Publicações

A avaliação do dano causado pela agitação incidente em modelos físicos de quebra mares de taludes pode ser realizada comparando volumes e profundidades erodidas entre levantamentos consecutivos de cada talude.Atualmente, estes levantamentos podem ser realizados de forma não intrusiva, recorrendo a técnicas fotogramétricas, a laser scan ou a sensores de posição baseados na metolodologia Time of Flight (ToF). Dependendo das condições de levantamento e da metodologia de pós-processamento das nuvens de pontos obtidas, estas técnicas permitem obter modelos tridimensionais de superfície, com elevada precisão.Em detalhe, as diferenças de volume entre os levantamentos inicial e

SAFEPORT safety system aims to daily reports to the Sines harbor administration, potential emergency situations regarding ships

Early warning systems are an important tool for local authorities to detect emergency situations in advance and initiate the necessary safety measure. These systems often depend on numerical models to estimate wave overtopping in the affected areas. The SWASH model has shown to deliver good results in recent overtopping studies. The To-SEAlert project has the aim of increasing the efficiency, robustness and reliability of the HIDRALERTA early warning system. This study shows a first intent to implement the SWASH model to simulate wave overtopping for the Ericeira prototype. SWASH was implemented for one breakwater profile used to simulate the overtopping discharge and evaluate the associated risk levels. It was compared to the current approach used in HIDRALERTA, which resorts to a neural network trained with a physical modeling database, NN_OVERTOPPING2. Finally, both approaches were compared with previously analyzed video images of the breakwater. The results showed that SWASH generally overestimates overtopping and is not in good agreement with the video images. NN_OVERTOPPING2 has a better agreement with the video images. A possible reason for the overestimation might be the wave direction, which cannot be included in one-dimensional simulations in SWASH.

Early Warning Systems are crucial disaster-risk-reduction strategies as they allow local authorities to prepare and implement in advance the necessary measures to avoid major destruction and risk for individuals and properties caused by storm events. HIDRALERTA is a forecast, early warning and risk assessment system for port and coastal areas that uses forecasts of sea waves and water levels to evaluate overtopping/flooding events and risks associated with the mooring of ships. The distinguishing feature of this system is that the risk assessment is based on specific parameters related to the actual risk being predicted, such as overtopping discharges, or the ship

In this study, performance of an oscillating water column wave energy converter inserted into a hypothetical composite breakwater with rubble mound foundation located at the southern Brazilian coast is analyzed. The FLUENT® numerical model, which is based on the Reynolds-Averaged Navier-Stokes equations, is used in 2D numerical simulations by adopting the Volume of Fluid method to consider the two-phase flow (water and air). The influence of the rubble mound foundation on the pneumatic power, the run-up/down, the free surface elevation inside the chamber, and the energy balance for different incident waves are investigated. The rubble mound foundation of the composite breakwater slightly affected hydrodynamics; however, it reduced significantly the pneumatic power of the device from 7 to 15% comparing with that obtained to a vertical breakwater founded on an impermeable foundation.

This study aims proposing a novel geometry of the onshore Oscillating Water Column (OWC) device to increase its efficiency. A comparison between standard OWC

Este trabalho descreve a aplicação do sistema SAFEPORT no Porto de Sines, e em particular, o teste de uma das funcionalidades do sistema relacionada com otimização de operações marítimas em ambiente portuário. O SAFEPORT é um sistema de previsão e alerta de perigosassociados a navegação.A aplicação do sistema SAFEPORT permitiu a otimização dos esquemas de amarração de três navios distintos acostados em três terminais do Porto de Sines, sob as condições de agitação marítima provocadas pela tempestade Dora (4 de dezembro de 2020). Foram construídos os modelos dos três navios e analisados vários esquemas de amarração a fim de obter uma solução ótima para cada navio. Este exercício mostrou que o sistema SAFEPORT é uma ferramenta útil para apoio à decisão nos sistemas de amarração dos navios. A configuração dos cabos de amarração tem grande influência no comportamento, e consequentemente na segurança, dos navios amarrados sujeitos a situações de tempestade.

The assessment of damage evolution in scale model tests of rubble-mound breakwaters can be achieved by comparing eroded depths and volumes between consecutive surveys. Aiming to evaluate damage evolution on rubble-mound breakwater, scale model tests were recently conducted on the maritime hydraulic facilities of the National Laboratory for Civil Engineering. This paper focuses on the use of novel, non-intrusive survey methodologies such as the Time of Flight (ToF) principle technique. In this study, damage evaluation is based on the comparison of point clouds obtained before and after each test series, enabling the calculation of eroded depths and eroded volumes and the estimation of displaced units by using a non-dimensional damage parameter based on the eroded volume.

