Publicações

During the last decade, many vibration-based structural health monitoring systems have been successfully implemented in different structures such as bridges, towers, stadia and wind turbines, with the aim of studying the structure dynamics and its evolution over time, eventually detecting the occurrence of novel structural behaviour that may indicate the presence of damage.Such vibration-based monitoring systems generally rely on the identification of modal properties, which are then used as monitoring features. Therefore, from operational modal analysis to the tracking of those features and finally to data normalization, many processing steps occur that depend on the accuracy of the identified modal properties. Thus, the estimation of the uncertainties associated with the identified modal properties increases the robustness of this process.In this context, data obtained from the continuous dynamic monitoring of a concrete arch dam has been used to evaluate the gains of quantifying the uncertainties of modal properties, evaluating in particular the effect of taking these uncertainties into consideration when performing automated operational modal analysis, modal tracking and data normalization. Nevertheless, it is observed that the most significant gains of considering estimates uncertainties occur when these quantities are used for removing outliers during modal tracking.

Masonry arch bridges form a significant portion of the European transport infrastructure network. Manyof these bridges are relatively old but still in service. Increasing vehicle loads and speeds have highlightedthe need for reliable estimates of their service condition. Past research demonstrated that load-carryingcapacity of a masonry arch bridge is a function of the soil response. However, today, the approaches usedfor the simulation of soil in masonry arch bridges are over-simplistic and most of them do not take intoaccount the soil-structure interaction phenomena. This paper presents a novel modelling approach, basedon the discrete element method, for the simulation of backfill material in masonry arch bridges.According to the method, bricks in the barrel vault are simulated as an assembly of distinct blocks separatedby zero thickness interfaces at each mortar joint. Backfill is represented as an assemblage of denselypacked discrete irregular deformable particles, here called

Discrete element models are a powerful tool for the analysis of masonry, given theirability to represent the discontinuous nature of these structures, and to simulate the most commondeformation and failure modes. In particular, discrete elements allow the assessment of the seismicbehavior of masonry construction, using either pushover analysis or time domain dynamic analysis.The fundamental concepts of discrete elements are concisely presented, stressing the issues relatedto masonry modeling. Methods for generation of block models are discussed, with some examplesfor the case of irregular stone masonry walls. A discrete element analysis of a shaking table testperformed on a traditional stone masonry house is discussed, as a demonstration of the capabilitiesof these models. Practical application issues are examined, namely the computational requirementsfor dynamic analysis.

Earthquakes represent one of the major threats to cultural heritage monuments, such as classical ancient columns.Understanding the behaviour and dynamic response of such historic structures is useful for the assessmentof the conservation and rehabilitation techniques to be used for their preservation. The behaviour of ancientmulti-drum and monolithic columns subjected to dynamic loads is characterized by highly nonlinearity sinceboth rocking and sliding phenomena can occur. Analytical studies of multi-drum columns subjected to dynamicload is extremely complicated, if not impossible to perform. Nowadays, computational methods of analysis canbe used to represent their dynamic response. Using a software based on the Discrete Element Method (DEM) ofanalysis, a typical ancient multi-drum and an equivalent in dimensions monolithic columns subjected to horizontaland combined horizontal and vertical harmonic excitations were modelled to identify the main factorsaffecting their stability. Different acceleration amplitude and frequency input records were applied and their rolein the collapse/deformation mechanism was investigated. From the results analyses it was shown that novelstructural analysis tools that extend traditional methods of structural assessment could allow engineers to understandthe mechanisms that have allowed the surviving structures to avoid structural collapse and destructionduring strong earthquakes.

No 14º Encontro Internacional de Modelação Numérica em Barragens, organizado pela ICOLD, foi proposta a análise numérica de uma barragem de betão em arco localizada na Suécia sujeita a gradientes térmicos significativos ao longo do ano. Neste artigo apresentam-se os resultados numéricos obtidos com basenuma discretização mais refinada do corpo da barragem, quando comparada com o modelo adotado no encontro internacional. Os resultados da análise mecânica realizada com um modelo de fenda discreta são comparados com as observações in situ. Verifica--se que o modelo estrutural mais refinado permite obter resultados mais próximos dos observados, nomeadamente a distribuição de fendilhação no paramento de jusante e o campo de deslocamentos. Analisa-se ainda o efeito das armaduras distribuídas colocadas juntoao paramento de montante e ao paramento de jusante no controlo de deformação e fendilhação.

