Artigos de Revista
Info
Experimental investigation on the power capture of an oscillating wave surge converter in unidirectional waves
The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.
Ano: 2019
Número Páginas:
975-992pp.
Autor(es): Brito, M.; Ferreira, R. L.; Teixeira, L; Neves, M. G.; R. Canelas
Revista: Renewable Energy
Editor: Elsevier
Volume:
Volume 151.
Keywords: Power take-off: PTO damping; Response amplitude operator: RAO; Capture width ratio: CWR; Oscillating wave surge converter: OWSC; Wave energy
Info
Measuring wave run-up, overtopping and damage of rubble-mound breakwaters in scale model tests
A set of scale-model tests was carried out at the wave basin of the Leibniz University Hannover to extend the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater
Ano: 2019
Número Páginas:
118-129pp.
Autor(es): Santos, J. A.; Lemos, R.; Weimper, J.; Gronz, O.; Hofland, B.; Sande, J.; Pinheiro, L.; Spans, J.H.; Peña, E.; Reis, M. T. L. G. V.; Fortes, C. J. E. M.; Figuero, A.; Laiño, E.; Bornschein, A.; Kerpen
Editor: Hydralab+
Keywords: Rubble-mound breakwaters; Model tests; Overtopping; Wave run-up
Info
Numerical analysis of the interference between two elastically mounted cylinders in tandem subject to flows at low Reynolds numbers
Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.
Ano: 2019
Número Páginas:
11p.
Autor(es): Teixeira, P.; Rechsteiner, P.; Didier, E.
Revista: Journal of the Brazilian Society of Mechanical Sciences and Engineering
Editor: Springer
Volume:
Vol. 41.
Keywords: Finite element method; Vortex-induced vibration; Wake interference; Tandem arrangement; Circular cylinders
Info
Observação e monitorização de obras marítimas com a nova metodologia OSOM+
This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira
Ano: 2019
Número Páginas:
22p.
Autor(es): Fortes, C. J. E. M.; Capitão, R.; Henriques, M. J.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Silva, L. G.
Revista: Revista Mundi, Engenharia, Tecnologia e Gestão
Editor: Instituto Federal do Paraná
Volume:
v.4, n.2.
Keywords: Ericeira
Info
A methodology to determine the optimal size of a wells turbine in an oscillating water column device by using coupled hydro-aerodynamic models
This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.
Ano: 2018
Número Páginas:
9-18pp.
Autor(es): Torres, F.; Teixeira, P.; Didier, E.
Revista: Revista Renewable Energy
Editor: Elsevier
Volume:
Vol. 121.
Keywords: Air pressure control; Turbine sizing; Oscillating water column; Wave energy
Info
An integrated tool for modelling oscillating water column (OWC) wave energy converters (WEC) in vertical breakwaters
This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.
Ano: 2018
Número Páginas:
198
Autor(es): Mendonça, A. C.; Dias, J.; Didier, E.; Fortes, C. J. E. M.; Neves, M. G.; Reis, M. T. L. G. V.; Conde, J. M.; Poseiro, P.; Teixeira, P. R. F.
Revista: Journal of Hydro-environment Research
Editor: Elsevier
Volume:
Vol. 19.
Keywords: Wave power; SWAN-URANS models; Nonlinear numerical modelling; Physical modelling; Wave-structure interaction; Oscillating water column (OWC) wave energy converter (WEC)
Info
Asymmetric copula
Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula
Ano: 2018
Número Páginas:
304-334pp.
Autor(es): Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Vanem, E.; Reis, M. T. L. G. V.; Neves, L.
Revista: Wind Engineering
Editor: Sage
Volume:
Vol. 42, No. 4.
Keywords: Asymmetry; Crámer
Info
Characterization of ship motions induced by wake waves
This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the
Ano: 2018
Número Páginas:
547-555pp.
Autor(es): Pedro, F.; Pinheiro, L.; Fortes, C. J. E. M.; Santos, J. A.; Hinostroza , M.