O presente trabalho descreve a aplicação do modelo numérico COULWAVE ao estudo da propagação de ondas na zona da Praia do Lugar de Baixo, Madeira, com vista a simular as características hidrodinâmicas na zona de estudo permitindo analisar as alturas de ondas, zona de rebentação e reflexão da onda junto à costa. O objetivo final é propor soluções para a renaturalização desta zona e o melhoramento das condições de surf.

The objective of this paper is to describe and compare the use of different high-resolution survey techniques to create and analyse 3D surface models made up of point clouds, using open-source and freeware post-processing tools. Within this framework, several tests were conducted on a three-dimensional scale model of a breakwater, with surveys performed by a smartphone, the Microsoft® Kinect® sensor and a UAV camera. All the tests were conducted for a physical model placed in an empty wave tank. For this comparison, a number of post-processing software were used: the Microsoft Kinect Fusion Application, Visual SFM and MicMac, all freeware software. The clouds of points were compared using the CloudCompare freeware software and the Golden Software Surfer commercial software.In order to obtain a clear comparison between these tools (i.e., to better evaluate accuracy and associated errors), all the point clouds (with RGB colour information) were aligned with data coming from a survey used to coordinate some points in the model (Ground Control Points). All the clouds were compared with a corrected cloud based upon coordinated points painted on the concrete floor of the wave tank.The specific experimental conditions needed for using each of these methodologies were investigated and classified.

Nesta comunicação apresenta-se os novos desenvolvimentos que estão em curso no sistema SWAMS ALERT, que é um sistema previsão, alerta e avaliação de risco de eventos perigosos associados à navegação em áreas portuárias e ao comportamento dos navios amarrados.O sistema usa as características da agitação marítima previstas para determinar os seus efeitos em termos de forças em amarras e defensas, bem como de movimentos de um navio amarrado. Para isso, o sistema utiliza um conjunto de modelos numéricos. O sistema consiste em quatro módulos: I - Características da agitação marítima; II - Navegação em áreas portuárias; III - Avaliação de Risco e IV - Sistema de Alerta. A interface do sistema é através de uma plataforma web totalmente interativa e amigável.Ilustra-se a aplicação deste sistema ao porto da Praia da Vitória.

This paper presents recent new features of the Systematic Observation of Maritime Works (OSOM+) program, under development at LNEC since 1986, for using in an extensive number of maritime structures of mainland Portugal. Those functionalities are illustrated with applications to a real case scenario (the port of Ericeira) and by indicating their added-value on the existing methodology.

It is common for the local sea state in coastal waters to be a complex combination of waves due to local and recent wind (the "sea") and long period waves resulting from earlier weather systems, which have travelled many 100s of km with little attenuation of these very long waves (the "swell"). Sea and swell may have very different directions and periods.

This paper presents the validation of a wave maker with active absorption method implemented in FLUENT® RANS-VOF code for modelling long time series of waves propagating and interacting with coastal structures, more specifically, with Oscillating Water Column devices, to cancel out the reflected wave that reaches the wave maker. Verification of the numerical technique was performed in a 3D wave tank in which a technique of multiple active absorption wave makers was used. Good results were obtained in quasi-3D and fully-3D applications showing that active absorption should be used for modelling accurately the complex interaction between wave and coastal structures, in the present case, with an oscillating water column device integrated in a vertical breakwater.

Due to both its geographic location and maritime importance, Portugal is equipped with a large number of port infrastructures, the majority of which built for goals such as to guarantee the tranquility of the sheltered areas of the harbour basins, to help controlling sedimentation by guiding the currents, to protect water taken from thermoelectric plants, amongst others. In Portugal, the most common of these structures is the rubblemound breakwater. Due to its characteristics, maintenance or repair works are common throughout its lifetime. However, the need for these repair works should be evaluated in advance, in order to avoid significant costs associated to those works or, even worse, the collapse of the structure. It is therefore quite important to evaluate the Present Condition of the structure, as well its Evolution and Risk Conditions. The Present Condition is periodically checked on-site and all relevant data gathered is recorded, by filling in inspection forms, in order to perform further comparisons and analyses with previous inspections of the structure, as to eventually characterize Evolution and Risk conditions. To expedite all this process and prevent likely occurrence of errors in data collection, a monitoring tool, supported through a map-based online geographic information system (WebGIS) was developed, enabling the georeferencing of the structures concerned. This system adapts to the location of the user

The air entrainment effect on wave breaking is of the highest importance for the wave energy dissipation. Wave breaking is a complex phenomenon with several physical processes, making it difficult to quantify the contribution of the air in the energy dissipation process. This study presents a different approach where the wave propagation is exposed to air injected in the bottom of a wave flume. The experiment allows studying in a controlled environment the direct effect of the air bubbles in the wave propagation. The measurements show the free surface elevations and velocity profiles at two sections of the wave flume. The turbulence effect of the air injection on the wave propagation was evaluated. The results show differences for the three types of air injection that were tested. The air injection rate of each orifice is an important factor for the wave dissipation. The wave heights were found to decrease due to the air injection. The Turbulent Kinetic Energy shows an increase along the water column and on the downstream direction of the flume.