This paper focuses on studying the dynamic behaviour of large dams over time, including identification of modal parameters (naturalfrequencies, modal damping ratios and mode shapes) and seismic response analysis, based on measured acceleration time histories.A comparison between experimental results obtained from continuous vibration monitoring data and numerical modelling results from 3DFE models is presented. The aim is to emphasize the interest of combining the use of recorded data from continuous dynamic monitoringsystems and of numerical modelling software for seismic and structural health monitoring of dams.

The seismic response of a 290 m high arch dam, located in ahigh seismicity zone in China, is studied in this paper. The goal isto evaluate the influence of the reservoir water level on the dam

Over the last 50 years, a significant amount of effort has been taken to develop numerical approaches andtools for the structural analysis of masonry. These range from considering masonry as an anisotropic continuum(macro-models) to the more detailed ones considering masonry as an assemblage of units andjoints (micro-models). In this paper, a detailed micro-modelling approach for the analysis of masonrycouplets and prisms is proposed. The approach represents masonry units and mortar joints as an assemblageof densely packed discrete irregular deformable particles bonded together by zero thickness interfacelaws. The mechanical properties (here referred to as micro-properties) of irregular particles andcontacts are responsible for the mechanical behaviour of masonry. In addition, the approach allows failureto occur either at the brick, mortar and/or brick/mortar interface. A series of computational modelswere developed and their results are compared against small-scale experimental findings. A good agreementbetween the experimental and the numerical results was obtained which demonstrates the hugepotential of the modelling approach proposed. The significant advantage of this approach is to modelcracking as a real discontinuity among particles and not as a modification in the material properties.In addition, reliable prediction of masonry strength can allow one to reduce the costly and timely experimentaltesting and avoid the reliance on conservative empirical formulas.

Pretende-se com este trabalho estudar o efeito das vibrações provocadas pelas explosões devidas a desmontes no comportamento da barragem de betão e respetiva fundação, avaliando a sua seguran-ça estrutural através de um modelo numérico híbrido descontínuo de elementos discretos e elemen-tos finitos recorrendo ao 3DEC.Apresentam-se os resultados do modelo numérico comparando-o com as medições de velocidades efetuadas no decorrer das obras envolvendo desmontes a fogo, sendo posteriormente analisado os efeitos na barragem. O presente trabalho deu origem ao desenvolvimento de um modelo numérico capaz de representar a resposta da estrutura às vibrações, minimizando a subjetividade da classifica-ção do seu grau de resistência.

O dimensionamento de barragens, de acordo com a regulamentação portuguesa, engloba a verifica-ção da segurança da obra para diversos cenários de rotura. Nesta comunicação, apresenta-se um exemplo de aplicação conjunta de métodos experimentais e numéricos para: i) determinação do coe-ficiente de segurança de uma barragem abóbada num cenário de rotura por deslizamento de parte do maciço de fundação para ações estáticas, ii) o estudo do comportamento dinâmico até à rotura uma barragem de gravidade por deslizamento ao longo da fundação. Os resultados experimentais foram comparados com os obtidos a partir de modelações matemáticas devidamente calibradas.

Dam Safety Control has been at the front line of technology adoption in what concerns dataacquisition. However, it does not take full advantage of the latest advancements when it comes toin-situ, real-time, information visualization. This work explores the application of Augmented Realityto the inspection and monitoring of large Civil Engineering structures, namely concrete dams. Theproposed approach focuses on offering new visualization possibilities, that are not accessiblethrough traditional means, to Dam Safety Control. In that scope, it depicts the specification anddevelopment of a proof-of-concept prototype that allows the monitoring of relevant structural-relatedinformation in an Augmented Reality environment. In particular, it offers an easy and straightforwardway for Civil Engineers and Observation Technicians a mean to access data from the network ofsensors situated in the downstream face and the interior of the structure. Besides providinginsightful information on the current status, it allows exploring the evolution in time of valuesregistered in each sensor. A preliminary study aimed at validating the proposed approach showsthat Augmented Reality technologies can be used efficiently in Dam Safety Control.

