Publicações

This study proposes an alternative approach to modeling the failure mechanisms of brickwork assemblages under combined shear

The Western Anatolia Region of Turkey is an important region of high seismic activity.The active dynamics of the region are shaped by a compression and expansion mechanism. This activemechanism is still ongoing and causes strong seismic activity in the region. The Frontinus Gate is amonument in the Roman city of Hierapolis of Phrygia located in southwestern Anatolia. The aim ofthis study is to investigate the seismic behavior of this stone masonry structure using discrete elementmodeling. For this purpose, nonlinear dynamic analyses were performed to simulate the structuralresponse of the gate under seismic excitation. Deformation, damage, and failure patterns induced inthe masonry gate for di erent levels of seismic action are evaluated and discussed. An earthquakewith a return period of 475 years is expected to cause some damage, but no collapse, while for areturn period of 2475 years, the models indicate collapse of the monument.

In this paper three historical masonry minarets in Istanbul, Turkey, are assessed for thedependency between the input harmonic motion and structural response parameters. Theirheights are 40, 73 and 74 m, while the slenderness is 12, 6 and 12, respectively. The discreteelement method is used in dynamic nonlinear analyses. Models were calibrated withmeasured natural frequencies. A series of sine-wave excitations is created for different frequency-amplitude pairs varying between 0.4 and 10 Hz, and between 0.1 and 1 m/s. Fromthe results of dynamic simulations, a general trend was observed for masonry minarets.Especially, slenderness and wall thickness play an important role on their dynamic responseand damage pattern. Dynamic behavior of these minarets cannot reliably be estimated bystatic non-linear analysis. Two engineering demand parameters (EDPs) are defined to characterizethe displacement of the minaret top and the inter-ring shear displacements alongthe minaret body. Damage performance criteria for minarets are proposed based on fourdamage states and tentative limit values are given. We were able to identify the occurrenceof those limit states as a function of frequency and amplitude of sinusoidal input motion.

This study presents a numerical investigation on the fracture mechanism of tension stiffening phenomenon in reinforced concrete members. A novel approach using the discrete element method (DEM) is proposed, where three-dimensional randomly generated distinct polyhedral blocks are used, representing concrete and one-dimensional truss elements are utilized, representing steel reinforcements. Thus, an explicit representation of reinforced concrete members is achieved, and the mechanical behavior of the system is solved by integrating the equations of motion for each block using the central difference algorithm. The inter-block interactions are taken into consideration at each contact point with springs and cohesive frictionalelements. Once the applied modeling strategy is validated, based on previously published experimental findings, a sensitivity analysis is performed for bond stiffness, cohesion strength, and the number of truss elements. Hence, valuable inferences are made regarding discontinuum analysis of reinforced concrete members, including concrete

Nowadays, the management and safety control of large dams is generally based on automatic monitoring, including the socalledseismic and structural health monitoring systems (SSHM), using the latest technology for automatic data measurement,acquisition and transmission. These systems should include software for automatic management and analysis of continuousmonitoring data and software for numerical simulation of the dam dynamic behavior using 3D finite element models. Thissoftware should be designed to provide useful and reliable information to meet the needs and expectations of stakeholders,and to support the studies of researchers and engineers responsible for structural health monitoring. This paper is focusedon the experience gathered from the SSHM system of Cabril dam, a 132 m high-arch dam, in Portugal, that has been undercontinuous dynamic monitoring since 2008. The importance of the software specifically developed for automatic modalidentification, automatic detection of seismic vibrations (distinct from vibrations due to the operation of discharge gates andpower groups), and automatic comparison between experimental data and computed results from a reference finite elementmodel of the dam-reservoir-foundation system, is highlighted. This software includes: (1) the generation of graphics withthe evolution of the identified natural frequencies over time and the comparison with calculated frequencies using differenthypothesis for concrete damage evolution; and (2) a service to automatically send emails summarizing key dynamic monitoringresults to stakeholders to provide the necessary support for informed management and engineering decision making.The main results from SSHM of Cabril dam are presented, namely regarding the evolution of modal parameter over time,considering the influence of water level variations, and the measured response during an earthquake event.

