Artigos de Revista
Info
Experimental investigation on the power capture of an oscillating wave surge converter in unidirectional waves
The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.
Ano: 2019
Número Páginas:
975-992pp.
Autor(es): Brito, M.; Ferreira, R. L.; Teixeira, L; Neves, M. G.; R. Canelas
Revista: Renewable Energy
Editor: Elsevier
Volume:
Volume 151.
Keywords: Power take-off: PTO damping; Response amplitude operator: RAO; Capture width ratio: CWR; Oscillating wave surge converter: OWSC; Wave energy
Info
Measuring wave run-up, overtopping and damage of rubble-mound breakwaters in scale model tests
A set of scale-model tests was carried out at the wave basin of the Leibniz University Hannover to extend the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater
Ano: 2019
Número Páginas:
118-129pp.
Autor(es): Santos, J. A.; Lemos, R.; Weimper, J.; Gronz, O.; Hofland, B.; Sande, J.; Pinheiro, L.; Spans, J.H.; Peña, E.; Reis, M. T. L. G. V.; Fortes, C. J. E. M.; Figuero, A.; Laiño, E.; Bornschein, A.; Kerpen
Editor: Hydralab+
Keywords: Rubble-mound breakwaters; Model tests; Overtopping; Wave run-up
Info
Numerical analysis of the interference between two elastically mounted cylinders in tandem subject to flows at low Reynolds numbers
Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.
Ano: 2019
Número Páginas:
11p.
Autor(es): Teixeira, P.; Rechsteiner, P.; Didier, E.
Revista: Journal of the Brazilian Society of Mechanical Sciences and Engineering
Editor: Springer
Volume:
Vol. 41.
Keywords: Finite element method; Vortex-induced vibration; Wake interference; Tandem arrangement; Circular cylinders
Info
Observação e monitorização de obras marítimas com a nova metodologia OSOM+
This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira
Ano: 2019
Número Páginas:
22p.
Autor(es): Fortes, C. J. E. M.; Capitão, R.; Henriques, M. J.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Silva, L. G.
Revista: Revista Mundi, Engenharia, Tecnologia e Gestão
Editor: Instituto Federal do Paraná
Volume:
v.4, n.2.
Keywords: Ericeira
Info
A methodology to determine the optimal size of a wells turbine in an oscillating water column device by using coupled hydro-aerodynamic models
This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.
Ano: 2018
Número Páginas:
9-18pp.
Autor(es): Torres, F.; Teixeira, P.; Didier, E.
Revista: Revista Renewable Energy
Editor: Elsevier
Volume:
Vol. 121.
Keywords: Air pressure control; Turbine sizing; Oscillating water column; Wave energy
Info
An integrated tool for modelling oscillating water column (OWC) wave energy converters (WEC) in vertical breakwaters
This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.
Ano: 2018
Número Páginas:
198
Autor(es): Mendonça, A. C.; Dias, J.; Didier, E.; Fortes, C. J. E. M.; Neves, M. G.; Reis, M. T. L. G. V.; Conde, J. M.; Poseiro, P.; Teixeira, P. R. F.
Revista: Journal of Hydro-environment Research
Editor: Elsevier
Volume:
Vol. 19.
Keywords: Wave power; SWAN-URANS models; Nonlinear numerical modelling; Physical modelling; Wave-structure interaction; Oscillating water column (OWC) wave energy converter (WEC)
Info
Asymmetric copula
Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula
Ano: 2018
Número Páginas:
304-334pp.
Autor(es): Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Vanem, E.; Reis, M. T. L. G. V.; Neves, L.
Revista: Wind Engineering
Editor: Sage
Volume:
Vol. 42, No. 4.
Keywords: Asymmetry; Crámer
Info
Characterization of ship motions induced by wake waves
This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the
Ano: 2018
Número Páginas:
547-555pp.
Autor(es): Pedro, F.; Pinheiro, L.; Fortes, C. J. E. M.; Santos, J. A.; Hinostroza , M.
