Publicações

o obtain predictions closer to concrete behaviour, it is necessary to employ a particle model(PM) that considers contact softening. A bilinear softening contact model (BL) has been adoptedin PM studies. Several limitations in PM predictions have been identified that may be due to BLassumptions. For this reason, this paper compares BL predictions with those obtained with morecomplex models to assess if PM predictions can be improved. As shown, it is possible to calibrateeach contact model to reproduce the complex behaviour observed in concrete in uniaxial and biaxialloading. The predicted responses are similar, and the known PM limitations still occur independentlyof the adopted model. Under biaxial loading, it is shown that a response closer to that observed inconcrete can be obtained (higher normal-to-stiffness ratio of

A three-dimensional particle model, based on the asphalt mastic micro-structure representation following a discrete element model framework, was developed to investigate the influence of sunflower oil (rejuvenator) on the rheological properties of asphalt mastic. Dynamic shear rheometer tests in laboratory, for a frequency range of 0.1

The out-of-plane flexural bending capacity of masonry is a fundamental property for understanding the behavior of masonry structures. This study investigates the behavior of unreinforced masonry wallettes subjected to combined compression-flexural loading using the discrete element method (DEM), and provides a novel framework to estimate the masonry strength. A simplified micro-modeling strategy is utilized to analyze a masonry wallette, including the variation of the mechanical properties in masonry units and joints. Stochastic DEM analyses are performed to simulate brickwork assemblages, assuming a strong unit-weak joint material model typical of most masonry buildings, including historical ones. Once the proposed computational approach is validated against the experimental findings, the effect of spatial and non-spatial variation of mechanical properties is explored. Two failure types are identified: joint failure and brick failure. For each failure mechanism, the variability of the response and the effects of the modeling parameters on the load-carrying capacity is quantified. Afterward, Lasso regression is employed to determine predictive equations in terms of the material properties and vertical pressure on the wallette. The results show that the most important parameters changing the response are the joint tensile strength and the amount of vertical stress for joint failure, whereas the unit tensile strength dominates the response for brick failure. Overall, this research proposes a novel framework adopting validated advanced computational models that feed on simple test results to generate data that is further utilized for training response prediction models for complex structures.

Discrete element models are being increasingly applied to model rock failure processes.Bonded-particle models, based on circular or spherical particle systems, have been successfully usedfor two decades. More recently, bonded-block models, using polygonal or polyhedral elements, have proven to be a powerful alternative. This paper describes the basis of the application of these models in the numerical simulation of failure in rock materials. The critical governing parameters are identified, and their influence is discussed. The model calibration procedure based on the analysis of laboratory tests is discussed. An application example of an underground excavation problem is presented using a simple bonded-block model employing rigid blocks and a bilinear softening contact model. The results show the capability of this approach to reproduce observed failure modes involving block fractures.

Masonry arches are a fundamental component of historical structures. The assessment of the vulnerability ofthese heritage constructions to seismic loading requires reliable and efficient numerical models. Discrete element models are an alternative to finite element models, being particularly effective in modelling collapse mechanisms created by shearing and separation of the units along the joints. Discrete element codes typically rely on explicit methods of integration of the equations of motion for dynamic analysis, which may require large run times when the recommended stiffness-proportional component of Rayleigh damping is applied. A novel approach is proposed using an alternative damping model, Maxwell damping, which involves placing multiple spring-dashpot elements in the joints, in parallel with the standard stiffness springs. This damping model is tested in the dynamic analysis of masonry arches, under pulse and earthquake loading. The results obtained in this early investigation show a good performance in the simulation of collapse under dynamic loads, in general agreement with the analyses conducted with classical stiffness-proportional damping, but reducing significantly the computational effort.