Apresenta-se nesta comunicação uma técnica baseada em análise de imagem para a medição e caraterização da concentração de ar produzida no processo de rebentação de onda. Para este efeito, realizaram-se filmagens dos ensaios num canal de ondas no Laboratório Nacional de Engenharia Civil (LNEC), que reproduzem dois tipos de rebentação de onda, progressiva e mergulhante. A validação da técnica de análise de imagem é feita por dois métodos, o primeiro com recurso à injeção de bolhas de ar através de uma bomba de ar e o segundo com a medição pontual da concentração de ar com uma sonda de deteção de bolhas de ar. Os resultados, relativos aos dois tipos de rebentação de onda, mostram as concentrações de ar e a distribuição da pluma de bolhas de ar. As medições realizadas permitem quantificar e caracterizar o ar emulsionado no processo de rebentação de onda.

Um dispositivo de aproveitamento da energia das ondas de tipo coluna de água oscilante (CAO) near-shore (que pode se assimilar a um cilindro vertical oco com a sua parte inferior aberta e a parte superior equipada com uma turbina Wells) implementada em profundidade intermédia pequena é estudado numericamente recorrendo a um modelo RANS-VOF 3D. O modelo numérico integra técnicas de geração e absorção das ondas por batedores múltiplos que permite dispor de um tanque de onda eficiente, eliminando as ondas reflectidas e difractadas. O dispositivo de CAO near-shore é um dispositivo alternativo ao clássico dispositivo integrado em quebra-mar ou na linha de costa e ao dispositivo off-shore (assimilado a um cilindro vertical oco estabilizado por um sistema de ancoragem por cabos) e tem duas vantagens: a resposta do dispositivo é independente da direcção das ondas e pode ser facilmente afundado no fundo do mar já que o dispositivo é desenhado para ser implementado em profundida pequena (~20 m). No entanto, a proximidade do fundo e a interacção complexa onda-estrutura resultante podem interferir em termo hidrodinâmico e energético na resposta do dispositivo CAO near-shore, comparativamente a um dispositivo off-shore. O artigo apresenta os primeiros resultados deste projecto através da análise pormenorizada de um caso de agitação marítima. Também, permite evidenciar e prever respostas diferentes do dispositivo CAO near-shore de um dispositivo clássico off-shore através da analise das series temporais de elevação de superfície livre, do caudal na turbina, da pressão na câmara-de-ar da CAO, da potência pneumática e dos vectores e campos de velocidade e de vorticidade ao redor e dentro do dispositivo.

N/A

N/A

N/A

N/A

N/A

A major objective of TRA LISBON 2022 Conference is to boost research and innovation capacity for the transport sector, throughout a full innovation cycle, from idea to market. Having this in view, the project

The demonstration area will be one of the main focus points of TRA LISBON 2022, presenting multifunctional spaces and being prepared to receive a large number of different types of on-site demonstrations (indoor and outdoor). On-line demonstrations will also be an option, allowing for the widest possible coverage of access for all the participants.The dedicated areas will allow for interactive demonstrations of technological innovations to be carried out by and for industry partners, researchers, and other stakeholders. Demonstrations are an excellent opportunity to introduce conference attendees in an engaging way, as well as to promote new contacts and promising business.

According to the CSA project plan, WP5.2 task objective is to organize technical tours that feature attractive and interactive showcases aiming at engaging participants into novel technologies for all transport modes and enabling stakeholders and their companies to disseminate and even sell their products and applications to all interested parties.

This report is part of HYDRALAB+ Work Package 10, which seeks to strengthen the coherence of experimental hydraulic and hydrodynamic research undertaken by the HYDRALAB+ partner organisations. It outlines the work carried out by Samui Design & Management Ltd, supported by HR Wallingford, in relation to the development of a data repository structure that can be adopted by participants of the HYDRALAB+ project.

