Artigos de Revista
Info
Experimental investigation on the power capture of an oscillating wave surge converter in unidirectional waves
The aim of this paper is the experimental characterization of the capture width ratio (CWR) and response amplitude operator (RAO) of a 1:10 physical model of an oscillating wave surge converter (OWSC), under unidirectional regular and irregular waves. The effects of hydraulic power take-off (PTO) system are explicitly taken in consideration. A mathematical model is proposed to describe the PTO damping as a function of the angular velocity of the flap. The harmonic decomposition of free-surface elevation, angular velocity of the flap and pressure in the PTO system demonstrates that these signals are dominated by their linear component. However, the signals also present some important higher-order frequency components. To predict the CWR of the OWSC under irregular waves the nonlinear output frequency response functions are considered as the extension of the RAO to the nonlinear case. It is shown and discussed that the PTO system, wave frequency and height have a significant influence on the CWR and RAO. The RAO curve for irregular waves does not exhibit a well-defined peak, showing a limited variation in a broadband. A weak correlation between CWR and RAO was found, i.e., the maximum CWR does not occur for the maximum value of RAO.
Ano: 2019
Número Páginas:
975-992pp.
Autor(es): Brito, M.; Ferreira, R. L.; Teixeira, L; Neves, M. G.; R. Canelas
Revista: Renewable Energy
Editor: Elsevier
Volume:
Volume 151.
Keywords: Power take-off: PTO damping; Response amplitude operator: RAO; Capture width ratio: CWR; Oscillating wave surge converter: OWSC; Wave energy
Info
Measuring wave run-up, overtopping and damage of rubble-mound breakwaters in scale model tests
A set of scale-model tests was carried out at the wave basin of the Leibniz University Hannover to extend the range of wave steepness values analysed in run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions and on their effects on a gentler slope breakwater
Ano: 2019
Número Páginas:
118-129pp.
Autor(es): Santos, J. A.; Lemos, R.; Weimper, J.; Gronz, O.; Hofland, B.; Sande, J.; Pinheiro, L.; Spans, J.H.; Peña, E.; Reis, M. T. L. G. V.; Fortes, C. J. E. M.; Figuero, A.; Laiño, E.; Bornschein, A.; Kerpen
Editor: Hydralab+
Keywords: Rubble-mound breakwaters; Model tests; Overtopping; Wave run-up
Info
Numerical analysis of the interference between two elastically mounted cylinders in tandem subject to flows at low Reynolds numbers
Fluid-dynamic interference among cylindrical structures in arrays, frequently used in engineering, is of fundamental and practical interests since it may considerably change fluid-structure interactions and produce large fluctuating forces on structures that cause vibrations, lock-in and important motions. This paper aims to study the mutual interference between two circular cylinders in tandem arrangement, which is considered the simplest configuration of one array cylinders, elastically mounted in transversal direction and subject to a bi-dimensional uniform laminar flow at low Reynolds numbers. Both cylinders have the same diameter D and the center-to-center spacing is equal to L = 5.25D which corresponds to co-shedding regime. The academic numerical model Ifeinco, which is based on the finite element method and uses a partitioned scheme that considers two-way interaction of fluid flow and structure, has been employed to the analysis. Combinations of upstream and downstream stationary and elastically mounted cylinders are investigated for Reynolds number range from 90 to 140. Differences of flow behaviors drag and lift forces and resonance between single cylinder and cylinders in tandem arrangement were found. Mutual and respective influence of upstream cylinder motion on the downstream cylinder and vice-versa are analyzed. Results show that, in some engineering studies, the consideration of the flexibility of cylindrical structures in arrays is fundamental since it influences significantly the interference between cylinders, mainly the magnitude and direction of forces and characteristics of the resonance range, and, consequently, structural and dynamical behaviors.
Ano: 2019
Número Páginas:
11p.
Autor(es): Teixeira, P.; Rechsteiner, P.; Didier, E.
Revista: Journal of the Brazilian Society of Mechanical Sciences and Engineering
Editor: Springer
Volume:
Vol. 41.
Keywords: Finite element method; Vortex-induced vibration; Wake interference; Tandem arrangement; Circular cylinders
Info
Observação e monitorização de obras marítimas com a nova metodologia OSOM+
This paper describes a programme under the responsibility of the National Laboratory for Civil Engineering (LNEC), Portugal for the systematic observation and monitoring of maritime works, termed OSOM+, which has been applied to an extensive number of maritime structures on the Portuguese mainland coast and abroad. The OSOM+ programme comprises the following four main components for each structure: a) Periodic visual inspections by a trained technician; b) Periodic aerial inspections using a UAV/drone; c) The ANOSOM-GIS database, to store and/or query obtained information, as well as to diagnose present, evolution and risk conditions; and d) A mobile, portable, application, for real-time input and visualization of the ANOSOM-GIS database information.This recently updated methodology encompasses a number of tools whose functionalities are illustrated in this paper with an application to a case study: the Ericeira
Ano: 2019
Número Páginas:
22p.
Autor(es): Fortes, C. J. E. M.; Capitão, R.; Henriques, M. J.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Silva, L. G.
Revista: Revista Mundi, Engenharia, Tecnologia e Gestão
Editor: Instituto Federal do Paraná
Volume:
v.4, n.2.
