Publicações

In order to contribute to the knowledge about the influence of several factors on the in-service performance of renders, as well as about the applicability of in-situ testing techniques in the evaluation of their performance, an experimental work was carried. In this work, the influence of some factors (type of substrate, number and thickness of mortar layers) on the mechanical and physical performance of two mortars (site-made and industrial) was evaluated, using the following in-situ testing techniques: pendulum rebound hammer test (with two types of rebound hammer), ultrasonic pulse velocity test (with two types of device) and water absorption under low pressure test (with Karsten tubes). It was possible to verify that the above-mentioned factors influence the performance of the mortars. The in-situ testing techniques were, in general, able to identify differences in the behaviour of renders due to these factors. However, for the same technique, different devices sometimes led to distinct results. Nevertheless, the combination of the results of different techniques helped to reduce the uncertainty of the analysis.

Rehabilitation of facades may be carried out with the application of External Thermal Insulation Systems (ETICS). Their main contribution is the increase of the energy efficiency of buildings. In the literature, hygrothermal, impact and fire performance studies have been carried out on several systems with different insulation materials, such as expanded polystyrene, mineral wool and extruded polystyrene foam insulation. Due to the growing concern with the environment, systems are being developed with more sustainable and ecological materials, such as ICB (expanded cork). These type of boards are responsible for a negative impact in global warming potential, significantly improving the environmental benefits of their use. As these systems were recently introduced to the market, applications on site are very recent and their behaviour over time still unknown. In this research, the durability and global performance of more sustainable systems (with ICB) were analysed through an experimental campaign and compared with EPS (expanded polystyrene) systems. The results show that the systems with ICB obtained satisfactory global behaviour comparable with the EPS systems. The ICB sustainable systems analysed stood out in acoustic performance. ...

External Thermal Insulation Composite Systems (ETICS) are constructive solutions widely used to increase the thermal insulation in new and retrofitted buildings. However, these systems can present several anomalies due to their constant exposure to weathering agents and anthropic factors. Water is generally the major cause of degradation. Thus, the application of water-repellent products can minimize the appearance of anomalies and increase the durability of the systems. In this paper, acrylic-based and siloxane-based hydrophobic products were applied to ETICS, with the aim of assessing the compatibility, effectiveness, and durability of these products. The moisture transport properties and mould susceptibility were assessed through laboratory tests on untreated and treated specimens. The durability of the hydrophobic treatments was also evaluated through artificial aging tests (heat-cold and freeze-thaw cycles). Results show that the protection products generally decreased water absorption, slightly decreased the drying rate, and presented adequate water vapor permeability. After aging, the products still had reasonable effectiveness and, with one exception, improved the water vapor diffusion of the systems. Additionally, ETICS underwent an alteration in the finishing coat (possible modification of the porosity) due to the aging cycles. No clear linear correlation was found between the contact angle values and water absorption results, evidencing the influence of other factors related to the composition of the water-repellent products. ....

One of the main functions of renders, together with the overall aesthetic appearance of the building, is the protection of the walls against external aggressive actions, such as water, salts solutions, erosion, and mechanical impacts. However, some anomalies of renders may drastically hinder their protection ability. In fact, cracking, high water permeability, and loss of adherence to the substrate of renders limit their barrier effect and favour the exposure of the substrate to external actions. The incorporation of fibres in mortars is commonly pointed out to reduce their cracking susceptibility, due to the probable enhancement in tensile strength and ductility of the composite.The use of lime in substitution of the part of the cement binder is seen as a method to reduce the modulus of elasticity and therefore enhance the resistance to cracking due to drying shrinkage.Therefore, this study investigates the wall protection-related properties of natural fibre-reinforced renders with cement-lime as a binary binder at 1:1:6 volumetric ratio. With this purpose, wool,coir, and flax fibres are used at 20% by total mortar volume and the water behaviour, cracking susceptibility, and adherence to the substrate of the mortars are assessed. Specifically, the water absorption by capillarity, drying rates, permeability to water under pressure, adherence strength,and shrinkage are evaluated. In order to evaluate the renders

One of the main functions of renders, together with the overall aesthetic appearance of the building, is the protection of the walls against external aggressive actions, such as water, salts solutions, erosion, and mechanical impacts. However, some anomalies of renders may drastically hinder their protection ability. In fact, cracking, high water permeability, and loss of adherence to the substrate of renders limit their barrier effect and favour the exposure of the substrate to external actions. The incorporation of fibres in mortars is commonly pointed out to reduce their cracking susceptibility, due to the probable enhancement in tensile strength and ductility of the composite. The use of lime in substitution of the part of the cement binder is seen as a method to reduce the modulus of elasticity and therefore enhance the resistance to cracking due to drying shrinkage. Therefore, this study investigates the wall protection-related properties of natural fibre-reinforced renders with cement-lime as a binary binder at 1:1:6 volumetric ratio. With this purpose, wool, coir, and flax fibres are used at 20% by total mortar volume and the water behaviour, cracking susceptibility, and adherence to the substrate of the mortars are assessed. Specifically, the water absorption by capillarity, drying rates, permeability to water under pressure, adherence strength, and shrinkage are evaluated. In order to evaluate the renders