Revista: Progress in Maritime Technology and Engineering
Editor: Taylor & Francis
Keywords: Wake waves; SWAMS; Ship motions
Info
Coastal risk forecast system
The run-up and overtopping by sea waves are two of the main processes that threaten coastal structures, leading to flooding, destruction of both property and the environment, and harm to people. To build early warning systems, the consequences and associated risks in the affected areas must be evaluated. It is also important to understand how these two types of spatial information integrate with sensor data sources and the risk assessment methodology. This paper describes the relationship between consequences and risk maps, their role in risk management and how the HIDRALERTA system integrates both aspects in its risk methodology. It describes a case study for Praia da Vito´ria Port, Terceira Island, Azores, Portugal, showing that the main innovations in this system are twofold: it represents the overtopping flow and consequent flooding, which are critical for coastal and port areas protected by maritime structures, and it works also as a risk assessment tool, extremely important for long-term planning and decision-making. Moreover, the implementation of the system considers possible known variability issues, enabling changes in its behaviour as needs arise. This system has the potential to become a useful tool for the management of coastal and port areas, due to its capacity to effectively issue warnings and assess risks.
Ano: 2018
Número Páginas:
26p.
Autor(es): Sabino, A.; Poseiro, P.; Rodrigues, A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Reis, R.; Araújo, J
Revista: Journal of Geographical Systems
Editor: Springer
Keywords: Software product lines; Geographic information systems; Early warning; Risk management; Coastal flooding; Wave overtopping
Info
Estudos em modelo reduzido de obras marítimas da Região Autónoma dos Açores
Atendendo ao seu caráter histórico, o presente artigo insere-se num conjunto de ações proposto pelo Departamento de Hidráulica e Ambiente (DHA) do Laboratório Nacional de Engenharia Civil (LNEC) com vista à comemoração dos 70 anos da sua existência, efeméride que se comemora durante o presente ano de 2018, e visa a apresentação de uma resenha da atividade desenvolvida no âmbito de estudos em modelos físicos de obras marítimas, pelo DHA desde a sua fundação, e para a Região Autónoma dos Açores (RAA). Pela sua insularidade, as populações da (RAA) estão naturalmente ligadas ao mar, nas suas mais diversas vertentes, muito dependendo a sua qualidade de vida das infraestruturas portuárias existentes em cada ilha, que permitem os indispensáveis movimentos de pessoas e de mercadorias e que muito contribuem para a coesão social e económica do arquipélago.Em virtude do papel decisivo assumido pelos portos na RAA, foi ao longo dos anos dada especial atenção à concepção destes equipamentos infraestruturais, tendo o LNEC desempenhado um papel relevante no capítulo reservado à verificação de projetos de obras marítimas de proteção portuária, especialmente através da realização de estudos em modelo físico reduzido, enquanto ferramenta mais válida para a concretização daquele objetivo, quer no passado, quer também no presente. Desde a fundação do Serviço de Hidráulica do LNEC, em 1948, foram inúmeros os estudos em modelo físico reduzido realizados para obras marítimas da RAA. O primeiro estudo em modelo reduzido de que há registo foi iniciado na segunda metade da década de 50, tendo o respetivo relatório do estudo sido publicado em março de 1958. Tratou-se de um estudo em modelo reduzido tridimensional (3D) com vista à definição do lay-out das obras marítimas de proteção do porto de Vila do Porto (Ilha de Santa Maria), em estrito cumprimento de requisitos que haviam sido estabelecidos, do ponto de vista da agitação marítima no interior da bacia portuária.Desde então, o LNEC foi chamado a intervir com a realização de ensaios em modelo reduzido em múltiplas situações, tendo-se assistido a uma especial concentração de atividade a partir do início da década de 80, coincidindo com o grande desenvolvimento portuário registado na Região.Ao longo dos 70 anos de vida do Departamento de Hidráulica e Ambiente (DHA) foram então efetuados, no LNEC e sob a orientação dos seus técnicos, 50 estudos em modelo físico reduzido de obras projetadas para a RAA, para todas as ilhas do arquipélago, com exceção da Ilha do Corvo.