Keywords: Ericeira
Info
A methodology to determine the optimal size of a wells turbine in an oscillating water column device by using coupled hydro-aerodynamic models
This paper describes a methodology to determine the optimal size of a Wells turbine to be used in an OWC device taking into account hydro-aerodynamic coupling, performance curves of the turbine and air pressure control by a relief valve. The proposed model, named turbine diameter optimization (TDO) model, considers the movement of the water surface inside the OWC chamber as a piston movement in response to the hydrodynamic forces from the incoming waves. The aerodynamic is based on the first law of thermodynamics applied to the air column of the chamber. The power-pressure curve of the turbine and the air pressure control by relief valve are implemented in the model to determine the turbine power output for several regular incident waves. The TDO model is initially calibrated by a numerical model based on Reynolds-Average-Navier-Stokes (RANS) equations for each wave component of an expected sea state distribution. Thereafter, the power output generated by turbines of several sizes is calculated with lower computational cost (few minutes) in comparison with RANS based models (thousands of hours) in a personal computer. This developed methodology is an important support to the process of turbine sizing for an OWC device for an expected sea state distribution.
Ano: 2018
Número Páginas:
9-18pp.
Autor(es): Torres, F.; Teixeira, P.; Didier, E.
Revista: Revista Renewable Energy
Editor: Elsevier
Volume:
Vol. 121.
Keywords: Air pressure control; Turbine sizing; Oscillating water column; Wave energy
Info
An integrated tool for modelling oscillating water column (OWC) wave energy converters (WEC) in vertical breakwaters
This paper describes the preliminary developments of an innovative integrated tool for the numerical modelling of oscillating water column (OWC) wave energy converters (WEC) integrated in vertical breakwaters. The main purpose of the tool is the numerical modelling of wave propagation from offshore to nearshore, wave-structure interaction, and the complex nonlinear hydrodynamic and aerodynamic phenomena that occur in OWC-WECs.The tool development and validation were supported by experimental data from physical model tests carried out in a wave flume at the Portuguese National Laboratory for Civil Engineering (LNEC). Prototype data were also available for the Pico OWC-WEC in the Azores, Portugal, monitored by the Portuguese Wave Energy Centre since 2005. Application of the tool for sea-wave characterization at the Azores archipelago and calculation of the corresponding wave power for a period of 10 years at various points around each island show that, in winter, there is good availability of wave energy in most quadrants of each island. In summer, the resource exploitation is only worthwhile on the north-west coasts of the islands. Physical and numerical modelling results for an OWC with a fully open chamber show good agreement between experimental data and numerical values for several incident wave conditions. The analysed results include the time series of the free-surface elevation at different locations, the time series of the mean free surface inside the water chamber, the amplification factors, the phase angles and the velocity vectors at the highest and the lowest positions of the mean free surface inside the chamber. The tool showed its potential to be useful in supporting ocean and coastal engineering projects due to its capacity to effectively reproduce the main phenomena involved in these types of studies.
Ano: 2018
Número Páginas:
198
Autor(es): Mendonça, A. C.; Dias, J.; Didier, E.; Fortes, C. J. E. M.; Neves, M. G.; Reis, M. T. L. G. V.; Conde, J. M.; Poseiro, P.; Teixeira, P. R. F.
Revista: Journal of Hydro-environment Research
Editor: Elsevier
Volume:
Vol. 19.
Keywords: Wave power; SWAN-URANS models; Nonlinear numerical modelling; Physical modelling; Wave-structure interaction; Oscillating water column (OWC) wave energy converter (WEC)
Info
Asymmetric copula
Joint statistical models for long-term wave climate are a key aspect of offshore wind engineering design. However, to find a joint model for sea-state characteristics is often difficult due to the complex nature of the wave climate and the physical constraints of seastates phenomena. The available records of wave heights and periods are often very asymmetric in their nature. This article presents a copula-based approach to obtain the joint cumulative distribution function of the significant wave heights and the up-crossing mean period. This study is based on 124-month hindcast data concerning Horns Rev 3 offshore wind farm. The extra-parametrization technique of symmetric copulas is implemented to account for the asymmetry present in the data. The analysis of the total sea, the wind-sea and primary swell components is performed separately. The results show that the extra-parametrization technique with pairwise copulas consistently provided a better goodness-of-fit when compared to symmetric copulas. Moreover, it is demonstrated that the separation of the total sea into its components does not always improve the extra-parametrized copula
Ano: 2018
Número Páginas:
304-334pp.
Autor(es): Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Vanem, E.; Reis, M. T. L. G. V.; Neves, L.
Revista: Wind Engineering
Editor: Sage
Volume:
Vol. 42, No. 4.
Keywords: Asymmetry; Crámer
Info
Characterization of ship motions induced by wake waves
This paper analyses the hydrodynamic interaction between two ships, one stationary and the other navigating nearby, using physical and numerical modelling. The passing ship is a self-propelled scale model of the
Ano: 2018
Número Páginas:
547-555pp.
Autor(es): Pedro, F.; Pinheiro, L.; Fortes, C. J. E. M.; Santos, J. A.; Hinostroza , M.