Reliable prediction of wave run-up/overtopping and structure damage is a key task in the design and safety assessment of coastal and harbor structures. Run-up/overtopping and damage must be below acceptable limits, both in extreme and in normal operating conditions, to guarantee the stability of the structure and the safety of people and assets on and behind the structure. The mean-sea-level rise caused by climate change and its effects on wave climate may increase the number and intensity of run-up/overtopping events and make the existing coastal/harbor structures more vulnerable to damage.Accurate estimates, through physical modelling, of the statistics of overtopping waves for a set of climate change conditions, are needed. The research project HYDRALAB+ (H2020-INFRAIA-2014-2015) gathers an advanced network of environmental hydraulic institutes in Europe, which provides access to a suite of environmental hydraulic facilities. They play a vital role in the development of climate change adaptation strategies, by allowing the direct testing of adaptation measures and by providing data for numerical model calibration and validation. The use of physical (scale) models allows the simulation of extreme events as they are now, and as they are projected to be under different climate change scenarios.The enclosed dataset refers to the experimental work developed at LNEC within HYDRALAB+ and considers 2D damage and overtopping tests for a rock armor slope, with four different approaches to represent storms. Data of free surface elevation, overtopping and damage is presented.

The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.2 of the HYDRALAB+ project, entitled

The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.3 of the HYDRALAB+ project, entitled

This deliverable is related to task 8.2

Neste relatório inicial são apresentadas a arquitetura e as caraterísticas gerais dos protótipos do sistema de previsão, alerta e gestão de riscos causados pela agitação marítima para os portos de Madalena do Pico, São Roque do Pico e Praia da Vitória. Os três protótipos em desenvolvimento têm por base uma arquitetura semelhante, com características distintas, nomeadamente no que respeita à localização dos dados de base, às malhas computacionais utilizadas e às características físicas das fronteiras, tanto no plano horizontal (interface terra-mar), como no vertical (batimetria dos fundos). Caracteriza-se o layout geral dos portos, bem como a sua morfologia e operabilidade.

N/A

Realização de ensaios em modelo físico reduzido 3D para a avaliação da estabilidade do quebra-mar destacado do Porto Inlgês, Maio, Cabo-Verde

N/A

Adverse sea conditions can cause emergency situations associated to wave overtopping, which endanger the safety of people and goods, with negative impacts for society, the economy and the environment. Therefore, a methodology to assess the overtopping risk in port and coastal areas is essential for a proper planning and management of these areas.The Portuguese National Laboratory for Civil Engineering (LNEC) has been developing the HIDRALERTA system, an integrated decision-support tool for port and coastal management, which focus in preventing and supporting the management of emergency situations and the long-term planning of interventions in the study areas. It enables the user to calculate the risk for various port and coastal activities, starting with the characterization of sea-waves, wind field and tide levels at the study regions.HIDRALERTA was already tested at different places in Portugal: Costa da Caparica beach, in Almada, and port of Praia da Vitória, in the Azores. However, in both cases, the evaluation of wave overtopping / flooding consequences was carried out using a quite simple approach. In fact, such consequences were assessed only at a global and qualitative level, based on information provided by the responsible authorities.This paper aims at testing a quantitative methodology to evaluate overtopping consequences: the Analytic Network Process (ANP). This methodology was proposed to solve complex decision-making problems and its objective is to calculate the priorities among decision elements which will define their final weights on the consequences. The ANP approach can produce interdependencies between criteria and compute the respective weight of each criterion. Such a network model with dependence and feedback improves the priorities derived from judgements and makes prediction more accurate. So, the ANP allows comparison among clusters of elements. Furthermore, in this methodology we take into account the impacts of alternatives on the importance of criteria, by normalizing the comparison matrix. Thus, the given alternatives can influence the ranking of criteria.Application of the ANP methodology to the case study of Praia da Vitória port is presented and a consequences level map is obtained.

Apresenta-se um novo sistema de alerta para navios amarrados em portos que se encontra em desenvolvimento no Laboratório Nacional de Engenharia Civil. O sistema SWAMS_ALERTA é um sistema de previsão e alerta baseado na avaliação do risco associado ao comportamento de navios amarrados em zonas portuárias.Os riscos associados a navios amarrados decorrem de movimentos excessivos, quer no plano horizontal, quer no plano vertical. Estes movimentos podem condicionar as atividades portuárias, nomeadamente cargas e descargas, mas em casos extremos podem levar à ocorrência de situações de emergência, tais como rotura de cabos, rotura de cabeços de amarração ou até colisões com o cais. As consequências deste tipo de situações envolvem sempre grandes prejuízos materiais e por vezes humanos.O sistema SWAMS_ALERTA utiliza as medições e previsões de agitação marítima para a determinação dos seus efeitos em termos de movimentos nos seis graus de liberdade e forças nas amarras e defensas quando o navio se encontra estacionado no cais. Para tal, o sistema recorre a uma série de modelos numéricos, interligados entre si. A comparação destes valores com valores máximos admissíveis pré-estabelecidos permite a avaliação, em tempo real, de situações de emergência e a emissão de alertas dirigidos às entidades portuárias.O sistema é constituído por 4 módulos:I

N/A

N/A

N/A

N/A

N/A