Revista: Progress in Maritime Technology and Engineering
Editor: Taylor & Francis
Keywords: Wake waves; SWAMS; Ship motions
Info
Coastal risk forecast system
The run-up and overtopping by sea waves are two of the main processes that threaten coastal structures, leading to flooding, destruction of both property and the environment, and harm to people. To build early warning systems, the consequences and associated risks in the affected areas must be evaluated. It is also important to understand how these two types of spatial information integrate with sensor data sources and the risk assessment methodology. This paper describes the relationship between consequences and risk maps, their role in risk management and how the HIDRALERTA system integrates both aspects in its risk methodology. It describes a case study for Praia da Vito´ria Port, Terceira Island, Azores, Portugal, showing that the main innovations in this system are twofold: it represents the overtopping flow and consequent flooding, which are critical for coastal and port areas protected by maritime structures, and it works also as a risk assessment tool, extremely important for long-term planning and decision-making. Moreover, the implementation of the system considers possible known variability issues, enabling changes in its behaviour as needs arise. This system has the potential to become a useful tool for the management of coastal and port areas, due to its capacity to effectively issue warnings and assess risks.
Ano: 2018
Número Páginas:
26p.
Autor(es): Sabino, A.; Poseiro, P.; Rodrigues, A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Reis, R.; Araújo, J
Revista: Journal of Geographical Systems
Editor: Springer
Keywords: Software product lines; Geographic information systems; Early warning; Risk management; Coastal flooding; Wave overtopping
Info
Estudos em modelo reduzido de obras marítimas da Região Autónoma dos Açores
Atendendo ao seu caráter histórico, o presente artigo insere-se num conjunto de ações proposto pelo Departamento de Hidráulica e Ambiente (DHA) do Laboratório Nacional de Engenharia Civil (LNEC) com vista à comemoração dos 70 anos da sua existência, efeméride que se comemora durante o presente ano de 2018, e visa a apresentação de uma resenha da atividade desenvolvida no âmbito de estudos em modelos físicos de obras marítimas, pelo DHA desde a sua fundação, e para a Região Autónoma dos Açores (RAA). Pela sua insularidade, as populações da (RAA) estão naturalmente ligadas ao mar, nas suas mais diversas vertentes, muito dependendo a sua qualidade de vida das infraestruturas portuárias existentes em cada ilha, que permitem os indispensáveis movimentos de pessoas e de mercadorias e que muito contribuem para a coesão social e económica do arquipélago.Em virtude do papel decisivo assumido pelos portos na RAA, foi ao longo dos anos dada especial atenção à concepção destes equipamentos infraestruturais, tendo o LNEC desempenhado um papel relevante no capítulo reservado à verificação de projetos de obras marítimas de proteção portuária, especialmente através da realização de estudos em modelo físico reduzido, enquanto ferramenta mais válida para a concretização daquele objetivo, quer no passado, quer também no presente. Desde a fundação do Serviço de Hidráulica do LNEC, em 1948, foram inúmeros os estudos em modelo físico reduzido realizados para obras marítimas da RAA. O primeiro estudo em modelo reduzido de que há registo foi iniciado na segunda metade da década de 50, tendo o respetivo relatório do estudo sido publicado em março de 1958. Tratou-se de um estudo em modelo reduzido tridimensional (3D) com vista à definição do lay-out das obras marítimas de proteção do porto de Vila do Porto (Ilha de Santa Maria), em estrito cumprimento de requisitos que haviam sido estabelecidos, do ponto de vista da agitação marítima no interior da bacia portuária.Desde então, o LNEC foi chamado a intervir com a realização de ensaios em modelo reduzido em múltiplas situações, tendo-se assistido a uma especial concentração de atividade a partir do início da década de 80, coincidindo com o grande desenvolvimento portuário registado na Região.Ao longo dos 70 anos de vida do Departamento de Hidráulica e Ambiente (DHA) foram então efetuados, no LNEC e sob a orientação dos seus técnicos, 50 estudos em modelo físico reduzido de obras projetadas para a RAA, para todas as ilhas do arquipélago, com exceção da Ilha do Corvo.
Ano: 2018
Número Páginas:
24-31pp.
Autor(es): Silva, L. G.
Revista: Construção Magazine
Editor: Engenho e Média, Lda
Volume:
85.
