies and preventedmacrobiological degradation, as shown in this study. Protection of wood products in the marineenvironment lacks available wood preservatives that are approved for marine applications. Termiteinfestation is opposed mainly by biocide treatments of wood. Several wood modification systemsshow high resistance against both marine borers and subterranean termites. However, the existingcommercialized wood modification products are costly. Both macrobiological forms of degradationrepresent a great threat for most European wood species, which are rapidly and severely degradedif not properly treated. This study investigated esterified wood in standard field trials againstmarine wood borers, and against subterranean termites in laboratory trials in a no-choice and choicetest. The treatment showed good resistance against wood borers in the marine environment afterone season and against subterranean termites in the laboratory after eight weeks. The low termitesurvival rate (SR) in the no-choice test during the first week of testing indicates a mode of actionthat is incomparable to other wood modification treatments.

Due to its average mechanical properties, poplar, a fast-growing species, has been disfavored compared to stronger species for several decades. Wood-based products may help changing that perspective and thus, poplar has been gaining its marketshare for structural uses. A state-of-the-art review concerning the use of poplar to produce glued laminated products, with special focus on the use of Portuguese poplar, is presented. The Portuguese forest produces a great variety of species. Themost common poplar species found in this country are Populus x canadensis, P. nigra L., and P. alba L. Despite its limited availability, and the market hesitation on its structural application, recent studies on poplar grown in the Portuguese forestshowed its suitability for structural purposes. Glued laminated timber (GLT) beams made with this species revealed a very promising mechanical behavior. Bending strength tests evidenced a ductile behavior on more than 70% of the beams, whichmotivated deepening the study on the raw material used to produce those beams. To predict the mechanical behavior of such beams, a 3D numerical model was developed. The numerically predicted results were compared with the experimental ones,showing very good agreement between both approaches.

O betão com baixa dosagem de ligante (LBC - low binder concrete na denominação anglo-saxónica) e o betão com baixa dosagem de cimento com agregados reciclados (LCRAC - low cement recycled aggregate concrete ) são alterativas eco-eficientes ao betão de cimento Portland com agregados naturais por apresentarem um menor impacto ambiental. Para contribuir para o estudo da viabilidade de aplicação estrutural do LBC e do LCRAC, apresentam-se neste artigo os resultados obtidos numa campanha experimental de ensaios de arrancamento (pull-out tests), realçando o desempenho obtido ao nível da relação entre a tensão de aderência e o deslizamento do varão de aço. Os resultados experimentais foram comparados com as propostas de previsão existentes e apresenta-se uma primeira proposta de lei para descrever a relação tensão de aderência-deslizamento, considerando a compacidade, os agregados reciclados, o diâmetro do varão e a respetiva área relativa das nervuras transversais. A influência positiva da compacidade na aderência foi validada através da comparação dos resultados obtidos com os resultados decorrentes da proposta existente no Model Code 2010.

In this article, an assessment method toestimate the residual strength of pine structural ele-ments degraded by anobiids is presented. This novelmethod was developed in the laboratory to be usedin situ and is based on the strength required to withdrawa screw on the surface of degraded timber. Samples ofdegraded maritime pine (Pinus pinaster Ait.) weresubmitted to micro-computed tomography (l-XCT) toquantify density loss. This parameter is highly corre-lated with mechanical properties thus central for theassessment of timber structural capacity. Density lossvalues have been correlated with both screw withdrawalforce and shear parallel to the grain strength showingsignificant relationships between these parameters.Using these correlations, the density loss of a degradedelement and its shear strength parallel to the grain viathe screw withdrawal force can be estimated enabling avalid quantitative assessment of the timber elementsresidual strength and, therefore, contributing to reduceunnecessary replacement, to boost eco-efficient inter-ventions and to provide foundations required to performexperimental modelling tests.

O risco refere-se à probabilidade de ocorrerem danos causados pela manifestação de um determinado perigo, sendo função da perigosidade, da exposição (de pessoas e bens) e da vulnerabilidade dos elementos expostos face a esse perigo.Um componente essencial da avaliação do risco è a análise da perigosidade associada aos perigos identificados num dado território, sejam de origem natural ou decorrentes da ação humana. Outro componente essencial é a análise dos elementos (pessoas e bens) expostos aos perigos, bem como as características que contribuem para a suavulnerabilidade - ou a sua resiliência em situação de acidente grave ou de catástrofe. Nesta comunicação dá-se conta de alguns estudos desenvolvidos pelo LNEC nos domínios da avaliação da perigosidade e da vulnerabilidade sísmica das construções, da perigosidade de agitação costeira e risco de galgamentos costeiros e da avaliação da vulnerabilidade de edifícios aos incêndios florestais.

