Artigos de Revista
Info
Discontinuum analysis of the fracture mechanism in masonry prisms and wallettes via discrete element method
This study proposes an alternative approach to modeling the failure mechanisms of brickwork assemblages under combined shear
Ano: 2020
Autor(es): Pulatsu, B.; Erdogmus, E.; Lourenço, P.; Lemos, J. V.
Revista: Meccanica
Editor: Springer
Keywords: DEM , Discontinuum analysis , Masonry , Softening , Contact mechanics
Info
Investigation of the Structural Dynamic Behavior of the Frontinus Gate
The Western Anatolia Region of Turkey is an important region of high seismic activity.The active dynamics of the region are shaped by a compression and expansion mechanism. This activemechanism is still ongoing and causes strong seismic activity in the region. The Frontinus Gate is amonument in the Roman city of Hierapolis of Phrygia located in southwestern Anatolia. The aim ofthis study is to investigate the seismic behavior of this stone masonry structure using discrete elementmodeling. For this purpose, nonlinear dynamic analyses were performed to simulate the structuralresponse of the gate under seismic excitation. Deformation, damage, and failure patterns induced inthe masonry gate for di erent levels of seismic action are evaluated and discussed. An earthquakewith a return period of 475 years is expected to cause some damage, but no collapse, while for areturn period of 2475 years, the models indicate collapse of the monument.
Ano: 2020
Número Páginas:
5821.
Autor(es): Saygili, O.; Lemos, J. V.
Revista: Applied Sciences
Editor: MDPI
Volume:
10.
Keywords: stone masonry; discrete element modeling; nonlinear dynamic analysis
Info
Nonlinear dynamic response of stone masonry minarets under harmonic excitation
In this paper three historical masonry minarets in Istanbul, Turkey, are assessed for thedependency between the input harmonic motion and structural response parameters. Theirheights are 40, 73 and 74 m, while the slenderness is 12, 6 and 12, respectively. The discreteelement method is used in dynamic nonlinear analyses. Models were calibrated withmeasured natural frequencies. A series of sine-wave excitations is created for different frequency-amplitude pairs varying between 0.4 and 10 Hz, and between 0.1 and 1 m/s. Fromthe results of dynamic simulations, a general trend was observed for masonry minarets.Especially, slenderness and wall thickness play an important role on their dynamic responseand damage pattern. Dynamic behavior of these minarets cannot reliably be estimated bystatic non-linear analysis. Two engineering demand parameters (EDPs) are defined to characterizethe displacement of the minaret top and the inter-ring shear displacements alongthe minaret body. Damage performance criteria for minarets are proposed based on fourdamage states and tentative limit values are given. We were able to identify the occurrenceof those limit states as a function of frequency and amplitude of sinusoidal input motion.
Ano: 2020
Número Páginas:
4813-4838pp.
Autor(es): Cakti, E.; Saygili, O.; Lemos, J. V.; Oliveira, C.S.
Revista: Bulletin of Earthquake Engineering
Editor: Springer
Volume:
18, 10.
Keywords: Masonry · Discrete elements · Dynamic response · Collapse analysis
Info
Numerical modeling of the tension stiffening in reinforced concrete members via discontinuum models
This study presents a numerical investigation on the fracture mechanism of tension stiffening phenomenon in reinforced concrete members. A novel approach using the discrete element method (DEM) is proposed, where three-dimensional randomly generated distinct polyhedral blocks are used, representing concrete and one-dimensional truss elements are utilized, representing steel reinforcements. Thus, an explicit representation of reinforced concrete members is achieved, and the mechanical behavior of the system is solved by integrating the equations of motion for each block using the central difference algorithm. The inter-block interactions are taken into consideration at each contact point with springs and cohesive frictionalelements. Once the applied modeling strategy is validated, based on previously published experimental findings, a sensitivity analysis is performed for bond stiffness, cohesion strength, and the number of truss elements. Hence, valuable inferences are made regarding discontinuum analysis of reinforced concrete members, including concrete
Ano: 2020
Autor(es): Pulatsu, B.; Erdogmus, E.; Lourenço, P.; Lemos, J. V.
Revista: Computational Particle Mechanics
Editor: Springer
Keywords: DEM · Discontinuum analysis · Tension stiffening · Contact mechanics
Info
Seismic and Structural Health Monitoring of Cabril dam. Software development for informed management
Nowadays, the management and safety control of large dams is generally based on automatic monitoring, including the socalledseismic and structural health monitoring systems (SSHM), using the latest technology for automatic data measurement,acquisition and transmission. These systems should include software for automatic management and analysis of continuousmonitoring data and software for numerical simulation of the dam dynamic behavior using 3D finite element models. Thissoftware should be designed to provide useful and reliable information to meet the needs and expectations of stakeholders,and to support the studies of researchers and engineers responsible for structural health monitoring. This paper is focusedon the experience gathered from the SSHM system of Cabril dam, a 132 m high-arch dam, in Portugal, that has been undercontinuous dynamic monitoring since 2008. The importance of the software specifically developed for automatic modalidentification, automatic detection of seismic vibrations (distinct from vibrations due to the operation of discharge gates andpower groups), and automatic comparison between experimental data and computed results from a reference finite elementmodel of the dam-reservoir-foundation system, is highlighted. This software includes: (1) the generation of graphics withthe evolution of the identified natural frequencies over time and the comparison with calculated frequencies using differenthypothesis for concrete damage evolution; and (2) a service to automatically send emails summarizing key dynamic monitoringresults to stakeholders to provide the necessary support for informed management and engineering decision making.The main results from SSHM of Cabril dam are presented, namely regarding the evolution of modal parameter over time,considering the influence of water level variations, and the measured response during an earthquake event.