Keywords: Portos; Modelação física; Açores
|
Comunicações
Info
Simulação da propagação de ondas regulares e irregulares em um canal bidimensional com praia numérica
Neste trabalho foram realizadas análises da propagação de ondas regulares e irregulares em um canal bidimensional com praia numérica através do modelo Fluent v. 16, desenvolvido pela ANSYS, que utiliza o método dos volumes finitos para a resolução das equações de conservação da massa e de movimento e o método Volume of Fluid para o rastreamento da posição da superfície livre. A praia numérica é baseada na adição de um termo de sumidouro na equação da quantidade de movimento que contém os coeficientes de amortecimento linear e quadrático. Para a aferição dos dois coeficientes, que dependem das características da onda incidente, foram simulados três casos de incidência de ondas regulares. De maneira geral, enquanto que o uso de baixos valores de coeficientes de amortecimento deixam ruídos numéricos no sinal da elevação da superfície livre, o uso de altos coeficientes de amortecimento causam reflexões das ondas incidentes. Diante dos resultados, adotou-se um coeficiente de amortecimento linear ótimo para as ondas regulares incidentes e manteve-se coeficiente de amortecimento quadrático nulo. Para esta situação, as séries temporais de elevação de superfície livre foram comparadas com séries temporais teóricas, mostrando uma excelente concordância entre elas. Após aferição da praia numérica, foi realizada a simulação com incidência de onda irregular definida pelo espectro do tipo JONSWAP. Analisando a evolução do espectro de energia e comparando-o com o imposto, verificou-se uma boa concordância entre os espectros medidos ao longo das sondas de monitoramento e o espectro imposto. Concluiu-se, através desse estudo, que o Fluent v. 16 e a metodologia utilizada permitem realizar a simulação da propagação de ondas regulares e, principalmente, irregulares em um canal bidimensional com praia numérica de forma adequada.
Ano: 2016
Número Páginas:
258-266pp.
Autor(es): Lisboa, R. C.; Teixeira, P.; Didier, E.
Editor: Universidade Federal do Rio Grande (FURG)
Keywords: Fluent; Ondas irregulares; Praia numérica; Propagação de ondas; Simulação numérica
Info
Sistema de alerta para a navegação em portos
Nesta comunicação, descreve-se um sistema de previsão e alerta baseado na avaliação do risco associado e ao comportamento de navios em manobra ou amarrados em zonas portuárias. Trata-se de uma extensão do HIDRALERTA (associado aos fenómenos de galgamentos oceânicos e inundações em zonas costeiras e portuárias), e tal como este, tem como ideia-base a utilização de previsões da agitação marítima (a 72 horas) para calcular os seus efeitos, neste caso, sobre os navios, quer nas manobras de aproximação ao porto quer quando se encontram acostados no interior deste. O sistema está a ser implementado numa plataforma Web e é constituído por 4 módulos: Características da Agitação Marítima; Navegação em zonas portuárias; Avaliação do risco e Sistema de Alerta. O porto da Praia da Vitória constitui a primeira aplicação prática do sistema e ilustra as suas potencialidades.
Ano: 2016
Número Páginas:
91-94pp.
Autor(es): Pinheiro, L.; Lopes, P.; Fortes, C. J. E. M.; Santos, J. A.; Poseiro, P.; Reis, M. T.
Editor: Instituto Hidrográfico
Keywords: Sistema de alerta; Previsão em tempo real; Navegação
Info
Sistema de alerta para a navegação no porto de praia da Vitória
Nesta comunicação, descreve-se o sistema SWAMS_ALERTA que é um sistema deprevisão e alerta baseado na avaliação do risco associado à navegação em zonas portuáriase ao comportamento de navios amarrados em zonas portuárias. O sistema baseia-se nosistema HIDRALERTA (associado aos fenómenos de galgamentos oceânicos e inundaçõesem zonas costeiras e portuárias), e tal como este, tem como ideia-base a utilização deprevisões da agitação marítima (a 72 horas) para calcular os seus efeitos, neste caso, sobreos navios, quer nas manobras de aproximação ao porto quer quando se encontra acostado nointerior deste.O sistema modular é constituído por 4 módulos: I
Ano: 2016
Número Páginas:
15p.