In this study, a novel computational modeling strategy is proposed to estimate the lateral load capacity andbehavior of unreinforced masonry (URM) structures. All commonly noted failure mechanisms are captured viathe proposed modeling strategy using the discrete element method (DEM) in three-dimensions (3D). Masonrywalls are represented as a system of elastic discrete blocks, where the nodal velocities are evaluated by integrating the equations of motion using the central difference method. Then, the mechanical interactions among adjacent blocks are examined utilizing the relative contact displacements and employed in the contact stress calculation. Through this research, a new stress-displacement contact constitutive model is considered and implemented in the commercial software 3DEC, which includes softening stress-displacement behavior for tension, shear, and compression along with the fracture energy concept. The results of the discontinuum models are validated on small- and large-scale experimental studies available in the literature with good agreement. Furthermore, important inferences are made regarding the effect of block size, the number of contact points, and contact stiffness values for robust and accurate simulations of masonry walls.

De acordo com a legislação portuguesa e tendo em consideração o risco sísmico da zona de construção das barragens é obrigatório a implementação de um Sistema de Observação Sísmica (SOS), incorporando instrumentação para caracterizar a ação sísmica induzida nas obras e a respetiva resposta estrutural. Em complemento, têm sido instalados Sistema de Monitoramento Dinâmico Contínuo (SMDC). O SOS permite não apenas a caracterização da ação sísmica, mas também a sua propagação ao longo do maciço rochoso, bem como a resposta estrutural da barragem. O SMDC visa identificar as características dinâmicas da barragem e sua evolução ao longo do tempo, considerando a variação das condições ambientais e operacionais, bem como a possível evolução das propriedades mecânicas dos materiais. Os processamentos são efetuados automaticamente incluindo a caracterização do nível de aceleração e a identificação dos parâmetros modais da barragem. Os valores obtidos pelo processamento automático são armazenados em base de dados, sendo enviados alertas quando são atingidos os patamares de alarme previamente definidos.Os resultados provenientes destes sistemas são comparados com os resultados de modelos numéricos sofisticados, calibrados com o recurso a ensaios experimentais de caraterização dinâmica realizados na obra durante a fase de primeiro enchimento.A combinação da monitorização dinâmica com os modelos numéricos é uma ferramenta fundamental no controlo de segurança estrutural e gestão de risco das barragens.

Today, there are several computational models to predict the mechanical behaviour of masonry structures subjected to external loading. Such models require the input of material parameters to describe the mechanical behaviour and strength of masonry constructions. Although such masonry materialparameters are characterised by stochastic

Nonhomogeneous material characteristics of masonry lead to complex fracture mechanisms,which require substantial analysis regarding the influence of masonry constituents. In this context, thisstudy presents a discontinuum modeling strategy, based on the discrete element method, developed toinvestigate the tensile fracture mechanism of masonry wallettes parallel to the bed joints consideringthe inherent variation in the material properties. The applied numerical approach utilizes polyhedralblocks to represent masonry and integrate the equations of motion explicitly to compute nodalvelocities for each block in the system. The mechanical interaction between the adjacent blocks iscomputed at the active contact points, where the contact stresses are calculated and updated basedon the implemented contact constitutive models. In this research, di erent fracture mechanisms ofmasonry wallettes under tension are explored developing at the unit

During the last decade, many vibration-based structural health monitoring systems have been successfully implementedin different structures such as bridges, towers, stadia and wind turbines, with the aim of studying thestructure dynamics and its evolution over time, eventually detecting the occurrence of novel structural behaviourthat may indicate the presence of damage.Such vibration-based monitoring systems generally rely on the identification of modal properties, which arethen used as monitoring features. Therefore, from operational modal analysis to the tracking of those featuresand finally to data normalization, many processing steps occur that depend on the accuracy of the identifiedmodal properties. Thus, the estimation of the uncertainties associated with the identified modal properties increasesthe robustness of this process.In this context, data obtained from the continuous dynamic monitoring of a concrete arch dam has been usedto evaluate the gains of quantifying the uncertainties of modal properties, evaluating in particular the effect oftaking these uncertainties into consideration when performing automated operational modal analysis, modaltracking and data normalization. Nevertheless, it is observed that the most significant gains of consideringestimates uncertainties occur when these quantities are used for removing outliers during modal tracking.

Dam Safety Control has been at the front line of technology adoption in what concerns dataacquisition. However, it does not take full advantage of the latest advancements when it comes toin-situ, real-time, information visualization. This work explores the application of Augmented Realityto the inspection and monitoring of large Civil Engineering structures, namely concrete dams. Theproposed approach focuses on offering new visualization possibilities, that are not accessiblethrough traditional means, to Dam Safety Control. In that scope, it depicts the specification anddevelopment of a proof-of-concept prototype that allows the monitoring of relevant structural-relatedinformation in an Augmented Reality environment. In particular, it offers an easy and straightforwardway for Civil Engineers and Observation Technicians a mean to access data from the network ofsensors situated in the downstream face and the interior of the structure. Besides providinginsightful information on the current status, it allows exploring the evolution in time of valuesregistered in each sensor. A preliminary study aimed at validating the proposed approach showsthat Augmented Reality technologies can be used efficiently in Dam Safety Control.