Ano: 2020
Número Páginas:
913-925pp..
Autor(es): Oliveira, S.; Alegre, A.
Revista: Special Issue of the Journal of Civil Structural Health Monitoring: SHM for informed Management of Civil Structures and Infrastructures
Editor: Springer
Volume:
Vol.10, N.5.
Keywords: Concrete dams · Cabril dam · Seismic and structural health monitoring system · Modal identification · Ambient vibrations · Seismic response
Info
Simulation of the in-plane structural behavior of unreinforced masonry walls and buildings using DEM
In this study, a novel computational modeling strategy is proposed to estimate the lateral load capacity andbehavior of unreinforced masonry (URM) structures. All commonly noted failure mechanisms are captured viathe proposed modeling strategy using the discrete element method (DEM) in three-dimensions (3D). Masonrywalls are represented as a system of elastic discrete blocks, where the nodal velocities are evaluated by integrating the equations of motion using the central difference method. Then, the mechanical interactions among adjacent blocks are examined utilizing the relative contact displacements and employed in the contact stress calculation. Through this research, a new stress-displacement contact constitutive model is considered and implemented in the commercial software 3DEC, which includes softening stress-displacement behavior for tension, shear, and compression along with the fracture energy concept. The results of the discontinuum models are validated on small- and large-scale experimental studies available in the literature with good agreement. Furthermore, important inferences are made regarding the effect of block size, the number of contact points, and contact stiffness values for robust and accurate simulations of masonry walls.
Ano: 2020
Número Páginas:
2274
Autor(es): Pulatsu, B.; Erdogmus, E.; Lourenço, P.; Lemos, J. V.
Revista: Structures
Editor: Elsevier
Volume:
27.
Keywords: Computational modeling, Contact mechanics, Discrete element method, Unreinforced masonry
Info
sistemas de monitorização dinâmica de barragens de betão para apoio à avaliação da segurança estrutural
De acordo com a legislação portuguesa e tendo em consideração o risco sísmico da zona de construção das barragens é obrigatório a implementação de um Sistema de Observação Sísmica (SOS), incorporando instrumentação para caracterizar a ação sísmica induzida nas obras e a respetiva resposta estrutural. Em complemento, têm sido instalados Sistema de Monitoramento Dinâmico Contínuo (SMDC). O SOS permite não apenas a caracterização da ação sísmica, mas também a sua propagação ao longo do maciço rochoso, bem como a resposta estrutural da barragem. O SMDC visa identificar as características dinâmicas da barragem e sua evolução ao longo do tempo, considerando a variação das condições ambientais e operacionais, bem como a possível evolução das propriedades mecânicas dos materiais. Os processamentos são efetuados automaticamente incluindo a caracterização do nível de aceleração e a identificação dos parâmetros modais da barragem. Os valores obtidos pelo processamento automático são armazenados em base de dados, sendo enviados alertas quando são atingidos os patamares de alarme previamente definidos.Os resultados provenientes destes sistemas são comparados com os resultados de modelos numéricos sofisticados, calibrados com o recurso a ensaios experimentais de caraterização dinâmica realizados na obra durante a fase de primeiro enchimento.A combinação da monitorização dinâmica com os modelos numéricos é uma ferramenta fundamental no controlo de segurança estrutural e gestão de risco das barragens.
Ano: 2020
Autor(es): Gomes, J. P.; Lemos, J. V.; Pereira, S.; Magalhães, F.; Monteiro, G.; Pinho, P.
Revista: Construção Magazine - revista técnica
Editor: Plubindústria
Volume:
95.
Keywords: Sistema de Monitoramento Dinâmico Contínuo; Sistema de Observação Sismica; Comportamento dinâmico; Barragens de betão
Info
Stochastic strength prediction of masonry structures: a methodological approach or a way forward?
Today, there are several computational models to predict the mechanical behaviour of masonry structures subjected to external loading. Such models require the input of material parameters to describe the mechanical behaviour and strength of masonry constructions. Although such masonry materialparameters are characterised by stochastic
Ano: 2020
Número Páginas:
122
Autor(es): Sarhosis, V.; Lemos, J. V.
Revista: RILEM Technical Letters
Editor: RILEM
Volume:
4.
Keywords: Masonry; Material variability; Numerical modelling; Discrete element method
Info
Tensile Fracture Mechanism of Masonry Wallettes Parallel to Bed Joints: A Stochastic Discontinuum Analysis
Nonhomogeneous material characteristics of masonry lead to complex fracture mechanisms,which require substantial analysis regarding the influence of masonry constituents. In this context, thisstudy presents a discontinuum modeling strategy, based on the discrete element method, developed toinvestigate the tensile fracture mechanism of masonry wallettes parallel to the bed joints consideringthe inherent variation in the material properties. The applied numerical approach utilizes polyhedralblocks to represent masonry and integrate the equations of motion explicitly to compute nodalvelocities for each block in the system. The mechanical interaction between the adjacent blocks iscomputed at the active contact points, where the contact stresses are calculated and updated basedon the implemented contact constitutive models. In this research, di erent fracture mechanisms ofmasonry wallettes under tension are explored developing at the unit
Ano: 2020
Número Páginas:
78-93pp.