Autor(es): Pinheiro, L.; Lopes, P.; Fortes, C. J. E. M.; Poseiro, P.; Santos, J. A.
Editor: APRH
Keywords: Sistemas de informação geográfica; Sistema de alerta; Previsão em tempo real; Navegação
Info
Tanque de ondas numérico 3d para estudos de engenharia costeira
O objectivo principal deste artigo é implementar condições de fronteiras específicas num modelo URANS-VOF 3D (Unsteady Reynolds-Average-Navier-Stokes
Ano: 2016
Número Páginas:
1-10pp.
Autor(es): Didier, E.; Teixeira, P.; Neves, M. G.
Editor: Universidade Federal do Rio Grande (FURG)
Keywords: Batedores múltiplos com absorção activa; Tanque 3D; Absorção activa; Modelo RANS-VOF
Info
Toe berm damage progression analysis using a stereophotogrammetric survey technique
This paper focuses the toe berm damage progression analysis using image processing tools, in order to test their applicability to scale model tests. Damage can be characterized either by counting the number of displaced units or by measuring the eroded profile of the armor slope. Nevertheless, qualitative and quantitative damage assessment is not always easy. In order to ease and speed up those tasks, some image processing tools are applied in this study. In this work, damage was accessed using the displaced armor units counting method. A stereophotogrammetric method for profile survey was used to analyze profile eroded areas during test series. An image compare tool was alsp implemented and advantages and limitations of these techniques were evaluated. These techniques were applied ia scale model tests of Praia da Vitória harbor South breakwater, aiming to quantify the cross-section damage progression.
Ano: 2016
Número Páginas:
349-360pp.
Autor(es): Pedro, F.; Bastos, M.; Lemos, R.; Fortes, C. J. E. M.; Santos, J. A.
Editor: EdiBios
Keywords: Stereophotogrammetric survey; Damage progression; Breakwater
Info
Travel distance of wave overtopping at a rubble mound breakwater with a recurved wall: comparison between physical modelling and empirical formulas
The evaluation of the travel distance of wave overtopping behind coastal structures is very important for estimating the damaging impacts. Usually, these calculations can be performed by applying empirical formulas but they are limited to the wave/water level conditions and structure characteristics for which they were developed.This paper describes the application of existing formulas to a cross-section of the south breakwater of Praia da Vitória port (Terceira island, Azores, Portugal), which is protected by a recurved wave return wall.Results from physical model tests performed at LNEC are used to test, validate and calibrate those formulas. The formula that provided the best fit to the measured travel distances was developed by Besley (1999) but discrepancies were still considerable. Following a sensitivity analysis on the empirical parameters, new parameter values were suggested, as well as adjusted Besley (1999) and Lykke Andersen et al. (2009) formulas, which improved significantly the agreement with the new physical model data.
Ano: 2016
Número Páginas:
481-484pp.
Autor(es): Poseiro, P.; Reis, M. T.; Fortes, C. J. E. M.; Garcia, T.
Editor: Instituto Hidrográfico
Keywords: Wave overtopping; Praia da Vitória; Port structures; Empirical formulas; Physical modelling; Travel distance
Info
Warning system for navigation and moored ships in ports
This paper describes the SWAMS ALERT system, a forecast, warning and risk assessment system associated with navigation and mooring of ships in port areas. This system is based on HYDRALERTA, a previously developed system for overtopping and flooding in coastal and port areas. The basic idea is to use 72-hour sea waves
Ano: 2016
Número Páginas:
502-511pp.
Autor(es): Pinheiro, L.; Santos, J. A.; Fortes, C. J. E. M.; Lopes, P.; Poseiro, P.
Editor: Universidade Federal do Rio Grande (FURG)
Keywords: Praia da Vitória; Warning system; Ship
Info
Wave energy at Azores islands
This paper focus on the sea wave characterization (significant wave height, peak wave period, mean wave period, mean wave direction) at the Azores archipelago and the evaluation of the wave energy source. For the sea wave characterization, the numerical mode! SWAN, is applied for a period of 10 years in several points around each of the nine islands of Azores, at the 100 m CD bathymetric. Based on those results, average wave power maps considering whole 10 year period or the winter and the summer periods are constructed. An average sea wave climate is also presented. Moreover, sea wave characterization is also made for Porto Cachorro at Pico island, where a power pIant is constructed since 1990.