A barragem da Bemposta, no trecho internacional do rio Douro, foi construída entre 1960 e 1964. Destina?se à produção de energia, permitindo ainda alguma regularização de caudais. Trata?se de uma barragem em arco?gravidade de betão, aligeirada com um grande vazamento junto à fundação. É definida em planta por arcos circulares e tem cerca de 87 m de altura máxima acima da fundação. O betão da barragem está afetado por reações expansivas, do tipo álcalis?sílica, de moderada magnitude, pelo que os seus efeitos estruturais aparentes são pouco significativos. Para interpretação do comportamento observado da barragem e dos efeitos das reações expansivas, foi elaborado um modelo estrutural que considerou a evolução no tempo das principais ações (pressão hidrostática, variações de temperatura e expansões) e das propriedades do betão. As variações de temperatura no corpo da barragem foram calculadas com um modelo térmico que teve em consideração as temperaturas do ar e da água nas superfícies exteriores da barragem e os efeitos da radiação solar. O modelo estrutural foi analisado em regime viscoelástico, para ter em consideração a fluência e a relaxação do betão. Foi obtido um ajuste notável entre os resultados da observação e das modelações térmica e estrutural. Os resultados evidenciam que os efeitos das expansões são já dominantes no comportamento da obra, em termos de deslocamentos horizontais e verticais e de tensões.

According to the general guidelines of the International Commission on Large Dams (ICOLD) regarding structural safety and health monitoring, the performance of dams under operational/ambient vibrations and during seismic events must be evaluated. This is particularly important considering that dams are civil engineering structures of great relevance for populations which entail a high potential risk1. Therefore, Seismic and Structural Health Monitoring (SSHM) is a topic that has gained importance and thus the installation of monitoring systems for continuously measuring vibrations has been proposed for most of the new large dams, to evaluate their behaviour since the early stages of their service life, and for some of the older dams, built several decades ago, in which deterioration problems (e.g. swelling reactions) may have evolved over the years.In this scope, the present paper focuses on studying the dynamic behaviour of large dams over time, including identification of modal parameters (natural frequencies, modal damping ratios and mode shapes) and seismic response analysis, based on measured accelerations time histories. A comparison between experimental results obtained from continuous vibrations monitoring data and numerical modelling results from 3DFE models is presented. The goal is to emphasize the interest of the combined use of recorded data from continuous dynamic monitoring systems and of numerical modelling software for SSHM of dams.The case studies are two large arch dams that have been under continuous dynamic monitoring over the last ten years: Cabril dam (132 m high), the highest Portuguese dam, and Cahora Bassa dam (170 m high), located in Mozambique, one of the highest dams in Africa. The monitoring systems installed in both dams have similar schemes and were designed to continuously record acceleration time series in several points located in the dam body (upper part) and near the dam-foundation interface, using uniaxial and triaxial accelerometers. Specific software was developed for analysing monitoring data, including automatic modal identification and automatic detection of seismic events. The main experimental outputs are presented for Cabril dam and Cahora Bassa dam, with emphasis on the evolution of natural frequencies over time, on vibration mode shapes for various water levels, and, finally, on the measured response in accelerations during seismic events. The numerical results are computed using a 3DFEM program, based on a solid-fluid coupled formulation to simulate the dam-reservoir-foundation system, considering the dam-water dynamic interaction and the propagation of pressure waves throughout the reservoir.

This paper presents a study on the non-linear seismic response of Cabril arch dam (Portugal), for a load combination including the dam

The numerical analysis of concrete dam failure scenarios requires computational tools that candeal with the formation, propagation and localization of cracks and their effects on the overall dambehaviour. It is well known that assemblies of discrete part icles connected through simpleinteraction laws can capture the global behaviour of quasi-brittle macro-material, like concrete.In this work a particle model based on the discrete element method is used. Due to computationalrestrictions some simplifications are adopted: i) a finite element model is adopted in thefoundation and in the dam zone where an elastic behaviour is expected; ii) the adopted particlesize is higher than the maximum aggregate size of dam concrete. In order to further reducecomputational times a hybrid discrete/finite model is proposed that replaces the stiffness of thefinite elements where nonlinear behaviour is expected by a discrete particle assembly in itsinterior.The hybrid discrete/finite model is validated for several case studies. The results are comparedwith those obtained with a finite element based two scalar damage model. The results show theapplicability of particle models to the study of failure scenarios of concrete dams, including itsinitial elastic response, even when the adopted aggregate structure is much larger in size than theadopted concrete aggregate.