Autor(es): Pulatsu, B.; Erdogmus, E.; Lourenço, P.; Lemos, J. V.
Revista: Modelling
Editor: MDPI
Volume:
1.
Keywords: material uncertainty; masonry; DEM; discontinuum analysis
Info
The role of modal parameters uncertainty estimation in automated modal identification, modal tracking and data normalization
During the last decade, many vibration-based structural health monitoring systems have been successfully implementedin different structures such as bridges, towers, stadia and wind turbines, with the aim of studying thestructure dynamics and its evolution over time, eventually detecting the occurrence of novel structural behaviourthat may indicate the presence of damage.Such vibration-based monitoring systems generally rely on the identification of modal properties, which arethen used as monitoring features. Therefore, from operational modal analysis to the tracking of those featuresand finally to data normalization, many processing steps occur that depend on the accuracy of the identifiedmodal properties. Thus, the estimation of the uncertainties associated with the identified modal properties increasesthe robustness of this process.In this context, data obtained from the continuous dynamic monitoring of a concrete arch dam has been usedto evaluate the gains of quantifying the uncertainties of modal properties, evaluating in particular the effect oftaking these uncertainties into consideration when performing automated operational modal analysis, modaltracking and data normalization. Nevertheless, it is observed that the most significant gains of consideringestimates uncertainties occur when these quantities are used for removing outliers during modal tracking.
Ano: 2020
Autor(es): Pereira, S.; Reynders, E.; Magalhães, F.; Cunha, A.; Gomes, J. P.
Revista: Engineering Structures
Editor: Elsevier
Volume:
224 (2020) 111208.
Keywords: Modal tracking; Uncertainties in modal properties; Operational modal analysis; Dam monitoring
|
Comunicações
Info
Modelação pormenorizada da fractura em rocha utilizando sistemas discretos de partículas
O comportamento resultante da micro-fendilhação generalizada e/ou da presença de macro-fendas é dificilmente caracterizado a partir de uma formulação contínua. Por este motivo, na modelação da fractura em geo-materiais têm sido propostos modelos detalhados de partículas, inicialmente desenvolvidos para estudo do comportamento micro-mecânico de meios granulares, que têm em consideração a interacção física entre as partículas e a influência da estrutura granular do material. Neste trabalho, é apresentado um modelo de partículas rígidas esféricas que tem sido desenvolvido tendo em vista o estudo da fractura no betão e em rocha. O modelo é validado em ensaios triaxiais, e em ensaios de compressão diametral, em rocha, sendo estudada a influência do modelo constitutivo do contacto.
Ano: 2010
Autor(es): Azevedo, N.; Lemos, J. V.
Info
Monitoring the structural integrity of large concrete dams: the case of Cabril dam, Portugal
The safety control of large dams under static and dynamic loads, involving observation data and numerical modeling, is now one of the challenges of structural engineering. The complexity of the dam-reservoir-foundation geometry, the presence of different types of discontinuities, the water-structure interaction, the influence of thermal and water level variations, the development of deterioration processes over time and the occurrence of exceptional events such as major floods or earthquakes, makes the structural safety control of large dams an activity that requires a continuous updating, both in terms of the equipment for measuring, transmission, and storage of the observation data, and in terms of computer applications to support the automation process of collecting, processing, analysis and management of all information required to the safety control. The recent LNEC and EDP experience on the revision of the monitoring system of Cabril dam, the highest portuguese arch dam, is presented as a case study in this paper. After a brief presentation of the main dam characteristics
Ano: 2010
Número Páginas:
8p.
Autor(es): Oliveira, S.; Ferreira, I.; Berberan, A. L.; Mendes, P.; Boavida, J.; Baptista, B.
Keywords: Laser scan; Modal parameters; Concrete dams
Info
Monitorização e modelação estatística e numérica de vibrações devidas a desmonte com explosivos
Esta comunicação descreve um trabalho de monitorização e estudo da geração e propagação das vibrações produzidas por uma operação subaquática de desmonte de rocha que teve lugar no Porto de Leixões em 2006. Terminada a monitorização, que exigiu um acompanhamento cuidado dos impactos dos rebentamentos na malha urbana circundante, definiram-se leis empíricas de atenuação e um modelo de inteligência artificial (redes neuronais perceptrão multicamada) que forneceram estimativas da velocidade máxima de vibração em função da carga e da distância. Estes métodos tornaram possível a definição de distribuições espaciais de vibração para todo o desenrolar da obra. Finalmente, desenvolveu-se um modelo dinâmico de diferenças-finitas tridimensional de parte da obra, no qual foram estudados diversos cenários de geração e propagação. Este modelo permitiu, por uma lado extrair conclusões qualitativas interessantes sobre a propagação da vibração deste caso, e por outro comprovar a aplicabilidade da modelação numérica nesta classe de problemas, tanto em obras superficiais como em obras subterrâneas, tais como a escavação de túneis e cavernas em rocha.