Ano: 2018
Número Páginas:
24-31pp.
Autor(es): Silva, L. G.
Revista: Construção Magazine
Editor: Engenho e Média, Lda
Volume:
85.
Keywords: Portos; Modelação física; Açores
|
Comunicações
Info
O papel da modelação física no apoio aos estudos de engenharia costeira e portuária. Desafios e oportunidades
Neste artigo, apresenta-se uma descrição do papel da modelação física no apoio aos estudos de Engenharia Costeira e Portuária, ilustrando-se as suas potencialidades com exemplos de casos de estudo.Referem-se os contributos inovadores em conceitos, equipamentos, técnicas e procedimentos experimentais que têm sido desenvolvidos nos recentes anos. Assim, apresentam-se metodologias a explorar no futuro, tais como procedimentos destinados a facilitar, agilizar e automatizar as análises de estabilidade e galgamentos de quebra-mares, assim como dos danos no manto protetor, provocados pela agitação marítima nele incidente, e o acesso remoto a ensaios experimentais, e à informação associada à realização destes, a clientes/investigadores interessados.Por fim, são apontados cenários de desenvolvimento para a modelação física de modo a lidar com as consequências das alterações climáticas, e que incorporem: a) sequências de eventos de temporal, incluindo efeitos cumulativos, b) a subida do nível médio do mar; c) técnicas de medição não intrusivas que permitam obter a análise de fenómenos complexos, com características de grande variabilidade temporal e espacial, sem interferir nos mesmos ou no próprio sistema modelado.
Ano: 2016
Número Páginas:
13p.
Autor(es): Fortes, C. J. E. M.; Capitão, R.; Lemos, R.; Neves, M. G.; Pinheiro, L.; Reis, M. T. L. G. V.
Editor: LNEC
Keywords: Engenharia costeira e portuária; Desafios e oportunidades; Casos de estudo; Modelação física
Info
Otimização da arquitetura computacional do sistema HIDRALERTA
A presente comunicação descreve o conjunto de procedimentos adotados para tornar maisfuncional, eficiente e fidedigno o sistema de previsão e alerta de galgamentos em zonascosteiras e portuárias - HIDRALERTA. Estes procedimentos incidiram essencialmente emdois módulos do sistema: o módulo de caraterização da agitação marítima e o módulo dosistema de alerta, que inclui a plataforma Web.O módulo da agitação marítima requer maior capacidade de processamento, e, por isso, foimigrado para o Cluster MEDUSA possibilitando a execução paralelizada dos vários modelosnuméricos de geração, propagação e deformação da agitação marítima em zonas costeirase portuárias. A execução paralelizada permite um aumento da resolução temporal dasprevisões do sistema sem comprometer a rapidez de processamento.A plataforma Web permite dois tipos distintos de visualização diária de resultados: imagensestáticas, que contêm resultados dos modelos numéricos, e um WebGIS, que visa umarápida, eficiente e detalhada análise das previsões do HIDRALERTA. Nesta plataforma foiainda criada uma ferramenta de validação, acessível ao utilizador, que compara os dados daboia ondógrafo da Praia da Vitória (mantida parcialmente através do projecto ESTRAMARMAC/3/C177) com os valores calculados pelo sistema, conferindo uma maior confiança aosresultados do HIDRALERTA. O sistema de alerta foi também desenvolvido de forma aenviar alertas via E-mail. Nos casos que o justifiquem, um alerta emitido automaticamentepelo HIDRALERTA é enviado às entidades competentes, informando-as, com a maiorantecipação possível, das zonas/atividades em risco.
Ano: 2016
Número Páginas:
13p.
Autor(es): Lopes, P.; Poseiro, P.; Fortes, C. J. E. M.; Reis, M. T.; Garcia, T.; Azevedo, E. B.; Rodrigues, M. C.; Rodrigues, A.; Sabino, A.