Revista: Progress in Maritime Technology and Engineering
Editor: Taylor & Francis
Keywords: Wake waves; SWAMS; Ship motions
Info
Coastal risk forecast system
The run-up and overtopping by sea waves are two of the main processes that threaten coastal structures, leading to flooding, destruction of both property and the environment, and harm to people. To build early warning systems, the consequences and associated risks in the affected areas must be evaluated. It is also important to understand how these two types of spatial information integrate with sensor data sources and the risk assessment methodology. This paper describes the relationship between consequences and risk maps, their role in risk management and how the HIDRALERTA system integrates both aspects in its risk methodology. It describes a case study for Praia da Vito´ria Port, Terceira Island, Azores, Portugal, showing that the main innovations in this system are twofold: it represents the overtopping flow and consequent flooding, which are critical for coastal and port areas protected by maritime structures, and it works also as a risk assessment tool, extremely important for long-term planning and decision-making. Moreover, the implementation of the system considers possible known variability issues, enabling changes in its behaviour as needs arise. This system has the potential to become a useful tool for the management of coastal and port areas, due to its capacity to effectively issue warnings and assess risks.
Ano: 2018
Número Páginas:
26p.
Autor(es): Sabino, A.; Poseiro, P.; Rodrigues, A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Reis, R.; Araújo, J
Revista: Journal of Geographical Systems
Editor: Springer
Keywords: Software product lines; Geographic information systems; Early warning; Risk management; Coastal flooding; Wave overtopping
Info
Estudos em modelo reduzido de obras marítimas da Região Autónoma dos Açores
Atendendo ao seu caráter histórico, o presente artigo insere-se num conjunto de ações proposto pelo Departamento de Hidráulica e Ambiente (DHA) do Laboratório Nacional de Engenharia Civil (LNEC) com vista à comemoração dos 70 anos da sua existência, efeméride que se comemora durante o presente ano de 2018, e visa a apresentação de uma resenha da atividade desenvolvida no âmbito de estudos em modelos físicos de obras marítimas, pelo DHA desde a sua fundação, e para a Região Autónoma dos Açores (RAA). Pela sua insularidade, as populações da (RAA) estão naturalmente ligadas ao mar, nas suas mais diversas vertentes, muito dependendo a sua qualidade de vida das infraestruturas portuárias existentes em cada ilha, que permitem os indispensáveis movimentos de pessoas e de mercadorias e que muito contribuem para a coesão social e económica do arquipélago.Em virtude do papel decisivo assumido pelos portos na RAA, foi ao longo dos anos dada especial atenção à concepção destes equipamentos infraestruturais, tendo o LNEC desempenhado um papel relevante no capítulo reservado à verificação de projetos de obras marítimas de proteção portuária, especialmente através da realização de estudos em modelo físico reduzido, enquanto ferramenta mais válida para a concretização daquele objetivo, quer no passado, quer também no presente. Desde a fundação do Serviço de Hidráulica do LNEC, em 1948, foram inúmeros os estudos em modelo físico reduzido realizados para obras marítimas da RAA. O primeiro estudo em modelo reduzido de que há registo foi iniciado na segunda metade da década de 50, tendo o respetivo relatório do estudo sido publicado em março de 1958. Tratou-se de um estudo em modelo reduzido tridimensional (3D) com vista à definição do lay-out das obras marítimas de proteção do porto de Vila do Porto (Ilha de Santa Maria), em estrito cumprimento de requisitos que haviam sido estabelecidos, do ponto de vista da agitação marítima no interior da bacia portuária.Desde então, o LNEC foi chamado a intervir com a realização de ensaios em modelo reduzido em múltiplas situações, tendo-se assistido a uma especial concentração de atividade a partir do início da década de 80, coincidindo com o grande desenvolvimento portuário registado na Região.Ao longo dos 70 anos de vida do Departamento de Hidráulica e Ambiente (DHA) foram então efetuados, no LNEC e sob a orientação dos seus técnicos, 50 estudos em modelo físico reduzido de obras projetadas para a RAA, para todas as ilhas do arquipélago, com exceção da Ilha do Corvo.
Ano: 2018
Número Páginas:
24-31pp.
Autor(es): Silva, L. G.
Revista: Construção Magazine
Editor: Engenho e Média, Lda
Volume:
85.
Keywords: Portos; Modelação física; Açores
|
Comunicações
Info
Analysis of the incident sea-waves and of the consequent run-up in the RODBreak experiment
In 2017, the RODBreak experiment was conducted. The experiment aimed at characterizing wave run-up, overtopping and damage in rubble-mound breakwaters. The reason for these experiments was the huge impact that climate can have on maritime structures, particularly in rubble mound breakwaters. In fact, the forecast sea level rise associated with more frequent and severe storms will have consequences either on the increase of wave runup, wave overtopping or on damage on existent structures since they were not design for those extreme values. However, for those climate change scenarios, little is known about the actual failure probability of such structures.Within this framework, a stretch of a rubble-mound breakwater was built in a wave basin. Under extreme wave conditions, with different incident wave angles (from 40° to 90°), a total of 49 tests were performed. Each test had different testing parameters, such as significant wave height (Hs), peak period (Tp) and wave direction. Also, for each test, different types of measurements were considered. Incident sea waves were measured with 3 arrays of 6 acoustic wave probes each as well as with isolated acoustic wave probes and 5 Acoustic Doppler Velocimeters (ADV
Ano: 2019
Número Páginas:
152-157pp.