Ano: 2010
Número Páginas:
11.
Autor(es): Resende, R.; Lamas, L.; Lemos, J. V.; Calçada, R.
Editor: Sociedade Portuguesa de Geotecnia
Keywords: Flac3d; Modelação numérica; Redes neuronais; Desmontes com explosivos; Vibrações
Info
Observação e análise do comportamento dinâmico da torre das tomadas de água da barragem do Cabril
A aplicação de modelos de identificação modal na análise de resultados de ensaios de vibração ambiental efectuados na barragem do Cabril (a maior barragem portuguesa - abóbada simples com 132 m de altura) mostrou a ocorrência de picos espectrais importantes, cuja frequência não correspondia às conhecidas frequências naturais da obra, tendo-se colocado a hipótese desses picos estarem relacionados com o comportamento dinâmico da torre das tomadas de água
Ano: 2010
Número Páginas:
11p.
Autor(es): Espada, M.; Mendes, P.; Oliveira, S.
Keywords: Identificação modal; Barragens de betão
Info
Observação em contínuo do comportamento dinâmico da barragem do Cabril
Neste trabalho apresentam-se os primeiros resultados obtidos com um sistema de observação do comportamento dinâmico instalado na barragem do Cabril, em que se mostra a evolução no tempo das primeiras quatro frequências naturais da obra durante um período de observação de cerca de um ano. Descreve-se um conjunto de rotinas implementadas para a identificação automática das frequências naturais da estrutura; a filosofia de gestão dos dados que são adquiridos em contínuo; o controlo remoto do sistema e a transmissão de dados via internet, entre o centro de controlo do sistema instalado em obra e o centro de análise situado no Laboratório Nacional de Engenharia Civil (LNEC). Este sistema, baseado na medição de vibrações em contínuo, permite a caracterização do comportamento dinâmico desta obra ao longo do tempo, tendo em conta os diversos tipos de excitação, tais como o vento, a vibração provocada pelo funcionamento dos grupos de produção de energia e dos órgãos de descarga, micro tremores e sismos de média e elevada intensidade.
Ano: 2010
Número Páginas:
12p.
Autor(es): Mendes, P.; Oliveira, S.
Keywords: Monitorização em contínuo; Comportamento dinâmico; Identificação modal; Barragens de betão
Info
Simulation of vibration generated by underwater blasting using statistical analysis and numerical modelling
Rock blasting in urban settings is always extremely demanding in what regards the control of ground vibrations and other environmental impacts. Extensive underwater blasting was performed in the Leixões Harbour, an important harbour surrounded by a dense urban mesh. Macro-seismometers were installed in the perimeter and recorded more than one thousand blasts. After completion of the works classical curve fitting statistical analysis of peak particle velocity (PPV) as a function of charge and distance to the blast was performed. PPV spatial distributions were determined for the duration of the construction and maps of ground peak vibration velocity drawn. The results showed that the accuracy of the attenuation law is within the usual range for this kind of phenomenon. However, factors like terrain morphology or geology variations cannot easily be included in a regression law but can be treated in a simple numerical model. A dynamic finite-difference model was developed and the influence of these features was studied thus increasing the understanding of the problem and providing valuable insights into some aspects of the usually large dispersion in the PPV.
Ano: 2010
Número Páginas:
313-316pp.
Autor(es): Resende, R.; Gomes, J. P.
Editor: CRC Press
Keywords: Modelação numérica; Numerical modelling; Vibrações; Vibration; Desmonte rocha; Rock blasting
Info
Strong discontinuities, mixed finite element formulations and localized strain injection, in fracture modeling of quasi-brittle materials
The presented work explores a combination of strain localization methods and strong discontinuity ap-proaches to remove the flaws (stress-locking and mesh bias dependence) of the classical strain localization methods, and reduce the sophistication of the strong-discontinuity based methods. The concept of strong discontinuity is initially substituted by that of weak discontinuity capturing the displacement jump through its distribution (smearing) in a finite length: the oriented with of a finite element through which the fracture passes in a rather diffuse manner. In other words, the classical strain localization concept is brought to the approach, no strong discontinuity enrichment is made and standard constitutive models are used in a classi-cal strain localization setting. The standard mesh refinement recovers the strong discontinuity concept by taking the element width to zero. However, in order to remove the spurious mesh orientation dependence, in a second stage specific localization modes are injected, via mixed finite elements formulations, to the path of elements that are going to capture the cracks. These modes, as well as their injection time, are character-ized from the information provided by the SDA. Then, the obtained approach enjoys the benefits of the strong discontinuities one, at a complexity similar to the classical, and simpler, localization methods.
Ano: 2010
Número Páginas:
381-389.
Autor(es): Oliver, J.; Dias, I. M.; Huespe, A.E.
Revista: Computational modelling of concrete Structures
Editor: CRC Press/Balkema
Keywords: fracture modeling; localized strain injection; mixed finite element formulations; Strong discontinuities
Info
A 3D Rigid Particle Model for Shear Transfer Analysis in Reinforced Concrete
A 3D spherical rigid particle discrete element formulation based on the Discrete Element Method, DEM, which has been used to model concrete, is described. The model has been shown to give a good agreement in terms of peak strength, fracture localization and crack patterns for various load conditions. An explicit formulation for the reinforcement model which allows the model to be applied to reinforced concrete is presented. The reinforced rigid particle model is validated against known shear transfer tests due to dowel action. It is shown that the model is able to predict the influence of the dowel stiffness and the localized fracture in the vicinity of the initial crack.