This paper presents the relevant results of the monitoring data analysis of the Chicamba dam(Mozambique), which confirmed the existence of an ongoing concrete swelling process in the dam

This paper presents a study on the seismic response of the 132 m high Cabril arch dam, for an earthquake measured in-situ with the installed Seismic and Structural Health Monitoring system (in operation since 2008). The measured acceleration time histories are compared with results from finite element analysis in various positions in the dam body, using the seismic accelerations recorded at the dam-rock interface as inputs. The numerical simulations are conducted using two programs: i) DamDySSA4.0, a 3D finite element program develop in LNEC for dynamic analysis of arch dams

In the last decade Portugal made a significant set of investments in new hydroelectric projects under the National Dams Program with High Hydroelectric Potential. EDP Produção SA, a company of EDP - Energias de Portugal Group, played a fundamental role in the construction of these projects, in which new dams and reservoirs of significant dimensions are integrated.According to Portuguese legislation, with relevance to the RSB-Dam Safety Regulation (Decree-Law no. 21/2018 of 28 March), the DTA-Technical Documents to Support the RSB and taking into account the seismic risk associated with the region where the dams were built, it was recommending the implementation of a set of Seismic Monitoring Systems (SMS) to characterize the seismic actions and the respective structural response, as well as the assessment of the reservoirs induced seismicity.For that, it was necessary, in the design phases, to carry out several studies to define the type of dynamic monitoring systems, especially those related to the seismic monitoring systems (SMS). In their most extensive configuration, these systems, based on triaxial accelerometers sensors, may incorporate remote stations installed along the reservoirs for studying the propagation of seismic actions. For the higher dams, and to ensure a good characterization of the dynamic behaviour, continuous dynamic monitoring system (CDMS) was also installed.This paper presents the main aspects of the legislation, refers the main studies and methodologies that were used, and the general aspects of the regional geological and tectonic framework. Also, is presented several seismic monitoring systems that were implemented by EDP, namely those related to the hydroelectric projects of Baixo Sabor, Foz Tua, Ribeiradio and Alto Ceira II dams.

This paper focuses on the experience gathered from the continuous dynamic monitoring of Cahora Bassa dam, a 170 m high arch dam in Mozambique, over the past decade. The installed Seismic and Structural Health Monitoring system was designed to continuously record acceleration time series in several locations in the dam body (crest gallery) and near the dam-rock interface, under ambient/operational vibrations and during seismic events, using uniaxial and triaxial accelerometers. The system was complemented with the development of software for automatic modal identification and automatic detection of seismic vibrations. The numerical simulations are carried out using a 3D finite element program, based on a solid-fluid coupled formulation to simulate the dam-reservoir-foundation system, considering dam-water dynamic interaction and propagation of pressure waves throughout the reservoir. The main experimental outputs are presented and compared with results from 3D finite element analysis, including the evolution of identified natural frequencies over time, vibration mode shapes for specific water levels, and the dynamic response in accelerations under seismic ground motion.

Neste trabalho efetuam-se estudos de simulação numérica da resposta sísmica de uma grande barragem abóbada, considerando uma dada lei de amortecimento de Rayleigh com vista a analisar a influência da cota da albufeira. A modelação do sistema barragem-fundação-albufeira é efetuada com um modelo coupled, baseado numa formulação em deslocamentos e pressões, que permite simular a interação dinâmica barragem-albufeira considerando a propagação de ondas de pressão na albufeira. A discretização do sistema coupled é efetuada utilizando elementos finitos 3D com 20 nós. A resposta sísmica é calculada por meio de integração direta no domínio do tempo com base no método de Newmark. São apresentados os resultados da análise sísmica de uma barragem com 290 m de altura, utilizando acelerogramas sísmicos em três direções, com aceleração de pico máxima de 0.3g na direção montante-jusante. Nomeadamente, analisam-se os campos de deslocamentos e de tensões no corpo da obra para diferentes cotas de água na albufeira.

Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.

N/A

This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.

N/A

Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.

This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.

Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto MEBAD do P2I/LNEC 2013-2020, no período 2016-2023. Os resultados da atividade são analisados e avaliados, em face dos objetivos previstos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat do P2I/LNEC 2013-2020. Os resultados da atividade desenvolvida são analisados e avaliados em face dos objetivos inicialmente previstos.