Tabique is one of the main Portuguese traditional building techniques which use earth as a building material. In general, a tabique building component is formed by a simple timber structure covered by an earth based mortar on both sides. The mortar has an important role in this system because it protects the internal timber structure as well as it is a coating. Trás-os-Montes and Alto Douro, is the northeast region of Portugal and it is rich in terms of tabique heritage construction. Meanwhile, previous research works have shown that the existing tabique constructions, in this region, show a generalized advanced stage of deterioration. This aspect associated to the fact that there is still a lack of scientific studies done in this field motivated this research work, which its main objective is to identify and to understand the structural system of tabique dwellings. A two storey tabique dwelling located in Lamego Municipality, near Douro River, in the UNESCO classified heritage area, is used as reference in this study. Building details of the original applied structural system solutions are shown and described. The adopted connection solutions between structural components are some of the above building details which are introduced and described. Finally, the conservation stage of these elements is also analysed.

O presente trabalho apresenta um modelo analítico para o cálculo das deformações globais (deformação axial e rotação) de uma secção rectangular, em função dos esforços actuantes (esforço normal e momento flector), em regime elástico e elastoplástico, sem impor a priori uma determinada relação entre os valores destes esforços. A sua aplicação cobre os materiais com endurecimento em regime plástico e com comportamento elastoplástico perfeito, dispensando o recurso a análises iterativas, baseadas numa discretização da secção, para a determinação das deformações globais. Este modelo proporciona ainda uma base para a formulação de outros modelos análogos para o cálculo de secções estruturais correntes (em I ou RHS, p. ex.).

Este artigo apresenta o trabalho realizado com o objectivo de caracterizar o comportamento mecânico e desenvolver métodos de classificação visual e mecânica para a madeira de secção circular de Pinheiro bravo. Duas amostras, uma de 200 toros e uma outra de 59, foram obtidas numa zona do interior centro de Portugal. Após secagem, os toros foram analisados visualmente, sujeitos a ensaios não destrutivos para determinação do módulo de elasticidade dinâmico e, finalmente, sujeitos a ensaios destrutivos para a determinação da resistência à compressão e flexão, e módulo de elasticidade, segundo a norma EN 14251. Com base nos resultados obtidos, foram analisadas as características visuais mais adequadas para uso no processo de classificação visual. Como resultado desta análise foi desenvolvida uma proposta de classificação visual para aplicação à madeira de secção circular de Pinheiro bravo. This paper presents work carried out with the aim of characterizing the mechanical behaviour and developing visual and mechanical strength grading systems for Portuguese Maritime pine roundwood. Two samples, one of 200 Maritime pine logs and another of 59, were collected in an interior central region of Portugal. After drying, the logs were visually graded, subjected to non destructive tests for determination of dynamic modulus of elasticity and, finally, subjected to destructive tests, for determining its bending and compression strength and bending modulus of elasticity, according to EN 14251. Based on results, conclusions were drawn regarding the most appropriate features to be used in the visual strength grading process. From this analysis a proposal was developed to visually grade Portuguese Maritime pine roundwood.

A conservação da madeira em edifícios, entendida como o conjunto de acções destinadas a prolongar a sua vida útil, é essencial para a manutenção da autenticidade e integridade do património construído. O conceito de

: Os prumos telescópicos extensíveis são elementos estruturais correntemente utilizados em trabalhos de construção, reforço ou reabilitação de estruturas permanentes, tipicamente lajes de edifícios. Servem de suporte a essas estruturas, devido à sua insuficiente capacidade resistente ou rigidez. Foi recentemente concluído no LNEC um estudo experimental com o objectivo de avaliar o comportamento estrutural e a resistência última destes elementos estruturais. Este trabalho tem como objectivo destacar a importância do controlo da Qualidade dos prumos telescópicos extensíveis, muitas vezes produzidos em países onde não são respeitadas as exigências da normalização europeia em vigor em Portugal