Construction and demolition wastes (CDW) are generated at a large scale and have a diversified potential in the construction sector. The replacement of natural aggregates (NA) with CDW recycled aggregates (RA) in construction materials, such as mortars, has several environmental benefits, such as the reduction in the natural resources used in these products and simultaneous prevention of waste landfill. Complementarily, CDW have the potential to capture CO2 since some of their components may carbonate, which also contributes to a decrease in global warming potential. The main objective of this research is to evaluate the influence of the exposure of CDW RA to CO2 produced in cement factories and its effect on mortars. Several mortars were developed with a volumetric ratio of 1:4 (cement: aggregate), with NA (reference mortar), CDW RA and CDW RA exposed to high levels of CO2 (CRA). The two types of waste aggregate were incorporated, replacing NA at 50% and 100% (in volume). The mortars with NA and non-carbonated RA and CRA from CDW were analysed, accounting for their performance in the fresh and hardened states in terms of workability, mechanical behaviour and water absorption by capillarity. It was concluded that mortars with CDW (both CRA and non-carbonated RA) generally present a good performance for non-structural purposes, although they suffer a moderate decrease in mechanical performance when NA is replaced with RA. Additionally, small improvements were found in the performance of the aggregates and mortars with CRA subjected to a CO2 curing for a short period (5 h), while a long carbonation period (5 d) led to a decrease in performance, contrary to the results obtained in the literature that indicate a significant increase in such characteristics. This difference could be because the literature focused on made-in-laboratory CDW aggregates, while, in this research, the wastes came from real demolition activities, and were thus older and more heterogeneous.....

O pavilhão da Casa da Pesca está inserido na Quinta de Recreio dos Marqueses de Pombal, em Oeiras.Edifício de arquitetura simples e feição clássica, serviu para guardar instrumentos da pesca, mas tambémpara o repouso e recreio das elites. Cedido ao Município de Oeiras, este promoveu um plano de conservação e restauro com vista à sua preservação e usufruto pela população que envolveu, entre outras ações,uma caracterização detalhada dos materiais empregues na construção, nomeadamente as argamassas de revestimento. Os autores apresentam a metodologia adotada, os seus resultados e uma estratégia de conservação / reparação dos revestimentos exteriores.

Salt crystallization is one of the main decay processes in historic masonry mortars, and climate change can worsen the salt weathering effects on those materials as result of, e.g., more often rain falls, more intense solar radiation and sea level rise. In this paper, the effectiveness and durability of a substitution

The use of External Thermal Insulation Composite Systems (ETICS) significantly increased in the last decades due to their enhanced thermal properties, low installation cost and ease of application, not only in new constructions but also for thermal retrofitting of building facades. These multilayer rendering systems are constantly exposed to weathering agents and anthropic factors which can lead to physical-mechanical and aesthetical anomalies and thus affect their durability. However, possible synergetic effects among these agents are often neglected by international technical documents on the evaluation of the effectiveness and durability of ETICS. With the aim of filling this gap, moisture transport properties (capillary water absorption, water vapor permeability, water absorption under low pressure, and drying kinetics), thermal conductivity, mould susceptibility and surface properties (color, gloss, and roughness) of twelve commercially available ETICS were assessed and discussed. Possible links between these factors were analyzed and ETICS performance parameters were defined. Results demonstrate that a deeper knowledge of the correlation among ETICS properties can effectively contribute to the evaluation of the efficiency and long-term durability of these systems.

Coir fiber is a by-product waste generated in large scale. Considering that most of these wastes do not have a proper disposal, several applications to coir fibers in engineering have been investigated in order to provide a suitable use, since coir fibers have interesting properties, namely high tensile strength, high elongation at break, low modulus of elasticity, and high abrasion resistance. Currently, coir fiber is widely used in concrete, roofing, boards and panels. Nonetheless, only a few studies are focused on the incorporation of coir fibers in rendering mortars. This work investigates the feasibility to incorporate coir fibers in rendering mortars with two different binders. A cement CEM II/B-L 32.5 N was used at 1:4 volumetric cement to aggregate ratio. Cement and air-lime CL80-S were used at a volumetric ratio of 1:1:6, with coir fibers were produced with 1.5 cm and 3.0 cm long fibers and added at 10% and 20% by total mortar volume. Physical and mechanical properties of the coir fiber-reinforced mortars were discussed. The addition of coir fibers reduced the workability of the mortars, requiring more water that affected the hardened properties of the mortars.The modulus of elasticity and the compressive strength of the mortars with coir fibers decreased with increase in fiber volume fraction and length. Coir fiber

The purpose of the paper is to describe the main functional elements with defects in illegal residentialbuildings. Three research questions are addressed: What are the main functional elements with defectsin buildings and in dwellings? What are the main defects found? In which way these defects affect theuse of buildings?The defects were identified during a survey to the building stock of the Cova da Moura District(Amadora, Portugal), carried out in 2008. This district is made of illegal constructions, occupies anarea of 16.5 ha and has approximately 5,000 inhabitants. During the survey 833 buildings and1884 units were inspected.The main results are: a) only 13% of these building presented defects in the building structure; b)about 60% of the buildings have defects in the roofing systems (e.g., damp and mould, infiltrations);c) more than 84% of the dwellings have defects in the technical installation such as gas or electricalinstallations most of them classified as severe defects.The main conclusion is that most of the defects detected configure serious risk scenarios, particularlyin terms of the minimum habitability conditions and fire safety. However, defects related to structuralstability were not as serious as expected for this kind of construction.