Autor(es): Spans, J.H.; Santos, J. A.; Fortes, C. J. E. M.; Pinheiro, L.
Editor: EdiBios
Keywords: Run-up; RODBreak
Info
Analysis of wave overtopping on an impermeable coastal structure using a RANS-VOF numerical model
The global warming is responsible for increasing the sea level and, consequently, can cause overtopping on coastal structures. The prediction of this phenomenon is difficult because involves turbulence, wave breaking and run-up. The objective of this study is to analyze numerically the wave overtopping on coastal structures by using the FLUENT® numerical model, which is based on Reynolds-Averaged Navier-Stokes equations (RANS) and uses the Volume of Fluid method (VoF) to track the interface between water and air. Influences of mesh size, turbulence model (k-
Ano: 2019
Número Páginas:
10p.
Autor(es): Santos, G.C.; Teixeira, P.; Didier, E.
Editor: ABCM
Keywords: RANS-VoD; CFD simulation; Wave-structure interaction; Overtopping; Breakwater
Info
ANOSOM-WEB - uma plataforma web para a análise e observação sistemática de obras marítimas
Os quebra-mares de talude são estruturas normalmente utilizadas para proteção costeira e portuária e estão sujeitas durante a sua vida útil a diferentes solicitações (p.e., agitação marítima). A avaliação do seu estado estrutural e a previsão do seu comportamento ao longo do tempo torna-se fundamental para evitar significativos prejuízos materiais. É nesse âmbito que se insere o programa de observação sistemática, em curso no LNEC, desde 1986, para quebra-mares localizados em Portugal Continental, nos quais o Laboratório Nacional de Engenharia Civil (LNEC) realiza inspeções periódicas e avalia as respetivas condições de segurança. Para apoio a esse programa foi densenvolvida no LNEC a aplicação ANOSOM, a qual tem sofrido, ao longo dos tempos, diversas atualizações com vista a acompanhar a evolução que o programa OSOM+ tem vindo a sofrer. Esta comunicação descreve as funcionalidades da mais recente versão desta aplicação, a ANOSOM-WEB, como ferramenta de gestão de risco em estruturas de proteção costeira.
Ano: 2019
Número Páginas:
5p.
Autor(es): Martins, T.; Capitão, R.; Lemos, R.; Fortes, C. J. E. M.
Editor: APRH
Keywords: OSOM+; Base de dados; ANOSOM-WEB; Quebra-mares
Info
Damage assessment in rubble-mound breakwaters under oblique wave incidence
Regarding the stability of armour layers, several authors have proposed guidelines on how toconsider the effects of oblique waves (e.g. Yu et al., 2002, Van Gent, 2014; Maciñeira &Burcharth, 2016). Especially for very oblique waves, for which the increase in stability is thelargest, limited data are available. Under the scope of the HYDRALAB+ transnational accessproject
Ano: 2019
Número Páginas:
7p.
Autor(es): Lemos, R.; Peña, E.; Santos, J. A.; Sande, J.; Figuero, A.; Alvarellos, A.; Laiño, E.; Reis, M. T. L. G. V.; Fortes, C. J. E. M.; Kerpen, N.B.
Editor: EdiBios
Keywords: Large scale experiments; Measuring techniques; Surveying; Stability; Coastal structure
Info
Desenvolvimentos iniciais do projeto To-Sealert: galgamento e inundação em zonas portuárias e costeiras
O desenvolvimento de capacidade para prever a agitação marítima ao nível das bacias oceânicas com alguns dias de antecedência estimulou o aparecimento de sistemas informáticos para previsão dos efeitos da agitação marítima em zonas costeiras e portuárias. O HIDRALERTA é um desses sistemas: partindo das características da agitação marítima ao largo e utilizando modelos numéricos para a propagação da agitação marítima estima os parâmetros relevantes da agitação marítima para a avaliação do galgamento e do espraiamento quer em zonas portuárias, quer em zonas costeiras. O projeto de investigação e desenvolvimento To-SEAlert financiado pela Fundação para a Ciência e a Tecnologia e envolvendo o LNEC, a FCiências.ID, a NOVA.ID.FCT e o ISEL pretende melhorar as funcionalidades daquele sistema no que se refere às metodologias de previsão do galgamento e da delimitação da zona inundada, bem como no apoio à resposta a situações de emergência envolvendo aquele fenómeno.Esta comunicação pretende descrever o racional que justifica a existência do projeto, as tarefas em que o mesmo foi dividido e os principais resultados esperados.
Ano: 2019
Número Páginas:
4p.
Autor(es): Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Santos, J. A.; Poseiro, P.; Capitão, R.; Pinheiro, L.; Lemos, R.; Fonseca, A. M.; Barateiro, J.; Serrazina, V.; Craveiro, J.; Ferreira, J.; DUARTE, C.M.; And
Editor: APRH
Keywords: Emergência; Previsão e alerta; Inundação; Galgamento; Hidralerta
Info
Diagnóstico de quebra-mares baseado em observações visuais e levantamentos aéreos com drone
Neste artigo descreve-se a metodologia atualmente existente no Laboratório Nacional de Engenharia Civil (LNEC) de observação e monitorização sistemática de obras marítimas, que tem sido aplicada com sucesso a um grande número de estruturas marítimas na costa continental portuguesa e no estrangeiro.A atual metodologia (OSOM+) de diagnóstico de quebra-mares para avaliação dos estados atual, de evolução e de risco, complementa a anterior (OSOM), baseada somente em observações visuais, utilizando agora também a informação obtida com as inspeções com drone. Os resultados obtidos com as observações de drone, nomeadamente as fotografias aéreas verticais, os ortomosaicos e a nuvens de pontos, a partir das quais são construídos os modelos digitais de superfície das estruturas, permitem melhor avaliação do dano.Para ilustrar a aplicação da atual metodologia de avaliação de segurança de quebra-mares, usam-se os resultados da campanha de levantamento aéreo realizada em setembro de 2018 no quebra-mar poente da entrada do porto de Portimão.