Rigid particle models based on the discrete element method (DEM) have been adopted to model creep, fracture, and the viscoelastic behaviour of asphalt mixtures considering an irregular micro-structure and particle contacts. Within a DEM framework, the Burgers contact model, which is known to have a narrow frequency and temperature range, is usually adopted to model viscoelastic properties. In this study, a new explicit three-dimensional generalised Kelvin (GK) contact model formulation for the DEM model is proposed for asphalt materials. The model is implemented following two different methodologies (GK and GK). The models are validated in uniaxial tension-compression sinusoidal tests for predicting the dynamic modulus () and phase angle (

Encapsulated rejuvenators embedded in asphalt mixtures are a promising technology toextend the service life of asphalt pavements. However, their effects on the asphalt mixture

The structural rehabilitation of historic/traditional rubble masonry wall constructionsrequires consolidation and retrofitting solutions to be employed in order to withstand dynamic loads,high vertical loads, and differential settlements. One of these strengthening techniques is basedon the use of steel bar connectors perpendicular to the wall, considered individually or integratedinto more complex strengthening techniques. The aim of this study is to evaluate numerically thestrengthening effect of transverse steel connectors on rubble masonry walls. With this purpose, a 2Dparticle-reinforced model (2D-PMR) was devised and applied to model uniaxial compression tests.The results presented show that predictions calculated using the proposed 2D-PMR model are veryclose to known experimental results, particularly in the corresponding failure modes, the increase ofthe maximum uniaxial compression value, and ductility. Parametric studies are also conducted byvarying the diameter of the steel bars and the level of strengthening to assess the influence of thebar-bond effect and lateral plates. The presented parametric numerical studies show that (i) a two-level strengthening solution guarantees a similar response to the three-level strengthening solutionadopted in the experiments; (ii) it is not relevant to apply a grout injection during the applicationprocess of the steel connectors if lateral plates are adopted; and (iii) the 2D-PMR model can be usedin the definition of the steel bar diameter and properties; as shown, a smaller (8 mm) bar diameterpredicts a similar strengthening effect to the (12 mm) bar size adopted in the experiments. Given theperformance of the proposed 2D-PMR model, further work is underway that will allow the 2D-PMRmodel to numerically assess other reinforcement techniques, namely, reinforced micro-concrete layersand textile reinforced mortar.

This study highlights the continued need for numerical simulation methods to predict the earthquakeresponse and damage of masonry mosques, despite recent advances in research. TheKamanl

Circular/spherical rigid particle models that were initially applied to rock fracture studieswere not able to match the ratio of the compressive strength to tensile strength that occurs in rock.In addition, the predicted macroscopic friction angle was much lower than the known hard rockexperimental values. Several enhancements have been proposed to address these issues, namelythe use of a clumped particle logic or the adoption of polygonal/polyhedral grain structures, eitherrigid or flexible. In this work, a flexible 2D DEM based particle model (PM) that allows deformableparticles to interact in a simplified way is presented. The proposed flexible PM model keeps thecontact interaction simplicity and the reduced computational costs characteristic of circular rigidparticle models. The PM model is tested using biaxial tests and Brazilian tests. A discussion re-garding the influence of the grain deformability on the macroscopic elastic and strength response ispresented. It is shown that, when compared with a rigid model, the proposed flexible PM modelpredicts more reasonable indirect tensile strength to direct tensile strength ratio and requires asmaller value of contact fracture energy to give a good agreement with known experimental data.It is also shown that the proposed flexible PM model can predict a behaviour similar to that ob-tained using a flexible PM model through inner particle discretization that is more computationallydemanding.

This paper presents a study, which describes the influence of the dynamic behaviour of the intake tower on the experimental results obtained from operational modal analysis of Cabril dam. A 3D finite element model, for the intake tower of Cabril dam, was developed in order to study the dynamic behaviour of this neighbour structure of the dam. The main dynamic parameters computed and evaluated experimentally for this structure are summarized and discussed, to understand how they can interfere in the modal identification of Cabril dam.

The paper aims at presenting some achievements of joint statistics. The different statistical distributions used for the description of the main parameters of the joint sets (attitude, intensity, area, and aperture) are introduced. For the attitude, a comparison of the existing distribution functions is made. For the intensity, the formulas for its determination are given, the applicable statistical models are presented, and the Poisson model for the occurrence of the discontinuities in rocks is discussed in depth. The statistical models for the distribution of the volume of the blocks of a rock mass are introduced. For the area, again, the formulas for its determination are given, and the applicable statistical models presented. Finally, the distribution function for the aperture is referred to, as well as a note on the roughness and waviness.