This work is inserted in a wider project aiming at the conservation and durability of historical renders, through compatible techniques and materials; in particular the restitution of cohesion of historical renders is studied. Surface consolidation, directed to restore cohesion and stability, is based on the use of materials with aggregating properties. This operation is reached usually through the use of inorganic or mineral consolidants, which are preferred to organic ones, due to better compatibility and durability. Based on the results of previous studies, two mineral compatible products were selected: a commercial dispersion of nanoparticles of calcium hydroxide in propanol and a calcium-silicate product, consisting on a limewater dispersion of ethyl silicate. Consolidation products were applied on mortar specimens (mortar prisms and mortars applied on bricks) in order to assess their efficacy by determining their microstructural and physical-mechanical properties, before and after consolidation treatment. A low binder ratio mortar was studied with both consolidants.Microstructural (optical and SEM microscopy) and chemical analysis of the consolidation products and of the consolidated samples were performed; physical-mechanical analysis, namely superficial hardness is reported.

External Thermal Insulation Composite Systems (ETICS) are innovative systems; their application improves the buildings

External Thermal Insulation Composite Systems (ETICS) are innovative systems; their application improves the buildings

This work is inserted in a wider project aiming at the conservation and durability of historical renders, through compatibles techniques and materials; in particular the restitution of cohesion of historical renders, turned friable by the loss of binder due to physical or chemical actions, is studied. Surface consolidation, directed to restore cohesion and stability, is based on the use of materials with aggregating properties. This operation is reached usually through the application of organic or mineral consolidants, but inorganic consolidants (such as calcium hydroxide or ethyl silicate) are becoming preferred due to better compatibility and durability.Based on the results of previous studies, two mineral compatible products were selected for the first phase of tests: a commercial suspension of nanoparticles of calcium hydroxide in propanol (Nanorestore); a silicate product, consisting on a limewater dispersion of ethyl silicate.Consolidation products were than applied on different mortars samples previously prepared, in order to assess their efficacy by determining their physical, mechanical and microstructural properties before and after the consolidation treatment. Mechanical and physical analyses were performed, such as compression and flexural strenght and superficial hardness. Microstructural and chemical analyses of the consolidation product and of the consolidated samples are also reported.

Resumo: Os revestimentos pré-doseados com base em cimento (monocamada ou não) são constituídos por uma mistura de pó de cimento, cargas minerais e diversos adjuvantes, seleccionados e doseados em fábrica. Em obra, apenas é necessária a adição de água para se proceder à amassadura. A apreciação técnica destes produtos é feita com base em ensaios de laboratório, a partir dos quais se caracteriza o seu comportamento mecânico e físico. Por outro lado, a avaliação do desempenho dos revestimentos durante a sua vida útil refere-se aos produtos aplicados e sujeitos a determinadas condições climáticas e ambientais, logo deve ser efectuada em obra. O recurso a ensaios in situ permite uma avaliação quantitativa desse desempenho. No entanto, a actual inexistência de normas, de especificações e de ensaios, que enquadrem esse tipo de avaliação, requer um trabalho de base de fixação de condições de ensaio e de interpretação dos respectivos resultados. Neste trabalho foi efectuada uma análise do comportamento mecânico de revestimentos pré-doseados com base em cimento, através de ensaios laboratoriais e de ensaios efectuados sobre os mesmos produtos aplicados em muretes localizados em ambiente exterior, utilizando várias técnicas de ensaio in situ. Os produtos foram aplicados por projecção mecânica, com uma espessura variável entre 15 e 20 mm e foram ensaiados in situ com idades superiores a quatro anos. Os valores obtidos para cada revestimento com os vários ensaios in situ foram comparados entre si e confrontados com os resultados dos ensaios de laboratório realizados à data das aplicações. Desta análise extraíram-se conclusões sobre as técnicas de ensaio in situ, o significado dos valores obtidos e a sua utilidade para a avaliação do desempenho de revestimentos pré-doseados de cimento.

N/A

Abstract In interventions on historic renders and plasters, the first step is to decide upon the strategy: repair or substitution, based on an evaluation of the cultural value of the render or plaster, of the building itself and on a careful diagnosis of the typology of defects, their density and reparability. New renders or repaired renders should fulfil the main functions they are required to, especially protection and aesthetic functions Compatible materials should always be used. Compatibility is needed for durability, not of the render, but of the wall as a whole, and also for preserving the documentary and symbolic value of the building as well as its image. Compatibility is defined in relation to the substrate and the existing mortars. Therefore tests need to be carried out on the old materials and on possible solutions, to compare characteristics and assist in the selection of the best. It is acceptable to begin using non-destructive or slightly destructive in-situ tests, because with them it is possible to collect useful information quickly and without destruction of the historic renders. Simple mechanical and physical tests can be carried out on the old mortars and a few chemical tests can also be performed, with portable equipment. If rigorous and complete tests are needed, some samples can be collected and tested in the laboratory, using methods adapted to non-regular, possibly friable specimens. The characteristics of the mortars to use can be established, based on the results obtained, in order to fulfil both functionality and compatibility. However, sometimes it is not possible to obtain enough data about old materials, especially concerning masonry as a whole, which is more difficult to test than mortars. For this situation, some general requirements have been established, based on previous work carried out on Portuguese historic masonry buildings, which can be used without risk of damaging existing materials. Decisions concerning the materials to use, especially binder materials, should also take into account the climatic and environmental conditions. Appropriate application techniques, workmanship and curing conditions are indispensable in achieving good aesthetic, physical and mechanical results. Therefore it is important to know what conditions are available for the application phase. An effective knowledge of the historic materials and of the possible compatible solutions, of their characteristics and problems, is essential; tests are an important tool but the interpretation of their results in order to take useful decisions is a complex task, requiring a multidisciplinary team efficiently coordinated.