Editor: APRH
Keywords: Sistemas de informação geográfica; Paralelização computacional; Sistema de alerta; Previsão em tempo real
Info
Overtopping risk evaluation at the portuguese coast: Leixões, Lisbon/Caparica and Sines study cases
To tackle recurrent emergency situations due to adverse sea wave conditions, often observed in Portuguese ports and coasts, a research project (HIDRALERTA) is underway to build a methodology and a system for long-term planning, wave climate forecast and early warning to be applied to those areas. This system deals with phenomena such as run-up, overtopping and flooding. lt wiII eventually empower the nationa! authorities with tools or systems that allow proper identification of risk areas and emergency situations and enable coastal and port authorities to select adequate and timely measures as to avoid Ioss of lives and minimize damages Iikely to arise from emergency situations. This system is now operative and has been already applied to several places along the coast of Portugal.
Ano: 2016
Número Páginas:
301-313pp.
Autor(es): Capitão, R.; Fortes, C. J. E. M.; Santos, J. A.; Poseiro, P.; Reis, M. T. L. G. V.; Pereira, T.
Editor: EdiBios
Keywords: Flooding; Wave climate; Risk; Overtopping
Info
Previsão e validação de galgamentos oceânicos no sistema HIDRALERTA.
São apresentadas algumas das técnicas de validação em curso para o sistema de previsãoe alerta de galgamentos oceânicos no porto e na baía da Praia da Vitória, Ilha Terceira,Açores. Através de hindcast, demonstra-se a capacidade do sistema HIDRALERTA emreproduzir eventos históricos responsáveis pela ocorrência de grandes galgamentos, comosucedido durante um grande temporal em 2001, em que as condições de agitação marítimae consequentes galgamentos originaram a destruição parcial do molhe Sul do porto. Atravésde forecast, comparam-se previsões diárias do sistema com dados de bóia-ondógrafo e cominformações in situ fornecidas por observadores locais, validando assim diariamente osistema. Este procedimento está em curso desde o início do Inverno marítimo de 2015/16. Acomparação dos resultados de hindcast e forecast com, respectivamente, dados históricos eobservações, permite concluir que o sistema representa uma ferramenta fiável no processode tomada de decisão relativamente à gestão de risco e intempéries em zonas costeiras eportuárias.
Ano: 2016
Número Páginas:
14p.
Autor(es): Garcia, T.; Reis, M. T.; Poseiro, P.; Fortes, C. J. E. M.; Lopes, P.; Lourenço, I.; Azevedo, E. B.; Rodrigues, M. C.
Editor: APRH
Keywords: Açores; Praia da Vitória; Validação; HIDRALERTA; Sistema de previsão e alerta; Galgamentos oceânicos
Info
Probability of failure of monopile foundations based on laboratory measurements
Monopile foundations are in the lead as the most common offshore substructure worldwide. Therefore, the study of their behaviour and the optimisation of their design represent important contributions, for the development of the offshore wind sector. In order to optimise the design process of monopiles in the marine environment, it is important to account for the uncertainties that can affect these structures, namely those relating to scour phenomena and the means of scour protection. Uncertainty relating to scour can be handled by means of statistical approaches. Probabilistic design methods may enable the optimisation of design procedures.This paper combines several results from physical modelling of scour development and a probabilistic model has been applied and extended to obtain probabilities of failure for the monopiles tested. This investigation will be used for comparison and calibration of the next phase of research, with a similar probabilistic approach being extended for waves and currents combined. The results presented are also used to provide an insight into future research concerning the failure of scour protection schemes. The relationship between safety factors and probabilities of failure of the monopiles is also presented.
Ano: 2016
Número Páginas:
10p.
Autor(es): Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Simons, R.; Reis, M. T. L. G. V.; Neves, L.
Editor: University of Ottawa
Keywords: Safety factor; Probability of failure; Monopile foundations; Monte Carlo; Scour
Info
Propagação de ondas em canal de largura variável
O presente trabalho visa estudar numericamente a influência de uma alteração da configuração em planta de um canal na propagação de ondas. Para tal, foi utilizado o modelo OpenFOAM® baseado nas equações RANS (Reynolds
Ano: 2016
Número Páginas:
151-154pp.