Ano: 2019
Número Páginas:
4p.
Autor(es): Capitão, R.; Lemos, R.; Fortes, C. J. E. M.; Neves, M. G.; Silva, L. G.; Henriques, M. J.
Editor: APRH
Keywords: Diagnóstico e segurança de quebra-mares; Inspeções com drone; OSOM+
Info
Ensaios de agitação no porto de Leixões em cenário de alteração climática
Para caracterizar a agitação marítima no Porto de Leixões após o prolongamento do quebra-mar exterior, sob condições de alterações climáticas foi realizado um extenso grupo de ensaios em modelo físico tridimensional de agitação, num tanque do LNEC, à escala 1:80, representando-se toda a bacia portuária e o prolongamento do quebra-mar exterior do Porto de Leixões. Foram realizados ensaios com diferentes condições de agitação incidente para o rumo W e com dois níveis de maré, que correspondem ao nível médio e a preia-mar com uma sobrelevação representativa dos efeitos das alterações climáticas e da sua influência na agitação marítima . Foi medida a agitação em 30 pontos localizados na entrada do porto e no interior da bacia portuária e analisou-se o abrigo da bacia portuária com a ampliação do quebra-mar norte e as diferenças entre o abrigo para os dois níveis de maré ensaiados.As principais conclusões dos ensaios realizados foram que os maiores valores de alturas de onda ocorreram na zona exterior e de entrada do porto, diminuindo para o seu interior. Ao longo do canal de navegação, as alturas de onda vão diminuindo e no interior do porto obtiveram-se valores da altura de onda pequenos. A subida do nível do mar, para as condições ensaiadas, não afeta significativamente a agitação no interior da bacia portuária. No entanto, no exterior e zona de entrada do porto contribui para alterações da agitação que diferem consoante o período de pico e a altura de onda significativa incidente.
Ano: 2019
Número Páginas:
221-232pp.
Autor(es): Silva, M.; Fortes, C. J. E. M.; Lemos, R.; Neves, M. G.; Caeiro, C.
Editor: ISEP
Keywords: Modelo físico; Agitação; Porto de Leixões
Info
Estudo em modelo reduzido do espraiamento, galgamento e dano em quebra-mares de talude
A caraterização da rebentação / espraiamento / galgamento e do seu impacto na estabilidade de quebra-mares de taludes, quer no tronco, quer na cabeça, ainda é deficiente para cenários de alterações climáticas. O mesmo acontece com a influência nestes fenómenos de grandes ângulos de incidência da agitação marítima. A experiência RODBreak envolveu uma equipa de 23 pessoas de 8 instituições europeias e pretendeu criar um conjunto de dados para:- estender ou melhorar a gama de validade das fórmulas empíricas existentes para a estabilidade do manto protetor, o que facilitará a avaliação do desempenho das estruturas existentes;- calibrar e validar fórmulas empíricas para o espraiamento e galgamento, bem como modelos numéricos para a interação onda-estrutura.Além disso, esta foi uma oportunidade única para testar e melhorar algumas técnicas não intrusivas para medir quantidades relacionadas com aqueles fenómenos. Esta comunicação descreve os testes realizados no tanque de ondas 3D do Ludwig-Franzius-Institut für Wasserbau, Ästuar- und Kusteningenieurwesen da Leibnitz Universität Hannover em outubro e novembro de 2017.
Ano: 2019
Número Páginas:
245-255pp..
Autor(es): Santos, J. A.; Pedro, F.; Coimbra, M.; Figuero, A.; Fortes, C. J. E. M.; Sande, J.; Körner, M.; Lemos, R.; Bornschein, A.; Weimper, J.; van den Bos, J.; Dost, B.; Hofland, B.; Carvalho, R.; Alvarellos
Editor: ISEP
Keywords: Quebra-mares de talude; Galgamento; Run-up
Info
Extensão do molhe norte do porto de Leixões: modelação física de um navio amarrado no posto A
O Porto de Leixões, localizado na costa norte de Portugal, é um dos maiores do país, recebendo diariamente um grande número de navios de grandes dimensões. Um dos principais postos de acostagem situa-se à entrada do porto e encontra-se sujeito à agitação marítima que é difratada pelo olhe principal de proteção do porto. Para avaliar dos movimentos induzidos no navio estacionado nesse posto de acostagem e as forças exercidas nas suas amarras e defensas pela agitação incidente, utilizou-se o modelo físico de Leixões, construído num dos tanques do LNEC. Neste modelo físico, encontra-se representada a envolvente do porto de Leixões, assim como a sua batimetria. O modelo do navio
Ano: 2019
Número Páginas:
233-243pp.