The loss of adhesion of plasters has as a consequence the separation between mortar and support, an anomaly designated as detachment; which may endanger the users

N/A

This book provides insights regarding the involvement of teenagers in the co-creation of public open spaces. It brings together conceptual reflections and an exploratory case study in Lisbon. It is an attempt to point out the intangible benefits of engaging young people in placemaking to academics, practitioners, policymakers, students, and all parties concerned with urban development. This book aims at inspiring progressive placemaking and co-creation processes. It attempts to reframe the debate on how vulnerable members of the community access public spaces, what their needs are, and what their response would be to a more people-centred urban design. It is with respect to these points that the book Territorial capacity and inclusion: Co-creating a public space with teenagers explores and analyses the engagement of teenagers in the production of public spaces. A group who rarely have opportunities to be heard and for their views to be considered. On these particular matters, the teenagers

Personal well-being, health and productivity of building occupants depend to a large extent on available thermal and visual conditions.Thermal and visual requirements have changed across centuries. Last century, as a result of the economic growth that occurred in developed societies, the satisfaction of those requirements gained importance. In a society and period where energy was abundant and cheap, the easiest way to provide desired indoor conditions consisted in the systematic use of artificial conditioning (AC) and electric lighting. As a consequence, resulting energy consumption became significant.Actually, the growing tendency for the use of AC systems, particularly in office buildings, transports and, more recently, in residential buildings and the systematic and the permanent use of electric lighting proceed.Although this fact may derive from a change in user comfort requirements and expectations, they may also reveal design and lifestyle trends conducting to unsustainable options concerning construction, rehabilitation and everyday use of buildings.As a matter of fact, some contradictory aspects can be detect: intolerance in relation to exterior/interior climate variations, the option of non-climate-conscious building solutions and the creation of controlled indoor climates which frequently do not provide the desired well-being conditions (in working, leisure or living places) and unnecessary and excessive energy consumption...

Mortars and sustainabilityMortars are construction materials composed of three main constituents: aggregates,binders, and water. There are other constituents that can be added to improve ormodify the mortars

N/A

The challenge of creating places that promote place attachment, a sense of belonging and community identity peaks in places of super-diversity. Super-diversity commonly generates a fragmented society due to variegated cultural backgrounds, language and weak social bonds and civic activities. An increasingly wide and plural scenario is a challenge for place attachment. In such super-diverse places, largely due to immigration, new socio-spatial patterns and identities arise, posing a particular challenge for public space design. Placemaking, as a bottom-up and people-centred process of improving the liveability of cities through collaboration and community participation, could counter these challenges. It ideally creates a virtuous cycle in which the community transforms and reshapes spaces. Community engagement and a holistic focus on a sense of place are key components of placemaking, which in turn bears a great potential for empowerment. Moreover, placemaking approaches can potentially contribute to co-creation of physical and social spaces that bring locals and immigrants to interact with each other and to connect to the environment. This co-creation and engagement in a super-diverse context can be fostered through digital and mobile technologies, such as social media. This chapter discusses some of the challenges and opportunities posed to placemaking and place design in super-diverse urban contexts. The question that arises is: How can placemaking benefit from super-diversity to create place attachment and mutual benefits for the communities? As an inspiring discussion, the chapter considers some of the challenges posed by the current redesigning process of Martim Moniz Square in Lisbon

The challenge of creating places that promote place attachment, a sense of belonging and community identity peaks in places of super-diversity. Super-diversity commonly generates a fragmented society due to variegated cultural backgrounds, language and weak social bonds and civic activities. An increasingly wide and plural scenario is a challenge for place attachment. In such super-diverse places, largely due to immigration, new socio-spatial patterns and identities arise, posing a particular challenge for public space design. Placemaking, as a bottom-up and people-centred process of improving the liveability of cities through collaboration and community participation, could counter these challenges. It ideally creates a virtuous cycle in which the community transforms and reshapes spaces. Community engagement and a holistic focus on a sense of place are key components of placemaking, which in turn bears a great potential for empowerment. Moreover, placemaking approaches can potentially contribute to co-creation of physical and social spaces that bring locals and immigrants to interact with each other and to connect to the environment. This co-creation and engagement in a super-diverse context can be fostered through digital and mobile technologies, such as social media. This chapter discusses some of the challenges and opportunities posed to placemaking and place design in super-diverse urban contexts. The question that arises is: How can placemaking benefit from super-diversity to create place attachment and mutual benefits for the communities? As an inspiring discussion, the chapter considers some of the challenges posed by the current redesigning process of Martim Moniz Square in Lisbon

The EFFICACY HANDBOOK is a comprehensive guide that addresses critical aspects of energy efficiency and sustainability in building design. It covers a broad spectrum of topics, including understanding energy demands, addressing energy poverty, making informed choices about thermal insulation materials and retrofit solutions, considering the impact of climate change, and preparing for future scenarios. It also provides strategies for effectively engaging target groups.With this publication, the multidisciplinary team of the Efficacy project intends to synthesize and provide the main results of the project, which was completed in September 2023, regarding the Energy eFFiciency buIlding and CirculAr eConomY for thermal insulation solutions. It also includes some insights from the final workshop and technical guidelines. The main topics covered in this work are the following:- Energy poverty (EP) and energy demands- Choice of thermal insulation materials and retrofit solutions- Climate change and future scenarios- Target groups engagementWe hope that this publication will be a relevant contribution to the development of criteria for thermal insulation systems and that the results and guidelines presented here will be useful for all professionals involved in the building energy efficiency and climate change.