Autor(es): Neves, D. R.; Pires Silva, A.; Fortes, C. J. E. M.; Matos, J.S.G.
Editor: Instituto Hidrográfico
Keywords: Estreitamento; RANS; OpenFoam; Canal de ondas numérico; Propagação de onda
Info
Recentes desenvolvimentos da base de dados ANOSOM - análise da observação sistemática de obras marítimas
Os quebra-mares de talude são estruturas normalmente utilizadas para proteção portuária eestão sujeitas durante a sua vida útil a diferentes solicitações (p.e., agitação marítima). Aavaliação do seu estado estrutural e a previsão do seu comportamento ao longo do tempotorna-se um assunto fundamental de modo a evitar significativos prejuízos materiais.É nesse âmbito que se insere o programa de observação sistemática, em curso no LNEC,desde 1986, para quebra-mares localizados em Portugal Continental, no qual o LNEC efetuainspeções periódicas e avalia as condições de segurança de cada quebra-mar, bem como oestado de risco da estrutura com vista à melhor gestão das operaçõesmanutenção/reparação.Para apoio a esse programa desenvolveu-se a aplicação informática ANOSOM, emMicrosoft Access
Ano: 2016
Número Páginas:
13p.
Autor(es): Lemos, R.; Fortes, C. J. E. M.; Lopes, P.
Editor: APRH
Keywords: Quebra-mares; Obras marítimas; Observação sistemática; Base de dados
Info
Run-up on a rubble mound breakwater: comparison of empirical formulae and physical model results
The present study focuses on the comparison of measured wave run-up values obtained in physical model tests with those predicted by different empirical formulae. Tests were carried out in a flume for a cross-section of a rubble mound breakwater with an armour layer of tetrapods and rock, and a recurved wave return wall. The model represents the cross-section of the south breakwater of Praia da Vitória harbour (Azores, Portugal) that directly protects quay 12. Two water levels and several incident wave conditions were tested. Empirical runup formulae from Van der Meer & Stam (1992), Pullen et al. (2007) and Bonakdar & Etemad- Shahidi (2011) were applied for the tested conditions and comparisons were made with experimental values of the two percent wave run-up, R2% . Generally, the agreement between predictions and measurements was better for mean low water than for mean high water springs, with all formulae over predicting measurements for the latter.
Ano: 2016
Número Páginas:
12p.
Autor(es): Poseiro, P.; Reis, M. T. L. G. V.; Lemos, R.; Fortes, C. J. E. M.; Garcia, T.
Editor: LNEC
Keywords: South breakwater of Praia da Vitória; Empirical formulae; Physical modelling; Run-up
Info
Ship movements
A set of physical model tests was run in to characterize the ship
Ano: 2016
Número Páginas:
492-501pp.
Autor(es): Pinheiro, L.; Simão, J.; Santos, J. A.; Fortes, C. J. E. M.
Editor: Universidade Federal do Rio Grande (FURG)
Keywords: WAMIT; Physical model; Ship movements
Info
Ship movements' analysis in a scale model
A set of physical model tests was run in order to characterize the ship
Ano: 2016
Número Páginas:
12p.
Autor(es): Simão, J.; Pinheiro, L.; Lesme, H.; Hinostroza , M.; Santos, J. A.; Fortes, C. J. E. M.
Editor: LNEC
Keywords: Maritime agitation; Movements of the ship; Experimental test
|
|
Capítulos de Livros
Info
Multi-functional artificial reefs for coastal protection
N/A
Ano: 2009
Número Páginas:
153-210 pp.
Autor(es): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Teses de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Ano: 1999
Número Páginas:
159 p.
Autor(es): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Ano: 1998
Número Páginas:
594 p.
Autor(es): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Ano: 1998
Número Páginas:
346 p.
Autor(es): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Ano: 1973
Autor(es): Carvalho, M. M.