Ano: 2016
Número Páginas:
243-254pp.
Autor(es): Matos, A.; Madeira, F.; Fortes, C. J. E. M.; Didier, E.; Poseiro, P.; Jacob, J.
Editor: EdiBios
Keywords: Oscillating water column; Azores islands; Wave energy
Info
Avaliação do impacto económico dos galgamentos e inundação no porto da praia da Vitória
A avaliação quantitativa do risco de galgamentos, e correspondente inundação, em termos de custos associados aos danos causados por estes fenómenos é de grande relevância. Com efeito, tal dotará as autoridades competentes de uma informação fulcral para o planeamento a médio e longo prazo de intervenções mitigadoras do risco.Nesta comunicação, apresenta-se a aplicação da simulação de Monte Carlo ao porto da Praia da Vitória para a análise da incerteza das variáveis que influenciam o valor dos prejuízos causados pela ocorrência de galgamentos e inundação nesta zona portuária.A metodologia consiste na definição de um conjunto de variáveis aleatórias, tais como: o caudal médio galgado, a área atingida pelo galgamento, o valor e o número de bens em risco e o dano causado nos bens. A cada uma destas variáveis faz-se corresponder uma distribuição de probabilidade, procede-se à geração de uma amostra de valores aleatórios, aplica-se o modelo para cálculo do prejuízo associado ao galgamento utilizando as combinações geradas pelas variáveis aleatórias e, por fim, analisam-se os resultados para avaliação da incerteza nos mesmos. Com vista a simplificar a aplicação do modelo, esta foi dividida em 3 estágios, sendo o primeiro apenas para a geração da distribuição do caudal médio galgado condicionado ao nível da altura significativa do estado de agitação incidente na estrutura, o segundo para a determinação da distribuição correspondente ao custo condicionado ao mesmo nível e o terceiro para a obtenção da distribuição para o risco. A probabilidade de excedência de cada um dos níveis referidos é determinada, com base nos últimos 30 anos de previsões da agitação marítima obtidas nesta zona. Os caudais médios galgados sobre uma estrutura portuária são obtidos com recurso à ferramenta neuronal NN_OVERTOPPING2. Os restantes parâmetros foram definidos empiricamente apenas com o intuito de demonstrar o modelo.
Ano: 2015
Número Páginas:
15p.
Autor(es): Poseiro, P.; Santos, J. A.; Fortes, C. J. E. M.; Reis, M. T.
Editor: Carlos Coelho et al. Associação Portuguesa de Recursos Hídricos, 2015
Keywords: Simulação de Monte Carlo; Risco; Porto da Praia Vitória; NN_OVERTOPPING2; Inundação; Galgamentos
Info
Coastal risk forecast system
Runnup and overtopping are the two main sea wave originated events that threat coastal structures. Theseevents may cause destruction of property and the environment, and endanger people. To build early warning forecast systems, we must take into account the consequence and risk characterization of the events in the affected area, and understand how these two types of spatial information integrate with sensor data sources and the risk determination methodology. In this paper we present the description and relationship between consequence and risk maps, their role on the risk calculation, and how the HIDRALERTA project integrates both aspects into its risk methodology. We present a case study for Praia da Vitória port, in Azores Portugal.
Ano: 2015
Número Páginas:
201-209pp..
Autor(es): Sabino, A.; Rodrigues, A.; Poseiro, P.; Reis, M. T.; Fortes, C. J. E. M.; Reis, R.
Editor: SCITEPRESS
Keywords: Geographic information systems.; Consequence and risk maps,; Early warning,; Risk management,
|
|
Capítulos de Livros
Info
Multi-functional artificial reefs for coastal protection
N/A
Ano: 2009
Número Páginas:
153-210 pp.
Autor(es): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Teses de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Ano: 1999
Número Páginas:
159 p.
Autor(es): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Ano: 1998
Número Páginas:
594 p.
Autor(es): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Ano: 1998
Número Páginas:
346 p.