This chapter proposes an introductory conceptual framework to better understand some aspects of everyday relations of people and spaces. From the perspective of anthropology of space, it first provides a reflection on issues that are important for understanding these relationships, to then, in a second step, address the relevance of walking as a method to trigger a sensitive path. This chapter aims to raise the interest for urban planning that is more attentive to the multidimensionality of socio-territorial relations. To explore the sensitiveness of urban space it is important to consider (a) the perspective of users in terms of symbolic dimensions, socio-spatial and cultural practices, and sense of happiness and well-being; (b) the articulation between behavioural dimensions, sociocultural dynamics and the environment; (c) the approximation of concepts and categories to understand space from the perspective of different disciplines. Keywords - Attentiveness, socio-territorial relations, walking, urban planning

Resumo: Ambiente construído é um conceito amplo e difuso; talvez essa seja uma de suas virtudes capitais. A pesquisa nessa área de fronteiras tão impre­cisas permite abordagens de temas, escalas e métodos diversificados. Neste livro, a reunião de ensaios feitos por pesquisadores de diferentes países sobre variados tópicos, com apropriações metodológicas tão diversas, reafirma o caráter múltiplo desse campo. Nesta ótica, destaca-se o papel de uma observação sistemática e minuciosa das complexas interações que resultam da relação entre os múltiplos e diversificados usos dos espaços públicos urbanos, as apropriações, contra apropriações, representações do espaço e respectivas tem­poralidades envolvidas, considerando a sua ligação com propostas arquitetônico-urbanísticas de desenho e intervenção. Este livro é o registro de um momento do campo, mas também representa a possibilidade de novas incursões que podem alargar suas fronteiras. Abstract: Built environment is a broad and diffuse concept; perhaps this is one of its capital virtues. Research in this area of such inaccurate bound­aries allows approaches from diverse themes, scales and methods. In this book, the gathering of essays by researchers from different countries on various topics, with such diverse methodological ap­propriations, reaffirms the multiple character of this field. In this perspective, it highlights the role of a systematic and thorough observation of the complex interactions that result from the relationship between the multiple and diverse uses of urban public spaces, appropriations, against appropriations, representations of space and respective temporalities involved, considering their connection with architectural-urbanistic proposals of design and intervention. This book registers a specific moment in the field but it also rep­resents the possibility of further inroads that may broaden its borders.

As praças de uma cidade são espaços públicos consagrados historicamente à vida coletiva. Nesta publicação estão reunidos artigos que têm algumas importantes praças da área central da cidade do Rio de Janeiro como tema de estudo. As praças são analisadas a partir de suas dimensões material e simbólica, como produtos de ações que perpassam vários projetos para o espaço público. São destacadas as praças XV de novembro; Tiradentes; Mauá e Onze -esta última, já não mais existente fisicamente. As praças, portanto, se afirmam como estruturas espaciais de destaque no ambiente construído e como lugar para a representação da memória em tempos de constantes transformações. - The city's squares are public spaces historically dedicated to collective life. This publication brings together articles that have some important squares in the central area of the city of Rio de Janeiro as their subject of study. The squares are analyzed from their material and symbolic dimensions, as products of actions that permeate various projects for public space. There are highlighted the squares XV de Novembro; Tiradentes, Mauá and Onze - the latter, no longer physically existing. The squares, therefore, assert themselves as prominent spatial structures in the built environment and as a place for the representation of memory in times of constant transformation

A partir de uma incursão teórica sobre a noção de memória social, investiga-se como esta tem sido um recurso para incrementar a conexão das pessoas com os rios urbanos. A reflexão realiza-se no âmbito do estudo de caso presentemente em curso em Lisboa e que se dedica à investigação do contributo da memória no resgate da paisagem fluvial para o imaginário social e urbano contemporâneo. Para o efeito, aqui parte-se da relação da memória com os espaços materiais, naturais e mentais das sociedades humanas ligados à recordação de experiências passadas. Neste sentido, explora-se o seu contributo para recuperar os cursos de água para o imaginário social e urbano contemporâneo. Analisa-se como a memória tem sido discutida relativamente aos rios urbanos e que, em decorrência da iminência de riscos e de situações de catástrofes associadas ao sistema fluvial urbano, se tem destacado como recurso para a criação de dinâmicas de adaptação e resiliência. Seguidamente, analisam-se iniciativas que, fazendo recurso à memória ligada aos rios, contribuem para sensibilizar e influenciar a conexão das pessoas com os cursos de água em meio urbano, ainda que isto possa ser sugestivamente. Palavras-chave - Memória social, paisagem fluvial, imaginário social e urbano

O livro RIOS URBANOS NA IBERO-AMÉRICA - CASOS, CONTEXTOS E EXPERIÊNCIAS apresenta o primeiro conjunto de reflexões produzidos no âmbito da rede temática Ibero-americana RUN