Autor(es): Pinheiro, L.; Pedro, F.; Abdelwahab, H.S.; Fortes, C. J. E. M.; Santos, J. A.; Capitão, R.
Editor: ISEP
Keywords: Porto de Leixões; Modelo físico; Navio amarrado
Info
Hidralerta system: application to the Madalena do Pico and S. Roque do Pico ports
Under the framework of the ECOMAPORT project, two new prototypes of the forecast, early warning and risk management HIDRALERTA system to the ports of Madalena do Pico and S. Roque do Pico, both on the Island of Pico, Azores are undergoing. Those prototypes are intended to assess and predict, on a regular basis, the risk of coastal overtopping and consequent flooding and the risk to navigation, in particular as regards the safety of moored and maneuvered vessels, both caused by wave agitation. Additionally, it is intended to guarantee the functionality of the prototype of the HIDRALERTA system currently implemented in the port of Praia da Vitória, in Terceira Island, Azores since 2015, and to implement a new aspect regarding navigation risk.The new prototypes are based on the methodology already developed for the port of Praia da Vitória, where the first prototype of the HIDRALERTA system has been in operation since 2015.This paper essentially describes the work carried out to date on the system and their application to the ports of S. Roque do Pico and Madalena do Pico.
Ano: 2019
Número Páginas:
126-131pp.
Autor(es): Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Poseiro, P.; Pinheiro, L.; Mendonça, A. C.; SALVADOR, M.; Reis, F.; Azevedo, E. B.
Editor: EdiBios
Keywords: Azores; S. Roque do Pico; Madalena do Pico; Ecomaport; Hidralerta
|
|
Capítulos de Livros
Info
Multi-functional artificial reefs for coastal protection
N/A
Ano: 2009
Número Páginas:
153-210 pp.
Autor(es): Voorde, M.; Antunes do Carmo, J.; Neves, M. G.
Editor: Ch. A. Hudspeth, T. E. Reeve
|
Teses de Doutoramento
Info
Trapped-mode propagation along irregular coasts
N/A
Ano: 1999
Número Páginas:
159 p.
Autor(es): Santos, J. A.
Editor: ******
Info
Probabilistic Assessment of the Safety of Coastal Structures
N/A
Ano: 1998
Número Páginas:
594 p.
Autor(es): Reis, M. T.
Editor: ******
Info
Unsteady Nearshore Currents on Longshore Varying Topographies
N/A
Ano: 1998
Número Páginas:
346 p.
Autor(es): Sancho, F. E.
Editor: ******
Info
Simulação da agitação irregular. Técnicas matemáticas
N/A
Ano: 1973
Autor(es): Carvalho, M. M.
Editor: ******
|
|
Relatórios
Info
D1.1: Analysis of past extreme events, lessons learned ans SoA models V1
C2IMPRESS is a multi-disciplinary project which aims to enhance understanding and public awareness on multi-hazard risk, based on innovative models, methods, frameworks, tools and technologies to develop decision-making platforms with a fine-grained spatio-temporal data to better assess impacts, vulnerability and resilience on natural hazards. This Report is the Deliverable 1.1 and belongs to Work Package 1, which is mainly addressed to identify the past climate and physical processes that underlie natural disaster events and their consequences
Ano: 2023
Autor(es): Moragues, A.; Estrany, J.; Alves, E.; Zózimo, A. C.; Leitão, T. E.; Ruiz, M.; Oliveira, M. M.; Sfetsos, A.; Fernandes, T. F.
Info
Demonstration and technical tours plan
A major objective of TRA LISBON 2022 Conference is to boost research and innovation capacity for the transport sector, throughout a full innovation cycle, from idea to market. Having this in view, the project
Ano: 2022
Autor(es): Batista, F. A.; Marecos, V.; Antunes, M. L.; Macedo, A. L.; Freire, A. C.; Capitão, R.; Arsénio, E.; Maia, L.
Info
Demonstration submission and selection guidelines
The demonstration area will be one of the main focus points of TRA LISBON 2022, presenting multifunctional spaces and being prepared to receive a large number of different types of on-site demonstrations (indoor and outdoor). On-line demonstrations will also be an option, allowing for the widest possible coverage of access for all the participants.The dedicated areas will allow for interactive demonstrations of technological innovations to be carried out by and for industry partners, researchers, and other stakeholders. Demonstrations are an excellent opportunity to introduce conference attendees in an engaging way, as well as to promote new contacts and promising business.
Ano: 2022
Autor(es): Freire, A. C.; Arsénio, E.; Macedo, A. L.; Antunes, M. L.; Capitão, R.; Belinha, M.
Info
Technical tours organization criteria and procedures report
According to the CSA project plan, WP5.2 task objective is to organize technical tours that feature attractive and interactive showcases aiming at engaging participants into novel technologies for all transport modes and enabling stakeholders and their companies to disseminate and even sell their products and applications to all interested parties.
Ano: 2022
Autor(es): Capitão, R.; Macedo, A. L.; Arsénio, E.; Antunes, M. L.; Freire, A. C.