Ano: 2009
Número Páginas:
4.
Autor(es): Azevedo, N.; Lemos, J. V.; de Almeida, J.
Keywords: Discrete element; Reinforced concrete
Info
About the Determination of the In-Situ State of Stress
The paper presents the 2 main methods for the determination of the in-situ state of stress in rock masses, developed by the LNEC, and refers to a practical case in which they were used, at an underground powerhouse in northern Portugal.
Ano: 2009
Número Páginas:
4 p..
Autor(es): Grossmann, N.
Keywords: Ensaios in-situ; Estado de tensão; Mecânica das rochas
Info
Assessment of the seismic capacity of stone masonry
Abstract. The application of discrete element models based on rigid block formulations to theanalysis of masonry walls under horizontal out-of-plane loading is discussed. The problemsraised by the representation of an irregular fabric by a simplified block pattern are addressed.A test problem provides a comparison of various regular and random block patterns, showingtheir influence on the failure loads. An example of application of a rigid block model to a wallcapacity problem is presented.
Ano: 2009
Autor(es): Lemos, J. V.; Campos Costa, A.; Bretas, E. M.
Keywords: Rigid blocks; Discrete elements; Seismic assessment; Masonry structures
|
Livros
Info
Computational modeling of masonry structures using the discrete element method
Masonry is a combination of units such as stones, bricks or blocks usually laid in a cementitious or limemortar. It is probably the oldest material used in construction and has proven to be both simple to buildand durable. Over the years, existing masonry constructions have inevitably suffered damage with time.Earthquakes, soil settlements, material degradation and lack of maintenance are the main reasons forthat. Careful and periodic assessment of such structures is necessary in order to evaluate their structuralcapacity and safety levels. However, performing the structural analysis of masonry construction is notan easy task. A review is presented of the main models based on the discrete element method and the available related numerical techniques that have been proposed for the analysis of masonry. The essential assumptions adopted by these models and numerical implementation issues are discussed. Differences between available models are illustrated by applications to various masonry problems including static and dynamic analysis of masonry arch bridges, walls, vaults, domes and ancient colonnades.This book is composed of 17 chapters authored/co-authored by 25 outstanding researchers from 11countries (Canada, France, Greece, Hungary, Iran,Italy, Mexico, Norway, Portugal, UK, USA), whichwere reviewed by 60 referees.
Ano: 2016
Número Páginas:
505p.
Autor(es): Sarhosis, V.; Bagi, K.; Lemos, J. V.; Milani, G.
Editor: IGI Global
Keywords: Elementos discretos; Modelação numérica; Alvenaria
Info
Contribuição de Manuel Rocha para a mecânica das rochas e as fundações de barragens
N/A
Ano: 2013
Número Páginas:
296pp.
Autor(es): Lemos, J. V.; Lamas, L.
Editor: LNEC
Keywords: Investigação científica e técnica; Barragem de betão; Fundação rochosa; Fundação de barragem; Mecânica das rochas; Pt
|
Capítulos de Livros
Info
Chapter 5 Discrete Element Modeling
This chapter consists of two parts. First a general overview is given: the exact definition of the Discrete Element Method is provided, and the main types of existing models are introduced; then the theoretical fundaments of the most important approaches available today for masonry analysis are given. The second part of the chapter focuses on 3DEC, the most widespread commercial DEM code for masonry analysis. This second part begins with a theoretical overview. Application issues for masonry structures are then considered (block material behaviour, contact representation, structural elements like cables or bars etc.). Among the practical examples arches, barrel vaults, walls, coloumns and complete structures (like houses) are presented, including the issues of quasi-static versus dynamic analysis and of block fracture as well. The readers can find helpful advice on how to simulate their own problems most effectively.
Ano: 2023
Autor(es): Lemos, J. V.; Bagi, K.
Revista: Discrete Computational Mechanics of Masonry Structures
Editor: Springer
Keywords: Masonry models
Info
Discrete Element Modelling of Masonry Arch Bridges, Arches and Vaults
N/A
Ano: 2022
Autor(es): Lemos, J. V.; Gobbin, F.; Forgacs, T.; Sarhosis, V.
Revista: From Corbel Arches to Double Curvature Vaults.
Editor: Springer
Keywords: numerical modelling; masonry
Info
DEM modelling of the non-linear static and dynamic response of masonry structures
Discrete element models have become a major tool for masonry analysis, allowing a suitable representation of its discontinuous nature and marked nonlinear behaviour. The chapter reviews the fundamental assumptions of the main DEM formulations available. It focuses more specifically on the widely used UDEC and 3DEC codes, explaining their relation with the other approaches, and the most relevant issues arising in their application to masonry. Applications to the main types of structures are reviewed, considering both static and dynamic analyses. Recent research providing comparisons of the numerical models with experimental and field data is particularly covered. The discussion of the different examples is aimed at clarifying the key capabilities of DEM and demonstrating the most effective ways of using it in a variety of masonry analysis situations.