Coimbra apresenta um elevado valor arquitetónico demonstrado pelos 36 imóveis, conjuntos ou sítios (22 monumentos nacionais e 14 imóveis de interesse público) actualmente classificados (DGPC, 2015) sendo a maioria deles localizados no Centro Histórico de Coimbra (CHC) e zona alta da cidade.No âmbito do projecto POCI/HEC/60371/2004

A relação entre património material (arquitetónico) e imaterial (como saber técnico-tradicional)orientou um estudo sobre técnicas e materiais tradicionais de revestimentos históricos exteriorescom base em cal, realizado para o Projeto «Conservação e durabilidade de revestimentoshistóricos: compatibilidade, técnicas e materiais

Indoor walls and ceilings are often coated with plasters. Due to the large surface in contact with indoor air, the plasters can passively contribute to moisture regulation and pollutant removal. The work presented intends to better understand this contribution, while enhancing, when possible, the plasters formulations for the purpose. The first step was to analyze the hygroscopic response of traditional and modern binder-based plasters. To do so, a first study was run to quantify the relative humidity fluctuations indoor. Then, the methods fitting the most the real indoor microclimates were selected for testing. The campaign was run along with bibliographic research, to match laboratory results with those ones present in literature. The compatibility with the preexisting materials and products and the eco-efficiency of the plasters are two parameters that were kept in mind during the work. According to that, clay and gypsum based plastering mortars were selected as the most promising materials. Both, in fact, are present in traditional architecture, besides being suitable solutions for new construction, and have low embodied energy. However, while the clay-based plasters showed a high hygroscopic behavior, the gypsum-based ones showed a lower one. For this reason, the latter was modified through the addition of biomass and the clay-based plasters were kept as a benchmark along the study. The plant selected for the scope is Acacia dealbata, an invasive species that plays a role in the spread of wood fires in Portugal. The biowaste addition was aimed at enhancing the moisture buffering of gypsum-based plasters without jeopardizing other properties or their carbon footprint. Good results were obtained, increasing the moisture buffering ability of the gypsum plaster up to double, even if still lower than the clay-based ones. The ozone reactivity and primary and secondary emission rates (VOCs) of the innovative gypsum-based plaster and the clay-based ones were also analyzed. The ozone removal ability of the gypsum-based plaster was improved by the biomass addition, the primary emissions increased a little, but the secondary ones were very low. Clay-based plasters overall confirmed their low emissions and ozone removal activity.

Exposure to weathering conditions requires selecting and applying solutions with appropriate durability to preserve façades without the need for frequent extensive rehabilitation actions. The consequent heat gain from solar radiation exposure accelerates the degradation of the most exposed façade layer, reducing their service life. An attractive solution to mitigate this overheating is the incorporation of functional nanomaterials in the façades finishing coatings, which reflect a part of the solar radiation in the near-infrared region. This solution may have an even higher influence on dark-coloured coatings, whose use has been increasing by architects and final consumers. To design more energy-efficient buildings, applying thermal insulation systems, such as External Thermal Insulation Composite Systems (ETICS), is necessary. These systems experience significant surface temperature fluctuations (amplified by the dark colour application), causing dimensional variations and naturally leading to cracking.Therefore, this Doctoral Thesis proposes a strategy combining these two façade solutions: dark-coloured finishing coatings applied on ETICS, aiming to improve solar reflectance and reduce the surface temperature. The study focused on developing new dark-coloured formulations with reflective nanomaterials, without excessively changing the visual aesthetics. A systematic study of their intrinsic properties was performed to understand and predict the nanomaterials' behaviour and ability to reflect or absorb. Subsequently, a commercial TiO2 Rutile and a newly developed nanocomposite, combining two nanomaterials, were included in a dark-coloured commercial finishing coating for ETICS and the surface properties were evaluated. The thermo-optical properties revealed an overall total reflectance increase for the two samples (15% and 20%) compared to only 12% of the non-modified finishing coating, providing a similar visual aesthetic. The reflectance improvement observed with the incorporation of nanomaterials certainly impacted the surface temperature, as the modified finishing coatings showed better performance and durability, as evidenced in the accelerated ageing test as thermal oscillations responsible for fractures are reduced.From these results, this strategy could emerge as a promising solution for low-cost dark reflective coatings that can be easily applied on building façades

The importance of the selection of the type of aggregates and their effects on the modification of mortar properties is widely recognized. However, despite recent scientific advances on the effect of aggregates on the properties of mortars and concretes, few studies show how the characteristics of aggregates affect the microstructure and consequently, the final quality of mortars. Moreover, in general, existing studies show that there is an approach mostly related to the use of Portland cement, which several researchers have already shown that have adverse effects, when it is used in rehabilitation works of ancient buildings.In the context of rehabilitation, this factor is particularly relevant, since the main objective is to obtain mortarswith specific characteristics and performances compatible with those that exist in old masonry. The aggregate, as an integral part of mortars, and in some cases defined as their "skeleton", has a direct influence on themicrostructure of mortars, which, in turn, influences the physical, chemical and mechanical properties, as well as the finishing and the final appearance of the renders, especially in the case of lime mortars.Therefore, the present study intends to contribute to a better knowledge of the influence of mineralogical andphysical characteristics (grain size distribution and shape) of the natural aggregates on the mortars