Editor: ******
|
|
Relatórios
Info
D1.1: Analysis of past extreme events, lessons learned ans SoA models V1
C2IMPRESS is a multi-disciplinary project which aims to enhance understanding and public awareness on multi-hazard risk, based on innovative models, methods, frameworks, tools and technologies to develop decision-making platforms with a fine-grained spatio-temporal data to better assess impacts, vulnerability and resilience on natural hazards. This Report is the Deliverable 1.1 and belongs to Work Package 1, which is mainly addressed to identify the past climate and physical processes that underlie natural disaster events and their consequences
Ano: 2023
Autor(es): Moragues, A.; Estrany, J.; Alves, E.; Zózimo, A. C.; Leitão, T. E.; Ruiz, M.; Oliveira, M. M.; Sfetsos, A.; Fernandes, T. F.
Info
Demonstration and technical tours plan
A major objective of TRA LISBON 2022 Conference is to boost research and innovation capacity for the transport sector, throughout a full innovation cycle, from idea to market. Having this in view, the project
Ano: 2022
Autor(es): Batista, F. A.; Marecos, V.; Antunes, M. L.; Macedo, A. L.; Freire, A. C.; Capitão, R.; Arsénio, E.; Maia, L.
Info
Demonstration submission and selection guidelines
The demonstration area will be one of the main focus points of TRA LISBON 2022, presenting multifunctional spaces and being prepared to receive a large number of different types of on-site demonstrations (indoor and outdoor). On-line demonstrations will also be an option, allowing for the widest possible coverage of access for all the participants.The dedicated areas will allow for interactive demonstrations of technological innovations to be carried out by and for industry partners, researchers, and other stakeholders. Demonstrations are an excellent opportunity to introduce conference attendees in an engaging way, as well as to promote new contacts and promising business.
Ano: 2022
Autor(es): Freire, A. C.; Arsénio, E.; Macedo, A. L.; Antunes, M. L.; Capitão, R.; Belinha, M.
Info
Technical tours organization criteria and procedures report
According to the CSA project plan, WP5.2 task objective is to organize technical tours that feature attractive and interactive showcases aiming at engaging participants into novel technologies for all transport modes and enabling stakeholders and their companies to disseminate and even sell their products and applications to all interested parties.
Ano: 2022
Autor(es): Capitão, R.; Macedo, A. L.; Arsénio, E.; Antunes, M. L.; Freire, A. C.
Editor: TRA LISBON 2022
Info
Data Repository Rules. Deliverable 10.4
This report is part of HYDRALAB+ Work Package 10, which seeks to strengthen the coherence of experimental hydraulic and hydrodynamic research undertaken by the HYDRALAB+ partner organisations. It outlines the work carried out by Samui Design & Management Ltd, supported by HR Wallingford, in relation to the development of a data repository structure that can be adopted by participants of the HYDRALAB+ project.
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data from physical modeling; Zenodo; Data repository structure
Info
Data Storage Report. RECIPE Task 8.2: Overtopping events in breakwaters under climate change scenarios
Reliable prediction of wave run-up/overtopping and structure damage is a key task in the design and safety assessment of coastal and harbor structures. Run-up/overtopping and damage must be below acceptable limits, both in extreme and in normal operating conditions, to guarantee the stability of the structure and the safety of people and assets on and behind the structure. The mean-sea-level rise caused by climate change and its effects on wave climate may increase the number and intensity of run-up/overtopping events and make the existing coastal/harbor structures more vulnerable to damage.Accurate estimates, through physical modelling, of the statistics of overtopping waves for a set of climate change conditions, are needed. The research project HYDRALAB+ (H2020-INFRAIA-2014-2015) gathers an advanced network of environmental hydraulic institutes in Europe, which provides access to a suite of environmental hydraulic facilities. They play a vital role in the development of climate change adaptation strategies, by allowing the direct testing of adaptation measures and by providing data for numerical model calibration and validation. The use of physical (scale) models allows the simulation of extreme events as they are now, and as they are projected to be under different climate change scenarios.The enclosed dataset refers to the experimental work developed at LNEC within HYDRALAB+ and considers 2D damage and overtopping tests for a rock armor slope, with four different approaches to represent storms. Data of free surface elevation, overtopping and damage is presented.