Ano: 2019
Número Páginas:
469-501pp.
Autor(es): Sarhosis, V.; Lemos, J. V.; Bagi, K.
Revista: Numerical Modeling of Masonry and Historical Structures - From Theory to Application
Editor: Elsevier
Keywords: DEM; Masonry structures
Info
Seismic and Structural Health Monitoring of Dams in Portugal
This chapter is focused on the Portuguese experience on the developmentand exploration of systems for continuously monitoring dam vibrations, usingaccelerometers. The pioneer system for seismic and structural health monitoring(SSHM) installed in Cabril dam (the highest Portuguese arch dam: 132 m high) isdescribed in detail. The design of this system was the result of a long-term LNECresearch program, still ongoing. These monitoring systems should include softwaredeveloped to automatically perform the analysis of collected data, including theautomatic comparison with numerical results from 3DFE models. In view of thegood results obtained with the system in operation in Cabril dam since 2008, similarsystems have been installed in other large dams in Portugal, particularly in recentlybuilt dams. Finally, Baixo Sabor dam is presented as an example of a new Portuguesedam with a complete SSHM system, in operation since 2015. Themain experimentalresults obtained for both dams are shown, namely the evolution of natural frequenciesover time, mode shapes and the measured seismic response to earthquake events.
Ano: 2019
Número Páginas:
87-113pp..
Autor(es): Oliveira, S.; Alegre, A.
Revista: Seismic Structural Health Monitoring - From Theory to Successful Applications
Editor: Springer
Keywords: Modal identification · Concrete dams · Ambient and seismic vibrations
|
Teses de Doutoramento
Info
Análise experimental de cenários de rotura em fundações de barragens de betão
Para verificação do cumprimento das exigências de segurança das barragens,tanto relativamente à funcionalidade (cenários correntes), como em relação àsegurança ao colapso (cenários de rotura), é essencial utilizar modelos de simulação oude interpretação (no caso de obras existentes) do seu comportamento. Estes modelossão idealizações (simplificações) da realidade, tanto no que diz respeito às acções(modelos das acções), como no que respeita à componente estrutural (modelos estruturais).A solução destes modelos, através de adequados métodos de análise, quantificaparâmetros da resposta das estruturas que permitem avaliar a sua segurança, utilizandocritérios de segurança previamente definidos.A validação destes modelos pode ser feita, no caso de cenários correntes,através da sua comparação com os resultados da observação do comportamento debarragens. No caso de cenários de rotura, não existe muita experiência de comparaçãodestes resultados com situações reais: é pequeno o número de acidentes ocorrido e,mesmo nestes, o volume de informação é reduzido. Desta forma, o recurso a métodosexperimentais, para o estudo de cenários de rotura, tem uma importância acrescida.Assim o principal objectivo deste trabalho é contribuir para melhorar a capacidade deavaliação da segurança de barragens de betão envolvendo cenários de rotura pela fundação.Neste trabalho desenvolveram-se dois ensaios experimentais em modelosfísicos: um primeiro envolvendo uma barragem abóbada, para o estudo de cenários derotura da fundação para acções estáticas; e um segundo de uma barragem gravidadeensaiado em mesa sísmica, com vista a estudar a rotura pela fundação para acçõesdinâmicas.A previsão e interpretação dos ensaios foram efectuadas com modelosmatemáticos adequados, que permitiram a sua validação e posterior utilização no estudode outros cenários.
Ano: 2009
Autor(es): Gomes, J. P.
Keywords: Método dos elementos discretos; Método dos elementos finitos; Modelos numéricos; Mesa sísmica; Análise dimensional; Modelos físicos; Análise até à rotura; Controlo da segurança de barragens; Barragens de betão
|
|
Relatórios
Info
Barragem do Cabril - Sistema para monitorização de vibrações em contínuo medição e análise automática da resposta dinâmica sob excitação ambiente/operacional e sob ações sísmicas
Neste trabalho apresenta-se o sistema para monitorização em contínuo do comportamento dinâmico da barragem do Cabril que foi instalado em 2008, pelo LNEC e pela EDP, referindo alguns dos principais resultados que têm sido obtidos a partir da análise dos dados recolhidos, quer sob excitação ambiente/operacional, quer sob ações sísmicas. Salienta-se a importância do desenvolvimento do software para tratamento, análise e gestão automática dos dados e apresentam-se os programas que têm vindo a ser desenvolvidos no LNEC, em MATLAB, para apoio a este tipo de sistemas, nomeadamente programas de identificação modal (Modal_ID2.0 e Modal_ID_Auto2.0) e programas de elementos finitos tridimensionais para análise do comportamento dinâmico de sistemas barragem-fundação-albufeira (DamDySSA2.0).
Ano: 2017
Autor(es): Oliveira, S.; Silvestre, A.