No âmbito da revisão do regime de arrendamento urbano (NRAU), foi desenvolvido no Laboratório Nacional de Engenharia Civil (LNEC) o Método de Avaliação do Estado de Conservação de imóveis (MAEC). Este método permite determinar, de forma expedita, o estado de conservação de edifícios para efeitos de atualização de rendas, mediante a realização de inspeções visuais ao local, efetuadas por técnicos qualificados.O MAEC está em vigor desde novembro de 2006, tendo sido realizadas mais de 30 000 vistorias durante os primeiros quatro anos de implementação. Em junho de 2010, cerca de 2400 técnicos avaliadores estavam inscritos para realizar vistorias com o MAEC.Considerou se assim oportuno realizar um estudo que analisa a experiência obtida com a aplicação do MAEC. Para o efeito, foram analisados os resultados das vistorias realizadas com o MAEC entre janeiro de 2007 e maio de 2010 e a opinião que os principais intervenientes têm sobre o MAEC (i.e., técnicos avaliadores e técnicos das Comissões Arbitrais Municipais). Como complemento, foi realizado um estudo comparativo do MAEC com 16 outros métodos que avaliam o estado de conservação de imóveis (7 portugueses e 9 estrangeiros).Com base nos resultados destas análises, foram avançadas propostas de aperfeiçoamento do MAEC de dois tipos: (i) propostas para simplificar a aplicação da atual metodologia de avaliação e aumentar o nível de informação recolhida e de rigor dos resultados; e (ii) propostas para que a metodologia de avaliação do MAEC permita obter resultados complementares para além daqueles para os quais foi originalmente concebido mas que a experiência de aplicação tem vindo a provar necessários.Como conclusão geral, verifica se que o MAEC cumpre os objetivos principais para os quais foi concebido. Porém, é possível introduzir alguns aperfeiçoamentos que contribuirão quer para a simplificação quer para o aumento do rigor da aplicação do método.

As telhas cerâmicas são muito utilizadas há séculos no revestimento decoberturas inclinadas em Portugal e em muitos outros países. Alguns casos dedegradação acelerada têm vindo a afectar a durabilidade das telhas.Para avaliar o desempenho de telhas cerâmicas em ambiente marítimo foidesenvolvido um estudo experimental baseado em ensaios de envelhecimentoartificial acelerado.Este estudo compreende a caracterização de diversos tipos de telhascerâmicas, o desenvolvimento e realização de ensaios de envelhecimentoacelerado realizados em câmara de nevoeiro salino, a avaliação dadegradação provocada pelos ensaios acelerados e a comparação com adegradação sofrida por telhas em exposição natural.O estudo pretende reproduzir em laboratório os mecanismos de degradaçãoobservados em condições reais e identificar as características mais afectadas,procurando relações significativas entre grandezas relevantes medidas nosmateriais antes e depois da acção dos agentes externos.Pretende-se também, com base na análise comparativa dos resultados dosensaios de envelhecimento sobre diferentes tipos de telhas, identificarparâmetros de composição e de fabrico que contribuem para a degradação efornecer assim à indústria dados relevantes para melhorar a durabilidade dastelhas.

O presente trabalho reporta-se ao tema geral da conservação e restauro de revestimentosexteriores de edifícios antigos, destacando-se como tema específico as questões dodesenvolvimento de uma metodologia de estudo e reparação.Com este estudo foi possível um maior entendimento do comportamento dos revestimentosexteriores de edifícios antigos com base em cal, bem como estabelecer um maior rigor naaplicação de metodologias de conservação e restauro, tendo como objectivo principal a definiçãode uma metodologia de restauro conservativa para a salvaguarda das técnicas, da funcionalidadee do aspecto estético original da fachada exterior de edifícios antigos.Os principais contributos deste estudo foram: (i) estabelecer métodos de análises in situ dorevestimento, para conhecimento da sua técnica, da sua história e do seu estado de conservação;(ii) estabelecer métodos de análise das anomalias do revestimento, onde é possível quantificar ograu de deterioração; (iii) escolher a técnica e o produto consolidante adequado para o tratamentodas anomalias; (iv) especificar as distintas técnicas de restauro e definir os diversos produtosconsolidantes existentes para os revestimentos; (v) aplicar materiais tão compatíveis quantopossível com o revestimento, predominantemente compostos por ligantes minerais, dando-sepreferência aos materiais tradicionais, de modo a verificar a sua eficiência através de ensaioslaboratoriais (vi) estabelecer critérios de aplicação para cada produto ensaiado em função daanomalia observada nos revestimentos; (vi) definir uma estratégia de intervenção geral para cadatipo de revestimento e de anomalia.Enfim, o estudo permitiu estabelecer uma metodologia geral de restauro de revestimentos,desenvolvendo todo um conjunto de técnicas de ensaio, critérios de selecção de produtos e deavaliação de resultados, no sentido da melhor preservação do Património Histórico e do melhorcontrolo do processo de restauro.