Editor: TRA LISBON 2022
Info
Data Repository Rules. Deliverable 10.4
This report is part of HYDRALAB+ Work Package 10, which seeks to strengthen the coherence of experimental hydraulic and hydrodynamic research undertaken by the HYDRALAB+ partner organisations. It outlines the work carried out by Samui Design & Management Ltd, supported by HR Wallingford, in relation to the development of a data repository structure that can be adopted by participants of the HYDRALAB+ project.
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data from physical modeling; Zenodo; Data repository structure
Info
Data Storage Report. RECIPE Task 8.2: Overtopping events in breakwaters under climate change scenarios
Reliable prediction of wave run-up/overtopping and structure damage is a key task in the design and safety assessment of coastal and harbor structures. Run-up/overtopping and damage must be below acceptable limits, both in extreme and in normal operating conditions, to guarantee the stability of the structure and the safety of people and assets on and behind the structure. The mean-sea-level rise caused by climate change and its effects on wave climate may increase the number and intensity of run-up/overtopping events and make the existing coastal/harbor structures more vulnerable to damage.Accurate estimates, through physical modelling, of the statistics of overtopping waves for a set of climate change conditions, are needed. The research project HYDRALAB+ (H2020-INFRAIA-2014-2015) gathers an advanced network of environmental hydraulic institutes in Europe, which provides access to a suite of environmental hydraulic facilities. They play a vital role in the development of climate change adaptation strategies, by allowing the direct testing of adaptation measures and by providing data for numerical model calibration and validation. The use of physical (scale) models allows the simulation of extreme events as they are now, and as they are projected to be under different climate change scenarios.The enclosed dataset refers to the experimental work developed at LNEC within HYDRALAB+ and considers 2D damage and overtopping tests for a rock armor slope, with four different approaches to represent storms. Data of free surface elevation, overtopping and damage is presented.
Ano: 2018
Autor(es): Fortes, C. J. E. M.; Mendonça, A. C.; Lemos, R.; Neves, M. G.; Reis, M. T. L. G. V.; Capitão, R.
Keywords: Climate change; Overtopping; Data repository
Info
Facilitating the re-use and exchange of experimental data. Task 10.1 Critical review. D10.2 Critical Review of data flux between laboratory models, numerical models and field case studies
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.2 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Field data; Numerical modeling data; Physical modeling data; Data flux
Info
Facilitating the re-use and exchange of experimental data. Task 10.2 Data Standards and Licenses. D 10.3 Data Standards Report
The HYDRALAB+ project is aimed at strengthening the coherence of experimental hydraulic and hydrodynamic research undertaken across its partner organisations. This report is D10.3 of the HYDRALAB+ project, entitled
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Neves, M. G.; Capitão, R.; Lemos, R.; Reis, M. T. L. G. V.
Keywords: Data management options; Experimental data; Data formats
Info
Protocols for representing variability and unsteadiness in flume facilities. Deliverable Number 8.2
This deliverable is related to task 8.2
Ano: 2018
Autor(es): Mendonça, A. C.; Fortes, C. J. E. M.; Lemos, R.; Capitão, R.; Neves, M. G.; Reis, M. T. L. G. V.
Keywords: Extreme events; Climate change; Variability in flume facilities
Info
Sistema de previsão, alerta e gestão de riscos causados pela agitação marítima - Relatório inicial Arquitetura e características gerais do sistema para os portos de Madalena do Pico, São Roque do Pi
Neste relatório inicial são apresentadas a arquitetura e as caraterísticas gerais dos protótipos do sistema de previsão, alerta e gestão de riscos causados pela agitação marítima para os portos de Madalena do Pico, São Roque do Pico e Praia da Vitória. Os três protótipos em desenvolvimento têm por base uma arquitetura semelhante, com características distintas, nomeadamente no que respeita à localização dos dados de base, às malhas computacionais utilizadas e às características físicas das fronteiras, tanto no plano horizontal (interface terra-mar), como no vertical (batimetria dos fundos). Caracteriza-se o layout geral dos portos, bem como a sua morfologia e operabilidade.
Ano: 2018
Autor(es): Pinheiro, L.; Fortes, C. J. E. M.; Reis, M. T.; Poseiro, P.
Keywords: Porto de Praia da Vitória; Porto de São Roque do Pico; Porto de Madalena do Pico; Agitação marítima; Alerta e gestão de riscos; Sistema de previsão
|
|
|
Outros
Info
Risk Perception of Coastal Flooding in Praia da Vitória, Azores
The project LIFEGARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal unicipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in Praia da Vitória, Terceira, Azores, to understand the civilians perception of coastal flooding events.
Ano: 2024
Autor(es): Lima, L.; Fortes, C. J. E. M.; Zózimo, A. C.; Pinheiro, L.
Info
Social Surveys Indicating the Resilience of Urban Coastal Localities in Macaronesia to Coastal Flooding
The project LIFE-GARACHICO (LIFE20 CCA/ES/001641) proposes the creation of an effective flexible adaptation framework for the coastal municipalities of Macaronesia, making specific local interventions to increase their resilience against extreme coastal events resulting from climate change. Social surveys were applied in both localities in order to understand the civilians perception of coastal flooding events
Ano: 2024
Autor(es): Fortes, C. J. E. M.; Lima, L.; Zózimo, A. C.; Pinheiro, L.; Modino, R.; Barroso, J. G.; Cruz, C. G.; Comes, L.