A reparação ou reforço de elementos degradados em estruturas de madeira em serviço pode em alguns casos ser feita com a introdução de próteses de madeira nova, ligadas à madeira existente através de chapas ou varões colados. Nestas intervenções são geralmente usadas colas epoxídicas, por serem as mais adequadas à execução de colagens em obra. O principal inconveniente destas colas é o facto de serem bastante sensíveis a temperaturas de serviço elevadas, resultando na redução da resistência e da rigidez das juntas coladas.Estudos anteriores realizados no LNEC mostraram que a resposta das colas epoxídicas à temperatura pode ser melhorada com o aumento da temperatura durante o processo de cura ou com a pós-cura das juntas de madeira coladas. Esta comunicação apresenta o trabalho experimental, desenvolvido no LNEC, sobre a influência da aplicação de pós-cura em juntas coladas com colas epoxídicas através de resistências eléctricas embebidas na linha de cola. Os resultados mostram que a aplicação de pós-cura pelo método proposto melhora efectivamente o comportamento das juntas coladas, face à situação da junta colada simples. Repair or strengthening of damaged structural timber members can sometimes be made with the introduction of prostheses of new timber glued to the old one through plates or rods. In these interventions epoxy adhesives are commonly used, as they are most suitable for in situ work. The main drawback of these adhesives is that they are very sensitive to high service temperatures, resulting in reduced strength and stiffness of the bonded joints.Previous studies conducted at LNEC showed that the response of epoxy adhesives to temperature can be improved by increasing the temperature during the curing process or by the application of a post-curing. This paper presents the experimental work, developed at LNEC, on the influence of post-cure of bonded joints, applied by electrical heating resistances embeded in the adhesive mass. The results show that the application of a post-cure with the proposed technique improves the performance of bonded joints, as compared to the situation of the simple glued joint.

Bridge falsework systems are frequently used in the construction, rehabilitation and retrofit of bridge structures. These structures have a significant impact on the cost, construction rate and construction safety of the supported permanent structures. However, the relevant stakeholders often do not consider them as important as permanent structures, and in the recent years a high number of accidents involving bridge falsework systems have been reported. A research programme was initiated aiming to contribute to a better knowledge about the structural behaviour, reliability and robustness of bridge falsework systems. In this paper the results of a series of bending tests of ledger-to-standard Cuplok® joints will be presented and discussed.

A avaliação de estruturas de madeira em serviço requer conhecimentos específicos e experiência, suscitando muitas vezes dificuldades aos agentes envolvidos na reabilitação de edificios. Esta comunicação apresenta uma metodologia para inspecção, avaliação e quantificação da segurança de estruturas de madeira em serviço e refere alguns princípios que devem reger as intervenções de conservação subsequentes.

O SIMPOLE (SIMulator of POLEs) é um programa de computador, construído em VBA (Visual Basic for Applications) do Microsoft Excel®, constituído por 2 módulos. O primeiro módulo é responsável pela geração da geometria do toro e distribuição de nós ao longo do seu comprimento. É possível, igualmente, a inserção destas características por parte do utilizador. O segundo módulo permite o ensaio do toro, gerado ou inserido, segundo o preconizado na norma EN14229. O SIMPOLE tem como output final a resistência à flexão e o módulo de elasticidade do toro, bem como a localização e causa de rotura. Este programa terá como principal aplicação a determinação das características mecânicas de toros procedentes de uma floresta, conhecendo as distribuições estatísticas dos defeitos e das características mecânicas da madeira limpa. Este programa, não finalizado, carece de validação, apresentando-se neste artigo os princípios e procedimentos do software desenvolvido. SIMPOLE (SIMulator of POLEs) is a computer program, built in VBA (Visual Basic for Applications) of Microsoft Excel Excel®, that is composed by two modules. The first module comprises the geometry generation of the pole and the distribution of knots along its length. It is also possible the definition of these characteristics by the user. In the second module, the poles are tested according to standard EN14229. SIMPOLE outputs are the bending strength and modulus of elasticity of the pole, as well as the location and cause of failure. The mains use of SIMPOLE will be the determination of mechanical properties of logs from a forest stand, knowing the statistical distribution of defects and clear wood mechanical properties. This program, not yet finalized, needs validation, being presented in this paper the principles and procedures of the software.