A termografia é um método de análise que permite obter uma imagem da distribuiçãoaproximada da temperatura de um objecto, sem contacto físico com este.No domínio dos edifícios as utilizações mais habituais da análise termográfica visama avaliação da qualidade térmica da envolvente e a detecção de pontos de exfiltração ou deinfiltração de ar através dessa envolvente.A presença de humidade, sob a forma de vapor ou de água líquida, é a causa dediversas anomalias e degradações ocorridas nos elementos de construção.A detecção da humidade nos elementos de construção é realizada por métodos querdestrutivos quer não

Após cerca de vinte anos de esforços e de tentativas goradas foram publicadas em 2002 asnormas europeias de ensaio e de classificação de reacção ao fogo dos produtos deconstrução. Neste texto, após uma breve apontamento sobre os antecedentes da novaclassificação, apresentam-se os cinco métodos de ensaio adoptados e os critérios gerais dosistema europeu dessa classificação.Abordam-se, ainda, os aspectos práticos relacionados com a implementação deste sistema,dando-se especial ênfase à possibilidade e limitações da

No presente trabalho apresenta-se um estudo de caracterização térmica, por via analítica , de paredes de alvenaria de utilização corrente em Portugal.Com base no apuramento das características de alguns dos elementos de produção nacional para execução de paredes de alvenaria, definem-se os tipos de paredes que os integram,estabelecem-se para essas paredes uma classificação e uma numeração de referência,e calculam-se, compilam-se e analisam-se em termos comparativos as respectivos característicastérmicas.Em anexos, incluem-se: um exemplo de cálculo das características duma parede(ANEXO I); quadros dessas características para cada tipo de parede (ANEXO II}; e quadrosde síntese das referidas características (ANEXO III).

No presente trabalho apresenta-se um estudo de caracterização térmica, por via an~lítica, dos pavimentos prefabricados aligeirados de produção nacional.Com base no apuramento das características dos pavimentos comercializados com homologação válida em 1980, data do início deste estudo, seleccionaram-se gamas de pavimentosrepresentativas daquela produção, estabeleceu-se uma classificação e uma numeraçãode referência desses pavimentos, e calcularam-se, compilaram-se e analisaram-se em termoscomparativos as respectivas características térm icas.Em anexos, incluem-se: a relação das empresas produtoras dos pavimentos consider~dos no apuramento (Anexo I); um exemplo de cálculo das características de pavimentos(Anexo II); quadros dessas características para cada tipo de pavimento (Anexo III); quadros-síntese das referidas características (Anexo IV) e quadro de registo dos respectivos valoresextremos (Anexo V).

Na presente publicação que se destina a apoiar a realização de estudos no âmbito dodesempenho térmico dos edifícios e a aplicação do Regulamento das Características deComportamento Térmico dos Edifícios (RCCTE), apresentam-se, sob forma tabular, valoresconvencionais de cálculo, por um lado, de condutibilidades térmicas de materiais e deresistências térmicas superficiais, de espaços de ar não-ventilados e de alguns elementosopacos de construção (Anexo I) e, por outro lado, dos coeficientes de transmissão térmicade soluções correntes das envolventes opaca (Anexo II) e envidraçada (Anexo III) dosedifícios.Os vinte e dois quadros do Anexo II correspondentes aos elementos opacos da envolvente

A presente publicação destina-se a apoiar a realização de estudos no âmbito quer daaplicação do Sistema de Certificação Energética (SCE) de edifícios quer das intervençõesde reabilitação térmica dos edifícios existentes, eventualmente visando a verificação documprimento do Regulamento das Características de Comportamento Térmico dos Edifícios(RCCTE).Neste trabalho apresentam-se fichas sumárias descritivas e identificadoras das soluçõescaracterizadas e dos respectivos elementos constituintes, bem como os valoresconvencionais de cálculo das resistências térmicas e dos coeficientes de transmissãotérmica de soluções correntes da envolvente opaca dos edifícios construídos, em geral,antes dos anos 50 do século passado. Apresentam-se ainda alguns elementos decaracterização de soluções adoptadas nas Regiões Autónomas dos Açores e da Madeira.Deste modo a presente publicação visa complementar a Informação Técnica Edifícios (ITE)do LNEC denominada Coeficientes de transmissão térmica de elementos da envolventedos edifícios. Versão actualizada 2006 (ITE 50).Os valores convencionais apresentados (Anexo I) foram calculados a partir da definição desoluções típicas adoptadas na construção de edifícios em Portugal e nas RegiõesAutónomas, tendo como base valores convencionais das características relevantes(condutibilidades térmicas dos materiais, resistências térmicas superficiais e de espaços dear) constantes na ITE 50, e a informação prestada por técnicos dos Laboratórios Regionaisde Engenharia Civil (LREC) dos Açores e da Madeira.Em complemento aos parâmetros de caracterização térmica referidos, para cada uma dassoluções apresentadas indicam-se, ainda, valores convencionais das respectivas massassuperficiais, com o objectivo de apoiar a determinação da massa superficial útil (Msi)necessária à quantificação

N/A

N/A

N/A

N/A

N/A

Values are at the core of any heritage project. While heritage value-thinking usually focuses on site values, it is crucial to pay attention to priorities, assumptions and values of the relevant stakeholders, and make sure they are aligned. Shared values represent a solid foundation for any project and also become the lighthouse that guides decision-making and actions at every stage. You should work collaboratively with stakeholders in order to: detect implicit assumptions detect collective needs collect future visions mapping levels and nature of commitments define the values of the project together with the relevant stakeholders.

N/A

N/A

N/A

Local memory can be an important source of information about the historic site from the perspective of UBH valorisation. Local memory can include oral histories, photographs, and other documents that provide insight into the site