Autor(es): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Ano: 1973
Autor(es): Carvalho, M. M.
Editor: ******
|
|
Relatórios
Info
D1.1: Analysis of past extreme events, lessons learned ans SoA models V1
C2IMPRESS is a multi-disciplinary project which aims to enhance understanding and public awareness on multi-hazard risk, based on innovative models, methods, frameworks, tools and technologies to develop decision-making platforms with a fine-grained spatio-temporal data to better assess impacts, vulnerability and resilience on natural hazards. This Report is the Deliverable 1.1 and belongs to Work Package 1, which is mainly addressed to identify the past climate and physical processes that underlie natural disaster events and their consequences
Ano: 2023
Autor(es): Moragues, A.; Estrany, J.; Alves, E.; Zózimo, A. C.; Leitão, T. E.; Ruiz, M.; Oliveira, M. M.; Sfetsos, A.; Fernandes, T. F.
Info
Demonstration and technical tours plan
A major objective of TRA LISBON 2022 Conference is to boost research and innovation capacity for the transport sector, throughout a full innovation cycle, from idea to market. Having this in view, the project
Ano: 2022
Autor(es): Batista, F. A.; Marecos, V.; Antunes, M. L.; Macedo, A. L.; Freire, A. C.; Capitão, R.; Arsénio, E.; Maia, L.
Info
Demonstration submission and selection guidelines
The demonstration area will be one of the main focus points of TRA LISBON 2022, presenting multifunctional spaces and being prepared to receive a large number of different types of on-site demonstrations (indoor and outdoor). On-line demonstrations will also be an option, allowing for the widest possible coverage of access for all the participants.The dedicated areas will allow for interactive demonstrations of technological innovations to be carried out by and for industry partners, researchers, and other stakeholders. Demonstrations are an excellent opportunity to introduce conference attendees in an engaging way, as well as to promote new contacts and promising business.
Ano: 2022
Autor(es): Freire, A. C.; Arsénio, E.; Macedo, A. L.; Antunes, M. L.; Capitão, R.; Belinha, M.
Info
Technical tours organization criteria and procedures report
According to the CSA project plan, WP5.2 task objective is to organize technical tours that feature attractive and interactive showcases aiming at engaging participants into novel technologies for all transport modes and enabling stakeholders and their companies to disseminate and even sell their products and applications to all interested parties.
Ano: 2022
Autor(es): Capitão, R.; Macedo, A. L.; Arsénio, E.; Antunes, M. L.; Freire, A. C.
Editor: TRA LISBON 2022
Info
Data Repository Rules. Deliverable 10.4
This report is part of HYDRALAB+ Work Package 10, which seeks to strengthen the coherence of experimental hydraulic and hydrodynamic research undertaken by the HYDRALAB+ partner organisations. It outlines the work carried out by Samui Design & Management Ltd, supported by HR Wallingford, in relation to the development of a data repository structure that can be adopted by participants of the HYDRALAB+ project.
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data from physical modeling; Zenodo; Data repository structure
Info
Data Storage Report. RECIPE Task 8.2: Overtopping events in breakwaters under climate change scenarios
Reliable prediction of wave run-up/overtopping and structure damage is a key task in the design and safety assessment of coastal and harbor structures. Run-up/overtopping and damage must be below acceptable limits, both in extreme and in normal operating conditions, to guarantee the stability of the structure and the safety of people and assets on and behind the structure. The mean-sea-level rise caused by climate change and its effects on wave climate may increase the number and intensity of run-up/overtopping events and make the existing coastal/harbor structures more vulnerable to damage.Accurate estimates, through physical modelling, of the statistics of overtopping waves for a set of climate change conditions, are needed. The research project HYDRALAB+ (H2020-INFRAIA-2014-2015) gathers an advanced network of environmental hydraulic institutes in Europe, which provides access to a suite of environmental hydraulic facilities. They play a vital role in the development of climate change adaptation strategies, by allowing the direct testing of adaptation measures and by providing data for numerical model calibration and validation. The use of physical (scale) models allows the simulation of extreme events as they are now, and as they are projected to be under different climate change scenarios.The enclosed dataset refers to the experimental work developed at LNEC within HYDRALAB+ and considers 2D damage and overtopping tests for a rock armor slope, with four different approaches to represent storms. Data of free surface elevation, overtopping and damage is presented.