Plastering and rendering mortars anomalies are frequently associated to cracks, leakages, fungi colonization, etc. Frequently, these anomalies are related to the presence of moisture or lack ofventilation and thermal insulation from these materials. To try to reduce these problems and to improve the properties of the plastering and rendering mortars, a new material was tested that is mortars incorporating regranulated of expanded cork (REC), a sub-product of the cork industry. The objective of this work was to obtain mortars with better thermal insulation, reducing the condensation problems in walls. Results of the experimental tests conducted are presented for the evaluation ofproperties of the new material. The material proved to be a promising solution in relation to the classical cement mortar and can be applied to rehabilitate similar types of plastering mortars.

N/A

N/A

N/A

N/A

O Museu da Academia das Ciências de Lisboa possui uma preciosa xiloteca assinada pelo Mestre dos marceneiros portugueses, José Aniceto Rapozo contendo 1213 amostras de madeiras do Brasil e 12 de outras origens. A sua importância no progresso do conhecimento dos recursos florestais do Brasil naviragem dos séculos dezoito e dezanove conduziu ao estudo em curso. Dada a devastação verificada em vastas áreas florestais brasileiras, surgem dificuldades por certas espécies poderem ter distribuiçãogeográfica diferente (com eventual extinção, geral ou localizada), por insuficiência do material de comparação, e por ambiguidade das designações comerciais.Foi possível identificar esta xiloteca como uma de quatro encomendadas a Aniceto Rapozo pelo Príncipe Regente. A análise das amostras de madeira e a informação documental mostram que a colecçãotem por base uma remessa de 5008 amostras de madeiras do Brasil enviada em 1784 para o Arsenal Real do Exército, em Lisboa, pelo Vice-Rei do Brasil, Luís de Vasconcellos e Souza.O valor científico do conjunto é evidenciado pela identificação botânica das espéciesrepresentadas. Na situação actual, a identificação das espécies florestais representadas na amostragem foiinteiramente conseguida em 14% dos casos, conseguida mas ainda por confirmar em 27%. Dado o carácter preliminar deste estudo, os seus resultados serão ulteriormente publicados com mais pormenor. Among the Lisbon Academy of Sciences Museum collection there is a valuable xylarium by theleading Portuguese master cabinet-maker José Aniceto Rapozo (1756-1824), comprising 1213 wood samples from Brazil plus 12 from elsewhere. This collection is most important since it allows us to improve the knowledge on Brazilian forest resources by the end of the eighteenth century and thebeginning of the next. This study aims to establish its historical framework and scientific value. Owing tooverexploitation and even devastation of very large forest areas in Brazil, difficulties for our study aroseeither as some species may have now a different geographical distribution (and eventually may have underwent local or general extinction), by lack of adequate comparison material, or because of ambiguityof the commercial names.Results so far obtained allowed us to recognize the xylarium as one of the four commanded Rapozo by the Regent Prince, later King João VI (1767-1826). Taking into account the wood samples analyses as well as bibliographic data it is possible to conclude that the collection was prepared from a set 3 of 5008 Brazilian wood samples sent to the Royal Arsenal in Lisbon in 1784 by the Brazil

This work collects information about laboratory tests to evaluate the properties of agro-industrial wastes used for thermal insulation building materials considering them individually and in composits. It focuses on bio-susceptibility, as one of the main aspects to consider for bio-based building products.

Innovation in structures and construction materials demands a more accurate performance analysis during the life cycle. In addition, climatic changes pose new challenges to civil infrastructures that were not so relevant in the past. In most cases, the traditional test methods cannot accurately assess the complex phenomena involved in durability. The modern and complex factors require a different approach to durability analysis. The purpose of this chapter is to present innovative durability tests on construction materials: wood; rammed earth, cob and unfired blocks; natural stone; bituminous binders and mixtures; and Fibre Reinforced Polymers (FRP) to concrete bonded connections. Most of these tests concern the accelerated simulation of the main phenomena involved in durability performance