Keywords: Densidade espetral de potência; Amortecimentos modais; Comportamento dinâmico de barragens; Modos de vibração; Frequências naturais; Interação dinâmica barragem-albufeira; Análise espetral; Monitorização de vibrações em contínuo
Info
Discrete element modelling of rock engineering structures for seismic safety analyses - PhD thesis research plan of Margarida Espada
This document presents the research plan for the doctoral thesis of LNEC's Junior Research Fellow Margarida Espada. This work, to be submitted to the Faculty of Engineering of the University of Porto (FEUP), will be developed in the Modelling and Rock Mechanics Unit of the Concrete Dams Department, and it is part of the on-going P2I research project DEMRock6m. This work aims at developing more efficient methodologies to perform safety studies and seismic analysis of rock engineering structures, based on discrete element models and in the integrated use of probabilistic models for the geometric and shear strength parameters and for the water pressures in rock discontinuities. This will allow a more realistic definition of the rock mass in discrete element models and an adequate identification of the potential failure mechanisms.
Ano: 2016
Autor(es): Espada, M.; Muralha, J.; Lemos, J. V.; Couto Marques, J.
Keywords: Dam foundations; Rock discontinuities; Seismic analysis; Probabilistic analysis; Safety analysis; Discontinuities generation tool; Discrete element models
Info
Método de Euler não linear aplicado a órbitas do sistema n-CORPOS
Neste relatório é apresentado o método de Euler para calcular as órbitas do sistema n-corpos,por exemplo, o dos planetas do sistema Solar, tendo em conta a propagação das forçasgravíticas entre o Sol e os planetas e entre os planetas entre si. Apenas requer como dadosiniciais uma observação anterior das órbitas em termos de posição e velocidade. A correcçãoda interacção entre planetas não é suavizada, o que se justifica pelos seus valores. A correcçãorelativista é importante.
Ano: 2013
Número Páginas:
11pp.
Autor(es): Câmara, R.
Editor: LNEC
Info
Soluções distribucionais das equações de Navier-Stokes
As equações de Navier-Stokes são equações de derivadas parciais. As incógnitas nocaso de incompressibilidade consistem no campo de velocidades. As pressões numa 1ªaproximação resultam de um equilíbrio estático.A principal causa de problemas relacionados com a solução destas equações é devida àparcela das acelerações convectivas que está na origem da turbulência.Pesando estas equações e integrando duas vezes por partes obtém-se uma forma fracadestas equações.Em problemas 3D as variáveis independentes são 3 espaciais e 1 temporal. Admite-seque o campo de velocidades pode ser desenvolvido em série de distribuições de Delta deDirac espaciais e suas derivadas com coeficientes funções do tempo. Com funções deteste polinomiais obtém-se a formulação distribucional proposta das equações deNavier-Stokes.
Ano: 2013
Número Páginas:
15pp.
Autor(es): Câmara, R.; Azevedo, N.
Editor: LNEC
Info
Análise térmica de barragens de betão - Ações térmicas ambientais
N/A
Ano: 2012
Número Páginas:
114pp.
Autor(es): Leitão, N. S.
Editor: LNEC
Info
Ondas esféricas quânticas
O objectivo deste relatório é o estudo da matemática aplicada à solução de problemasfísicos de propagação de ondas esféricas com operador espacial biharmónico,consideradas quânticas.As técnicas matemáticas usadas incluem a transformada de Laplace da função de ondaf e o cálculo de sua inversa tal como sugerida por Pipes e Harvill.O método matemático usado para descrever as ondas esféricas quânticas é compequenas adaptações o método causal não-linear descrito por Croca.
Ano: 2011
Número Páginas:
12pp.
Autor(es): Câmara, R.
Editor: LNEC
Info
Tópicos sobre equações de derivadas parciais
N/A
Ano: 2011
Número Páginas:
15pp.
Autor(es): Câmara, R.
Editor: LNEC
Info
Ensaios de juntas de argamassa para um modelo físico de uma barragem abóbada a ensaiar na mesa sísmica
N/A
Ano: 2009
Número Páginas:
64pp.
Autor(es): Muralha, J.
Info
RADIAÇÃO SÍSMICA DUMA FALHA PARA UMA BARRAGEM ABÓBADA
N/A
Ano: 2007
Número Páginas:
50pp.
Autor(es): CÂMARA, R.
Info
Geração de malhas de elementos finitos tridimensionais. Desenvolvimento e apresentação do módulo computacional GeTMEF1.0
A análise do comportamento de barragens de betão com base em modelos de elementos finitos tridimensionais exige a definição da discretização a adoptar para o conjunto barragem-fundação, ou barragem-fundação-albufeira. A realização desta tarefa sem o recurso a programas de geração automática é muito dispendiosa pelo que tem vindo a ser desenvolvido no NMMF um módulo computacional para geração automática de malhas de elementos finitos tridimensionais especialmente adaptado para a geração de malhas tridimensionais de barragens abóbada. Inicialmente desenvolvido em FORTRAN, o referido módulo computacional para geração de malhas de elementos finitos tridimensionais tem vindo a ser objecto de diversos melhoramentos, os mais recentes centrados ao nível da interface com o utilizador. Assim, apresenta-se neste relatório o módulo computacional
Ano: 2006
Autor(es): Dias, I. M.; Oliveira, S.