A barragem da Bemposta, no trecho internacional do rio Douro, foi construída entre 1960 e 1964. Destina?se à produção de energia, permitindo ainda alguma regularização de caudais. Trata?se de uma barragem em arco?gravidade de betão, aligeirada com um grande vazamento junto à fundação. É definida em planta por arcos circulares e tem cerca de 87 m de altura máxima acima da fundação. O betão da barragem está afetado por reações expansivas, do tipo álcalis?sílica, de moderada magnitude, pelo que os seus efeitos estruturais aparentes são pouco significativos. Para interpretação do comportamento observado da barragem e dos efeitos das reações expansivas, foi elaborado um modelo estrutural que considerou a evolução no tempo das principais ações (pressão hidrostática, variações de temperatura e expansões) e das propriedades do betão. As variações de temperatura no corpo da barragem foram calculadas com um modelo térmico que teve em consideração as temperaturas do ar e da água nas superfícies exteriores da barragem e os efeitos da radiação solar. O modelo estrutural foi analisado em regime viscoelástico, para ter em consideração a fluência e a relaxação do betão. Foi obtido um ajuste notável entre os resultados da observação e das modelações térmica e estrutural. Os resultados evidenciam que os efeitos das expansões são já dominantes no comportamento da obra, em termos de deslocamentos horizontais e verticais e de tensões.

According to the general guidelines of the International Commission on Large Dams (ICOLD) regarding structural safety and health monitoring, the performance of dams under operational/ambient vibrations and during seismic events must be evaluated. This is particularly important considering that dams are civil engineering structures of great relevance for populations which entail a high potential risk1. Therefore, Seismic and Structural Health Monitoring (SSHM) is a topic that has gained importance and thus the installation of monitoring systems for continuously measuring vibrations has been proposed for most of the new large dams, to evaluate their behaviour since the early stages of their service life, and for some of the older dams, built several decades ago, in which deterioration problems (e.g. swelling reactions) may have evolved over the years.In this scope, the present paper focuses on studying the dynamic behaviour of large dams over time, including identification of modal parameters (natural frequencies, modal damping ratios and mode shapes) and seismic response analysis, based on measured accelerations time histories. A comparison between experimental results obtained from continuous vibrations monitoring data and numerical modelling results from 3DFE models is presented. The goal is to emphasize the interest of the combined use of recorded data from continuous dynamic monitoring systems and of numerical modelling software for SSHM of dams.The case studies are two large arch dams that have been under continuous dynamic monitoring over the last ten years: Cabril dam (132 m high), the highest Portuguese dam, and Cahora Bassa dam (170 m high), located in Mozambique, one of the highest dams in Africa. The monitoring systems installed in both dams have similar schemes and were designed to continuously record acceleration time series in several points located in the dam body (upper part) and near the dam-foundation interface, using uniaxial and triaxial accelerometers. Specific software was developed for analysing monitoring data, including automatic modal identification and automatic detection of seismic events. The main experimental outputs are presented for Cabril dam and Cahora Bassa dam, with emphasis on the evolution of natural frequencies over time, on vibration mode shapes for various water levels, and, finally, on the measured response in accelerations during seismic events. The numerical results are computed using a 3DFEM program, based on a solid-fluid coupled formulation to simulate the dam-reservoir-foundation system, considering the dam-water dynamic interaction and the propagation of pressure waves throughout the reservoir.

This paper presents a study on the non-linear seismic response of Cabril arch dam (Portugal), for a load combination including the dam

The numerical analysis of concrete dam failure scenarios requires computational tools that candeal with the formation, propagation and localization of cracks and their effects on the overall dambehaviour. It is well known that assemblies of discrete part icles connected through simpleinteraction laws can capture the global behaviour of quasi-brittle macro-material, like concrete.In this work a particle model based on the discrete element method is used. Due to computationalrestrictions some simplifications are adopted: i) a finite element model is adopted in thefoundation and in the dam zone where an elastic behaviour is expected; ii) the adopted particlesize is higher than the maximum aggregate size of dam concrete. In order to further reducecomputational times a hybrid discrete/finite model is proposed that replaces the stiffness of thefinite elements where nonlinear behaviour is expected by a discrete particle assembly in itsinterior.The hybrid discrete/finite model is validated for several case studies. The results are comparedwith those obtained with a finite element based two scalar damage model. The results show theapplicability of particle models to the study of failure scenarios of concrete dams, including itsinitial elastic response, even when the adopted aggregate structure is much larger in size than theadopted concrete aggregate.