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

The main goal of this report is to present DamDamage3D1.0, a 3D finite element-based program for non-linear static analysis of arch dams, developed using MATLAB. The non-linear simulations are performed using a damage law and an iterative numerical method based on the stress-transfer technique, considering the redistribution of unbalanced forces in each iteration due to material damage. The concrete

In this work we present the version 1.0 of the GDams2D 1.0 program developed for 2D analysis of gravity dams using the finite element method. This initial version of the program is prepared to analyze the structural behavior of gravity dams for static loads, considering linear-elastic behavior, and using Lagrange finite elements of 4 sides, with 9 nodal points. The GDams2D 1.0 program, developed in MATLAB, includes a module for automatic generation of meshes with a great level of refinement (generated from coarse meshes of quadrilaterals, with 4 nodal points at the vertices) and is designed for easy adaptation to non-linear analyzes, using stress-transfer modules such as those recently developed for the DamSlide3D and DamDamage3D programs. After a brief reference to the fundamentals of solid mechanics and to the simplified hypotheses of plane elasticity, the Fundamentals of the Finite Element Method (FEM) are presented, referring in particular the formulation of the four-node, linear and isoparametric, finite element (FE4nos), with two translation d.o.f per node, and the quadrangular FEs of 9 nodes (FE9nos) used in GDams2D 1.0. Based on some examples of application to simple 2D structures whose response is knownanalytically, the advantages of FEs are emphasized in relation to FE4nos and the verification and operability of GDams2D 1.0 is made using various discretizations. Finally, the case of a gravity dam (25 m high) is presented. The dam

The main objective of this work is the development and presentation of a three-dimensional finite element program, DamSlide3D, to study the behavior of gravity dams for scenarios of sliding through the dam-foundation interface. The DamSlide3D, developed using MATLAB, includes cube-type finite elements with 20 nodal points ("serendipity") and finite interface elements with 16 nodal points (joint elements). Initially, we present the fundamental equations of Solid Mechanics, referring to the main simplified hypotheses considered in the computationally implemented formulation, which is presented mathematically as a problem of boundary values using a displacement formulation. For the structure body and for the foundation, the hypothesis of isotropic materials with linear elastic behavior is assumed and for the interfaces the hypothesis of non-linear behavior is considered using the Mohr- Coulomb criterion. The DamSlide3D input data is provided in an excel file and includes structure geometry data, material properties, support conditions and load parameters. As output, the program graphically displays the stress field (principal stresses) and the displacement field (deformed structure). The program was verified throughout three numerical tests with known theoretical solutions. In these tests a simple structure was used, composed by a column discretized in 3DFE. At the contact surface between the column and the base (horizontal surface) it was considered an interface discretized using joint finite elements. A plane surface that crosses the column with a given slope is also considered, discretized using the same type of joint finite elements. In the first test, the field of elastic stresses at the base, due to self-weight (SW) and hydrostatic pressure (HP), was compared with the theoretical results. In the second test the nonlinear column response was studied for different values of thefriction angle at the inclined interface (in this test the structure is only submitted to SW). In the third test, for the main SW + HP loads, the stability of the column is studied for a variation of the friction angle, and for a variation of the water level. In these three numerical tests the results were always consistent with the theoretical solutions. Finally, as an example of application, a gravity dam structural behavior was analyzed considering the non-linear behavior in the dam-foundation interface. The dam was subjected to self-weight and hydrostatic pressure. A parametric study was developed in order to study the dam stability for differentvalues of water level and friction angle.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto CoMatFail até ao final de 2017. É feita a apreciação da atividade desenvolvida, nomeadamente quanto ao grau de cumprimento do plano de trabalhos, bem como dos objetivos específicos e dos indicadores de desempenho propostos na ficha de projeto. São ainda referidas as aplicações dos resultados da investigação em trabalhos contratados ao LNEC e as candidaturas a financiamento externo desenvolvidas no âmbito do projeto. Inclui-se em anexo a ficha do projeto atualizada, que contempla a revisão do plano de trabalhos.

Neste relatório apresenta-se de forma sucinta a descrição da atividade de investigação realizada no âmbito do projeto DEMRock6m no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposta uma revisão do plano de atividades para os próximos três anos.

Neste relatório apresenta-se, de forma sucinta, a descrição da atividade de investigação realizada no âmbito do projeto RockGeoStat no período 2016-2017. Os resultados da atividade são analisados e avaliados em face dos objetivos inicialmente previstos, sendo proposto um prolongamento do projeto até ao final de 2018.

This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venant’s expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.

This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.

O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).

Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.

Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.

In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.