Keywords: Barragens; Hexaedros; Geração de malhas de elementos finitos
|
Informações Científicas e Técnicas
Info
Identification of transversely isotropic parameters in overcored rock specimens - A back analysis approach
This document presents a back analysis procedure for identification of the elastic parameters of transversely isotropic rock cores, containing an overcoring triaxial strain probe, from the strains measured during a biaxial test. A three-dimensional finite element model was developed to simulate the biaxial test on the overcored rock specimen and to compute the strains at the location of the strain gauges. Different optimisation algorithms were tested and the most suitable one was selected. The back analysis procedure was tested for identification of the five elastic parameters and the two orientation angles that characterise a transversely isotropic rock core. In spite that, with the developed methodology, convergence was reached and all those parameters could be identified, sensitivity analyses demonstrated that the results obtained were not stable and therefore they were not reliable. By introducing constrains based on common practice and previous experience, a stable and robust methodology was achieved: the three elastic parameters, E1, E2 and ?2, are reliably identified using the value of G2 calculated with Saint-Venants expression and a fixed value of ?1, while the orientation parameters are obtained from observation of overcored rock. Analysis of the results shows that application of this methodology represents an enormous step forward when compared with the traditional use of isotropy. Besides, the methodology is general and can also be used with other types of overcoring equipment. The five elastic parameters and the two orientation angles obtained can then be used, together with the overcoring strains, to compute the complete in situ state of stress.
Ano: 2018
Autor(es): Espada, M.; Lamas, L.
Keywords: Transversely isotropic rock; Numerical method; Rock test; Optimisation; Triaxial strain probe; In situ stress; Overcoring; Biaxial test
Info
Stability analysis of excavation slopes of Baihetan arch dam foundation - Reliability analysis by application of the response surface method
This document presents the work developed by the PhD student Margarida Espada in the scope of the course unit Risk Analysis in Geotechnical Works of the Doctoral Program in Civil Engineering of the Faculty of Engineering of the University of Porto (FEUP). This work presents a reliability analysis, using the response surface method (RSM), for the case study of the left bank excavation slopes of the Baihetan arch dam foundation, which is one of the case studies of Margarida Espada's PhD thesis. The aim was to approximate an implicit limit state function by computing safety factors, using a discrete element model of the Baihetan left bank developed in 3DEC software, where the shear strength parameters of two important rock discontinuities were considered as random variables. The probability of failure was then obtained through an iterative process, using approximation methods. This work presents the 3DEC model developed to analyse the stability conditions in the Baihetan left bank and the results of the reliability analysis.
Ano: 2018
Autor(es): Espada, M.
Keywords: Dam foundation; Baihetan dam; Discrete element method; Reliability; Slopes stability
Info
Contribuição para o problema da existência e suavidade da solução da equação de Navier- Stokes
O problema da solução das equações de Navier Stokes é abordado neste trabalhopropondo-se uma técnica de representação das incógnitas deslocamentos e pressõesvariáveis no espaço e no tempo em série de Delta de Dirac e suas derivadas no tempocujos coeficientes se determinam com base na solução de sistemas de equaçõesdiferenciais definidos no espaço (problema com três variáveis espaciais independentesque pode ser estudado pelo método de Monge).
Ano: 2011
Número Páginas:
12pp.
Autor(es): Câmara, R.
Editor: LNEC
Keywords: Equação de navier-stokes
Info
Elastodinâmica
Neste relatório apresentam-se as equações básicas da elastodinâmica linear, as soluçõesfundamentais e o teorema da representação no domínio de tempo e de frequência.Para movimentos finitos de casca formula-se o teorema dos trabalhos virtuais e a suaimplementação pelo método dos elementos finitos.
Ano: 2007
Número Páginas:
54pp.
Autor(es): Câmara, R.
Editor: LNEC
Keywords: Método dos elementos finitos; Elastodinâmica
Info
Modelação sísmica de barragens abóboda
Neste relatório apresentam-se os principais aspectos da modelação sísmica de barragensabóbada. Assim propõe-se: modelos numéricos de geração de sismos por uma falha; aforma como o sismo actua na barragem; modelos para estudar a influência da albufeirana vibração do conjunto; métodos para solução das equações do movimento; e novasformulações de elementos finitos para o problema estrutural.
Ano: 2005
Número Páginas:
72pp.
Autor(es): Câmara, R.
Editor: LNEC
Keywords: Método dos elementos finitos; Simulação numérica; Comportamento sísmico de estruturas; Comportamento de barragens; Barragem abóboda
Info
An experimental and numerical study for analysis of the hydromechanical behavior of the Alto Lindoso high pressure circuit
In pressure tunnels and shafts, in addition to the mechanical effect that excavation has on the rock mass and the disturbance that it introduces in the water flow, also the contained water can interact from the mechanical and hydraulic points of view with the rock mass. Seepage in fractured rock masses is dominated by the flow that takes place through the joints, and this is highly d(;pendent on their properties, namely aperture and roughness. Joint aperture, in tum, i::; very sensitive to stress changes. Special attention must therefore be paid to the joints in hydromechanical analyses. In this report are presented some studies that were carried out for the hydromechanical characterization of joints of the Alto Lindoso rock mass and numerical simulations of the hydromechanical behaviour of two selected sections of the high pressure circuit.
Ano: 1994
Autor(es): Lamas, L.
Keywords: Simulação numérica; Barragem de Alto Lindoso; Percolação no solo; Maciço rochoso; Comportamento hidromecânico; Interacção solo-água-estrutura; Circuito hidráulico
|
|
|