Ano: 2018
Autor(es): Fortes, C. J. E. M.; Mendonça, A. C.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Capitão, R.
Keywords: Climate change; Overtopping; Data repository
Info
Facilitating the re-use and exchange of experimental data. Task 10.1 Critical review. D10.2 Critical Review of data flux between laboratory models, numerical models and field case studies
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.2 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Field data; Numerical modeling data; Physical modeling data; Data flux
Info
Facilitating the re-use and exchange of experimental data. Task 10.2 Data Standards and Licenses. D 10.3 Data Standards Report
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.3 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data management options; Experimental data; Data formats
Info
Protocols for representing variability and unsteadiness in flume facilities. Deliverable Number 8.2
This deliverable is related to task 8.2
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Lemos, R.; Capitão, R.; Neves, M. G.; Reis, M. T. L. G. V.
Keywords: Extreme events; Climate change; Variability in flume facilities
Info
Sistema de previsão, alerta e gestão de riscos causados pela agitação marítima - Relatório inicial Arquitetura e características gerais do sistema para os portos de Madalena do Pico, São Roque do Pi
Neste relatório inicial são apresentadas a arquitetura e as caraterísticas gerais dos protótipos do sistema de previsão, alerta e gestão de riscos causados pela agitação marítima para os portos de Madalena do Pico, São Roque do Pico e Praia da Vitória. Os três protótipos em desenvolvimento têm por base uma arquitetura semelhante, com características distintas, nomeadamente no que respeita à localização dos dados de base, às malhas computacionais utilizadas e às características físicas das fronteiras, tanto no plano horizontal (interface terra-mar), como no vertical (batimetria dos fundos). Caracteriza-se o layout geral dos portos, bem como a sua morfologia e operabilidade.
Ano: 2018
Autor(es): Pinheiro, L.; Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.
Keywords: Porto de Praia da Vitória; Porto de São Roque do Pico; Porto de Madalena do Pico; Agitação marítima; Alerta e gestão de riscos; Sistema de previsão
|
|
|
Outros
Info
Risk Perception of Coastal Flooding in Praia da Vitória, Azores
The project LIFEGARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal unicipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in Praia da Vitória, Terceira, Azores, to understand the civilians perception of coastal flooding events.
Ano: 2024
Autor(es): Lima, L.; Fortes, C. J. E. M.; Zózimo, A. C.; Pinheiro, L.
Info
Social Surveys Indicating the Resilience of Urban Coastal Localities in Macaronesia to Coastal Flooding
The project LIFE-GARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal municipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in both localities in order to understand the civilians perception of coastal flooding events
Ano: 2024
Autor(es): Fortes, C. J. E. M.; Lima, L.; Zózimo, A. C.; Pinheiro, L.; Modino, R.; Barroso, J. G.; Cruz, C. G.; Comes, L.
Info
Avaliação da Estabilidade do Quebra-Mar Destacado do Porto Inglês (Ilha do Maio
Realização de ensaios em modelo físico reduzido 3D para a avaliação da estabilidade do quebra-mar destacado do Porto Inlgês, Maio, Cabo-Verde
Ano: 2023
Autor(es): Soares, R. E.; Fortes, C. J. E. M.; Lemos, R.; Costa, C.E.B.C.; Silva, L. G.; Pinheiro, L.; Neves, M. G.
Info
Physical modelling of wave-induced plant drag coefficient
N/A
Ano: 2019
Autor(es): Reis, R.; Suzuki , T.; LUBBERS, B.; Fortes, C. J. E. M.; Pires Silva, A.