Info
Avaliação da Estabilidade do Quebra-Mar Destacado do Porto Inglês (Ilha do Maio
Realização de ensaios em modelo físico reduzido 3D para a avaliação da estabilidade do quebra-mar destacado do Porto Inlgês, Maio, Cabo-Verde
Ano: 2023
Autor(es): Soares, R. E.; Fortes, C. J. E. M.; Lemos, R.; Costa, C.E.B.C.; Silva, L. G.; Pinheiro, L.; Neves, M. G.
Info
Physical modelling of wave-induced plant drag coefficient
N/A
Ano: 2019
Autor(es): Reis, R.; Suzuki , T.; LUBBERS, B.; Fortes, C. J. E. M.; Pires Silva, A.
Keywords: Flume experiments; Wave propagation; Plant flexibility; Vegetation
Info
Evaluation of wave overtopping consequences for risk assessment using ANP methodology
Adverse sea conditions can cause emergency situations associated to wave overtopping, which endanger the safety of people and goods, with negative impacts for society, the economy and the environment. Therefore, a methodology to assess the overtopping risk in port and coastal areas is essential for a proper planning and management of these areas.The Portuguese National Laboratory for Civil Engineering (LNEC) has been developing the HIDRALERTA system, an integrated decision-support tool for port and coastal management, which focus in preventing and supporting the management of emergency situations and the long-term planning of interventions in the study areas. It enables the user to calculate the risk for various port and coastal activities, starting with the characterization of sea-waves, wind field and tide levels at the study regions.HIDRALERTA was already tested at different places in Portugal: Costa da Caparica beach, in Almada, and port of Praia da Vitória, in the Azores. However, in both cases, the evaluation of wave overtopping / flooding consequences was carried out using a quite simple approach. In fact, such consequences were assessed only at a global and qualitative level, based on information provided by the responsible authorities.This paper aims at testing a quantitative methodology to evaluate overtopping consequences: the Analytic Network Process (ANP). This methodology was proposed to solve complex decision-making problems and its objective is to calculate the priorities among decision elements which will define their final weights on the consequences. The ANP approach can produce interdependencies between criteria and compute the respective weight of each criterion. Such a network model with dependence and feedback improves the priorities derived from judgements and makes prediction more accurate. So, the ANP allows comparison among clusters of elements. Furthermore, in this methodology we take into account the impacts of alternatives on the importance of criteria, by normalizing the comparison matrix. Thus, the given alternatives can influence the ranking of criteria.Application of the ANP methodology to the case study of Praia da Vitória port is presented and a consequences level map is obtained.
Ano: 2016
Autor(es): Lourenço, I.; Santos, J. A.; Fortes, C. J. E. M.; Reis, M. T. L. G. V.; Poseiro, P.; Craveiro, J.
Keywords: Praia da Vitória port; Analytic Network Process (ANP); Risk; Wave overtopping
Info
Sistema de alerta para a navegação em portos
Apresenta-se um novo sistema de alerta para navios amarrados em portos que se encontra em desenvolvimento no Laboratório Nacional de Engenharia Civil. O sistema SWAMS_ALERTA é um sistema de previsão e alerta baseado na avaliação do risco associado ao comportamento de navios amarrados em zonas portuárias.Os riscos associados a navios amarrados decorrem de movimentos excessivos, quer no plano horizontal, quer no plano vertical. Estes movimentos podem condicionar as atividades portuárias, nomeadamente cargas e descargas, mas em casos extremos podem levar à ocorrência de situações de emergência, tais como rotura de cabos, rotura de cabeços de amarração ou até colisões com o cais. As consequências deste tipo de situações envolvem sempre grandes prejuízos materiais e por vezes humanos.O sistema SWAMS_ALERTA utiliza as medições e previsões de agitação marítima para a determinação dos seus efeitos em termos de movimentos nos seis graus de liberdade e forças nas amarras e defensas quando o navio se encontra estacionado no cais. Para tal, o sistema recorre a uma série de modelos numéricos, interligados entre si. A comparação destes valores com valores máximos admissíveis pré-estabelecidos permite a avaliação, em tempo real, de situações de emergência e a emissão de alertas dirigidos às entidades portuárias.O sistema é constituído por 4 módulos:I
Ano: 2016
Autor(es): Pinheiro, L.; Lopes, P.; Fortes, C. J. E. M.; Santos, J. A.
Keywords: Navios amarrados; Riscos; Sistema de previsão e alerta
CONSTRUÇÃO DA EXPANSÃO DO PORTO DE SAL-REI 1ª FASE (ILHA DA BOAVISTA CABO VERDE) Ensaios bidimensionais em modelo reduzido Parecer Técnico
Info
Definição da Geometria para um Recife Artificial Multifuncional em Leirosa (Poster)
N/A
Ano: 2010
Número Páginas:
1.
Autor(es): Neves, M. G.; Antunes do Carmo, J.
Editor: Gestão Costeira: Vulnerabilidades e Riscos na Região Centro
Info
Probabilistic Assessment of Hazards from Overtopping of Seawalls in Urban Environments: Annual Report of pOST-dOCTORAL rESEARCH
N/A
Ano: 2005
Autor(es): Reis, M. T. L. G. V.
Editor: ******
Info
Guidelines and Recommendations for River Information Services - PIANC
N/A
Ano: 2004
Autor(es): J.A Covas
Editor: ******
|