Laboratory tests were carried out to define production parameters of innovative eco-efficient composites made up of hazelnut shells as aggregate and a sodium silicate solution as adhesive. The aim was to maximize the content of bio-aggregates and minimize the amount of adhesive, guaranteeing the feasibility of producing samples. Therefore, after preliminary testing, the percentages of hazelnut shells and the sodium silicate solution were kept constant: 70% and 30% of the total volume, respectively. However, the characteristics of the considered composites did not allow the production of uniform samples. The sodium silicate solution was not rapidly absorbed by the bio-aggregates; during the drying process, it was deposited on the bottom side of the samples. The uniformity of the samples is required to guarantee a correct evaluation of their performance and future homogeneous panels. Hence, different production parameters were investigated, such as drying at T

The durability of construction materials is a key concern and can be related to different actions such as weathering conditions outdoors enhanced by climatic change, chemical and biological attack, abrasion, and other conditions of service over time. Frequently, several actions develop simultaneously, making it difficult to reproduce in situ conditions in laboratory. Furthermore, testing to assess durability depends largely on the nature of the material itself or on the way it has been assembled with other materials. The ageing techniques to assess long-term durability performance of construction materials are based on accelerated durability tests, which include, for example, thermal stress, freeze

This paper presents an overview of research carried out to assess the bonding suitability of Portuguese timbers.Most work developed in the last decades has focused Maritime pine timber, due to its traditional use in building construction, good mechanical properties and availability. Untreated, as well as preservative treated Maritime pine have been studied, as its impregnability allows deep treatment suitable for applications in Use Classes 3 and 4.Recent results on bonding preservative treated Maritime pine wood are discussed.Preliminary results regarding other species that are becoming available in the Portuguese market are also presented, as an attempt to reduce pressure on Maritime pine timber as well as to seek more valuable alternatives for their traditional uses.

No presente trabalho apresentam-se os resultados mais relevantes obtidos num programa experimental desenvolvido no LNEC com o objetivo de caracterizar a aderência dos varões nervurados do tipo A500NR SD existentes no mercado, fundamentalmente para melhorar a modelação do comportamento dos elementos de betão armado de zonas críticas de estruturas inseridas em zonas sísmicas.O programa experimental desenvolvido pretende simular as condições de aderência existentes num varão horizontal de uma ligação viga-pilar e tem como principais variáveis varões de dois diâmetros frequentemente utilizados (16 e 25 mm), dois níveis diferentes de área relativa das nervuras (A e B) e duas classes de betão (C1 e C2), ambos representativos do betão utilizado nas construções mais relevantes.Os resultados obtidos quer nos ensaios monotónicos quer nos ensaios cíclicos apontam para um decréscimo da tensão de aderência com o aumento do diâmetro da ordem dos 10%. O aumento da área relativa das nervuras transversais traduz-se num incremento da tensão máxima de aderência da ordem dos 15%, com uma redução do deslizamento que ronda os 15%. Nesse sentido, este estudo propôs que, no caso dos varões com maior área relativa das nervuras, a tensão de aderência máxima possa variar entre 2,35 e 2,65 vezes a raiz quadrada da resistência do betão à compressão e que o patamar onde a tensão de aderência é máxima se situe entre 0,5 e 1,5 mm de deslizamento.Explorou-se também o fenómeno da entrada em cedência da armadura tendo-se concluído que, em provetes que pretendem simular as condições de aderência existentes num varão horizontal de uma ligação viga-pilar, a entrada em cedência da armadura conduz a uma redução da tensão de aderência máxima inferior a 10%, quer regime monotónico quer em regime cíclico.

O presente trabalho de investigação refere-se à conservação de elementos estruturais de madeira medianamente degradados por fungos em edifícios antigos. Propõe-se estudar a compatibilidade entre produtos de tratamento e de consolidação por impregnação, aplicados sequencialmente. A avaliação do processo foi realizada maioritariamente em laboratório e na óptica do desempenho mecânico conjunto da madeira e produtos aplicados, por intermédio de ensaios físico-mecânicos destrutivos e não destrutivos e também por ensaios mecânicos não destrutivos realizados in situ. Foram utilizados produtos comerciais, aplicando-os às espécies de madeira correntemente encontradas nos edifícios antigos da zona de Lisboa: Pinho bravo e Casquinha. Procedeu-se à avaliação mecânica de madeira nova e antiga, em estado são e degradado; ao desenvolvimento de um método de medição da profundidade de penetração de produtos de tratamento; à avaliação da capacidade consolidante de madeira degradada por produtos poliméricos fluidos e à avaliação da sua actuação conjunta, estudada com e sem envelhecimento artificial. Os resultados obtidos indicaram significativos aumentos de capacidade mecânica da madeira degradada, quando submetida a tratamento e consolidação Este trabalho desenvolve, assim, uma proposta de solução para a madeira que não se encontra sã, mas que ainda possui capacidade resistente, não necessitando, por isso, de ser removida. O processo de tratamento e consolidação promove resistência aos agentes biológicos e, simultaneamente, recuperação de alguma resistência mecânica da madeira, conferindo-lhe capacidade para continuar em serviço.