Ano: 2018
Autor(es): Fortes, C. J. E. M.; Mendonça, A. C.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Capitão, R.
Keywords: Climate change; Overtopping; Data repository
Info
Facilitating the re-use and exchange of experimental data. Task 10.1 Critical review. D10.2 Critical Review of data flux between laboratory models, numerical models and field case studies
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.2 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Field data; Numerical modeling data; Physical modeling data; Data flux
Info
Facilitating the re-use and exchange of experimental data. Task 10.2 Data Standards and Licenses. D 10.3 Data Standards Report
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.3 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data management options; Experimental data; Data formats
Info
Protocols for representing variability and unsteadiness in flume facilities. Deliverable Number 8.2
This deliverable is related to task 8.2
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Lemos, R.; Capitão, R.; Neves, M. G.; Reis, M. T. L. G. V.
Keywords: Extreme events; Climate change; Variability in flume facilities
Info
Sistema de previsão, alerta e gestão de riscos causados pela agitação marítima - Relatório inicial Arquitetura e características gerais do sistema para os portos de Madalena do Pico, São Roque do Pi
Neste relatório inicial são apresentadas a arquitetura e as caraterísticas gerais dos protótipos do sistema de previsão, alerta e gestão de riscos causados pela agitação marítima para os portos de Madalena do Pico, São Roque do Pico e Praia da Vitória. Os três protótipos em desenvolvimento têm por base uma arquitetura semelhante, com características distintas, nomeadamente no que respeita à localização dos dados de base, às malhas computacionais utilizadas e às características físicas das fronteiras, tanto no plano horizontal (interface terra-mar), como no vertical (batimetria dos fundos). Caracteriza-se o layout geral dos portos, bem como a sua morfologia e operabilidade.
Ano: 2018
Autor(es): Pinheiro, L.; Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.
Keywords: Porto de Praia da Vitória; Porto de São Roque do Pico; Porto de Madalena do Pico; Agitação marítima; Alerta e gestão de riscos; Sistema de previsão
|
|
|
Outros
Info
Risk Perception of Coastal Flooding in Praia da Vitória, Azores
The project LIFEGARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal unicipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in Praia da Vitória, Terceira, Azores, to understand the civilians perception of coastal flooding events.
Ano: 2024
Autor(es): Lima, L.; Fortes, C. J. E. M.; Zózimo, A. C.; Pinheiro, L.
Info
Social Surveys Indicating the Resilience of Urban Coastal Localities in Macaronesia to Coastal Flooding
The project LIFE-GARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal municipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in both localities in order to understand the civilians perception of coastal flooding events
Ano: 2024
Autor(es): Fortes, C. J. E. M.; Lima, L.; Zózimo, A. C.; Pinheiro, L.; Modino, R.; Barroso, J. G.; Cruz, C. G.; Comes, L.
Info
Avaliação da Estabilidade do Quebra-Mar Destacado do Porto Inglês (Ilha do Maio
Realização de ensaios em modelo físico reduzido 3D para a avaliação da estabilidade do quebra-mar destacado do Porto Inlgês, Maio, Cabo-Verde
Ano: 2023
Autor(es): Soares, R. E.; Fortes, C. J. E. M.; Lemos, R.; Costa, C.E.B.C.; Silva, L. G.; Pinheiro, L.; Neves, M. G.
Info
Physical modelling of wave-induced plant drag coefficient
N/A
Ano: 2019
Autor(es): Reis, R.; Suzuki , T.; LUBBERS, B.; Fortes, C. J. E. M.; Pires Silva, A.