A libertação do estado de tensão inicial nos maciços rochosos é a principal acção a considerar em escavações subterrâneas. Como o estado de tensão é muito influenciado pela topografia e por condições geológicas particulares de cada local, a sua determinação a partir de ensaios de campo necessita de uma abordagem particular que, tendo em conta a natureza pontual dos ensaios e a sua variabilidade, permita estimar o estado de tensão global no maciço. Apresentam-se os ensaios realizados para o projecto de uma central subterrânea, com destaque para a modelação numérica que permitiu integrar os resultados dos ensaios e determinar o estado de tensão global mais provável. Os modelos usados permitiram considerar no estado de tensão inicial o efeito erosivo do rio ao escavar o vale e da abertura das galerias onde os ensaios foram executados.

This paper deals with issues related to the evaluation of design parameters from some types of in situ and laboratory tests performed, during the geotechnical investigations, to characterize the most relevant geotechnical properties of the rock mass and also the actions. Some considerations regarding safety evaluation and limit state design are presented. Several types of Rock Mechanics tests are introduced in some detail, and a few application examples covering different Rock Engineering projects are presented to show how test results can be analysed to determine their values to be used in the design. The following examples are shown: triaxial tests to determine the strength of the intact rock, a joint network study for a dam foundation, laboratory shear tests to assess the shear strength of rock joints, flat jack and overcoring tests to estimate the in situ state of stress for an underground cavern, and borehole dilatometer and large flat jack tests to evaluate the deformability of a concrete dam foundation.

The paper presents a description of the Picote II site, the objectives of the study that was carried out to assess the in situ state of stress in the rock mass, details of the testing programme and the methodology used for its interpretation. An overcoring testing programme was performed at the design stage, and a specific methodology was developed for the global interpretation of the test results, making use of a numerical model and considering the effect of the existing canyon on the stress field. This enabled to make recommendations regarding the initial stress field to consider in the design of the powerhouse cavern.Owing to the scarce information obtained at the design stage and to the high values of the calculated horizontal stresses, it was decided to perform additional stress measurement tests, using small flat jacks, once construction started and excavation of the adits reached the proximity of the underground powerhouse. Numerical simulations were also done for its interpretation and they confirmed the stress levels obtained at the design stage. The monitoring scheme implemented in the powerhouse cavern includes instrumentation to measure stress changes, which will occur during the excavation. Finally, the significance of the state of stress assessment to the powerhouse design and to the interpretation of monitoring data collected during construction is discussed.

O Aqueduto das Águas Livres, localizado em Lisboa, hoje desactivado, entrou em funcionamento em 1748. Construído em alvenaria de pedra e tendo uma extensão de 14 km desde a nascente principal, é ainda constituído por diversos aquedutos subsidiários e de distribuição,com um total de 58 km de extensão.Num dos muitos canais subterrâneos existentes está localizada uma abóbada que permite a intersecção de dois alinhamento de túneis. Esta abóbada encontra-se sobre uma importante artéria da cidade de Lisboa com um trânsito automóvel bastante intenso.O estado de conservação da abóbada tem suscitado interrogações quanto à sua capacidade resistente, verificando-se recentemente o desprendimento de um bloco de alvenaria e o deslizamento parcial de outros, o que motivou uma medida de segurança imediata que passou pelo total escoramento da estrutura.Procedeu-se a análise estrutural da abóbada de alvenaria através do 3DEC. Esta aplicação baseia-se no Método dos Elementos Discretos (MED) e tem vindo a ser utilizada, com crescente interesse, no estudo das estruturas de alvenaria.O presente artigo aborda alguns aspectos relacionados com o MED, descreve os procedimentos adoptados para execução do modelo e apresenta resultados quanto a capacidade resistente. A parte final é dedicada avaliação dos resultados e apresentação de soluções para a sua reabilitação e reforço.

Neste trabalho apresenta-se um modelo tridimensional de elementos discretos paraanálise do comportamento dinâmico da barragem do Cabril tendo em conta o efeito das juntas decontracção. Os resultados são comparados com os de um modelo de elementos finitostridimensionais na hipótese de continuidade. O estudo da barragem é efectuado para diferentescotas de água na albufeira, simulando-se o efeito das pressões hidrodinâmicas com base nahipótese de massas de água associadas, proposta por Westergaard. A influência do nível da águana resposta dinâmica do conjunto é estudada com base na análise das variações das frequênciaspróprias comparando-se resultados numéricos e experimentais.

Apresentam-se os resultados do estudo, em modelo numérico, do comportamento sísmico da barragem da Chicamba, em Moçambique. Foram realizados cálculos em regime elástico e cálculos não lineares tendo em consideração o comportamento das juntas verticais de contracção das abóbadas. Os resultados da análise permitiram avaliar as condições de segurança da obra para acções sísmicas.

Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.

N/A

This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.

N/A

Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.

This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.

Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto MEBAD do P2I/LNEC 2013-2020, no período 2016-2023. Os resultados da atividade são analisados e avaliados, em face dos objetivos previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

In this work we present the version 1.0 of the GDams2D 1.0 program developed for 2D analysis of gravity dams using the finite element method. This initial version of the program is prepared to analyze the structural behavior of gravity dams for static loads, considering linear-elastic behavior, and using Lagrange finite elements of 4 sides, with 9 nodal points. The GDams2D 1.0 program, developed in MATLAB, includes a module for automatic generation of meshes with a great level of refinement (generated from coarse meshes of quadrilaterals, with 4 nodal points at the vertices) and is designed for easy adaptation to non-linear analyzes, using stress-transfer modules such as those recently developed for the DamSlide3D and DamDamage3D programs. After a brief reference to the fundamentals of solid mechanics and to the simplified hypotheses of plane elasticity, the Fundamentals of the Finite Element Method (FEM) are presented, referring in particular the formulation of the four-node, linear and isoparametric, finite element (FE4nos), with two translation d.o.f per node, and the quadrangular FEs of 9 nodes (FE9nos) used in GDams2D 1.0. Based on some examples of application to simple 2D structures whose response is knownanalytically, the advantages of FEs are emphasized in relation to FE4nos and the verification and operability of GDams2D 1.0 is made using various discretizations. Finally, the case of a gravity dam (25 m high) is presented. The dam

The main objective of this work is the development and presentation of a three-dimensional finite element program, DamSlide3D, to study the behavior of gravity dams for scenarios of sliding through the dam-foundation interface. The DamSlide3D, developed using MATLAB, includes cube-type finite elements with 20 nodal points ("serendipity") and finite interface elements with 16 nodal points (joint elements). Initially, we present the fundamental equations of Solid Mechanics, referring to the main simplified hypotheses considered in the computationally implemented formulation, which is presented mathematically as a problem of boundary values using a displacement formulation. For the structure body and for the foundation, the hypothesis of isotropic materials with linear elastic behavior is assumed and for the interfaces the hypothesis of non-linear behavior is considered using the Mohr- Coulomb criterion. The DamSlide3D input data is provided in an excel file and includes structure geometry data, material properties, support conditions and load parameters. As output, the program graphically displays the stress field (principal stresses) and the displacement field (deformed structure). The program was verified throughout three numerical tests with known theoretical solutions. In these tests a simple structure was used, composed by a column discretized in 3DFE. At the contact surface between the column and the base (horizontal surface) it was considered an interface discretized using joint finite elements. A plane surface that crosses the column with a given slope is also considered, discretized using the same type of joint finite elements. In the first test, the field of elastic stresses at the base, due to self-weight (SW) and hydrostatic pressure (HP), was compared with the theoretical results. In the second test the nonlinear column response was studied for different values of thefriction angle at the inclined interface (in this test the structure is only submitted to SW). In the third test, for the main SW + HP loads, the stability of the column is studied for a variation of the friction angle, and for a variation of the water level. In these three numerical tests the results were always consistent with the theoretical solutions. Finally, as an example of application, a gravity dam structural behavior was analyzed considering the non-linear behavior in the dam-foundation interface. The dam was subjected to self-weight and hydrostatic pressure. A parametric study was developed in order to study the dam stability for differentvalues of water level and friction angle.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto CoMatFail até ao final de 2017. É feita a apreciação da atividade desenvolvida, nomeadamente quanto ao grau de cumprimento do plano de trabalhos, bem como dos objetivos específicos e dos indicadores de desempenho propostos na ficha de projeto. São ainda referidas as aplicações dos resultados da investigação em trabalhos contratados ao LNEC e as candidaturas a financiamento externo desenvolvidas no âmbito do projeto. Inclui-se em anexo a ficha do projeto atualizada, que contempla a revisão do plano de trabalhos.

Neste relatório apresenta-se de forma sucinta a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposta uma revisão do plano de atividades para os próximos três anos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposto um prolongamento do projeto até ao final de 2018.

This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venant’s expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.

This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.

O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).

Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.

Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.

In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.