Subterranean termites from the genus Reticulitermes are an important pest ofwood in service throughout southern Europe and elsewhere. For effective termitecontrol with long term protection but minimal environmental damage, newintegrated approaches to termite management are needed. Baiting-based systemsseem to be promising non-traditional methods for termite control, targeting thecolony as a whole. However, control through baiting is only feasible when it isknown that the toxicant can be transferred to all the colonies foraging on theinfested area and also throughout each individual colony. Accordingly, the workdescribed is specifically designed to achieve a better understanding of thedistribution and delimitation of colonies within a population of Reticulitermes,with parallel insights into foraging behaviour and colony organization.Initially, the species/subspecies spectrum present within the notionalReticulitermes group in Portugal was reassessed. It was shown that Reticulitermesgrassei is the only species encountered. Foraging activity was then assessed in anexperimental woodland site over two successive annual cycles, both by thesampling of natural lying dead wood and by a standard baiting grid. R. grasseiseem to select wood with larger diameter, with an apparent preference for materialalready decayed by fungi. Both termite and fungal attack on wood seems to bepromoted by higher moisture levels, such as prevail in larger litter items andduring seasonal rains. Termites were unable to detect and direct their foragingtowards sound wood in laboratory conditions, suggesting that the network ofinfochemical signals is more complex than just volatiles emanating from soundwood. Mark-release-recapture (MRR) was used to delineate foraging groups,which were then allocated to their parent colonies by the use of microsatellitemarkers. The results suggest that resource sharing is a facultative behaviour,specifically when food is not a limiting factor for colony development. Theimplications of all these findings for bait technology and protocols are discussed,with reference to the local population ecology of Reticulitermes.

The project CircularBuild -

Relatório final do projeto PTDC/ECM/099121/2008

O presente trabalho apresenta um projecto de versão portuguesa da Norma Europeia EN 10002-2, e insere-se numa série de estudos programados pelo autor, enquanto coordenador da normalização nacional no domínio dos ensaios mecânicos, físicos e não-destrutivos de materiais metálicos.O texto do projecto de norma apresentado consiste na versão final de uma proposta redigida pelo autor, na sequência dos estudos efectuados ao nível da Comissão Técnica de Normalização competente.

O presente trabalho apresenta um projecto de versão portuguesa da Norma Europeia EN 10002-5, e insere-se numa série de estudos programados pelo autor, enquanto coordenador da normalização nacional no domínio dos ensaios mecânicos, físicos e não-destrutivos de materiais metálicos.O texto do projecto de revisão apresentado consiste na versão final de uma proposta redigida pelo autor, na sequência dos estudos efectuados ao nível da Comissão Técnica de Normalização competente.

O presente relatório descreve a participação do LNEC no programa europeu de intercomparação de calibrações de forças

O presente trabalho apresenta um projecto de revisão da Norma Portuguesa NP 850 (1985)

O presente trabalho apresenta um projecto de revisão da Norma Portuguesa NP 386 (1965)

O presente trabalho apresenta um projecto de revisão das Normas Portuguesas NP 449 (1966)

O presente trabalho apresenta um projecto de revisão da Norma Portuguesa NP 450 (1966)

O presente trabalho apresenta um projecto de Norma Portuguesa relativo ao ensaio de dilatação de anéis de tubos metálicos, e insere-se numa série de estudos programados pelo autor, enquanto coordenador da normalização nacional no domínio dos ensaios mecânicos, físicos e não-destrutivos de materiais metálicos, com a finalidade de preencher lacunas da Normalização Portuguesa neste domínio que a indústria e as instituições ligadas ao controlo da qualidade considerem ser mais urgente colmatar.O texto apresentado consiste na versão final de uma proposta redigida pelo autor, na sequência dos estudos efectuados ao nível da Comissão Técnica de Normalização competente.

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A