This paper presents the relevant results of the monitoring data analysis of the Chicamba dam(Mozambique), which confirmed the existence of an ongoing concrete swelling process in the dam

This paper presents a study on the seismic response of the 132 m high Cabril arch dam, for an earthquake measured in-situ with the installed Seismic and Structural Health Monitoring system (in operation since 2008). The measured acceleration time histories are compared with results from finite element analysis in various positions in the dam body, using the seismic accelerations recorded at the dam-rock interface as inputs. The numerical simulations are conducted using two programs: i) DamDySSA4.0, a 3D finite element program develop in LNEC for dynamic analysis of arch dams

In the last decade Portugal made a significant set of investments in new hydroelectric projects under the National Dams Program with High Hydroelectric Potential. EDP Produção SA, a company of EDP - Energias de Portugal Group, played a fundamental role in the construction of these projects, in which new dams and reservoirs of significant dimensions are integrated.According to Portuguese legislation, with relevance to the RSB-Dam Safety Regulation (Decree-Law no. 21/2018 of 28 March), the DTA-Technical Documents to Support the RSB and taking into account the seismic risk associated with the region where the dams were built, it was recommending the implementation of a set of Seismic Monitoring Systems (SMS) to characterize the seismic actions and the respective structural response, as well as the assessment of the reservoirs induced seismicity.For that, it was necessary, in the design phases, to carry out several studies to define the type of dynamic monitoring systems, especially those related to the seismic monitoring systems (SMS). In their most extensive configuration, these systems, based on triaxial accelerometers sensors, may incorporate remote stations installed along the reservoirs for studying the propagation of seismic actions. For the higher dams, and to ensure a good characterization of the dynamic behaviour, continuous dynamic monitoring system (CDMS) was also installed.This paper presents the main aspects of the legislation, refers the main studies and methodologies that were used, and the general aspects of the regional geological and tectonic framework. Also, is presented several seismic monitoring systems that were implemented by EDP, namely those related to the hydroelectric projects of Baixo Sabor, Foz Tua, Ribeiradio and Alto Ceira II dams.

This paper focuses on the experience gathered from the continuous dynamic monitoring of Cahora Bassa dam, a 170 m high arch dam in Mozambique, over the past decade. The installed Seismic and Structural Health Monitoring system was designed to continuously record acceleration time series in several locations in the dam body (crest gallery) and near the dam-rock interface, under ambient/operational vibrations and during seismic events, using uniaxial and triaxial accelerometers. The system was complemented with the development of software for automatic modal identification and automatic detection of seismic vibrations. The numerical simulations are carried out using a 3D finite element program, based on a solid-fluid coupled formulation to simulate the dam-reservoir-foundation system, considering dam-water dynamic interaction and propagation of pressure waves throughout the reservoir. The main experimental outputs are presented and compared with results from 3D finite element analysis, including the evolution of identified natural frequencies over time, vibration mode shapes for specific water levels, and the dynamic response in accelerations under seismic ground motion.

Neste trabalho efetuam-se estudos de simulação numérica da resposta sísmica de uma grande barragem abóbada, considerando uma dada lei de amortecimento de Rayleigh com vista a analisar a influência da cota da albufeira. A modelação do sistema barragem-fundação-albufeira é efetuada com um modelo coupled, baseado numa formulação em deslocamentos e pressões, que permite simular a interação dinâmica barragem-albufeira considerando a propagação de ondas de pressão na albufeira. A discretização do sistema coupled é efetuada utilizando elementos finitos 3D com 20 nós. A resposta sísmica é calculada por meio de integração direta no domínio do tempo com base no método de Newmark. São apresentados os resultados da análise sísmica de uma barragem com 290 m de altura, utilizando acelerogramas sísmicos em três direções, com aceleração de pico máxima de 0.3g na direção montante-jusante. Nomeadamente, analisam-se os campos de deslocamentos e de tensões no corpo da obra para diferentes cotas de água na albufeira.

Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.

N/A

This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.

N/A

Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.

This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.

Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.

Neste trabalho apresenta-se o sistema para monitorização em contínuo do comportamento dinâmico da barragem do Cabril que foi instalado em 2008, pelo LNEC e pela EDP, referindo alguns dos principais resultados que têm sido obtidos a partir da análise dos dados recolhidos, quer sob excitação ambiente/operacional, quer sob ações sísmicas. Salienta-se a importância do desenvolvimento do software para tratamento, análise e gestão automática dos dados e apresentam-se os programas que têm vindo a ser desenvolvidos no LNEC, em MATLAB, para apoio a este tipo de sistemas, nomeadamente programas de identificação modal (Modal_ID2.0 e Modal_ID_Auto2.0) e programas de elementos finitos tridimensionais para análise do comportamento dinâmico de sistemas barragem-fundação-albufeira (DamDySSA2.0).

This document presents the research plan for the doctoral thesis of LNEC's Junior Research Fellow Margarida Espada. This work, to be submitted to the Faculty of Engineering of the University of Porto (FEUP), will be developed in the Modelling and Rock Mechanics Unit of the Concrete Dams Department, and it is part of the on-going P2I research project DEMRock6m. This work aims at developing more efficient methodologies to perform safety studies and seismic analysis of rock engineering structures, based on discrete element models and in the integrated use of probabilistic models for the geometric and shear strength parameters and for the water pressures in rock discontinuities. This will allow a more realistic definition of the rock mass in discrete element models and an adequate identification of the potential failure mechanisms.

Neste relatório é apresentado o método de Euler para calcular as órbitas do sistema n-corpos,por exemplo, o dos planetas do sistema Solar, tendo em conta a propagação das forçasgravíticas entre o Sol e os planetas e entre os planetas entre si. Apenas requer como dadosiniciais uma observação anterior das órbitas em termos de posição e velocidade. A correcçãoda interacção entre planetas não é suavizada, o que se justifica pelos seus valores. A correcçãorelativista é importante.

As equações de Navier-Stokes são equações de derivadas parciais. As incógnitas nocaso de incompressibilidade consistem no campo de velocidades. As pressões numa 1ªaproximação resultam de um equilíbrio estático.A principal causa de problemas relacionados com a solução destas equações é devida àparcela das acelerações convectivas que está na origem da turbulência.Pesando estas equações e integrando duas vezes por partes obtém-se uma forma fracadestas equações.Em problemas 3D as variáveis independentes são 3 espaciais e 1 temporal. Admite-seque o campo de velocidades pode ser desenvolvido em série de distribuições de Delta deDirac espaciais e suas derivadas com coeficientes funções do tempo. Com funções deteste polinomiais obtém-se a formulação distribucional proposta das equações deNavier-Stokes.

N/A

O objectivo deste relatório é o estudo da matemática aplicada à solução de problemasfísicos de propagação de ondas esféricas com operador espacial biharmónico,consideradas quânticas.As técnicas matemáticas usadas incluem a transformada de Laplace da função de ondaf e o cálculo de sua inversa tal como sugerida por Pipes e Harvill.O método matemático usado para descrever as ondas esféricas quânticas é compequenas adaptações o método causal não-linear descrito por Croca.

N/A

N/A

N/A

A análise do comportamento de barragens de betão com base em modelos de elementos finitos tridimensionais exige a definição da discretização a adoptar para o conjunto barragem-fundação, ou barragem-fundação-albufeira. A realização desta tarefa sem o recurso a programas de geração automática é muito dispendiosa pelo que tem vindo a ser desenvolvido no NMMF um módulo computacional para geração automática de malhas de elementos finitos tridimensionais especialmente adaptado para a geração de malhas tridimensionais de barragens abóbada. Inicialmente desenvolvido em FORTRAN, o referido módulo computacional para geração de malhas de elementos finitos tridimensionais tem vindo a ser objecto de diversos melhoramentos, os mais recentes centrados ao nível da interface com o utilizador. Assim, apresenta-se neste relatório o módulo computacional

This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venant’s expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.

This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.

O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).

Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.

Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.

In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.