Keywords: Flume experiments; Wave propagation; Plant flexibility; Vegetation
Info
Evaluation of wave overtopping consequences for risk assessment using ANP methodology
Adverse sea conditions can cause emergency situations associated to wave overtopping, which endanger the safety of people and goods, with negative impacts for society, the economy and the environment. Therefore, a methodology to assess the overtopping risk in port and coastal areas is essential for a proper planning and management of these areas.The Portuguese National Laboratory for Civil Engineering (LNEC) has been developing the HIDRALERTA system, an integrated decision-support tool for port and coastal management, which focus in preventing and supporting the management of emergency situations and the long-term planning of interventions in the study areas. It enables the user to calculate the risk for various port and coastal activities, starting with the characterization of sea-waves, wind field and tide levels at the study regions.HIDRALERTA was already tested at different places in Portugal: Costa da Caparica beach, in Almada, and port of Praia da Vitória, in the Azores. However, in both cases, the evaluation of wave overtopping / flooding consequences was carried out using a quite simple approach. In fact, such consequences were assessed only at a global and qualitative level, based on information provided by the responsible authorities.This paper aims at testing a quantitative methodology to evaluate overtopping consequences: the Analytic Network Process (ANP). This methodology was proposed to solve complex decision-making problems and its objective is to calculate the priorities among decision elements which will define their final weights on the consequences. The ANP approach can produce interdependencies between criteria and compute the respective weight of each criterion. Such a network model with dependence and feedback improves the priorities derived from judgements and makes prediction more accurate. So, the ANP allows comparison among clusters of elements. Furthermore, in this methodology we take into account the impacts of alternatives on the importance of criteria, by normalizing the comparison matrix. Thus, the given alternatives can influence the ranking of criteria.Application of the ANP methodology to the case study of Praia da Vitória port is presented and a consequences level map is obtained.
Ano: 2016
Autor(es): Lourenço, I.; Santos, J. A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Poseiro, P.; Craveiro, J.
Keywords: Praia da Vitória port; Analytic Network Process (ANP); Risk; Wave overtopping
Info
Sistema de alerta para a navegação em portos
Apresenta-se um novo sistema de alerta para navios amarrados em portos que se encontra em desenvolvimento no Laboratório Nacional de Engenharia Civil. O sistema SWAMS_ALERTA é um sistema de previsão e alerta baseado na avaliação do risco associado ao comportamento de navios amarrados em zonas portuárias.Os riscos associados a navios amarrados decorrem de movimentos excessivos, quer no plano horizontal, quer no plano vertical. Estes movimentos podem condicionar as atividades portuárias, nomeadamente cargas e descargas, mas em casos extremos podem levar à ocorrência de situações de emergência, tais como rotura de cabos, rotura de cabeços de amarração ou até colisões com o cais. As consequências deste tipo de situações envolvem sempre grandes prejuízos materiais e por vezes humanos.O sistema SWAMS_ALERTA utiliza as medições e previsões de agitação marítima para a determinação dos seus efeitos em termos de movimentos nos seis graus de liberdade e forças nas amarras e defensas quando o navio se encontra estacionado no cais. Para tal, o sistema recorre a uma série de modelos numéricos, interligados entre si. A comparação destes valores com valores máximos admissíveis pré-estabelecidos permite a avaliação, em tempo real, de situações de emergência e a emissão de alertas dirigidos às entidades portuárias.O sistema é constituído por 4 módulos:I
Ano: 2016
Autor(es): Pinheiro, L.; Lopes, P.; Fortes, C. J. E. M.; Santos, J. A.
Keywords: Navios amarrados; Riscos; Sistema de previsão e alerta
CONSTRUÇÃO DA EXPANSÃO DO PORTO DE SAL-REI 1ª FASE (ILHA DA BOAVISTA CABO VERDE) Ensaios bidimensionais em modelo reduzido Parecer Técnico
Info
Definição da Geometria para um Recife Artificial Multifuncional em Leirosa (Poster)
N/A
Ano: 2010
Número Páginas:
1.
Autor(es): Neves, M. G.; Antunes do Carmo, J.
Editor: Gestão Costeira: Vulnerabilidades e Riscos na Região Centro
Info
Probabilistic Assessment of Hazards from Overtopping of Seawalls in Urban Environments: Annual Report of pOST-dOCTORAL rESEARCH
N/A
Ano: 2005
Autor(es): Reis, M. T. L. G. V.
Editor: ******
Info
Guidelines and Recommendations for River Information Services - PIANC
N/A
Ano: 2004
Autor(es): J.A Covas
Editor: ******
|