Keywords: Flume experiments; Wave propagation; Plant flexibility; Vegetation
Info
Evaluation of wave overtopping consequences for risk assessment using ANP methodology
Adverse sea conditions can cause emergency situations associated to wave overtopping, which endanger the safety of people and goods, with negative impacts for society, the economy and the environment. Therefore, a methodology to assess the overtopping risk in port and coastal areas is essential for a proper planning and management of these areas.The Portuguese National Laboratory for Civil Engineering (LNEC) has been developing the HIDRALERTA system, an integrated decision-support tool for port and coastal management, which focus in preventing and supporting the management of emergency situations and the long-term planning of interventions in the study areas. It enables the user to calculate the risk for various port and coastal activities, starting with the characterization of sea-waves, wind field and tide levels at the study regions.HIDRALERTA was already tested at different places in Portugal: Costa da Caparica beach, in Almada, and port of Praia da Vitória, in the Azores. However, in both cases, the evaluation of wave overtopping / flooding consequences was carried out using a quite simple approach. In fact, such consequences were assessed only at a global and qualitative level, based on information provided by the responsible authorities.This paper aims at testing a quantitative methodology to evaluate overtopping consequences: the Analytic Network Process (ANP). This methodology was proposed to solve complex decision-making problems and its objective is to calculate the priorities among decision elements which will define their final weights on the consequences. The ANP approach can produce interdependencies between criteria and compute the respective weight of each criterion. Such a network model with dependence and feedback improves the priorities derived from judgements and makes prediction more accurate. So, the ANP allows comparison among clusters of elements. Furthermore, in this methodology we take into account the impacts of alternatives on the importance of criteria, by normalizing the comparison matrix. Thus, the given alternatives can influence the ranking of criteria.Application of the ANP methodology to the case study of Praia da Vitória port is presented and a consequences level map is obtained.
Ano: 2016
Autor(es): Lourenço, I.; Santos, J. A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Poseiro, P.; Craveiro, J.
Keywords: Praia da Vitória port; Analytic Network Process (ANP); Risk; Wave overtopping
Info
Sistema de alerta para a navegação em portos
Apresenta-se um novo sistema de alerta para navios amarrados em portos que se encontra em desenvolvimento no Laboratório Nacional de Engenharia Civil. O sistema SWAMS_ALERTA é um sistema de previsão e alerta baseado na avaliação do risco associado ao comportamento de navios amarrados em zonas portuárias.Os riscos associados a navios amarrados decorrem de movimentos excessivos, quer no plano horizontal, quer no plano vertical. Estes movimentos podem condicionar as atividades portuárias, nomeadamente cargas e descargas, mas em casos extremos podem levar à ocorrência de situações de emergência, tais como rotura de cabos, rotura de cabeços de amarração ou até colisões com o cais. As consequências deste tipo de situações envolvem sempre grandes prejuízos materiais e por vezes humanos.O sistema SWAMS_ALERTA utiliza as medições e previsões de agitação marítima para a determinação dos seus efeitos em termos de movimentos nos seis graus de liberdade e forças nas amarras e defensas quando o navio se encontra estacionado no cais. Para tal, o sistema recorre a uma série de modelos numéricos, interligados entre si. A comparação destes valores com valores máximos admissíveis pré-estabelecidos permite a avaliação, em tempo real, de situações de emergência e a emissão de alertas dirigidos às entidades portuárias.O sistema é constituído por 4 módulos:I
Ano: 2016
Autor(es): Pinheiro, L.; Lopes, P.; Fortes, C. J. E. M.; Santos, J. A.
Keywords: Navios amarrados; Riscos; Sistema de previsão e alerta
CONSTRUÇÃO DA EXPANSÃO DO PORTO DE SAL-REI 1ª FASE (ILHA DA BOAVISTA CABO VERDE) Ensaios bidimensionais em modelo reduzido Parecer Técnico
Info
Definição da Geometria para um Recife Artificial Multifuncional em Leirosa (Poster)
N/A
Ano: 2010
Número Páginas:
1.
Autor(es): Neves, M. G.; Antunes do Carmo, J.
Editor: Gestão Costeira: Vulnerabilidades e Riscos na Região Centro
Info
Probabilistic Assessment of Hazards from Overtopping of Seawalls in Urban Environments: Annual Report of pOST-dOCTORAL rESEARCH
N/A
Ano: 2005
Autor(es): Reis, M. T. L. G. V.
Editor: ******
Info
Guidelines and Recommendations for River Information Services - PIANC
N/A
Ano: 2004
Autor(es): J.A Covas
Editor: ******
|